Search Documents

By Xuemei Zheng, Aiyuan Ma, Yonggang Zuo, Jinhui Peng, Shiwei Li, Libo Zhang

The effect of moisture content on the dielectric properties and microwave drying behavior of zirconium hydroxide was studied by using an open-ended sensor dielectric measurement system at the frequency of 2.45 GHz. The experimental results showed that moisture content can significantly influence the variation of dielectric properties. Dielectric constant, loss factor and loss tangent all increase with the increasing moisture content. Compared with the conventional drying method, the microwave-assisted drying method resulted in a substantial decrease (81.8%) in the drying time, and the drying effect was better at the lower power level of 600 W. This study offers the useful information on dielectric properties of zirconium hydroxide, which can be used for developing microwave drying applications in mineral processing and designing better microwave sensors for measuring zirconium hydroxide moisture content.

Jan 1, 2015

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang, Xiaohui Fan

"Presently, high-grade manganese oxide ores are usually utilized by a coal-based reduction roasting process. However, there were some obvious drawbacks, including serious environmental pollution, high energy consumption, etc. The reduction temperature is relatively high (850-900 °C). In this study, a kind of biomass, pine black charcoal, was used as a reductant to reduce low-grade manganese oxide ores. Under the optimal conditions of reduction temperature of 600~650 °C, roasting time of 30~45 min and ratio of ore to reductant 5:1, the leaching efficiency of manganese reached more than 98%. Compared with the traditional coal-based reduction process, the reduction temperature is reduced by 250-300 °C.IntroductionManganese plays a very important strategic role in the national economy, and it is widely used not only in the metallurgical industry, but also in the light industry, chemical industry, medicine, agriculture, etc [1]. The average grade of manganese ores in China is evenly about 21%, which belongs to typical low-grade manganese ores [2]. Therefore, large quantity of high-grade manganese ores is required to import in order to meet the rapid development of Chinese manganese industry. As reported, the conventional treatment of reduction roasting has been widely applied for processing manganese oxide ores, in which coals or reducing gases (CO, H2 or CHi) were usually used as reducers [3]. However, there were some insuperable problems, such as high energy consumption, poor operating conditions, serious environmental pollution, etc [ 4-9]."

Jan 1, 2013

Acid mine drainage containing heavy metal ions is a large environmental problem facing the mining and mineral processing industry. The femte coprecipitation is a novel technique for removing heavy metal ions from waste water, recently applied to acid mine drainage. The fenite precipitation is usually performed at high temperature and therefore if applied in conventional manner, it becomes uneconomical to treat large quantities of acid mine drainage. In this paper the ferrite precipitation at ambient temperature-is &died. The possible mechanism of ferrite formation is discussed Experimental results from Noranda Tailing and Berkeley Pit water treated by this process are presented.

Jan 1, 1994

By S. Tandon

Equilibria studies of selenium distribution for sodium-borate slags were initiated at 1473k under reducing condition as a function of slag composition and alloy composition. The Se distribution coefficient (% Se in slag/% Se in metal) increased from 0.4 to 2.9 with increase in basicity (0.53 to 0.86) for Cu-0.446% Se alloy. However, the results are not very useful from industrial application viewpoint. Therefore, in order to improve the distribution of Se, CaO (10% to 50%) was added to the sodium-borate slag of basicity 0.864. On addition of 502 CaO, the distribution coefficient increased roughly by 100% for slag composition - 44.5% Borax, 22.2% Na2C03, 33.3% CaO and Cu-0.44677 Se alloy. Further, the value of this distribution coefficient has been found to increase by an additional 80% on addition of 20% CaF2 to the above slag for all Cu-Se alloy compositions. Also with increase in initial concentration of Se, the distribution coefficient has been noted to increase.

Jan 1, 1992

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3-PbZrO3-Pb(Mg1/3Nb2/3)O3) system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densifieation by the normal sintering was slow even at high temperatures. When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.

