Search Documents

By J. C. Trantham, J. W. Marx

From 1955 to 1958 the Phillips Petroleum Co. conducted a series of small scale counterflow combustion field tests in a tar sand about 60-ft deep and 6 to 12-ft thick near Bellamy, Mo. A total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern, were employed. Electric heaters, gas burners and wellbore fuel packs were tested as counterflow ignition devices. Direct drive ignition followed by reversal to counterflow operation was not possible in this case because of formation plugging by the semi-solid tar during the direct drive phase. Sustained counterflow burning was achieved with wellbore fuel packs under conirolled conditions which permitted close correlation of fire front velocity, air velocity, air-oil ratios and yields for a wide variation in process parameters. The tar in place was about 10' APl with a reservoir viscosity greater than 500,000 cp. The composite oil prodlcct was 26' API with a viscosity in the range of 5 to 15 cp. Vertical sweep efficiency in the line drive pattern was essentially 100 per cent, with no evidence of gravity segregation. Original tar in place ranged between 800 and 1,000 bbllacre-ft, specific rock permeability averaged about 800 md before burning and effective air pemeability with residual oil and water in place (at the time of ignition) averaged 250 md. The volume of oil recovered during stabilized line drive counterflow burning represented about 67 per cent of the volume of tar originally in place in the burned out zones. A minimum was found when air-oil ratios were plotted against formation air velocities, and a limiting air velocity existed below which the counterflow fire front reversed and burned back over its own trajectory, using the residual coke left behind. INTRODUCTION Early in 1955 the Phillips Petroleum Co. began preparations to field test counterflow underground combustion as a method for producing oil from high viscosity hydrocarbon deposits, such as bituminous (tar) sands. At that time all published information on the use of underground burning io increase oil recovery was based on the direct drive process, in which the fire front moved through the formatim in the same direction as the injected air stream. Such direct burning is not applicable to many heavy oil sands or to most tar sands because the heat-thinned native hydrocarbon congeals in the cold rock ahead of the fire front forming a gas permeability block which smothers the combustion. Laboratory experiments first demonstrated that this permeability blocking would not occur if the fire front and the air stream moved in opposite directions. In this counterflow (reverse) burning process the heated heavy oil or tar is driven back through the combustion zone. Here thermal cracking produces relatively light hydrocarbon products which pass through the heated rock behind the fire front (largely in the vapor phase) and are incapable of causing a gas permeability block.' Exploratory wring revealed that consolidated bituminous sandstones with a combination of tar saturation, permeability, thickness and depth favorable for experimental field testing existed at several points in western Missouri. By the fall of 1955, a test site for determining technical feasibility of the counterflow process under field conditions had been selected near Bellamy, Vernon County, Mo. — about fifty miles north of Joplin. The pay zone was too thin and too shallow to constitute a commercial prospect, but these same factors permitted controlled experimental operation with a small compressor installation and with a large number of monitor wells. These were needed for adequate observation of the underground phenomena at reasonable cost. RESERVOIR CHARACTERISTICS The reservoir chosen for the experimental field tests was a 124 thick section of tar sand extending from 49 to 61 ft subsurface, with shale and siltstone laminations sealing the top and bottom. This section was part of a larger 30-ft thick tar sand deposit which extended both above and below the test zone. Core analyses showed that the 12-ft sand was effectively subdivided into two approximately equal sections, with the lower zone being consistently more permeable than the upper zone. The most significant laboratory core data are summarized in Table 1. The line drive test which is the principal subject of this report utilized only the lower 6-ft thick zone, with the upper zone regarded as part of the 55-ft overburden. WELL PATTERNS The over-all field test program involved a total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern. In some of the tests the full 12-ft zone was employed; in other cases only the more perme-

Jan 1, 1967

By Wayne A. Greenwalt

A method that determines venture participation when the decision maker's level of risk aversion varies according to venture profitability and risk investment is presented. The decision maker's fundamental aversion to risk is established by the selection of a desired working interest for a venture that anticipates only a discounted payout.

