Search Documents

By Kenneth L. Driggs

The 1988 shift in primary smelting facilities from low grade matte (35%) reverberatory furnaces to high grade matte (63%) flash smelting heavily impacted a very stable and successful converter operation. Low matte grade converter campaigns averaged 36,000 short tons of copper and revert production/consumption was in balance. The conversion to high matte grades necessitated oxygen enrichment of converter blast and revisions in operating practices. After two years of operational development, campaign life has risen to over 40,000 short tons and revert production/consumption is again in balance.

Jan 1, 1991

By C. Palacios

The Plant, which was started up in April 1970, was originally designed for a capacity of 40.000 ton of cathodes per annum, using 12 sections, containing 408 cells. Since then the addition of another 8 sections containing 280 cells and using the Reverse Current System has made possible the increased output of 109.000 ton. The quality of the cathodes produced is excellent. The extension of the Electrolytic Refinery, by the introduction of the Reverse Current System, has been a great success and no problem has arisen in the new equipment or in the modifications carried out in the plant. The operation of the plant has improved due to better control procedures.

Jan 1, 1976

By Craig A. Johnson

Cyanide speciation and behavior have been examined at three active heap leach operations, three heaps undergoing rinsing, and three sites with cyanide contaminated groundwater, all in the southwestern U.S. Data from these studies demonstrate that strong cyanometallic complexes of iron and cobalt can play ?an important role in cyanide behavior throughout the lifetimes of heap leach operations. In active circuits, we find evidence that significant amounts of cyanide combine with iron and cobalt to form strong cyanometallic complexes, and that these species can be adsorbed, probably onto iron hydroxides, or precipitated as insoluble cyanometallic compounds. When spent heaps are rinsed, the release of this cyanide is likely controlled by the slow kinetics of desorption from, or dissolution of, solids that have gone largely uncharacterized. We find evidence that strong cyanometallic complexes can give rise to transient free cyanide in some settings by rapid photo dissociation where heap rinse effluent is exposed to sunlight in open channels or translucent sample bottles. Thus, these species can complicate the ,preparation of spent heaps for decommissioning, even where regulatory standards ?are based on weak acid dissociable cyanide. There is a critical need for information on the form and stability of adsorbed and precipitated cyanide in spent ore heaps, on the concentrations of strong cyanometallic complexes in mineral processing effluents -particularly the complexes of cobalt, and on the natural attenuation of iron and cobalt cyanometallic complexes in both surface and subsurface waters.

Jan 1, 1998

By S. Illendula, B. Q. Li, R. A. Mirshams

"An integrated mathematical model is developed to represent the thermomechanical behavior of the materials and microstructure evolution during metal forging. The model development is based on the finite element solution of the thermoviscoplastic deformation of metals coupled with the internal state variable model describing the microstructure evolution involving work hardening, recovery, recrystallization and grain size distribution. The procedures for the integration of the microstructure model into the macro finite element model are described. Computed results for both macro and micro phenomena during metal forging, such thermomechanical deformation such as velocity field and effective strain rate and materials characteristics such as distribution of grain size and recrystallization volume fraction, are presented.1. IntroductionThermomechanical behavior and material microstructural evolution are two critical, interrelated aspects associated with metal workpiece undergoing large plastic deformations such as encountered in forging processes. In much of the modeling work up to date, these two aspects have been addressed separately. Die designs and forging processes are investigated using finite element based thermomechanical models while material dynamics during forging is studied, more often than not, as a separate subject. For many industrial applications, especially those involving novel, light and high strength materials, it is critical to combine these two aspects into a single, integrated model so that materials dynamics and thermomechanical deformation during forging processes can be considered simultaneously [1], thereby providing required information for intelligent process design and optimal process control."

Jan 1, 1998

By C. J. Beyke

The U.S. Bureau of Mines has developed a process for the selective recovery of Pb metal from a mixed Pb-Zn concentrate. The concentrate was leached in recycled H2SiF6 at atmospheric pressure and 95° C with a redox potential of 570 mV (Eh). Eighty-five pct of the Pb was selectively leached from the concentrate while 87 pct of the Zn remained in the residue. Pressure leaching of the concentrate was slightly less successful, with 78 pct of the Pb leaching from the concentrate and 80 pct of the Zn remaining in the residue. Pure Pb metal was successfully electrowon from a purified PbSiF6-H2SiF6 solution with 96 pct current efficiency and 0.69-kW.h/kg energy consumption.

Jan 1, 1991

By W. K. Connor, O&apos

The U.S. Bureau of Mines, in cooperation with the Idaho National Engineering Laboratory (INEL), conducted over 30 hours of melting tests to vitrify simulated low-level radioactive wastes from the INEL Radioactive Waste Management Complex (RWMC). Five separate waste compositions were investigated, each consisting of noncontarninated soil from the RWMC and surrogate materials used to simulate the actual buried wastes. The RWMC soil and five waste compositions were melted in a 50-lb, single-phase electric arc furnace with a water-cooled shell. These tests were conducted to determine melting parameters in preparation for a large-scale melting campaign to be conducted in the Bureau's 1-metric ton (mt), water-cooled-wall, 3-phase electric arc fumace. Bulk chemical composition was determined for each of the feed materials and for the slag, metal, fume solids, and offgas furnace products, and distributions were calculated for the key elements. The material balance for the furnace operation indicates that from 63 to 84 pct of the feed reported to the slag. Cerium, used as the surrogate for the radionuclides in the wastes, demonstrated an extremely strong affinity for the slag product. Although slag temperatures as low as 1250° C were recorded when melting the RWMC soil, temperatures in excess of 1600° C were necessary to achieve the fluidity required for a successful slag tap.