Jan 1, 2003

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3 PbZrO3-Pb(Mgl/3Nb2/3)O3 system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densification by the normal sintering was slow even at high temperatures, When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.-

Jan 1, 2003

By Osvaldo A. Bascur

Several new hydrometallurgical plants have been built in the past years. They have implemented new processes to treat new type of ores. New technologies have been used to improve metallurgical performance from the start. The cycle times between knowledge generation and innovation are often neglected in the traditional capital expenditures and building of these new process plants. The paper reviews several implementations in which they have started with new ways of using information management from the beginning. The implementation of a real time performance management infrastructure is reviewed to assist in the implementation of mine to product strategies, metallurgical mass balances, solvent extraction composition statistical process control, methods to minimize organic losses, reduce variable costs and to improve metal extraction. Several examples are provided to improve operations by simplifying the access and analysis of information from assets and metallurgical processes. Continuous improvement and innovations have been enabled to minimize start times and for faster troubleshooting and resolution of operational problems.

Jan 1, 2006

By T. E. Warner

In order to detect arsenic and antimony in zinc, various electrochemcial experiments were performed involving the electrochemical introduction of sodium atoms into molten zinc using a solid electrolyte. Under high rates, the formation of the intermetallic phase NaZn13 was assumed to form. Under more moderate injection rates of sodium, employing a symmetric "zinc/zinc cell", a qualitative relationship between the current generated during cyclic voltammeuy and the arsenic and antimony concentrations in molten zinc was observed.

Jan 1, 1999

By Muhlis Nezihi Saridede, Burak Birol

"The scraps of high quality steels generally contain expensive alloying elements such as chromium, vanadium, nickel, etc. These scraps are melted in an induction or an electric arc furnace and refined in ESR (Electroslag Remelting) purification process. A significant amount of alloying elements are lost during these processes. In order to avoid these losses, scraps can be utilized directly in ESR by skipping the melting step. In this study, 316L stainless steel scraps were refined in ESR with selected synthetic slags. The products were analyzed by optic emission spectrometry and the effects of slag compositions on the alloying element losses were examined. According to the analysis of the scrap and the products, generally chromium, nickel and manganese losses were encountered. It was determined that the alloying element losses has no connection with electrical conductivity. The slag containing CaF2, Al2O3, and FeO gives the optimum Cr and Ni losses.IntroductionElectroslag remelting (ESR), which is the consumable electrode refining process, finds a wide range of utilization for the production of high quality, low inclusion alloys. This process is based on melting a consumable electrode under a molten synthetic slag containing CaF2, Al2O3, CaO etc. The synthetic slag provides the chemical refining and insulation of molten metal from air which leads to a higher purity and an inclusion-free product. [ 1,2] A schematic diagram of ESR system is shown in Figure 1."

Jan 1, 2011

By Sergio N. Monteiro

Jute fabric obtained from discarded sackcloth is a promising low cost and post-used material being considered as reinforcement of polymeric matrix composites. In particular, the combination of this fabric with a recycled plastic constitutes an environmentally correct composite with both economical and environmental advantages. The present work investigates the toughness of recycled polyethylene composites reinforced with up to 40 wt% of post-used jute fabric extracted from discarded sackcloth. Standard Izod notched specimens were impact tested and the results showed an increase in toughness with the amount of jute fabric. Observation of the composite fracture by SEM revealed that the fabric weave, in spite of damages caused by the previous use of the sackcloth, act as an effective obstacle to crack propagation.

Jan 1, 2009

By F. Kongoli

Nonferrous and ferrous smelting industries have recently faced the unavoidable necessity of changing and/or improving the smelting technologies as a result of the use of new raw materials which are becoming available from different geographical areas. These new feed materials usually contain different ore composition and higher level of minor components, which adversely affect the smelting process. Due to the problems encountered in several processes as a result of this feed diversification some work has been undertaken in order to make uniform the feed and avoid later surprises in the smelting process. However this has proven to be very difficult and sometimes almost impossible. In this work a more viable approach is undertaken to deal with this problem. It consists of controlling not the cause of the problem i.e. the feed composition but instead the results of this feed change, i.e. the end-point of smelting technologies. It is shown that this approach, when carried out through advances physicochemical modeling and simulation tools is not only easier and less costly but it also helps the control optimization and automation of the smelting processes. Several examples are given and future work is underlined.