Jan 1, 1982

By J. E. Lawver, J. D. Raulerson, Charles C. Cook

The agriculture industry has made great strides during the past decade to increase agriculture yields through increased use of fertilizers. Increased use of fertilizers may prevent, or at least delay, mass starvation due to the alarming increase in world population. Phosphate was added to soil as a plant nutrient in the form of calcined bones at least 2000 years ago (Anon., 1964), and man has used phosphate minerals as a source of fertilization in one form or another for at least 100 years. During 1977 the world produced about 116 Mt of phosphate rock, with about 86% used for fertilizers and another 4% for animal feed supplements. More than three-fourths of the total production comes from the United States, Morocco, and the Soviet Union. From a mineral beneficiation point of view, the major sources of phosphate rock and the methods of beneficiation can be classified as follows: marine deposits not containing appreciable carbonate minerals, marine deposits requiring a francolite carbonate mineral separation, igneous deposits not containing appreciable carbonate minerals, and igneous deposits requiring apatite carbonate mineral separation. [ ] Guano, mostly from Chile and Peru, accounts for 0.1% of the total world production, and the calcium phosphates from Ocean, Nauru, and Christmas Islands and the aluminum and iron phosphates from Brazil and Aruba account for less than 4% of the world production and are thus not considered in this classification (Lawver, et al.). At present, marine phosphorite deposits account for about 75% of the world's production; the igneous deposits account for 20%. The igneous deposits low in carbonate minerals are easily concentrated by crushing, grinding, and apatite flotation. The most important igneous deposits are those of the Kola Peninsula, USSR (Woodrooffe, 1972). The igneous deposits high in carbonate materials are of corn appreciably more difficult to beneficiate, but they have been concentrated by froth flotation for a number of years. An interesting but rather complicated flowsheet of this type is at Phalabonva, in the Republic of South Africa (Lovell, 1976). The Phalaborwa deposit is an igneous complex of pyroxenite with a central core of carbonatite surrounded by a serpentine- magnetite-apatite rock called phoscorite. The phoscorite containing about 10% P2O5, 35% magnetite, and 35% calcium magnesium carbonate is currently being processed. The process involves comminuting the material for fiberation and subjecting it to a copper float using a potassium amyl xanthate as collector and triethoxybutane as a frother followed by a magnetic separation of the tailings to produce a feed for phosphate flotation. This process produces a phosphate concentrate containing greater than 36% P2O5 at a P2O5 recovery ranging from 75 to 80%. Considerable success has been claimed for recovering apatite from carbonate-bearing ores at the Jacupiranga Mine of Serrana S/A (Silva and Andery, 1972). The carbonatite currently being mined contains an average of only 5% P205 and is concentrated using a unique flotation process (Andery, 1968) to yield 96% P205 concentrates. The ore contains about 12% apatite, 5% magnetite, 80% calcite plus dolomite, and minor amounts of phlogopite, olivine, zircon, ilmenite, and pyrochlore. Feed preparation consists of crushing to -31.75 mm (-1 M in.), rod milling in closed circuit with hydrocyclones to about 92% (-50 mesh), and two-stage cyclone desliming of the -50 mesh sands at 20 m. Weight recovery in the deslimed feed is normally 85 to 88% and the corresponding P2O5 recovery is usually about 90%. The deslimed feed is conditioned at 60 to 70% solids for 15 min at pH = 8-10 with 0.6 kg/t of causticized starch for iron oxide and calcite-dolomite depression. The conditioned slurry is diluted to 20 to 30% solids, about 0.2 kg/t of fatty acid or soap collector is added to the conditioner discharge, and the reagentized ore is subjected to rougher-scavenger flotation with additional fatty acid added to the scavenger float. The scavenger concentrate is returned to rougher circuit distributor, and the rougher concentrate froth is subjected to two stages of cleaner flotation to yield a final apatite concentrate analyzing 36 to 38% P205. Flotation recovery of P205 is, in general, above 90% when treating fresh carbonatite. The high-carbonate flotation tails normally analyze 1 % P2O5 or less and are suitable for portland cement production. The marine deposits. Types 1 and 2 of central Florida are representative of enormous reserves of phosphate rock that will undoubtedly account for much of the world's production in the near future. Until very recently the sedimentary deposits high in carbonate minerals (Type 2) have not been considered reserves due to the difficulty in making a francolite-carbonate separation. Although no commercial plant has yet been built to beneficiate Type 2 ore, laboratory and pilot plant data indicate the process is viable. If so, the reserves of Florida and similar deposits throughout the world will be substantially increased. A discussion of the beneficiation of these two types of sedimentary deposits and the relation of the resulting concentrates to the fertilizer industry of the United States is the subject of this paper.

