Search Documents

By Daniel Wild, Tobias Scheffer, Marvin Laugwitz, Martin Jochum

Leveling is a standard process in the rolling mill to eliminate flatness deviations. The process layout is based on models and the leveling result depends on the accuracy of the material parameters in these models. Even small deviations from the correct assumptions can have a major effect on the final flatness. Thus, after leveling the products may look optically flat, but subsequent to a final cutting process springback occurs due to residual stresses. The objective of this work is to analyze the influence of material parameters and gravity on the flatness after leveling. To evaluate the sensitivity of the process, an FE parameter study is exerted that reveals the influence of fluctuations in material properties in the case that the leveling setup is fixed. Gravity is neglected to not conceal flatness deviations. Examples of this study are rerun in a further step under consideration of gravity to also analyze its influence on the resulting flatness and residual stresses. Finally, to analyze the consequence of the residual stresses, all information of the plate from the previous step are transferred while gravity is suppressed to prompt springback. This study revealed that slight deviations of the material properties can lead to uneven plates in simulations where gravity is not considered. If gravity is taken into account, the unevenness is concealed and the plate seems flat. A springback simulation of the same plate shows that strong residual stresses are still present and would lead to unevenness if e.g. the plate were cut.

Oct 1, 2019

By Luis Armando Espitia

AISI 410 martensitic stainless steel specimens were low temperature plasma nitrided at 400°C in a mixture of 75%N2:25%H2, during 20 h. Active screen technic was used to avoid any edge effect The nitrided case is composed of expanded martensite (a’N) and e-Fe3N iron nitride, whilst chromium nitride precipitation was avoided. Surface hardness reached 1275 HV0.01. The transverse microhardness profile shows a gentle hardness gradient with a NHT nitrided case depth of 28 µm. Nanoindentation tests were carried out in order to assess the hardness (H), the Young modulus (E), the H/E and H3/E2 ratios and the elastic recovery (We) of both nitrided and non-nitrided specimens. The cavitation erosion mass losses were measured as a function of exposure time. The results showed a decrease of 27 times of the mass loss compared to the non-nitride specimens. Wear rate decreased from 2.56 mg/h for the non-nitrided condition to 0.085 mg/h after nitriding. The increment in the elastic recovery and the higher hardness values are responsible for the greater cavitation erosion resistance exhibited by the expanded martensite. Such results showed that low temperature plasma nitriding and the formation of expanded martensite are effective to increase cavitation erosion resistance of AISI 410 stainless steel.

Jul 31, 2018

By José Fagundes Jr., Juliano Braz Possatti, Bruno Câmara Vieira, Gabriel Godinho Alves, Bruno Bastos da Silva Murad, Cristina Maria de Oliveira Roque

Driven by market trends, increasing environmental accountability, government regulations and fostered by the Company’s strategic plan, ArcelorMittal Tubarão has developed new steel products to deliver better solutions to fit each customer’s needs. This often translates in higher strength, more complex and dimensionally challenging (thinner and wider) steels to attend a broad array of goals, such as reduction of vehicles fuel consumption and carbon emissions, increase in fatigue performance of heat treated parts, higher load capacity per net weight in vessels or wagons and lower supplying lead time as ArcelorMittal Tubarão establishes itself as a domestic option for so far imported grades. Based on the annual Product Development Plan, a structured workflow involves technical discussions from an operational point of view about safety issues, metallurgical project, steel grade family definitions, offline simulations prior to field trials, deformation resistance and process parameters adjustments and scheduling strategy. As a result of the increasing synergy between the areas, the share of new materials developed in recent years has been sustainably increased up to 15% in 2018, adding value to the final product without impact on hot rolled coil output and with a low cobble index.

Oct 1, 2019

By Edo Engel

Blast furnace No. 3 at Zaporizhstal in Zaporozhye is rebuilt in 2016-2017. The Ukrainian company is targeting increased production and availability, mainly through the use of new technology. Zaporizhstal awarded a contract for a new Top Charging Unit to Danieli Corus, after comparing all available technologies. Reliability of the chosen charging device is pivotal, since long outages may be required for maintenance/replacement jobs, which strongly affects the availability of the blast furnace. This article describes the Top Charging Unit including DANCU (Danieli Charging Unit) - a robust hydraulic system. The main focus employed by Danieli and Danieli Corus during the development of this system has been availability and maintainability of equipment. This chute type charging unit has only few major moving parts, none of which is complex or vulnerable. The article also describes the main challenges of the project at Zaporizhstal, such as the use of hot sinter.

