Search Documents

By Hsun Hu

NOT much data are available in the literature on textures in cross-rolled metal sheets. Among the body-centered-cubic metals, a few investigators have studied the preferred orientations developed in cross-rolled and in subsequently annealed molybdenum specimens.1-4 Semchyshen and Timmons5 onstructed complete pole figures for the cross-rolled and subsequently annealed arc-cast molybdenum. They used the conventional photographic method. Similar data on cross-rolled iron are still lacking. In view of the fundamental importance of iron as a basic metal for magnetic alloys and many industrial steels, the present investigation was undertaken in an attempt to understand more about its properties. The material selected for the present work was of high purity, and the textures were determined by the Geiger counter spectrometer technique, which permits the construction of quantitative pole figures. Experimental Procedure The material used for this investigation was NRC (National Research Corp.) high-purity, gas-free iron. The total gas content (N2 + O2 + H2) given was less than 0.026 pct, and the carbon content, less than 0.005 pct. Spectrographic analysis of a 2 in. cast ingot showed the percentage of metallic impurities as 0.0004 pct Cu, 0.0002 pct Mg, 0.001 pct Mn, 0.01 pct Ni, and 0.006 pct Si. A 1 in. thick slice was cut off from the 2 in. cast ingot. It was hot-forged at 850 °C to destroy most of the cast structure. Surface scale was removed by milling the forged piece to a size 2 in. long, 1½ in. wide, and ¾ in. thick. After normalizing at 915 °C for 15 min, the piece was alternately cold-rolled 40 pct and annealed at 750°C in hydrogen to a final thickness of 0.165 in., with a resulting uniform grain size of 0.1 mm.

Jan 1, 1958

By O. M. Schaus

REDUCED activity of mining, because of the business recession, had the effect of lowering working time, hence of reducing exposure to accidents, so it is probable that 1938 will be found to have had a lesser number (both fatal and nonfatal) though the accident rate may remain about the same as in 1936 and 1937. During periods of re-employment, such as occurred during 1936, 1937, and 1938, the new men entering the industry are less experienced and not as well trained in accident prevention as are the older, more experienced men and are frequently subject to more accidents. This situation should tend to correct itself as the new employees be- come better trained.

Jan 1, 1939

By Ralph H. Sweetser

BENEFICIATION of iron ores from the blast-furnace point of view means more than the usual enrichment of the iron contents by the removal of a large part of the clay, carbonic acid gas, silica, or moisture of the natural ore; it includes all these, but it also embraces several other mechanical .processes made , necessary by the exacting requirements of present-day blast-furnace practice. The increasing use of iron- bearing by-products, to as much as a third or more of the total ore burden, has introduced still another series of processes for improving the blast-furnace ore burden. As we look back over the past three decades of blast- furnace practice 'in. this country, we see that many of the blast-furnace troubles were directly due to lack of proper preparation of the iron ore burden,, and we realize that beneficiation in one form or another would have remedied the trouble. This was particularly true in the smelting of magnetic iron ores, where run-of- mine ore included such big lumps of 'magnetite along with rich fines that the furnace operations were greatly retarded and control of the furnace such as is usual today, was completely unknown.

Jan 1, 1930

By E. J. Eisenach, W. E. Jones

SAFETY and industrial hygiene have always been recognized as highly important in company policy, and the co-operative support of the company officials and entire plant personnel has contributed largely to the present success of the Company's program in this field. Growth has necessarily been slow, and dependent, at times, on trial and error but the program in its present form combines the regulations, working methods, and equipment that have proved their value under actual operating conditions. Every effort is made to keep the program on a practical basis. Continuous experimental work is carried on in conjunction with the health and safety program, with resultant periodic changes for improvement. As a proof of accomplishment, in 1945 the frequency and severity rates for accidents were the lowest in the history of the operation. A full-time safety engineer was employed in 1933 and an assistant safety engineer in 1936. During the following year a stenographer was employed in the office and a safety inspector was added for the mine. During the gradual expansion of operations that was climaxed by

