Search Documents

By F. J. Plecity, J. T. Michalak, W. C. Leslie

W. M. Williams (McGill University)-The authors are to be congratulated on completing this detailed investigation of recrystallization behavior. The present writer has recently completed some research at the University of Toronto on the recrystallization and grain growth behavior of a number of "pure" irons, and he would like to take issue with the authors' contention that recrystallization cannot be followed by means of hardness measurements. Two series of specimens of Ferrovac E, a com- mercially available iron, were annealed to complete recrystallization at 525" and 620" C, measurements being made both of Rockwell hardness and of volume percent recrystallized as a function of annealing time. Good correlation was found between these two quantities and, following the earlier practice of Cook and Richards for copper, hardness measurements were used in an extensive investigation of recrystallization. No anomalous behavior was observed as a result of this practice. Specimens which showed complete softening always showed, (metallographically and by X-rays), completely re-crystallized structures. These observations do not, of course, detract in the least from the results of the work under discus-

Jan 1, 1962

By K. A. Natarajan, I. Iwasaki

Platinum electrodes are not inert as often thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g, in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measure ments in water-oxygen, iron-water-oxygen, and manganese-water-oxygen systems. Stability relations between Fe++ and Fe (OH), and between Fe (OH), and Fe (OH), were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions. Platinum electrodes have often been used in the measurement of dissolved oxygen concentrations and of redox potentials (Eh) in a variety of fields, e.g., analytical chemistry,' corrosion," geology and mineralogy,,'' biology,"' sewage treatment,' * hydrometallurgy,"I" and flotation."la The effectiveness of Eh-pH diagrams, first reported by Pourbaix' in 1949, has contributed much towards the theoretical understanding of numerous problems encountered in the metallurgical industry. Not many references are available in the literature, however, wherein attempts have been made to confirm Eh-pH diagrams from experimental measurements. One reason might be that, in spite of the apparent simplicity of the electrochemical technique, the direct measurement of Eh involves complex practical problems.' Factors such as the purity of the solution, the type of electrodes used, the history of the indicator electrode, and the type of atmosphere (namely, oxidizing, reducing, or inert) do have effects on the measured Eh values. The influence of mixed potentials cannot be underestimated. The poisoning of platinum electrodes by organic and inorganic impurities present in the solution may lead to erratic results. Platinum, commonly thought to be an inert electrode material, is not really so, as attested by a number of previous investigators who advised caution concerning the anomalous behavior of platinum electrodes in various electrochemical measurements.'" In the present article, a few pertinent experiments related to Eh-pH measurements in systems of interest in the metallurgical and water pollution fields are described in an attempt to correlate such information with what is already known, especially in the electrochemical literature. Iron-water and manganese-water systems were selected with a view of studying the correspondence between experimentally observed and theoretically established equilibrium lines. The work included an investigation of the behavior of platinum electrodes with respect to pretreatment and adsorption characteristics, the measurement of dissolved oxygen concentrations and their relation to Eh, the determination of the electrode potential of the ferric-ferrous couple at different pH, and the measurement of oxidation potentials in iron-manganese leaching systems. Experimental Procedure A rotating platinum electrode was used in many of the measurements to study the effect of rotation on measured Eh values. The electrode made by the Pine Instrument Co. consisted of a stainless steel rod with a platinum disk soldered to the end. It was covered with a Teflon insulation along the sides, so that only the circular tip of the electrode was exposed to the solution. Prior to its use, the platinum surface was brightened on a metallurgical polishing wheel with alumina as an abrasive, unless specified otherwise. The electrode was rotated with a Sargent cone-drive motor at 350 rpm. The contact of the electrode with the external circuit was made by filling a notch at the top of the stainless steel shaft with mercury and by dipping a copper wire into the mercury pool. The performance of the rotating platinum electrode was compared with the performances of a Beckman platinum button electrode and a platinum wire electrode. All the potentials were measured with respect to a saturated calomel electrode. A saturated KC1-agar bridge was used to minimize the liquid junction potential. A Beckman Zeromatic pH meter together with a Beck-man electrode switch was used to measure both the Eh and pH. A double-walled, all-Pyrex jar with a capacity of about 1 liter and themostated by circulating water of constant temperature was used for a reaction cell. Four equally spaced ports in the cover provided access for a glass electrode, a salt bridge connecting the saturated calomel electrode, a dispersion tube for bubbling gases into the cell solution, inlet and outlet tubes for passing the desired gases over the solution, and a graduated burette for introducing reagents from outside. The rotating platinum electrode was inserted through an opening in the top-center of the cover, and a positive gas pressure was maintained inside the cell to prevent air from entering into the cell compartment. A magnetic stirrer was used to mix the solution inside. For the determination of dissolved oxygen in the test solutions, the polarographic techniquex was used.