Jan 1, 1981

By James Hance

INTRODUCTION SEVERAL years ago the writer was connected with the Mint and Assay Service of the Federal Government as Assistant Assayer at the-Salt Lake Assay Office. At that time cyanide bars formed approximately half of the bullion purchased by that office. Disagreement in valuation between the producer and the office was not infrequent and to a lesser extent between the Assay Office and the Mint, this latter issue being soon obviated, however, by adopting uniform methods of sampling the bars. A nice problem seemed to offer itself for research and the writer began a series of experiments which were soon terminated, however, by his going into other work, and which he regrets have not since been completed. The results attained may suggest lines of approach to this problem and are, therefore, offered in this article. Frederick P. Dewey, Assayer of the Mint Service, U. S. Treasury, has had abundant opportunity to study this phase of metallurgy, and has published several articles relative thereto.1 In the last article cited Dewey quotes analyses of cyanide bullion similar in content to that with which the writer worked, and which show some of the variations met with. In the discussion of these papers,2 comparison has been made in terms of copper bullion, but to the writer this seems of questionable value. Copper bullion may resemble silver bullion, but its similarity to, gold bullion with little or no silver content is another thing. The freezing-point diagram of Roozeboom, reproduced on page 881 of the discussion cited, is for the gold-silver series as stated. The original problem under discussion, however, is not this alloy but gold with base metals other than copper. As for the statement that the corners are the worst places or

Jan 2, 1916

By John S. Alexander

By E. C. Burke, W. R. Hibbard

Plastic deformation in magnesium single crystals was studied by tensile tests at room temperature utilizing an improved preparation and testing technique. Consistent critical resolved shear stress values for basal slip were obtained. The advent of pyramidal slip at room temperature was rationalized upon the basis of grip constraints. A bend-twinning hypothesis was advanced as an explanation of mechanical twinning which occurs as a complex stress-relief mechanism. INVESTIGATIONS of the plastic deformation of magnesium have been limited to the determination of the fundamental kinetics which may be summarized as follows: 1—Twinning on the {102).l 2— Slip on the (001) plane in the [loo] direction at room temperature.' 3—Slip on the {101) or {102) plane in the [loo] direction above 225°C." 4—Critical resolved shear stresses for basal slip in tension at room temperature of 83 g per sq mm with a variation from 57 to 127 g per sq mm." Bakarian' studied the compression of thin wafers of magnesium single crystals and classified the components of the deformation mechanisms as follows: 1—The Basal field: (001) at an angle of less than 20" to the compression surface. Fracture along {101} or slip on (001) followed by {101} fracture. 2—The prism field: (001) at an angle greater than 60" to the compression surface. Twinning on the {102) generally occurring during the early stages of loading, basal slip in the areas of original orientation and (001) slip within twins. 3—The central field: (001) at angles greater than 20" but less than 60" to the compression surface. Slip on the (001). 4—The critical resolved shearing stress for {101} slip above 225°C was 400 g per sq mm. Observations of mechanical twins in hexagonal close-packed metals have been summarized by numerous investigatorsb-' emphasizing a lateral or rotational atomic adjustment, in addition to the pure twinning shear, and the importance of reorienting the basal plane to a position more favorable for continued slip, rather than the resulting small dimensional changes. Criterion for the operative twinning planes has not been clearly established. Schmid and Boas hurmised that an energy condition related to the atom movements is the determining factor. MillerQ bserved that twinning stresses in zinc crystals decreased as the amount of prior deformation increased. Preparation of Specimens Magnesium single crystals % in. in diam x 8 in. long were grown from the melt under an argon atmosphere in a gradient furnace similar to that described by Jillson." Magnesium containing 0.018