Jan 1, 1946

By Edward Steidle

TWO years ago the Committee on Latin American Education Relations, Mineral Industries Education Division, started a study of mineral industries education in the Latin Americas. Information was obtainable only with great difficulty. Some information was available piecemeal but no complete resume had ever been assembled. Initial assistance was gained from the United States Office of Education and the Pan American Union. This, and first-hand knowledge of the writer, provided a list of colleges and universities which were believed to offer work lead. ing to a degree in one or more branches of the mineral industries. Detailed information could be obtained only by direct contact with each university through air mail service. Questionnaire letters were sent to officials of 34 colleges and universities. Twenty-one gracious replies were received. Fourteen of the colleges and universities concerned offer curricula in mining, five in metallurgy, three in petroleum, seven in geology, one in geographical engineering, one in topographical engineering, and one in geophysics. Two institutions offer advanced training in petroleum engineering. No institution offers any courses under the caption of ceramics or fuel technology.

Jan 1, 1945

By B. Silliman

THESE ores occur in the Laurentian rocks in the town of Clifton, St. Lawrence County, New York. The Clifton Mining Company have opened these magnetites upon their estate of 23,000 acres, on the waters of the Grasse River, an affluent of the St. Lawrence, which flows for about nine miles across the estate, exposing a section of the formation, and affording ample water-power at numerous points. In approaching this district from De Kalb Junction, upon the Watertown and Ogdensburg Railway, the observer passes from the zone of the specular ores, which abound to a great extent in Jefferson County, across a belt of non-metal-liferous limestones, continuing for some miles intermingled with metamorphic rocks, and gradually giving place to heavy beds of granitic and porphyritic gneiss, the weathered surfaces of which present a gray and rough appearance, from the washing out of the feldspar; leaving the quartz very prominent, and completely disguising the real character of the rock, which, when freshly broken, has a lively reddish appearance from the predominance of flesh-colored and red feldspar. Beds of fine-grained quartzite appear also intercalated in the granitic gneiss. These are the dominating rocks of the magnetite region, but the magnetite is always found, so far as the speaker's observation extended, associated with beds of calcite, carrying hornblende, black and green, biotite, and brown garnet interspersed with yellow and magnetic pyrites. The strike of these rocks is about northeast, and their dip about 40° to 45° southeast.

Jan 1, 1873

By W. L. Phillips

Nickel alloys containing approximately 0.5, 2.0, and 6.0 at. pct of Os, Pd, Ru, and Rh were Prepared by vacuum melting. Tension tests were carried out at 25°, 500°, 800°, and 1000°C; stress-rupture tests were carried out at 650° and 800°C. The room- and elevated-temperature tensile strength, as well as the stress-rupture life, increased for the same atomic percent in the order palladium, rhodium, ruthenium, osmium. The ductility decreased with increasing concentration or temperature for a given concentration. The results are discussed in terms of solid-solution theory. BOTH solid-solution strengthening and weakening have been observed in alloys. The simple rules which have been suggested to explain alloy strengthening are subject to several exceptions and deviations based on atom size and valency effects. The purpose of the present investigation was to extend the knowledge of the effect of solid-solution alloying on the mechanical properties of several Ni-Pt group metal alloys at room and elevated temperatures. The platinum group metals, osmium, ruthenium, rhodium, and palladium were chosen as the solute elements because of their different valencies and atom sizes. Nickel was chosen as the base material because of the large amount of previous literature available on nickel alloys. EXPERIMENTAL PROCEDURE Grade A Carbonyl nickel powder having the following composition: C, 0.07 pct; Fe, 0.013 pct; Mn, 0.0005 pct; Si, 0.016 pct; Mg, 0.0003 pct; S, 0.003 pct, was purchased from the International Nickel Co. The platinum-group metal powders were purchased from A. D. Mackay Co. The powders were weighed, cone-blended for 4 hr, and vacuum-melted into 1-in.-diam billets, approximately 2 in. long. The ingots were homogenized for 5 hr at 1800°F before being extruded into 1/4-in. rods at 2100°F. The alloy compositions are shown in Table I. Typical impurity values were not significantly different than that of the as-received nickel. All alloys were single phase. The lattice parameter of each alloy after the heat treatment described below is also included in Table I. Each alloy was annealed at 2200°F for 1 hr and air-quenched to comparable grain sizes (ASTM G.S. No. 4-5). The rods were then machined into test samples 0.160-in. diam and 0.750-in. gage length. Tension testing was carried out in an In-stron tension-testing machine at a strain rate of 0.02 in. per in. per min. An extensometer was used to determine the room-temperature yield stress. Stress-rupture testing was carried out in an Arc Weld stress-rupture unit. All testing was performed in air. EXPERIMENTAL RESULTS A) Room-Temperature Mechanical Properties. The 0.2 pct yield stress, ultimate tensile strength, and elongation for all alloys tested at room temperature are plotted as a function of atomic percent solute element in Fig. 1. The ultimate tensile strength for the same atomic percent increases in the order palladium, rhodium, ruthenium, osmium. The yield strength at low concentrations, -0.5 at. pct, increases in the order osmium, palladium, ruthenium, rhodium. At higher concentrations, 3.0 and 10.0 pct, the yield strength increases in the same order as the tensile strength. Both yield strength and tensile strength increase rapidly ini-