Jan 1, 1971

"Acta Metallurgica" Dennis Carney, '59 Alfred Noble Joint Prize Committee F B Foley, Dec '61 American Association for the Advancement of Science F T Agthe, Dec '59, William L Fink, Dec '60 American Geological Institute Arthur Montgomery, Oct , '59, F C Kruger, Oct '60 American Power Conference J P Weir, T D Hess American Society for Testing Materials

Jan 1, 1959

By E. J. Rapperport, J. P. Pemsler

Proton irradiation of high-purity distilled berylliuwz was utilized to introduce various hydrogen contents from 0.00075 to 0.075 at. pct (0.83 to 83 ppm) in a band 0.004 cm wide. After irradiation, the specimens were heat-treated to effect hydrogen agglomeration. Observations of agglomerates in all specimens of the lowest hydrogen content indicate a hydrogen solubility of less than 0.83 ppm in the temperature range 350" to 1050°C. Estimates of the inter diffusion coefficient in the hydrogen solid solution of beryllium were obtained from measurements of the dimensions of hydrogen-depleted zones survounding agglomerated bubbles. A value of (approximately) 3 xlo-' sq cm per sec is obtained for the diffusion coefficient at 850" to 900°C. PREVIOUS investigators found that We solubility of hydrogen in beryllium is very small. Gulbransen and Andrew' state that beryllium does not react with hydrogen at 23 mm Hg between 300" and 900°C. Cotter ill et a1.' report that as-machined beryllium has an adsorbed hydrogen layer of 0.007 cu cm per sq cm of surface. No additional hydrogen is picked up in hydrogen at 0.1 mm Hg and between 200" and 80O°C, or when hydrogen is bubbled through molten beryllium. Beryllium hydride has been reported to exist in an ether solution,394 but decomposes at about 200°C; there is no substantial evidence for the existence of the hydride in the solid phase.

Jan 1, 1964

Further discussion of the paper of JAMES JOHNSTON, presented at the New York meeting, February,. 1914, and printed in Bulletin No. 85, January, 1914, pp. 107 to 133. See also Bulletin No. 91, July, 1914, pp. 1473 to 1496. THOMAS CROWE,* Victor, Colo.-The interest manifested of late in the treatment of low-grade ores, together with Mr. Clevenger's discussion of the Mill and Metallurgical Practice of the Nipissing Mining Co., prompts me to acid a few remarks relative to concentration in connection with cyanide treatment of low-grade ores. Mr. Clevenger in this discussion does not condemn concentration in this connection, but, nevertheless, the tone of his remarks would lead one to believe that his conclusions are like those of many others: that concentration is often turned to as a last resort in an attempt to improve or obtain an extraction upon an ore by the recovery and sale of the refractory portion of the ore. This, I will attempt to point out, is not always the case. Concentration in connection with cyanidation often performs an entirely different function, i.e., one of saving fine grinding. Economy being the keynote of successful treatment of low-grade ores, the problem often becomes more commercial than metallurgical, and, as there is generally a definite ratio existing between cost of operation, degree of comminution, and percentage of extraction, the grade of ore under treatment usually imposes a limit upon these factors. With many ores grinding is the most expensive single item in their treatment; therefore, the degree of comminution is very apt to be governed by the allowable cost of operation. With most ores the degree of comminution controls to a great extent the percentage of extraction. So in the treatment of low-grade ore it often becomes necessary to sacrifice extraction, through coarse grinding for the benefit of cost, in order that the greatest ultimate profit may be obtained, and it is under these conditions that it is, possible for concentration to play an important part in overcoming to some extent the effect of mesh. The precious metals occurring in an ore are usually closely associated with the metallic portion of the ore, and as this metallic portion is generally fairly well liberated from the gangue at comparatively coarse meshes, further grinding of the ore is necessary only in order that the metallic portion may be reduced sufficiently fine that the precious metal part of it may be dissolved by cyanide solutions in a reasonable length of time.