Jan 1, 1953

Jan 1, 1904

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

DEFORMATION lines, also called etch markings or strain markings, are noneffaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries.1 Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrette to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation required for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted deformation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson' observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brick9 noted that deformation lines in 70-30 brass apparently associated with {111} planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards11 reported that in copper cold rolled less than about 50 pct few strain markings were apparent but for higher. reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass

Jan 1, 1948

By Bradley Stoughton

As a part of the systematic study of the alloys of iron under the auspices of the Engineering Foundation, and preliminary to the commencement of comprehensive work on this larger subject, the authors have undertaken an investigation of the available literature dealing: with the alloys of iron and silicon. The purpose is to collect all the data in English and foreign languages and present them in two mono-graphs, one of a more scientific and the second of a more industrially useful nature. Of course, a great deal of information upon the constitution of the iron-silicon alloys was found specificially upon the changes of phase in the equilibrium diagram and the different phases present, such as solid solution, chemical compounds (iron silicides), etc. While no extended research was contemplated in the particular study undertaken, nevertheless the data collected proved to be so contradictory in many respects that a simple study of some of the outstanding problems involved in the constitution and equilibrium diagram was undertaken Because research was not a primary object of the work, and also because of the extreme industrial importance of the silicon alloys between 0.80 and 14 per cent. silicon, and finally because of the unsatisfactory state of knowledge existing as to these alloys, the experimental investigation was limited entirely to alloys with less than 10 per cent. silicon.

Jan 1, 1930

By L. S. Panyity

The inception of this paper may be traced directly to the various discussions of another paper by the writer1 wherein certain indefinite beliefs and opinions were emphasized as to the relative importance of total sand porosity and the actual size of the openings between the grains. Since publication of that paper it has been possible to study various methods of sand analyses and results that have been obtained under different conditions and actual operations in the field. The purpose of this paper is to indicate the value of screen analysis, especially in areas where repressuring by means of water-flood, air or gas is being used in the partly depleted fields. Sand samples have been analyzed for porosity, saturation and grain size. They are mainly from the Bradford water-flood area, where a great reliance has been put upon such analyses, and where many data are available, A few sand studies are included from fields other than the water-flood area, in order to indicate the possibilities of screen analysis in any field. Examples of various conditions are given in Figs. 1 to 7, which show the porosity, saturation and grain-size analyses of submitted cores or drill cuttings. The generally accepted methods of delineating such sand studies on cross-section paper, known as "core charts" has been employed; with the exception that a method of representing grain size has been evolved which is believed to be the best adapted for this purpose. It differs from the block diagrams generally used, in the employment of a linear section. Percentage of grain-size is represented by the subdivision of a given distance, where the total length represents the whole sample of rock chunk, while the subdivisions indicate the percentages of grains of the different sizes that will pass through the various sieves, through which the samples of crushed sand are sorted to determine the size and amount of the components that make up the aggregate. Thus, on Fig. 1, under the heading of Grain Size, the first samples are composed of grains of the following sizes: 16 per cent. through 120-mesh sieve; 33 per cent. through 150-mesh; 25 per cent. through 180-mesh; 26 per cent, through 200 mesh; a total of 100 per cent. A minus sign is placed before

Jan 1, 1931

By Earl Bardwell

THE determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. THE EFFECT OF ANNEALING TEMPERATURE ON PHYSICAL PROPERTIES For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows:

Jan 8, 1914

By John E. Hagni, Richard D. Hagni

ORE.ID, a microcomputer program, rapidly searches a database of the principal properties for 573 ore minerals. Searches may be performed on any or all of the following properties: mean Vickers hardness, Talmage hardness, mean reflectance, strength of anisotropism, and colors and tints of the mineral and its internal reflections. Data from the International Mineralogical Association - Commission on Ore Microscopy data card file have been used when available. The program displays the number and type of data matches for each mineral found, displays their chemical components, and allows the range to be narrowed or widened for each of the identification properties for repeated searches, if desired. ORE.ID is much more rapid, allows for the use of more identification properties, and involves more ore minerals than any previous identification system.