Jan 1, 2003

By Yuanbo Zhang, Xiaoming Mao, Zhixiong You, Zhenyu Fan, Tao Jiang

"It is generally known that the formation of calcium ferrite is favorable during the iron ore sintering, which dominatingly contributes to the improvement of strength and reducibility of the finished sinters. In this study, effects of roasting temperature and 02 content of inlet gas on the sintering mineralization properties of typical iron ores, including hematite, limonite, specularite and magnetite, were investigated. The results showed the amount of calcium ferrite initially increased then decreased with the increase of the roasting temperature. The temperature of maximum calcium ferrite generation amount for different iron ores was determined as follows: hematite and limonite was 1275 °C, whereas specularite and magnetite was 1250 °C. Increasing 02 content of inlet gas was advantageous to the generation of calcium ferrite during the sintering. The sequence of 02 content affecting the mineralization properties of different iron ores was determined as follows: magnetite > hematite > specularite > limonite.IntroductionThe mineralization property of iron ore plays a significant role in the mineral composition and microstructure of finished sinters, which determine the quality and output of the sinters [1-2]. The mineralization process of sinters is composed of solid-phase reaction, formation of liquid-phase and crystallization. The formation and crystallization of liquid-phase is the foundation to the mineralization as the quality of the sinter is poor when concreted by solid-phase consolidation [3-4]. With respect to the iron ore sintering, liquid-phase regarded as bonding phase is generated between the iron ores and fluxes at high temperature [5]. Calcium ferrite is the most favorable liquid-phase among the bonding phases which dominatingly contributes to the improvement of strength and reducibility of the finished sinters [6-8]. Especially for high iron-low silicon sintering and high basicity sintering, making sure sufficient calcium ferrite quantity and reasonable distribution is crucial to the sinters [9-10]. Therefore, carrying out the researches on the high temperature reaction properties of iron ores is of great significance [11]."

Jan 1, 2013

By Deepu Philip, Pratik Agarwal, Ajay Kumar Shukla, Ishani Shukla, G Rajesh

Steel plants generally employ static BOF end point control models to arrive at a given temperature and chemistry at the end of blow. These end point models have now been supplemented with chaos control models to steer the blowing process in the right direction while the blow is in progress. Merely arriving at the correct end point temperature is however not adequate because in the subsequent stages as well the temperature variations can be large and unpredictable. The present paper deals with an integrated model to take into account the effect of all parameters affecting temperature and composition from tapping to the start of casting to minimize the use of LF or aluminum heating, and also minimize grade mixing. The application of lean operations strategy is explained in which the previous “Push System’ is changed to a “Pull System”, minimizing the use of ladle furnace or aluminum heating during steelmaking.

Jan 1, 2014

By Beate Ina Jenssen

Ferric iron removal from the nickel electrolyte at Glencore Nikkelverk AS in Kristiansand, Norway, is achieved by precipitation of iron hydroxide followed by filtration, and it is desirable to improve filtration properties of the precipitated iron hydroxide in order to decrease the filtration time. The effect of increasing the residence time from the current 45 min to 75 min and temperature from 65 °C to 90 °C on the filtration properties of the precipitated iron hydroxide (akaganéite) was studied by simulating the industrial process conditions in a continuous reactor setup operating at steady state, using ferrous-containing process solution as feed material. It was possible to decrease the filter cake resistance by both increasing residence time and temperature, but temperature gave the most pronounced effect and reduced the filter cake resistance by one order of magnitude.

By M. A. Cocquerel

The future economic necessity of mining copper ores with a high impurity content and increased environmental awareness will require closer examination of the distribution of arsenic within copper smelting processes. A generalized approach is developed which can be adapted to specific projects for the determination of an overall process configuration to satisfy all requirements in a cost effective manner.

Jan 1, 1983

By C. Ramasamy

The tariff reductions on imports, as a part of on-going liberalisation process in India, has fueled competition within and outside India and has, in turn provided an opportunity to reach global markets. This change calls for quality upgrades and cost-competitiveness without impairing the environment. In this context, gas based processes, contributing to improvement in quality and environment as well as processes where controls are applied when gases inimical to environment are involved, are discussed in a remelt/cast-house scenario. The impact of such processes on fabrication cost of sheet ingot is seen alongwith consumption and cost of materials and compared with a world class standard plant in North America.