Jan 11, 1914

By Casper A. Nelson, Wendell M. Whitecotton

A WIDE variety of lead ore is treated by the Midvale Smelter, for it is a custom plant not only treating Company lead concentrate and direct-smelting ores but also custom ores and concentrates, principally from Utah, Idaho, and Nevada, with lesser amounts from Arizona, California, Colorado, Montana, Oregon, and Washington. The principal operating departments of the plant are weighing and sampling, Wedge roaster, D&L sintering, blast furnace and drossing, and baghouse. The lead bullion produced is shipped to a subsidiary, the U.S.S. Lead Refinery, Inc., at East Chicago, while the by-products, such as matte and speiss, are shipped to other smelters or re-treated at the plant.

Jan 1, 1948

By Thomas L. Kesler

THE Cartersville mining district, 35 miles northwest of Atlanta, Ga., has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. However, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magnesian limestone. GENERAL GEOLOGY Geologic relations of the ore deposits of this district are more or less similar to those of many Appalachian districts. The lowermost Cambrian formation, heretofore called Weisner1 in this region, supposedly partly or wholly equivalent to the Erwin and Hesse quartzites as recognized to the northeast, is overlain conformably by the Shady [+] formation, also of Lower Cambrian age. In the Cartersville district, the sedimentary rocks of these formations were folded with increasing intensity eastward, and were recrystallized.

Jan 1, 1940

By H. E. McKinstry

LIKE nearly everything else, mining geology has been reconverting. Many geologists had been in military and other government service. Many more, with mining companies, had been working primarily toward increasing production from known reserves. All of these are turning now toward their normal peacetime endeavor-the search for new ore; for most mining companies, finding themselves with accumulated deficits in development work, are more than ready to go ahead with their postwar plans made a year or more ago but still stalled at the close of 1945 for lack of man power. These plans include not merely development in the old home camp but also wide exploration for new prospects both domestic and foreign. Most of the large concerns have geologists and engineers in the field in the United States, despite the outlook for higher mining costs here, and at least half a dozen strong American companies are already investigating opportunities abroad, notwithstanding past unhappy experiences in certain Latin-American nations which have welcomed capital but later found means of preventing investors from reaping the reward of their enterprise. A few of these new foreign expeditions are following well-planned programs, but too many, in their haste to get any sort of footing, are proceeding without well-considered policy. with the result that their geologists can do little more than desultory scouting.

Jan 1, 1946

By R. E. Grant

THE Cerro de Pasco Railway Co., owned and operated by the Corporation, is a common carrier whose chief functions are transportation of ore and concentrates from the mines at Cerro de Pasco to the smelter in Oroya, and haulage of coal from the coal mines at Goyllarisquisga to the coal washery at Fundicion. Connecting with the Peruvian Central Railway at Oroya, the C. de P. Railway maintains joint, daily freight and passenger service from Lima and the port of Callao to Cerro de Pasco, terminal of the C. de P. main line and gateway to the Huanuco Valley. Extending from Oroya to Cerro de Pasco the main line is a standard-gauge roadbed of 70-lb. rail, 132 km. long with a maximum compensated grade of 2.25 per cent and a curvature of 16°, climbing from an elevation of 12,272 ft. above sea level at Oroya, lowest station on the line, to 14,208 ft. at Cerro de Pasco. The highest point reached by the C. de P. is on the coal branch at Alcacocha where the rails are 14,385 ft. above the sea.