Oct 30, 2017

By Mario SINNAEVE, Olivier LEMAIRE, Gisèle WALMAG, Sébastien FLAMENT

Many hot rolling mills worldwide face nowadays bonding zone fatigue problems before reaching scrap diameter of the work rolls. This phenomenon is nowadays known to occur in reversing roughing mills both in stainless steel and in carbon steel rolling. The phenomenon can be explained through longer rolling campaigns, inadequate backup or work roll maintenance, harder steel grades or increased throughput by reduced amount of passes to achieve the same thickness. In order to help users in optimizing the roll use, we developed a numerical tool to evaluate and optimize roll maintenance. This paper will review the influence of roll geometries on stresses generated at the roll surface but also at the bonding zone. We will also show how roll geometries can decrease contact fatigue damages by modifying crowning and chamfering procedures, shell thickness, material design or campaign length

Oct 1, 2019

By Karl Berger, Michael Steinkogler

The evolution in Metal Cutting: Inventors around the world have been successfully developing innovations for decades, but only some of these developments have had „GAME CHANGING“ potential. One of these innovations is the new developed saw blade LINCUT®, a patented changing system that paves the way for a fundamental reorientation of the entire saw blade industry worldwide through a simple and economical concept for rolling mills or heavy forging lines. Cost efficiency starts with the raw material: Circular saws equipped with a standard saw blade are expected to have a necessary 2 percent standstill per year due to required tool changing. The applied technology reduces this unnecessary loss of production by more than 50%. The ROI can therefore be reached faster which immediately lowers your production costs. No matter what material, conventional carbon steel or highly alloyed stainless steel, the coating and shape of carbide plates is perfected for extended tool life up to 25% with increased performance. Due to LINSINGERs own tool-technology-centre in Austria specialized in research and development of tools, constantly expanding R&D activities, best results are achieved in quality and cost efficiency: a (r)evolution in metal cutting.

Oct 1, 2019

By Karl Berger

The paper gives a comprehensive overview of the historical development of various metal rolling technologies and also describes the influence to industrial and socio-economic developments. The rolling of steel, in particular of rails, beams, rebar, strip and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. All this has changed the face of the world significantly. Further the paper approaches technological highlights in the design, manufacturing, drive and control of modern mills and the various types developed to create industrial economic units for the different markets and customers’ requirements. An outlook of future challenges is as well discussed in the paper. Various solution approaches for the rolling technologies, from continuous improvement of existing plants to more radical new concepts like endless rolling, near net-shape casting and rolling are approached. A positive conclusion is drawn that rolling technologies will remain a valuable area for engineers with scientific and economic challenges, but also a clear vision for positive contribution to further industrial and social development.

Jul 30, 2018

By Patrícia Mundim Campos Faria

The process of particle size reduction by grinding is inherently inefficient and involves high capital and operating costs. In particular, ball milling is one of the important unit operations in the iron ore pelletizing process. The mill product, due to its physical properties, determines the efficiency of subsequent stages of classification, filtration and pelletizing, thus impacting the quality of iron ore pellets. The work demonstrates the application of the population balance model in the optimization of a full-scale ball mil circuit grinding pellet fines with the aim to evaluate the optimal solids concentration to improve iron ore pellet quality. Initially, detailed experimentation was carried out in a 25.4 cm diameter batch mill and a relationship for mill scale-up using a linear population balance model in wet grinding systems was established. The selection and breakage parameters and the specific selection functions were determined for pellet feed iron ore. It was possible to identify the non-normalizable nature of the breakage functions of the ore studied, which were modeled properly. Afterwards, as a result of incorporating the specific selection functions and breakage functions into the linear population balance model, it was possible to predict product size distributions in the pilot and plant scale mills (0.416 and 5.18 m diameter, respectively) from data obtained in the 25.4 cm diameter mill. Finally, with this scale-up procedure it was possible to appraise the plant scale optimization via laboratory scale grinding mill tests. The effects of changing percent solids were assessed in order to improve the industrial mill performance and the optimal value should be in the range from 76 to 80%.