Jan 1, 1964

By P. Somasundaran, K. P. Ananthapadmanabhan

A knowledge of the role of effects and interactions of chemical species is important in developing an understanding of the behavior of mixed minerals and natural ores in beneficiation processes such as flotation and flocculation. In this study the role of such species was examined for the calcite-apatite system by conducting flotation of each mineral in various supernatants prepared by mixing with water. Supernatants of apatite and even that of calcite depressed the flotation of calcite markedly in the pH range of 5 to 13. Addition of Ca(NO3)2, K2C03, and K3P04 also produced definite effects under various pH conditions. Apatite flotation was also affected by the mineral supernatants and by carbonate and phosphate solutions. The results are analyzed in terms of the surfactant's solubility properties and the mineral's electrochemical and dissolution properties. While depression of calcite flotation by the dissolved species is found to be governed by depletion of oleate by bulk precipitation, the depression of apatite flotation is caused by the carbonate and phosphate species in the system. Turbidity measurements and a thermodynamic analysis of possible interactions in the system support these considerations. The effect of the supernatant of minerals on their own flotation suggests the important role of kinetics of various surface interactions in comparison to that of mineral dissolution.

Jan 1, 1985

W. M. CURSE, Mansfield, Ohio.-Outside of the commercial valu-ation of the material, for what purpose does this alloy-90 per cent. of copper, 6 ½ per cent. tin, 2 per cent. zinc, and 1 ½ per cent. Lead-seem to be eminently fitted? C. P. KARR.-So far as our tests go, it would be eminently fitted for steam valves and pistons, and for the work for which 88-10-2 bronze is generally used, although for very large castings it would not be superior to 88-8-4 bronze. P. E. MCKINNEY, * Washington, D. C.-Some time hack, clue to a desire to avoid some of the objectionable features of 88-10-2 bronze, particu-larly on heavy castings, also to save tin where possible, we took up the question of a substitute for 88-10-2 bronze, where red bronze was ordinarily specified. After trying most of the mixtures, we found that when using as low a tin content as is given in this proposed composi-

Jan 12, 1919

By Dozier Fircley

SOME nonmetallic minerals and their products, such as portland cement, common brick and hollow tile, sand, gravel, crushed rock, vitrified salt-glaze clay pipe, and the like, are a necessity in every community. They are mineral in nature but the establishment of plants for their production is usually a local and elementary problem. Yet it is probable that an economic study of the problem in every locality will show that such nonmetallic mineral commodities are not always obtained in the most economical way, or in the best quality. Other nonmetallic minerals are of such value that they may be shipped for long distances and sold in sufficient quantities to establish prosperous commercial ventures. Among these are phosphates, barium compounds, borates, nitrogen compounds, magnesium compounds, sulfur, asbestos, and potash. Success in marketing such products depends on quality, production cost, transportation, and similar conditions.