Jan 1, 1945

By D. M. McFarland

IN mining, quarrying, and construction, drilling and blasting have an important influence on the operations that follow. If the fragmentation of material being disrupted is inadequate, loading and transportation equipment will not operate at or near full capacity. Any operator faced with this difficulty should not be satisfied until he is convinced by a careful study of his methods of drilling and blasting that no improvement can be made. Rock in a certain quarry in Ohio seemed to defy any grade of explosive or means of detonation that the explosives industry had to offer. The average result of a blast was that a great part of the burden would be pushed out from the face in a number of large sections that would jokingly be referred to as "boxcars." These were no credit to the explosives man and a costly problem for the quarry company. Such blocks retard shovel operation as they have to be uncovered and subjected to secondary drilling and blasting which, if extensive, is an expensive operation. It was an attempt to improve the fragmentation obtained in primary blasts that led to the development of milli-second-delay electric blasting caps. The reasoning that prompted the trial was that even with wide spacing of the drill holes it seemed that the burden was separated too quickly from the face by the cutting action of the explosives from hole to hole. If the time of firing of the holes could be regulated so that

Jan 1, 1948

By Roman Y. Poderny, Vladimir V. Rjevskii

In the USSR, the Moscow Institute of Radio Electronics tronics and Mining Electro-Mechanics (MIRGEM) has started what it hopes will become a nationwide movement to educate mining students in the precise specialties that industry has come to require. Courses for mining engineers, the MIRGEM faculty proposes, should dovetail as exactly as possible with specific jobs available in the mining profession. Acting upon this thesis, MIRGEM revised its own curriculum in 1962 and has since presented an over-all plan for Soviet mining education before two mining school conferences as well as the Ministry of Higher Education and a number of major Soviet industrial ministries. The plan was universally approved with some suggested revisions. SOVIET MINING EDUCATION TODAY At present, mining education in the Soviet Union covers the exploitation of solid minerals and raw materials, including coal as well as ferrous and nonferrous metals. The extraction, storage, and refining of oil and gas is treated as a separate discipline. In all, there are 33 Soviet universities and institutes that train mining engineers for careers in the industrial, research and educational fields.