Jan 1, 1996

By Wenbin Liu

A novel route for rapid synthesis of ultrafine WC-Co cemented carbides with homogeneous binder phase distribution is reported. The composite powder is produced by in situ reduction-carbonization reactions by using WO2.9, Co3O4 and carbon black as raw powders. The reaction equilibrium and phase stability are studied by thermodynamic calculations. The WC-Co composite powder is condensed by spark plasma sintering (SPS) to obtain the cemented carbides bulk. The sintering temperature is lower than that in the conventional sintering methods by 1500C, while the sintering time is remarkably reduced by 3-5 times. The high performances of the hardness and the fracture toughness are obtained. The experimental results confirm that the present processing scheme of in situ reduction-carbonization reactions and subsequent SPS sintering is an efficient way to prepare WC-Co cemented carbides, and is apparently superior to the conventional long-period techniques of preparing composite powder and cemented carbides bulk.

Jan 1, 2008

By Yuanbo Zhang, Guihong Han, Guanghui Li, Tao Jiang, Zengqing Sun, Yanfang Huang

"Because of small specific surface area and poor ballability, vanadium/titanium-bearing magnetite is difficult for production of oxidized pellet. A novel organic copolymer binder, modified humic acid (MHA), has been authorized recently in China. Effects of the novel MHA binder on the quality of V/Ti-bearing magnetite pellets are studied in this paper. Experimental results show the MHA binder can obviously improve the strength of green pellet. Because of better heat endurance, the MHA binder pellet has a higher strength than Peridur pellet under the same preheating conditions. Moreover, TFe grade of pellet with the MHA binder is much higher than that of the bentonite pellet. The strength of preheated pellet containing MHA binder of 0.25%~1.0% meets the requirements of oxidized pellet production by grate-kiln process. Comparatively, MHA is a promising orgainc binder for iron ore pellets. Its price is only one tenth of Peridur price and about 3 times of bentonite price.IntroductionThe iron-making practices show that the use of pellet is beneficial to blast furnace life, productivity and fuel savings. Therefore, many iron-making plants have expanded the production of oxidized pellets in order to meet the needs of modern large-scale blast furnaces [1]. Presently, bentonite is widely used to improve the quality of iron ore pellets. The negative effects of using bentonite include decreasing total iron (TFe) grade and degrading the metallurgical properties of the final products [2, 3]. Many studies, therefore, have been conducted on the application of organic binders to overcome the weakness of the inorganic bentonite. In comparison with inorganic binders, one of the biggest strengths of organic binders is low residual silica content [4]. However, those studies showed that the economics of foreign organic binder addition into pellets was not attractive. For example, the compression strength of preheated pellets and roasted pellets are both too low, resulting in powder generation and ring formation in the industrial rotary kiln [3, 4]."

Jan 1, 2011

By Alaina Mallard, Jannette Chorney, David Hutchins, Grant C. Wallace, Jerome P. Downey

Current commercial processes for producing ceramic carbides require temperatures of 1400–2000 °C and often use extensive milling operations to produce a powder product. A process that could reduce the energy requirements of commercial carbide production could allow for these materials to be implemented in a greater number of applications. In this study, tungstate (WO4 2−) and silicate (SiO3 2−) anions were adsorbed onto activated carbon and converted into silicon carbide (SiC) whiskers and a mixture of tungsten and tungsten carbide (W/WC) crystals via carbothermal reduction using inert and reducing gas atmospheres at temperatures much lower than what is required by current commercial processes (950 °C for W/WC/W2C and 1200 °C for SiC). The adsorption process was statistically-optimized via a central composite response surface analysis using DesignExpert 9. Inductive coupled plasma optical emission spectroscopy (ICP-OES) was used to measure, and optimize, adsorption efficiency while the carburization products were characterized using X-ray diffraction and scanning electron microscopy.

Mar 1, 2017

By James Bennett, Jinichiro Nakano, Anna Nakano

Previous empirical research demonstrated that by mixing gasification and metallurgical slags at a specific composition in a CO2 enriched environment, enough exothermic heat would be generated to transform CO2 to CO. The process capacity may be limited by the availability of the slags, however, it could be used to supplement existing energy or chemical production to reduce overall carbon emission. In this study, computational simulations were performed to explore optimal process conditions based on effects of individual slag constituents and thermal input for maximal gas conversion rate, heat production, and volume increase. In simulated conversions of CO2 to CO and H2O to H 2, comparisons were made by varying CaO, FeO, versus V2O3 slag constituents. The result indicated the optimal slag composition may be obtained by appropriate source selection and mixing of gasification and metallurgical slags in order to maximize carbon reduction and/or H2 production.

Mar 1, 2017