Jan 1, 1985

No true conception of the Park City mining district can be obtained without first giving consideration to the part it has played as a consistent producer of mineral wealth. Its position in this regard is almost unique in the annals of a lead silver camp. For over fifty years it has been a continuous producer of lead and silver and for twenty years it has added to the world's supply of zinc. Few camps with its productive history are so little known to the mining fraternity for the reason that its life has never been punctuated by periods of "boom" which serve to attract general attention, neither has it been the field of operation for promoters who temporarily focus attention upon their scene of action. Its history is one of legitimate mining operations. These were at first carried on by a number of smaller companies. A period of consolidation followed and at the present time the entire production of the camp is in the hands of two major companies and one smaller company. These are flanked by a number of prospecting properties, which are at this time actively engaged in the search for ores and later events will doubtless put some of them in the producing class.

Jan 1, 1925

By E. C. Harder, E. W. Greig

Bauxite is known mainly as the ore from which aluminum is smelted but it has large use also in the manufacture of artificial abrasives and in the production of a number of useful chemicals as well as of aluminous cement "ciment fondu." An important and growing use is in the manufacture of refractory products. Composition Dana and earlier mineralogists gave the mineral formula of bauxite as A1203.21120 and the composition as A1202, 73.9 pct; H2O, 26.1 pct. A specific mineral of this composition has, however, never been identified by either microscopic, chemical or X ray examination, and therefore it is concluded that bauxite is a rock consisting of one or more aluminum minerals together with impurities. The term is now used synonymously with aluminum ore and it embraces gibbsite (hydrargillite or alpha trihydrate), A1203. 3H20 (A1203, 65.4 pct; H2O, 34.6 pct); boehmite (alpha monohydrate), A1203•H20 (A1202, 85 pct; H2O, 15 pct) ; diaspore (beta monohydrate), A1203•H20 (A1203, 85 pct; H2O, 15 pct), and mixtures in various proportions of any two of them. Bauxite of the Mediterranean region in Europe is predominantly boehmite, as in France and Istria, subordinately a mixture of gibbsite and boehmite, as in Dalmatia, or of boehmite (or gibbsite) and diaspore, as in Greece. The bauxite of North and South America, tropical Africa, Asia, and Australasia consists largely of gibbsite, but boehmite in appreciable amount occurs in many places. Corundum (A1202) is not included un¬der bauxite, although gradations from bauxite to emery or corundum exist. All bauxite, irrespective of the aluminum minerals composing it, contains certain impurities in variable amount, including silica in the form of clay minerals (kaolinite, halloy site, and others) or quartz, iron oxide (as hematite or goethite), titania (as leucoxene or rutile), iron sulfide (as pyrite or marcasite), iron carbonate (siderite), and calcium carbonate (as calcite); the last three mentioned in minor amount and of local occurrence only. Bauxite belongs to a group of partly consolidated materials called laterites, formed by surface weathering. This group includes also impure siliceous, ferruginous, and phosphatic bauxite and siliceous and aluminous iron ores and manganese ores and nickel and chrome laterites. Phosphorus and manganese minerals locally form important impurities in bauxite deposits. Properties Gibbsite is white or light shades of gray, cream or pink. Its hardness is 2.5 to 3.5; specific gravity, 2.3 to 2.4; crystal system, monoclinic, crystals tabular parallel to 001, often fibrous, concretionary, stalactitic; luster, vitreous to pearly; generally translucent; cleavage, parallel to 001; disassociation temperature, approximately 300°C. Boehmite, a relatively new and important mineral described by J. Boehm15 in 1925, confirmed and named by J. de Lapparen64 in 1930, has some properties not yet definitely determined. It occurs in grayish, brownish, and reddish shades. Its hardness is between that of gibbsite and diaspore; specific gravity, 3.01 to