Jan 1, 1932

By Jerome Strauss

IN his review of developments in 1943, Gilbert Seil, Chairman of this Committee on Reduction of the Ferroalloy Ores, tabulated the consumption of the alloying metals in relation to the steel production of that year. In the year just closed the approximate tonnage was of the same order, differing only to a minor degree or suffering some correction with more precise figuses available, as indicated in the following estimates: Consumption Metals in Tons Steel 92,000,000* Manganese 700,000 Silicon 200,000 Chromium 200,000 Nickel 75,000 Molybdenum 20,000 Tungsten 8,000 Vanadium 1,700 Titanium 1.600 Boron 10 `Production figure. The technologic studies instituted during 1942 and carried forward with such great vigor during 1943 continued into 1944 although in some instances were brought to a close either by completion of the specific development

Jan 1, 1945

By B. C. Allen

Grain-boundary gvoocing was studied irz chronziu?n. molybdenum, tungsten, and the solid-solution alloys, Cr-35Re. Mo-33Re, and W-25Re at 0.6 to 0.9 of the absolute liquidus temperature under an inevt atmosphere , foveign nzetal zlapor, and liquid metal. The controlling mechanism of matter transport was deduced frolr groove size and shape. kinetics of growth, and cotnparisoz with theoretical relatiotzships derived by Mullins. Grooves in chowzizon formed prittzarily by volume diffusion tkrongk kelium or argon at 1 atm pressure and by e1)apovation-condensatiotz in a static vacuum. Groozles in the other nzetals and alloys forrned priniarily by sirface diffusion, the coefficients of which were calculated. Carbon was found to decrease the acti7:ation energy for surface diffusion on molybdenun. Sitrface diffusizities weve sinzilav for iWo-0.0ZC and Mo-33Re. The presence of about 1 -?nm pressure of silver or tin vapor did not affect the neckanis)n of grooz;e formation. In liquid titz or silz:er, pain bolindary gvooves formed by zolume diffusion in the liquid. BASED on theories of ullins," the mechanisms of grain-boundary grooving have been determined for low-melting metals such as copper in an inert atmospheres or in liquid lead.4 The purpose of this investigation was to study grain-boundary grooving in the refractory Group VI-A metals, chromium, molybdenum, and tungsten, and the bcc solid-solution alloys, r-35e, 0-33e,= and -25e,' at 0.6 to 0.9 of included to see whether Mullins' theories were applicable to them as well. EXPERIMENTAL WORK The materials chromium, molybdenum, tungsten, Cr-35Re, Mo-33Re, and W-25Re were in the form of 0.050-cm-thick sheet assaying 99.98 pct or better. The nominal carbon level was generally 30 ppm. The oxygen + nitrogen + hydrogen content was -50 ppm. Mo-33Re and W-25Re were prepared by powder-metallurgy methods and supplied by Chase Brass and Copper Co. The remaining materials were arc-cast. Chromium and Cr-35Re were prepared at Battelle by arc melting, extruding, swaging, and rolling. Mo-0.003C was supplied by Climax Molybdenum Co., and Mo-0.02C and tungsten by Universal Cyclops Corp. As a source of liquid metals, tin and silver granules assaying 99.98 pct were used. Spectrographic analyses indicated the presence of -100 ppm each of iron and silicon. Vacuum melting reduced the combined gas content to c5 ppm (2.60,, 0.9N2, 0.4H2 in tin and l.602, 0.7N2, and c0.04H2 in silver). Specimens were prepared for grain-boundary grooving. Coupons 0.5 by 1.5 cm with a small hole in one end, or substrates 1.5 by 1.5 cm, were cut from sheet. The specimens were annealed in containers of the same material to provide a vapor-solid equilibrium as well as to protect them from gaseous impurities. Outgassing was done at 2 x 10"5 mm for 15 to 30 min at 1150°C for chromium and Cr-35Re, 1750°C for molybdenum and Mo-33Re, and 2600°C for tungsten and W-25Re. Then recrystallization to a stable grain size of about 0.5 mm was accomplished by annealing at least 1 hr at 1600°C for chromium, 1800°C for Cr-35Re, 2350°C for molybdenum, and 2300°C for Mo-33Re in a rhenium-element resistance furnace under 1 atm of static argon or helium. The atmosphere was gettered by tantalum radiation shielding. Tungsten and

Jan 1, 1967

By John W. Langley

In the summer of 1888 it was the fortune of the writer to present the subject of the desirability of establishing a set of samples of steel, which should be analyzed with extreme care, in order that they might become standards to which scientific and commercial analyses of iron and steel could be subsequently referred; also, that greater uniformity in the results of analyses might be brought about, since these standards would bear towards analytical methods somewhat the position which the original units of weight and length, the gramme and meter, or the pound and yard, preserved in Paris, London, and Washington, do to the mechanical arts. The plan met with hearty co-operation, with the result that com mittees were appointed in Sweden, Germany, France, England, and America, to receive the material and to see that the necessary au alyses were executed. In England, the British Association for the Advancement of Science appointed a committee, which subsequently published a plan