Jan 9, 1966

Jan 1, 1917

By J. J. Pye, J. B. Drew

Mzasurements of the surface diffusion coefficients of metals have been made. Diffusion profiles for the Ag-Ag system were obtained by means of a radioactive point source and a precision auto-radiographic technique. The activation energy for silver self diffusion (=8.1 kcal per mole) is lower than that previously reported (-10 kcal per mole) on poly crystalline wire by Nickerson and Parker. The bresent data indicate an effect due to parasitic volume diffusion at temperatures above 500°C. RELATIVELY few measurements have been made of the surface self-diffusion coefficients of metals. Nickerson and arker' measured the diffusion of silver over the surface of poly crystalline wires and estimated that the activation energy was 10.3 kcal per mole. Winegard and chalmers2 carried out measurements on both polycrystalline and single crystal surfaces but did not report a value of the activation energy. They found, however, that at temperatures between 250" and 400°C the diffusion coefficients were on the order of lo-' sq cm per sec and that there was an acceleration of the migration of silver on the polycrystalline sample when a change of surface shape occurred. Winegard and Chalmers used an autoradiographic technique, hereafter designated ARG, and Nickerson and Parker used a surface scanning geiger counter in order to determine the diffusion profiles. More recently, Hackerman and simpson3 measured the surface self-diffusion coefficient of copper at a single temperature (750°C), and the value of the diffusivity (- 10-5 sq cm per sec) is in agreement with that given by jostein from his thermal grooving measurements. This paper reports the results of an investigation of the surface self-diffusion coefficients of silver over a large temperature range and describes the adaptation of autoradiographic (ARG) techniques for the determination of diffusion profiles obtained from a radioactive point source. EXPERIMENTAL PROCEDURE The experimental procedure is a modification of the method employed by Hackerman and simpson3 in their measurements on copper. A brief description of their technique is as follows: A radioactive needle which sinters to the surface during the diffusion an- neal serves as the source of diffusing atoms. After the diffusion run the needle is removed and the surface is scanned with a shielded counting arrangement. The diffusion profiles reported in this paper were obtained by a modification of the above procedure which employs a precision ARG technique. Previous investigations in this laboratory and elsewhere51B have shown that under carefully controlled developing conditions and by the use of calibration sources a linear relation exists between the concentration of the isotope and the photographic density for values below unity. The use of ARG under these conditions has advantages over the counter scanning method in that cumbersome shielding and requirements for great mechanical precision of the scanner are eliminated. Also the ARG gives a complete picture of the surface which is advantageous in studies of anisotropic diffusion. A recording microdensitometer having a 0.1 p wide slit was employed. At low temperatures the disturbing effects of subsurface radiations are negligible. The diffusion anneals are carried out in the cell shown in Fig. 1. The needle is formed by grinding down a 1.0 mm rod of high-purity silver until a tip of 0.2 mm radius or smaller is formed. This tip is plated withA"' which becomes the source of the diffusing atoms that are detected by ARG. The needle carrier and the crystal holder, Fig. 1 are constructed of quartz and ports are provided in the holder pedestal which allow free vapor circulation ((2.0 oz) and the carrier apron fits snugly over the crystal holder cap, insuring that the needle does not move and scratch the surface. Temperatures are provided by a stabilized tubular furnace which can be quickly positioned around the cell, thus bringing the crystal up to temperature in a time that is short compared to the diffusing times. The diffusion anneals range from 2 hr for the high-temperature samples to about 25 hr for those at the lowest temperature. The possibility of vapor transport of the radioactive metal as a contributing factor in the diffusion profile was investigated in two ways. One method was to suspend the needle directly over a dummy sample, raise the temperature, for periods of time equal to the diffusion times, and then take an auto-radiograph of the surface. Negligible radioactivity appeared. In the second method a thin slot in the crystal face on one side of the source provided a "cong path" for surface diffusion. If evaporation was the primary source of surface atoms the region of radioactivity around the source would be symmetrical. This was not the case. The profile dipped abruptly at the edge of the slot but on the other side of the source the usual diffusion profile appeared.