Aug 1, 2018

By Gerhard Finstermann, Ichiro Maeno, Takehiko Saito, Hironori Shimogama, Konrad Krimpelstätter

Automobile manufacturers are developing Electrified Vehicles with light steel body structure designs that reduce mass and therefore greenhouse gas emissions over the vehicle’s entire life cycle. This raises the demand for the production and development of Advanced and Ultra High-Strength Steels (AHSS / UHSS) and Electrical Steels with increased permeability and reduced core loss to improve energy conversion efficiency. To meet this requirements the steel market is tending towards new generations of AHSS with improved formability (3rd generation AHSS) and high-silicon steels with higher strength and thinner products. With this growing demand for advanced high-strength steels and electrical steels, producers are faced with a unique and interesting challenge in producing materials that strain or exceed the capabilities of existing mill equipment and automation designed to produce low- to medium-carbon sheet. While specialty steel producers have known for decades how to process special high-strength steels and thinner gauges, this equipment typically does not offer the yield and productivity desired by the market, necessitating innovation in re-engineering existing equipment to meet the market demands more economically than new construction. In the case of cold rolling, this can be supported through variable roll geometries, more effective roll-gap lubrication technologies, application of strip heaters (Warm Rolling) to reduce risk for edge crack propagation and strip breaks as well as continuous rolling managed by state-of-the-art automation technologies.

Oct 1, 2019

By Giuseppe Pintaude

This study aims to evaluate the effect of specimen preparation on the dry sliding wear behavior of CA-6 NM stainless steel. Two different surface finishing manufacturing processes were applied: lapping and metallographic polishing. The wear tests were conducted in reciprocating ball-on-flat system, performed for two loads: 5 or 8 N. For all test conditions, hardmetal ball was employed as counterbody. The surfaces were evaluated using 3D interferometry technique to determine their surface roughness, including texture analysis regarding isotropy. Surface characterization results indicated the presence of texturing and preferential orientation, since the parameter Str was smaller than 0.5 for samples of both the studied conditions. Two distinct levels of isotropy evaluated through Str parameter were achieved: 0.13 for lapping and 0.3 for metallographic polishing process. It is clear from wear tests that the variation of average surface roughness is the key point for tribological behavior of CA-6 NM stainless steel.

Jul 31, 2018

By Paolo Demetlika

In this paper it is shown how the “Zero Operator” concept on the casting floor has been reached by adoption of a standard 6 axis industrial anthropomorphic robot coupled with the most innovative machine vision technology. This has been achieved by automating all the operations related to the ladle and tundish activities, including shroud manipulation, powder addition, ladle nozzle identification, nozzle opening by lancing, temperature measurement and chemical sampling. Q–Robot CAST family products are the result of the successful alliance between industrial robotics and the most advanced technology in process automation. This led, for each production area, to the introduction of flexible automation in dangerous places, even where some degree of human intervention is still necessary. By using anthropomorphic robots, human operators can be reassigned to safer environments. Furthermore, robots are suited to deal with repetitive and labor intensive tasks thus guaranteeing a high process quality.

Oct 30, 2017

By Christoph Aichinger

A smart combination – Primetals Technologies developed the Circular Pelletizing Technology (CPT), which is a combination of the well-proven travelling-grate pelletizing technology with the design of a circular dip rail cooler of modern sinter plants. The overall space requirement and the installed weight for a CPT plant is significantly less compared to conventional technologies and by that CPT is a very attractive alternative for new projects.

Aug 16, 2017

By Jörg Busch

The essential pre-requisite for attaining the high quality of product required from high-speed continuous production processes is the use of new measurement and control technologies. High availability and reproducible measuring results ensure the high level of process stability necessary for full continuous operation. The requirements for the optimisation of quality across the complete production process and for quality analysis systems will be discussed. This report will present examples of basic and new measurement technologies in Cold Rolling Mills and Processing Lines. The following gauging systems will be discussed in detail: Strip tension meter, roll force measurements, weighing systems and shapemeter rolls. The measuring and control systems in this presentation must be seen as high-tech solutions in the field of processing technology. The measuring methods and technologies described are, together with optimised process models and precision control loops and actuators, the main pre-requisites for achieving the quality of product required from high-speed continuous production processes. Interconnected quality management systems enable optimisation across the complete production process.