Jan 1, 1891

By J. E. Flinn, S. A. Duran

The steady-state creep behavior of poly crystalline cad mi inn was studied over a temperature range of (1.56 to 0.94 Tm. Two distinct mechanisms were found to occur over this temperature range. They were described by: where and represerqt the minimum strain rates corresponding to the low- and high-temperature regions, respectirely. The two regions of constant acti11ation energy were connected by a transition region where the strain rate was controlled by both mechanisms acting in parallel. At temperatures below a transition temperature of about 0.7 Tm the agreement between the activation energy value for creep and that for self-diffiision suggests a rate-controlling mechanism of dislocation climb. For cadwzium, steady-state creep at temperatures above 0. 7 Tm appears to be controlled by another mechanism, perhaps involving the behavior of dislocation jogs. FRENKEL et al.1 studied the high-temperature creep of polycrystalline cadmium and reported an activation energy of 21 kcal per mole for the 0.5 Tm < T < 0.8 Tm range. Based on observations of creep rate at only two temperatures, a value of 22.1 kcal per mole was determined by Medbury. These two investigations were for the purpose of showing agreement between the activation energy for creep and that for self-diffusion, reported3 as 18.2 and 19.1 kcal per mole, respectively, for diffusion parallel and perpendicular to the hexagonal axis. Gilman4 investigated prismatic glide in single crystals of cadmium over a higher-temperature range of 0.72 to 0.93 Tm, and found an activation energy of 29 kcal per mole. He also reported5 an activation energy higher than that of self-diffusion for prismatic glide in zinc single crystals deformed at temperatures near the melting point. This value was in good agreement with those found for an equivalent temperature range by Flinn and Munson6 and by Tegart and sherby7 for polycrystalline zinc. These two independent studies also disclosed at lower temperatures another value of activation energy near that for self-diffusion. It would be expected from the creep results on zinc and single-crystal cadmium that creep studies on polycrystalline cadmium, extended to temperatures near the melting point, might yield an activation-energy value higher than the 22 kcal per mole value found in earlier studies. The purpose of this paper is to report the steady-creep behavior of polycrystalline cadmium over a temperature range of approximately 0.5 to 0.9 Tm EXPERIMENTAL METHOD The cadmium used in this study was obtained in the form of as-cast rods, 0.5 in. diam, through the courtesy of the Bunker Hill Mining Co. The material was of 99.995 pct purity, as determined by spectro-chemical analysis. The creep specimens, which were 0.250 in. diam by 0.400 in. long and annealed at 300°C for 45 min to produce a stable average grain diameter 0.25 mm, were tested in compression using an apparatus similar to that described by Sherby.8 The specimen temperature was controlled to within ±0.5°C with the help of appropriate constant-temperature baths. The applied stress was maintained within 1.0 pct of the desired value by the additions of lead shot at fixed strain increments. No barreling was observed over the strains encountered during testing. Isothermal creep tests9 were used in the study with only a few differential temperature tests10 run for comparison purposes. Steady-state creep data were obtained over a temperature range of 60 to 287°C (0.56 to 0.94 Tm) at five stress levels ranging from 28.1 to 140.6 kg per sq cm. RESULTS The minimum or steady-state creep rate may be described by an equation of the following form:" where i is the minimum strain rate, S is the structure factor, F is a stress function, Qc is the energy of activation, T is the absolute temperature, and R is the gas constant. The minimum strain rates obtained in this study for cadmium were recorded on a semilogarithm plot as a function of the reciprocal absolute temperatures for the various stress levels, as shown in Fig. 1. This figure shows a characteristic transitional behavior" with a parallel interaction of two mechanisms. It is obvious that the activation energies corresponding to the individual processes are insensitive to stress because the curves are parallel. The discrete activation-energies values for the low- and high-temperature regions for the various stress levels are reported in Table I, and were determined by the least-mean-square method. For the low-temperature region, an activation energy of 20.7 ± 0.6 kcal per mole was obtained, and for the