Jan 1, 1963

By S. R. Goodman, Hsun Hu

A detailed study of texture developmenf in poly crystalline copper atzd 70-30 brass has been completed. Textural changes as a function of deformation are shoum by pole jigmres and by intensity measurements oF- various rejlectiotzs from the rolling plane and the rolling direction. These examinations were accompanied by measurements of stacking fault frequency, hardness changes, and microstructure. Some of the results were briefly presented earlier. Additional results reported here are consistent with the idea that deformation faulting or slip by partial dislocations is of primary importance in the formation of deformation textures in fcc metals. lo examine the idea that deformation faulting is of primary importance in determining whether the texture is the copper type or the brass type an extensive study of the development of polycrystalline textures in copper and 70-30 brass was initiated. Besides the determination of complete pole figures, the intensities of the various reflections from both the rolling plane and the plane perpendicular to the rolling direction, the peak shifts due to deformation stacking faults, and the hardness of the rolled specimens were examined at various reductions from 10 to 99 or 99.5 pct. Mi-crostructures were examined by transmission electron microscopy. Some of the results were briefly presented in an earlier publication.' Since then, additional information has been obtained. This is given in the present paper. EXPERIMENTAL PROCEDURE Material and Specimen Preparation. The material used was a commercial electrolytic copper bar 1i in. wide and 2 in. thick and a 70-30 brass bar la in. wide and 1i in. thick. Chemical analysis indicated a purity of 99.97 pct for the copper, with 0.025 pct 0 as the major impurity. The 70-30 brass was of higher purity with 0.0016 pct 0 as the major impurity. Extreme care was taken in the preparation of the starting material to insure uniformly fine grains with a nearly random initial texture. The two bars were first cold-forged and then annealed to eliminate any original texture. The grains were then refined by several cold rolling (approx 30 pct reduction) and annealing treatments. The + -hr anneals were carried out in a salt bath at 390" to 440°C for copper and at 490°C for brass. The resulting penultimate grain size was 0.06 mm for copper and 0.03 mm for brass, and both showed very little preferred orientation. The number of prior cold rolling and annealing cycles was such that the final thickness after various final reductions of 10 to 95 (for brass) or 99 (for copper) pct was the same (0.020 in.). These annealed strips were rolled in two directions by reversing end for end between passes according to the following schedule: 0.006 in. per pass to 0.100 in., 0.003 in. per pass to 0.050 in., 0.002 in. per pass to 0.025 in., 0.001 in. per pass to 0.020 in. Texture Determination. The development of rolling textures was studied by examining complete pole figures determined from the (111) reflection. Specimens thinned from one face of the strip to half thickness (0.010 in.) were used to obtain the central portion of the pole figures, while specimens thinned from both faces to 0.003 in. were used to obtain the peripheral portion. The reflection and transmission techniques have been described previously. In addition to X-rav pole figures, texture development was also studied b; examining the intensity variation of the (Ill), (200), (2201, (311), (331), (420), and (442) reflections from the rolling plane and from the plane normal to the rolling direction, as a function of deformation. The same specimens used for the central portion of the pole figures were used for the intensity measurements of the various reflections from the rolling plane. For intensity measurements from the plane normal to the rolling direction, composite specimens were prepared by mounting sections cut parallel to the transverse direction of the strip. An epoxy resin was used to bond these sections together, and the entire composite was then mounted in a cold-setting resin to facilitate subsequent polishing and etching to remove distorted metal at the cut. The intensities were expressed in units of the integrated intensities measured from an annealed copper specimen having almost no preferred orientation. Stacking Fault Frequency Determination. Following the analysis of Warren: the stacking fault frequency, a, was determined from the change in the peak separation (A%) of two neighboring reflections of a deformed specimen, as compared with the normal peak separations of a fully annealed specimen. To obtain sufficient intensities for the second-order reflections, (222) and (400), composite specimens were prepared from parallel sections cut from the strip at 30 deg to the rolling direction for copper and 25 deg for the brass.* From texture data, these sections are known to contain a large population of both (111) and (200) planes. Since residual stresses can also cause X-ray line shifts (the direction of line shifts depends upon the sign of the stress), the use of composite specimens consisting of sectioned planes should help compensate for these effects as the residual stresses change sign from the surface to the central section of a rolled strip. Since the amount of peak shift is almost un-measurable in brass rolled 15 pct and in copper rolled

Jan 1, 1969

By W. J. Reagan

The problem of increasing output and decreasing percentage of rejections is a vital one in the manufacture of steel of any kind. The making of basic open-hearth steel for use in rolled steel wheels, tires for locomotive and car wheels, and forgings of various kinds, is a highly specialized industry. The increase in weight of railway rolling stock of all kinds, and the high speed that the public demands of transportation facilities, make it imperative that steel for use in this class of material shall be of the highest quality obtainable. During the past few years it has been the writer's good fortune to have opportunity to study the defects in basic open-hearth steel, and also the results obtained by various changes in open-hearth practice, on such defects. The opportunity for study and the details available are rarely found in the manufacture of steel of any kind. It seems reasonable to assume that many of the results determined here can be applied to the production of steel of other types with a decided improvement in quality, a decrease in the percentage of rejections and an increase in output. All of the material described is basic open-hearth steel with the following range of analysis: carbon, 0.50 to 0.85 per cent.; phosphorus and sulfur, 0.04 max.; silicon, 0.15 to 0.35; manganese, 0.50 to 0.75. All of this material is bottom-cast, therefore tapping and pouring temperatures are higher than in top-cast production. Ingots used in this type of work are of standard length with varying diameters. The ingot is known as duodecagonal, or twelve-sided. The standard body length is 88 in. and the hot top length, 14 in. Fig. 1 shows a typical ingot of this type. The diameter varies from 13 to 30 in. Ingots for special forgings, which cannot be made in molds of standard size, are made in molds of various sizes and designs. These ingots are sliced cold, into blocks of various lengths, depending upon the weight of the forging to be made. Fig. 2 shows the ingot after coming from the slicing lathe. Jusf sufficient metal remains between blocks to hold the ingot in one piece while it is being removed from the lathe; then steel wedges are inserted between the blocks and the blocks are broken apart. This affords abundant opportunity for inspection, as the interior of the