Jul 30, 2018

By Carlos Alberto Perim

Devido à obstrução no distribuidor, os aços ultra baixo carbono estabilizados ao titânio apresentavam baixo sequencial de lingotamento na ArcelorMittal Tubarão (AMT). Foram identificadas práticas utilizadas na redução de obstrução nestes aços, que foram adotadas para a produção na AMT. Uma das práticas foi estabelecer uma relação entre alumínio e titânio com menor propensão à formação de compostos de alumina e óxido de titânio que se aglomeram na região da válvula superior do distribuidor. Também foram introduzidas melhorias no processo visando a melhorar a condição de fluxo na região próxima da saída do aço no distribuidor. Neste projeto, um aço UBC de maior volume de produção foi escolhido e novas práticas foram adotadas para sua produção. Amostras de aço foram retiradas de corridas produzidas nesta condição e foram enviadas para análise na ArcelorMittal Research USA. Os resultados mostraram melhorias nos índices de qualidade tanto em laminados a quente como em laminados a frio. Neste trabalho será apresentado um resumo das ações adotadas na AMT, que resultaram em um aumento do sequencial médio de distribuidor, permitindo atingir um máximo de 18 corridas. Os níveis de esfoliação com esta nova prática atingiram também nível mínimo histórico.

Aug 16, 2017

By Danilson Gonçalves de Melo e Silva

O balanço de energia realizado em um forno de aquecimento de tarugos apresentou rendimento de 53%. A maior perda energética estava relacionada ao sistema de refrigeração dos skids, cujo valor calculado foi de 18%. Objetivando minimizar tais perdas, estudou-se a utilização de um novo tipo de revestimento refratário para esta região. O fabricante de refratários apresentou uma estimativa de ganho de 62%. Desta forma, a VBR planejou um teste para validar a eficiência do refratário proposto. Neste teste, o produto foi instalado em uma viga auxiliar. Esta viga foi instrumentada, e foram registrados dados de vazão, pressão e temperatura do fluido de refrigeração (água). Objetivando comparar estes valores com o material convencional anteriormente instalado, outra viga com as mesmas características (dimensões e posição no forno) também foi instrumentada. Posteriormente, foram feitos os balanços de energia em cada viga para quantificação das perdas de energia térmica. Os resultados encontrados mostram uma redução de 92% da perda térmica relacionada ao sistema de refrigeração dos skids. Considerando a eficiência do forno de 53% e a redução de 92% da perda térmica, estima-se uma economia de R$ 1.200.000 por ano.

Sep 25, 2017

By Geraldo Lúcio de Faria

O parafuso Tirefond é um importante componente da via permanente ferroviária. Ele é um componente de fixação responsável por fixar a placa de apoio que, por sua vez, garante a estabilidade dos trilhos. Este componente é comumente fabricado no Brasil por processos de conformação mecânica a quente de aços baixo carbono. Entretanto, com o aumento da carga transportada por eixo de locomotiva nos últimos anos, este componente tem falhado de forma recorrente em serviço. Com o objetivo de entender os efeitos dos filetes do parafuso sobre o comportamento mecânico do componente, este trabalho apresenta um estudo sobre a susceptibilidade do parafuso à concentração de tensões sob carregamento estático. Análises químicas por espectrometria de emissão óptica, análises microestruturais por microscopia óptica, ensaios de tração e dureza foram realizados. Por meio da aplicação de modelos computacionais, foi possível determinar a distribuição de tensões ao longo do parafuso, assim como entender as principais causas destas falhas recorrentes. Fazendo-se uso de modelos matemáticos de mecânica de fratura, associados a simulações computacionais de carregamento estático, foram propostas modificações no projeto original do parafuso que prometem melhorar o seu desempenho em serviço.

Aug 16, 2017

By Mário Martins de Oliveira Júnior

Na maioria das aplicações tribológicas, lubrificantes líquidos ou graxas são utilizados para combater o atrito e o desgaste. Mas quando as condições tornam-se muito severas, os lubrificantes sólidos podem ser a única opção para este controle. Uma combinação de lubrificantes sólidos e líquidos é viável e pode ter um efeito sinérgico benéfico na redução do atrito e no aumento da resistência ao desgaste das superfícies de deslizamento, em especial nos regimes elasto-hidrodinâmico e limite de lubrificação. Este trabalho visa estudar o efeito conjunto da lubrificação sólida (compósitos sinterizados contendo partículas de lubrificante sólido dispersos em uma matriz metálica por um processo de mistura simples) com a presença de um lubrificante líquido em regime de lubrificação conjunta em uma configuração de desgaste por deslizamento alternado. A utilização simultânea de lubrificantes sólidos e líquidos produz uma diminuição significativa no coeficiente de atrito (25%) quando comparado com a adição do lubrificante líquido apenas, sugerindo a existência de uma sinergia positiva entre os lubrificantes sólidos e líquidos. Esta ação conjunta reduz o coeficiente de atrito (cerca de 4x) e a taxa de desgaste em 50%.