Jan 1, 1967

By B. Silliman

THESE ores occur in the Laurentian rocks in the town of Clifton, St. Lawrence County, New York. The Clifton Mining Company have opened these magnetites upon their estate of 23,000 acres, on the waters of the Grasse River, an affluent of the St. Lawrence, which flows for about nine milt",3 across the estate, exposing a section of the formation, and affording ample water-power at numerous points. In approaching this district from De Kalb Junction, upon the Watertown and Ogdensburg Railway, the observer passes from the zone of the specular ores, which abound to a great extent in Jefferson County, across a belt of non-metal-liferous limestones, continuing for some miles intermingled with metamorphic rocks, and gradually giving place to heavy beds of granitic and porphyritic gneiss, the weathered surfaces of which present a gray and rough appearance, from the washing out of the feldspar; leaving the quartz very prominent, and completely disguising the real character of the rock, which, when freshly broken, has a lively reddish appearance from the predominance of flesh-colored and red feldspar. Beds of fine-grained quartzite appear also intercalated in the granitic gneiss. These are the dominating rocks of the magnetite region, but the magnetite is always found, so far as the speaker&apos;s observation extended, associated with beds of calcite, carrying hornblende, black and green, biotite, and brown garnet interspersed with yellow and magnetic pyrites. The strike of these rocks is about northeast, and their dip about 40&apos; to 45&apos; southeast

By Paul A. Farrar, Harold Margolin

The system Ti-Cr has been re investigated From 40 to 100 pct Cr. The high-temperature modification of TiCr, was found to exist in the temperature range from 1365 where it terminates in the eutectoid reaction TiCr,(TI)* — HE chromium-rich region of the Ti-Cr system was investigated by Vogel and Wenderott,&apos; Mc Quillan,&apos; Van Thyne et dl.,&apos; and Cuff Duwez and Taylor determined the crystal structure of the low-temeperature modification of TiCr, to be fcc a = 6.943A and Levinger&apos; discovered the existence of a second (high-temperature) modification of TiCr, and determited its crystal structure to be hexagonal a = 4.932A, c/a = 1.617i. No information was obtained as to the temperature range over which each modification of TiCr? existed; therefore the present investigation was initiated. I) Experimental Techniques Alloys employed for the delination of this system were prepared from iodide titanium and high-purity chromium. The purity of these materials is as follows: Iodide titanium: purity 99.99 pct; major impurities—carbon 0.0001 pct; oxygen 0 to 0.002 pct; nitrogen 0 to 0.002 pct; silicon 0 to 0.005 pct; manganese 0.001 pct; copper 0.001 pct (Foote Mineral Co., Lot 609-29). Chromium #1: metallic purity 99.997 min.; interstitial content—oxygen 0.27 to 0.46 pct; hydrogen 0.028 to 0.038 pct; nitrogen 0.0002 pct (Ave-quipo Inc.). Chromium #2: purity 99.9 pct; major impurities—carbon 0.01 pct; oxygen 0.013 pct; nitrogen 0.02 pct; silicon 0.01 pct; sulfur 0.03 pct; iron 0.01 pct (Fulmer Research Institute Ltd.). A total of sixteen alloys of thirteen different compositions was prepared in the range from 40 to 95&apos; *All percentages are given in weight percent. pct Cr. The compositions of the alloys prepared were as follows: Ti-40, 45, 50, 60, 62, 64, 66, 68, 70, 80, 85, 90, and 95 pct Cr. Two buttons were prepared of the 66, 90, and 95 pct Cr alloys. The 40 pct Cr and one of the 66 pct Cr alloys were prepared from the chromium # 2. All the other alloys were prepared from chromium #1. The alloys were arc-melted as 25-g buttons in a copper-hearth glass-walled furnace7 under an inert atmosphere of high-purity helium. The alloys were sintered at 250 amp and melted twice at 350 amp for 30 sec with the buttons being turned over between melts. Weight losses during melting were determined and in the range 45 to 68 pct Cr they were found, in all cases, to be less than 1.25 pct of the total alloy weight. A number of the high-chromium alloys shattered during cooling from either the first or second melt, which made the weight loss considerably larger than usual. The 70 and 80 pct alloys lost approximately 5.7 pct of their total weight, the 85 pct alloys 1.5 pct, the 90 pct alloy 2 pct, and the 95 pct alloy 3 pct. However, it is felt that the actual composition of the alloys in this region is probably within approximately 1 pct of the intended composition, as a large portion of the material lost was that due to shattering after melting. Nominal compositions were therefore used in plotting data and referring to the alloys. The alloys were cut into specimens, wrapped in molybdenum sheet, and encapsuled in argon-filled quartz or Vycor tubes for heat treatment. The heat-treatment times and temperatures are given in Table I. The specimens were quenched in iced brine (I.B.Q.) following heat treatment. The standard techniques of grinding, polishing., and etching were used in preparing the specimens for metallo-graphic examination. For alloys below 68 pct Cr