Jan 1, 1960

By Robert B Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By Robert B. Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By George Holderer

THE Enos Coal Mining Co. owns an area underlaid by coal, of approximately 5000 acres. This property is situated 9 miles from Oakland City, in the southern part of Indiana. The mine has been in operation 5 years, during which time some 350 acres have been stripped, and stripping is now proceeding at the rate of about 100 acres per year. TOPOGRAPHY These coal lands consist of gently-rolling agricultural fields which in times past were farmed for wheat. There is no timber and but very little brush to contend with. The overburden varies from 10 to 60 ft. in depth. A thin bed of slate overlies the coal, followed by limestone, which varies from 3 to 15 ft.; this, in turn, is followed by sandstone, slate, shale and clay. There is a very wide variation in the thickness of all of these beds. The coal has an average thickness of 5 ft., and is a good grade of high-volatile bituminous. MINING OPERATIONS Briefly, the sequence of operations is: drilling holes with churn drills; blasting with L. 0. X.; stripping overburden to, uncover coal and, finally taking up the coal, which is sent to a tipple for cleaning and sizing. In order to show what is being accomplished by the use of L. 0. X., results will be shown from May to November, 1926, inclusive, and compared to the same period in 1925. No work was done in No. 1 pit during May, 1925, hence all figures are unduly low for this month.

Jan 2, 1927

By D. F. Kaufman, H. R. Spedden, A. M. Gaudin

MANY studies of comminution have been made to ascertain the size distribution of the product and to evaluate the work of comminution in the light of the size distributions of the feed and product. Up to now, these studies have been essentially statistical in character, that is, a certain lot of feed was subjected to comminution in some specified way, and the aggregate product was fractionated into sizes, thereby losing all knowledge of individual relationship of feed to product pieces. Radioactive tracers offer a means to do something in this respect which could not be done before, namely, to follow the rupturing of some particular piece in its normal environment of other pieces. That is, it permits going beyond the usual statistical limitations of size distribution studies to what may be termed a personalized or individualized study. The purpose of this paper is to present some preliminary experiments conducted with this tool. The method employed was to mark radioactively some constituent of a feed. It is possible, of course, to consider the preparation of two lots of material of which one is radioactive and the other is not, and to blend the two ahead of the comminuting step; but to do so is open to the objection that the two preparations may not be identical. Therefore a technique has been chosen that removes this objection by merely taking out a size fraction of a comminution feed, rendering that fraction radioactive by exposure to a neutron flux, and then by returning it to Table I. Size Distribution of Offspring Albite Particles Originally 28/35 Mesh and in Admixture with Other Sizes After Grinding 2 min in a Steel Ball Mill Specific Activity ' Cumu- Corrected Distrl- latlve Size for Back- butlon In Distri- Fractlon ground, Weight, Product, button, of Product, cpm/gm g Pctb Pct Mesh (A). (W) (P) (ZP) + 28 0 56.0 0 100.1 28/35 62.6 54.0 24.8 75.3 35/48 62.8 59.4 27.7 47.6 48/65 41.1 53.0 16.2 31.4 65/100 29.6 45.7 10.2 21.2 100/150 23.7 37.0 6.6 14.6 150/200 23.3 25.1 4.4 10.2 200/270 20.1 19.0 2.9 7.3 270/400 17.8 21.2 2.9 4.4 -400 22.9 25.2 4.4 — 100.1 a These activity determinations were made in rapid succession in the order given. The specific activity (Ao) of the active 28/35 mesh fraction of the feed was measured at the beginning, after the measurement on the 65/100 mesh size fraction of the product, and; The end. The decay-corrected activities at those times were 246.7, 241.0. and 236.9 cpm per gm. The weight (W0) of the active 28/35 mesh fraction in the feed was 55.0. b Example of calculation for P in the 65/100 mesh oroduct frac- A W tion; A = 29.6, W = 45.7, Ao = 242.7, Wo = 55.0: P = — x — Ao Wo = 0.102 = 10.2 pet. the remainder of the charge for the comminution experiment. A relatively simple procedure was developed by which albite, containing sodium, was activated in the M.I.T. cyclotron. The cyclotron makes highspeed deuterons which impinge on a beryllium target, thereby producing a concentrated neutron flux. The mineral was exposed to this flux for 2 hr. This treatment changed enough of the sodium to sodium 24 (14.8 hr half-life, 1.4 mev ß) as to make detection and measurement easy. The nuclear reactions taking place were: 11Na23 (n,?) 11Na24 (irradiation) 11Na24 ß,?,? 12Mg24 (decay) The detailed technique of the experimentation was as follows: 40 kg of hand-sorted, lump albite were crushed to pass 10 mesh. After careful mixing of the lot, a screen analysis was made. The whole lot of material was fractionated on standard Tyler screens from 14 down to 200 mesh. Samples for experiments were compounded from these fractions in accordance with the screen analysis. When it was desired to make an experiment in which, for example, the 28/35 mesh size fraction was to be studied, the blend of size fractions was made as indicated above, except that the 28/35 mesh size fraction was added only after irradiation in the cyclotron. The blended charge containing the activated albite was ground for 2 min in a laboratory ball mill with a steel ball charge of controlled size distribution. The ground product was carefully sized on a set of Tyler screens in a Ro-tap. Each size was analyzed for radioactivity by the use of an end-window Geiger-Mueller counter and standard scaling circuit. This analysis was carried out in detail as follows: a 20-g sample was placed in a Petri dish, packed carefully to obtain reproducible geometric distribution with reference to the Geiger-Mueller tube, and the activity was counted for a 2-min period. Several determinations of the activity of the active size fraction in the feed were made at various times to establish the decay in activity with time. Linear interpolation was used to evaluate the activity that the active size fraction in the feed would have had at any given instant. The ratio of the observed activity in a size fraction of the product to the activity that the active size fraction in the feed would have had at the same time gives the fraction in the product size that came from the irradiated size in the feed. The general formula for finding the distribution, P, of a specific individual size fraction in the feed