Aug 16, 2017

By Charles Henrique Xavier Morais Magalhães

Os Aços Inoxidáveis Duplex possuem uma estrutura constituída basicamente por ferrita e austenita na proporção aproximada de 50%. Este trabalho estudou a influência da temperatura de um tratamento térmico na morfologia e fração de ferrita e austenita no aço UNS S32304. Os tratamentos térmicos realizados consistiram no aquecimento das amostras, desde a temperatura ambiente até a temperatura de 1250°C, seguido de um resfriamento lento em um segundo forno estável em uma determinada temperatura. As amostras permaneceram neste segundo forno por um intervalo de tempo necessário para que suas temperaturas atingissem exatamente um valor desejado, sendo então imediatamente retiradas e resfriadas em água a 20°C para preservar a estrutura resultante do ciclo térmico aplicado. As amostras foram metalograficamente preparadas, atacadas e analisadas com o auxílio de um microscópio ótico. As frações de fases medidas por MO se aproximaram dos resultados obtidos por simulação utilizando o software Thermo-Calc. A morfologia das fases variou significativamente com a diminuição da temperatura de tratamento, uma vez que a austenita se mostrou mais fragmentada nas temperaturas mais baixas, porém o bandeamento não deixou de existir na estrutura.A transformação da ferrita em austenita se mostrou fortemente dependente do tempo.

Aug 16, 2017

By Rafael Malagutti Leandro

O objetivo deste trabalho é avaliar a influência do tempo e temperatura de tratamento térmico de solubilização no tamanho de grão e na fração de ferrita de um aço inoxidável dúplex UNS S31803 (SAF 2205). A chapa do aço em estudo foi laminada com 22% de redução de espessura antes de ser solubilizada a 1.000°C, 1.100°C e 1.200°C, por tempos de até 96 h. A fração de ferrita das amostras foi obtida por medidas magnéticas em ferritoscópio e por estereologia quantitativa. Já o tamanho de grão foi determinado por estereologia quantitativa de imagens obtidas por microscopia óptica. Observou-se o aumento da fração de ferrita em função da temperatura de tratamento, como esperado, e foi realizado comparativo entre as duas técnicas de determinação da fração de ferrita com simulações de equilíbrio em Thermo-Calc®. O intercepto médio das amostras solubilizadas a 1.000°C manteve-se praticamente constante em todos os tempos de solubilização estudados, em aproximadamente 9 micrômetros; após 5h de solubilização a 1.100°C, e após 30 min a 1.200°C, contudo, observou-se significativo crescimento de grão nas amostras.

Aug 7, 2018

By Niédson José da Silva

Ligas com memória de forma (LMF) são materiais ativos que apresentam como característica a resposta a impulsos externos, recuperando deformações aparentemente plásticas. Esses materiais têm forte potencial aplicativo como atuadores termomecânicos em diversos setores industriais, sendo de interesse o aperfeiçoamento de suas propriedades termomecânicas. A conformação mecânica do ECAE (Equal Channel Angular Extrusion) resulta em melhorias quanto às propriedades mecânicas destas ligas. Esta melhoria está relacionada à redução de tamanho de grãos devido ao cisalhamento interno que estes sofrem ao passar pelos canais interceptantes, apesar de não ocorrer nenhuma alteração na área da seção transversal do corpo de prova. Neste trabalho, realizou-se a fabricação de ligas com memória de forma da família NiTi e da matriz para a extrusão em canal angular. A conformação mecânica foi realizada numa máquina de ensaios universal. O resultado desse estudo foi a observação da melhoria das propriedades mecânicas e alteração das temperaturas de transformação, as quais são essenciais para a utilização do efeito de memória de forma. Essa análise se torna relevante quando da aplicação desse tipo de material em situações em que se requer elevada resistência mecânica aliada a eficácia dos fenômenos de memória de forma.

Aug 8, 2018