Jan 1, 1963

By D. F. Coolbaugh

Successful mine exploration requires sound planning and modern exploration techniques, but it also requires perseverance and the right timing. The La Caridad mineral area has been known for over 70 years, but as with many mines, it was not "discovered" until viewed under new economic conditions and exploration philosophies. Present exploration of the La Caridad area began in 1964 and was carried out under a joint Mexican Government-United Nations Project. Detailed exploration was begun by Asarco Mexicana S.A. in late 1968. The geology of the La Caridad deposits conforms, generally, to the "porphyry copper" deposits of Arizona. However, breccias and pegmatites play a very important part in the emplacement of mineralization.

Jan 1, 1972

By M. Tanaka, S. Kita, Y. Jinnouchi, Y. Sawada

This paper generalizes the results of the recent theoretical and experimental investigations on the air-pulsated jigs in Japan. The pulsating mechanism is analyzed as a special vibratory system, and the jigging mechanism as a mass system subjected to the law of hindered settling. The results of investigations on the following items are reviewed: dynamics of the pulsating mechanism; pulsation in a practical TACUB jig development of a new type of air valve; uniform pulsation in a large Baum jig; motion and mobility of bed particles; separating speed in hindered conditions; and standard deviation in practical jigs.

Jan 1, 1985

By J. P. Hammond, C. J. McHargue

THERE have been no publications on the wire texture, on the cold-rolled sheet texture, nor on the recrystallized sheet texture of vanadium. Since it has a body-centered cubic structure, it would be expected to show strongly preferred orientations such as are found in iron&apos; and molybdenum.&apos; The wire textures of body-centered cubic iron,3 tungsten," molybdenum,5 antalum,6 iobium,6 and brass6 have been found to have [110] directions lying parallel to the wire axis. Wires of iron,&apos; containing 1.95 pct V or 1.95 pct Si,7 and steel8 retain their texture upon recrystallization. Molybdenum9 and tungsttln&apos; wires retain their texture after recrystallization at low temperatures. A [loo] recrystallization texture has been reported for mo1ybdenum9 and for a Fe-Ni alloy (53 atomic pct Ni).10 The cold-rolled sheet texture for iron,&apos; mild steel," and molybdenum chiefly one in which the [110] directions lie parallel to the rolling direction and the (100) planes lie parallel to the rolling plane with a deviation from this position chiefly about the rolling direction as an axis. This paper presents the cold-rolled and the re-crystallized wire textures, and the cold-rolled and the recrystallized sheet textures for vanadium. The results show that the textures in vanadium are not significantly different from those reported for other body-centered cubic metals. The vanadium used in this investigation was the so-called "ductile" vanadium which has a nominal composition within the following limits:12 0, 0.05 to 0.12 pct; H, 0.001 to 0.004; N, 0.02 to 0.04; C, 0.03 to 0.07; and V, 99.8 to 99.9. The wires were formed by rolling annealed rods of 0.280 in. diam to 0.028 in., a reduction in diameter of 90 pct. The wires were then electrolytically etched to 0.005 in. diam and used as such for specimens. Annealed sheet was reduced 95 pct in thickness from 0.100 to 0.005 in. with a two-high, 4-in. diam mill using reductions no greater than 10 pct per pass. In order to avoid temperature effects, the sheet was allowed to cool between passes. X-ray specimens were made in the form of posts from the sheet. The sheet was mounted in a fixture and the edges were polished using metallographic technique. Each edge was alternately polished and etched during the last stages in order that all worked material would be removed. These post specimens were approximately square in cross-section. The specimens to be recrystallized were wrapped in tantalum foil, sealed in evacuated quartz tubes, and annealed at 1600°F. The X-ray data were obtained from transmission shots made with a 0.030 in. pinhole camera, and molybdenum radiation with a zirconium filter inserted between the specimen and film. The grain size was sufficiently small in both the cold-worked and recrystallized material to give satisfactory results with the specimens stationary. In order for the wire texture to be determined, transmission X-ray patterns were taken with the