Jan 1, 1952

By H. M. Morse

This report covers the period from Jan. I, 1943 to Dec. 31, 1943. During the year, II2 wells were drilled in Mississippi, as foilows: wildcats drilled and abandoned, 54; wildcats producing oil, 4; oil wells drilled in oil fields, 26; oil wells drilled in fields, dry and abandoned, 10; sulphur-test wells drilled, 14; salt-water-disposal wells, 3; core tests, I. Prospecting Geophysical work in Mississippi during 1943 amounted to 1127 crew weeks, divided as follows: reflection seismograph, 809 weeks; gravity meter, 285; magnotometer, 30; torsion balance, 3. A considerable amount of core drilling was done over a large part of the state. The complete data on this activity are not available at the present time. Salt Domes To date, the following salt domes have been discovered in Mississippi: Midway, Edwards, Glass, Newman, Tatum, Oak-vale, Kings, Halifax, D'Lo, Hazlehurst, Byrd, Leedo, Prentiss, Carson, Moselle, Monticello, Ruth, Keno, Taylorsville. New Oil Fields Lincoln County.—On March 10, 1943, the California Company completed its Smith No. I in sec. 4, T. 7 N., R. 7 E., Lincoln County, as an oil well and produced 29 bbl. of 25" gravity oil in 24 hr. through a fi-in. choke. Two outpost wells have been drilled in this area by the California Company, and both have been abandoned as dry holes. Madison County. —Love Petroleum Co. completed its J. R. Anderson No. 2, sec. 2, T. 8 N., R. I W., Madison County, on Sept. 7, 1943. This well produced 135 bbl. of approximately 30" gravity- oil in 24 hr. through a )/4-in. choke. The production comes from a sand or porosity in the upper part of the Chalk formation of the Cretaceous age. Adams County.—The California Company drilled its National Gasoline Co. of Louisiana No. I in sec. 52, T. 7 N., R. I W., to a total depth of 10,383 ft., and at 10,280 ft, it perforated and obtained gas and a condensate. The well had several showings in the Wilcox of the Eocene age. Several of these showings were tested and the well finally was completed at 5888 ft. on Oct. 6, 1943, producing 44" gravity oil in the second sand in this formation. No other wells were completed in this field during the year. However, a number of wells are contemplated in the near future, and locations have been staked by the California Company. The Oklahoma Pipe Line Co. will market the oil through its pipe-line facilities. Wayne County.—The Gulf Refining Co. drilled Davis No. I in sec. 2, T. 9 N., R. 9 W. in Wayne County. After several stem tests 545'-in. casing was set at 6850 ft. and production was obtained in the so-called Massive Sand of the Lower Tuscaloosa. The well produced 359 bbl. of oil in 24 hr., and it Was completed on Oct. 4, 1943. Other locations have been staked ill this area and probably will be drilled in 1944 by