Jan 1, 1930

By W. L. Zeigler

THE tailing from the gravity concentration plant of the Hecla Mining Co., Gem, Idaho, was former-ly loaded into railroad cars to be used for ballast, highway surfacing material, or concrete work, or dis-posed of by an aerial tramway, which dumped it into another gulch. The tailing averages about 1.2 per cent lead and 0.8 oz. silver to the ton. Further treatment for the recovery of the valuable metals had been investigat-ed several times with results that did not warrant the construction of a retreatment plant; but early in 1925 experimental work was again started with small tests, and later with a 10 tons per day flotation test plant. This showed that the tailing could be ground and treat-ed by flotation at a profit. It was decided to make the new flotation plant an addition to, rather than incor-porate it in the old concentrator, the original capacity of which had been increased many times, the present arrangement being by no means ideal. The old mill buildings were of timber and board contruction, creat-ing more or less fire hazard, so all new construction was made fireproof. Construction work on the new plant was started in the middle of July, 1925, and the plant was placed in operation early in December. The building is of concrete and steel with hollow tile walls, steel sash and corrugated asbestos roofing. The ball-mill floor has for its foundation a cellular reinforced concrete block about 14 ft. deep, extending to cemented river gravel, and the cells filled with tailing to give weight to the block. Overhead, built into the steel frame, is a 5-ton hand-operated traveling crane. With both ball-mills running fully loaded, there is not the slightest trace of vibra-tion in the foundation or building. The flotation floor is of reinforced concrete beam construction and spans Canyon Creek. Adjustable plunger feeders are arranged under the the tailing-bin, which feed by gravity to a 14-in. eleva-tor, discharging to a short 18-in. conveyor. From the conveyor the tailing is discharged into a dividing hop-per, from which point the plant is arranged in three separate units. Each unit consists of a ball-mill in closed circuit with a classifier, and an 8-cell flotation machine and has an approximate capacity of 300 tons per 24 hours.

Jan 8, 1927

By AIME AIME

FREE competition, long the controlling ideal of domestic trade within the United States, has had the fundamental geographical advantage of functioning in the world's largest area of unrestricted commerce. Goods moved back and forth across state lines, unimpeded by customs, and industrial operations have developed rapidly to meet the expanding needs of a pioneer country richly endowed with natural resources. Fifty years ago, antitrust laws were adopted to protect the competitive private enterprise principle. It became illegal for one person to combine with another to restrain trade or commerce among the several states or with foreign nations. The original legislative measures defining this philosophy were the Sherman Act of 1890 and the Clay- ton Act passed in 1914. The development of Europe and other parts of the world was influenced by different conditions which led to a different theory of trade. Here were many small nations, with limited natural resources and a thin market, and they attempted to protect their national economy by tariff walls. International business arrangements for the purpose of diminishing the ups and downs of the more competitive system --crux of the modern cartel operations-seemed a logical device to stabilize production and guard the interests of both workers and consumers. European governments as well as European industrial interests became convinced that if com- petition could be held in bounds the danger of business depressions and un- employment could be reduced.

Jan 1, 1944

By Scott Turner

OUR Institute, in its annual Directory, states the following: The purpose of each Technical Committee is to further the development of the special mineral industries in its field, chiefly through obtaining and discussing papers suitable for publication by the Institute. The proper field of the new Health and Safety in Mines Committee is judged to include the entire mining industry, and involves the multitude of health and safety problems arising in all kinds of mining operations. The mining industry in the United States has made much progress during recent years in reducing accidents. This advance has been widespread, and has been especially notable in the mining of iron ore. Yet the statistics of the U. S. Bureau of Mines, when compared with figures of the National Safety Council for other industries, show that mining still has a higher personal mishap rate than any other major industry in this country. In addition, studies of dollars-and-cents cost of casualty occurrences indicate that an important part of our mining cost, held by various authorities to be as much as 10 per cent of the total, is due to accidents.