Jan 1, 1953

By O. P. Arora, M. Metzger, G. R. Ramagopal

Single-phase aluminum containing 0.0001 to 0.06 pct Cu was studied in strong acid, mainly through observations of hydrogen evolution. The strong influence of copper was exerted almost entirely through the imposition after a certain delay time of an auto-catalytic localized-corrosiott reaction. Additions of cupric ion to the acid produced lower accelerations. The significance of the quantity and distribution of copper was discussed, and the implications for intergranular corrosion and neutral chloride pitting were indicated. AN investigation of intergranular corrosion in single-phase high purity aluminum exposed to hydrochloric acid indicated the copper content of the metal to have an influence on corrosion at lower levels than previously suspected.&apos; The work reported here was a closer examination of the action of copper but dealt with general corrosion to gain the advantage of having a continuous measure of corrosion through the volume of hydrogen evolved, the reduction of hydrogen ion to hydrogen gas being the principal or only cathode reaction in strong hydrochloric acid. Previous work on the hydrochloric acid corrosion of aluminum was sometimes insufficiently structure-conscious and the need for care in evaluating it arises from the low solubility of the iron impurity,&apos; and of some alloying elements, and the known or possible presence in many of the compositions studied of second phases leading to greatly increased corrosion rates.3 These increases are attributed to the presence of low hydrogen-overvoltage cathodes provided by the second phase.3&apos;4 For the present single-phase work, a few studies which used high-purity base material and small copper additions5-&apos; provide the essential information most unambiguously. The corrosion rate was shown to be increased markedly by the introduction into the acid of small quantities of the ions of copper (and of certain other metals) which cement on the aluminum and provide cathodes of low overvoltage.5 When there was sufficient copper in the aluminum, the same result was produced during the course of corrosion leading to a rate which increased with time as the reaction was stimulated by one of its products (autocatalytic reaction). In 2N (7pct) HC1, an accelerating rate was observed at 0.1 pct Cu but not at 0.01 pct.5,7 The present work dealt with corrosion rate and morphology and their correlation with the quantity and distribution of copper catalyst for copper contents from 0.0001 to 0.06 pct. PROCEDURE A lot of high-purity aluminum containing 0.0021 pct Cu, 0.001 pct Fe and 0.003 pct Si (Alloy A) was alloyed with copper to yield aluminum containing 0.014 pct Cu (B) and 0.06 pct Cu (C). Later it was found necessary to include the lower copper Alloy K which contained 0.0001 pct Cu, 0.0004 pct Fe and 0.0004 pct Si. The upper limit for any other element can be confidently estimated as 0.0005 pct. No element other than copper appears to be present in quantities sufficient to have an effect on general corrosion as great as the observed effect of the copper in A, B, and C. The only other heavy metal detected by spectrographic examination was silver (< 0.0001 pct). The acid was made up from a selected lot of 37 1/2 pct CP hydrochloric acid containing 0.1 ppm heavy metals (mainly Pb), 0.05 ppm Fe, and < 0.008 ppm As and from water distilled from 1 megohm-cm demineralized water and believed to have contained negligible quantities of heavy metals influencing corrosion. Acid strength was adjusted to within 0.05 pct HCl of the stated value by using precision specific gravity measurements. Test blanks 10 by 41 mm were sheared from 1.65-mm cold-rolled sheet. Edges were finished by filing. The blanks were annealed in air at 645°C for 24 hr in alundum boats and rapidly water quenched. The anneal is thought to have produced a substantially homogeneous solid solution—for iron, copper, or silicon, for example, the annealing temperature was 200°C or more above the solvus-and the quench is considered to have preserved the high-temperature structure except for the condensation of lattice vacancies into dislocation loops.&apos; The 0.06 pct Cu alloy did not appear unstable in respect to slow precipitation reactions at room temperature since two pairs of tests failed to show significant differences between specimens heat treated 3 1/2 years earlier and specimens heat treated 1 or 2 days before.

Jan 1, 1962