Jan 1, 1944

By H. M. Morse

This report covers the period from Jan. I, 1943 to Dec. 31, 1943. During the year, II2 wells were drilled in Mississippi, as foilows: wildcats drilled and abandoned, 54; wildcats producing oil, 4; oil wells drilled in oil fields, 26; oil wells drilled in fields, dry and abandoned, 10; sulphur-test wells drilled, 14; salt-water-disposal wells, 3; core tests, I. Prospecting Geophysical work in Mississippi during 1943 amounted to 1127 crew weeks, divided as follows: reflection seismograph, 809 weeks; gravity meter, 285; magnotometer, 30; torsion balance, 3. A considerable amount of core drilling was done over a large part of the state. The complete data on this activity are not available at the present time. Salt Domes To date, the following salt domes have been discovered in Mississippi: Midway, Edwards, Glass, Newman, Tatum, Oak-vale, Kings, Halifax, D'Lo, Hazlehurst, Byrd, Leedo, Prentiss, Carson, Moselle, Monticello, Ruth, Keno, Taylorsville. New Oil Fields Lincoln County.—On March 10, 1943, the California Company completed its Smith No. I in sec. 4, T. 7 N., R. 7 E., Lincoln County, as an oil well and produced 29 bbl. of 25" gravity oil in 24 hr. through a fi-in. choke. Two outpost wells have been drilled in this area by the California Company, and both have been abandoned as dry holes. Madison County. —Love Petroleum Co. completed its J. R. Anderson No. 2, sec. 2, T. 8 N., R. I W., Madison County, on Sept. 7, 1943. This well produced 135 bbl. of approximately 30" gravity- oil in 24 hr. through a )/4-in. choke. The production comes from a sand or porosity in the upper part of the Chalk formation of the Cretaceous age. Adams County.—The California Company drilled its National Gasoline Co. of Louisiana No. I in sec. 52, T. 7 N., R. I W., to a total depth of 10,383 ft., and at 10,280 ft, it perforated and obtained gas and a condensate. The well had several showings in the Wilcox of the Eocene age. Several of these showings were tested and the well finally was completed at 5888 ft. on Oct. 6, 1943, producing 44" gravity oil in the second sand in this formation. No other wells were completed in this field during the year. However, a number of wells are contemplated in the near future, and locations have been staked by the California Company. The Oklahoma Pipe Line Co. will market the oil through its pipe-line facilities. Wayne County.—The Gulf Refining Co. drilled Davis No. I in sec. 2, T. 9 N., R. 9 W. in Wayne County. After several stem tests 545'-in. casing was set at 6850 ft. and production was obtained in the so-called Massive Sand of the Lower Tuscaloosa. The well produced 359 bbl. of oil in 24 hr., and it Was completed on Oct. 4, 1943. Other locations have been staked ill this area and probably will be drilled in 1944 by

Jan 1, 1944