Jan 1, 1933

By I. E. Campbell, R. I. Jaffe

Oxygen, nitrogen, and hydrogen are known to be absorbed by titanium at elevated temperatures. Ehrlichl reports that about 30 at. pct oxygen can be dissolved in solid solution by alpha-titanium. Nitrogen also has a solid solubility in alpha-titanium, but there is no information as to its extent. The solid solubility of hydrogen in titanium also is high. Kirshfeld and Sieverts2 report 50 at. pct soluble, while Hägg3 reports about 33 at. pct hydrogen to be soluble in alpha-titanium. General statements are made in the literature that oxygen, nitrogen, and hydrogen embrittle titanium, but no quantitative measurements have been made of the effect of these gases on the mechanical properties of the metal. One reason for this is the lack of a source of titanium pure enough to be considered a suitable starting material. Iodide-refined titanium, made by thermal decomposition of titanium iodide vapor on an incandescent wire,4 contains small amounts of carbon, silicon, iron, and aluminum, but is very low in oxygen, nitrogen, and hydrogen content, and, therefore, was used in this work. A further reason for the lack of quantitative information on the effect of these gases, particularly oxygen, is the difficulty of carrying out accurate analytical determinations at the low concentrations of interest in this work. For this reason, the oxygen, nitrogen, and hydrogen were added in measured amounts as gases, and diffused into the titanium, to avoid the necessity of chemical analysis. The purpose of the work reported here was to isolate and measure the effects of oxygen, nitrogen, and hydrogen on titanium of the highest purity available at the time. The concentrations studied were 0.25, 0.5, and 1 at. pct in each case. Experimental Work One-half of a 24-in. hairpin of iodide-refined titanium was available for this work. The rod was approximately 0.25-in. in diam and had a 0.003-in.tung sten core. From chemical and spectro-graphic analyses, the purity of the sample was estimated to be between 99.80 and 99.95 wt pct. The chief impurities (aside from the tungsten core) were iron (0.04 pct), silicon (0.01-0.1 pct), aluminum (0.05 pct), carbon (0.03 pct). The tungsten core constituted 0.05 pct by weight of the sample. Although some alloying undoubtedly took place between the tungsten and the titanium during the deposition reaction, the core remained substantially intact in the deposited metal. The initial average hardness of the titanium as deposited was 105 Vickers (10-kg load). The maximum hardness was 116 Vickers and the minimum 91 Vickers. The metal was somewhat harder than that currently being obtained by the iodide process, that is, 75-90 Vickers. The rod was cold swaged to ¼-in. diam and then cold rolled in diamond shaped rolls to about 0.080-in. square, using reductions of 15 pct in area per pass. The 0.080-in.-square wire was cut into 6-in. lengths for the preparation of the alloys by the gaseous absorption and diffusion method. ADDITION OF OXYGEN, NITROGEN, AND HYDROGEN TO TITANIUM A modified Sieverts' absorption apparatus, shown in Fig 1, was used in

Jan 1, 1950

By JOHN D. SUMMER

THE Premium Price Plan for copper, lead, and represent, the approach of the Office of Price Administration to the urgent of wartime problem of securing increased output of nonferrous metals. Some of the problems encountered in too operation of the Plan and the considerations which led to it?s adopt it will here he reviewed. The Plan provides for extra payment by the Metals Reserve Co., to mine operators who exceed established quotas of production. Producers are thus directly, compensated for the higher costs of working ores that are not commercial at the ceiling price, although the metal obtained from these ores is directed into regular channels of distribution at the established prices for copper, lead, and zinc. Higher-cost metal is thus available to fabricators and to the government agencies at the regular ceiling price and the dual objective of increased production and table pries is achieved.

Jan 1, 1943