Jan 1, 1994

By Malsuzaki. Kenji

A mathematical simulation model of the Imperial Smelting Furnace operation has been developed for purpose of improving the furnace operation. The model consists of top, shaft and bottom regions. Analysis in the shaft region is based on differential heat and materials balances taking account of reaction kinetics and heat transfer rates, and those in the top and the bottom regions are based on heat and materials balances under a steady-state condition. Longitudinal distributions of process variables such as temperatures of gas, sinter and coke, gas composition and fractional conversion under a practical operating condition were calculated. With this model, the furnace performance under various operating conditions also can be shown reasonably predicted.

Jan 1, 2003

By Kenji Matsuzaki

A mathematical simulation model of the Imperial Smelting Furnace operation has been developed for purpose of improving the furnace operation. The model consists of top, shaft and bottom regions, Analysis in the shaft region is based on differential heat and materials balances taking account of reaction kinetics and heat transfer rates, and those in the top and the bottom regions are based on heat and materials balances under a steady-state condition, Longitudinal distributions of process variables such as temperatures of gas, sinter and coke, gas composition and fractional conversion under a practical operating condition were calculated, With this model, the furnace performance under various operating conditions also can be shown reasonably predicted,

Jan 1, 2003

By A. A. Hejja

The effect of composition on electrical conductivity, viscosity and liquidus temperature of the slags was investigated in the temperature range of 1300" to 1450°C. The synthetic slags containing CaO, MgO, SiO,, A1,0, and FeO were similar to those employed in the electric furnace smelting of sulphide Cu-Ni concentrates containing PGM (Platinum Group Metals) from the Merensky Reef of South Africa. FeO and SiO, were found to affect the viscosity and conductivity the most while liquidus temperature depended on MgO content in addition to these. The activation energy for electrical conduction was found to vary from 67 to 159 kJ/mol and that for viscosity from 125 to 209 kJ/mol. Optimization of the slag composition was attempted on the basis of opposite trend of the viscosity-electrical conductivity relationship with slag composition.

Jan 1, 1994

By Du Sichen, S. Seetharaman, J. A. Bustnes

"The present study deals with the kinetic studies of reduction of some selected transition metal tungstates with hydrogen. The measurements were carried out by the isothermal thermogravimetric method. Shallow powder beds were employed in order to avoid the effects due to transport phenomena affecting the reaction rate. In this way, the chemical reaction rates could be selectively studied. The experiments were carried out in the temperature range 873 - 1173 K. From the experimental data, the activation energies were evaluated and were found to be around 88 kJ / mol in the case of both iron as well as cobalt tungstates indicating the similarities in W-O bonds in both cases. The activation energies obtained are discussed in the light of the position of the transition metal in the periodic table as well as the thermodynamic stabilities of the various tungstates.IntroductionThe tungsten containing hard metals, characterized by high density, belong to a class of two-phase metal matrix composites. While these types of materials have traditionally found their applications within the defence industry as armour-piercing projectiles, counterbalance in helicopters and military aircrafts, outer casings of hand-grenades, etc., commercial applications for this class of alloys also exist, including radiation shields, penetrators for the oil industry, turbines for turbo-jet engines and a wide range of sports related parts. A possible route to the production of these alloys is to reduce the tungstates such as FeW04, Co W04 and NiW04 using a reductant like hydrogen or carbon monoxide. In order to have a better understanding of the processes involved in the production, it is important to have a knowledge of the reduction kinetics for these tungstates. According to the knowledge of the present authors, while the reduction ofNiW04 by hydrogen gas has been investigated earlier in the present laboratorypl no systematic reduction study has been carried out previously for the tungstates of iron, cobalt."

Jan 1, 1996

By V. Madhusudhan Rao

Fly ash is a finely divide non ? combustible material obtained as a by ? product of coal combustion. It is a major by ? product of coal based thermal power stations. Until recent past it was considered as a waste and highly polluting material. However its formation can only be minimized by using suitable technology in the boilers. In recent past it is found that Fly ash has many end uses and it has proven itself to be a potential construction material. But the suitability of fly ash for various applications largely depends on the amount of unburned carbon, which is turn depends on the firing method. Fly ash samples from various power plants existing in India using a fluidized bed method and pulverized bed were analyzed and a comparison of these two firing methods was carried. This paper deals with the compositional requirements for fly ash used for the fabrication of insulating doors using AAC (Aerated Autoclave Concrete) and the methods employed to make fly ash suitable for this purpose. It also includes the latest ?U? beam technology for effective fly ash recycle. If the by products of coal combustion from power plants like fly ash as the paper stresses are utilized properly, it is not an exaggeration to say that power generation is possible with absolutely zero cost.

Jan 1, 2006

By David Van Aken, Arpana S. Murthy, Simon Lekakh, Von L. Richards

"Three heats of 17-4PH stainless steel: with zero, three percent, and seven percent cobalt addition were melted in a 45kg (1 00lb) induction furnace under argon; and cast into no-bake molds and preheated investment shell molds. Specimens were sealed into quartz tubes under vacuum, and homogenized at 1200°C from 2h to 72h. Computational thermodynamics and optical microscopy were used to predict and characterize the microstructures. The lath martensite packet size and the amount of 8-ferrite were observed to be inversely related. A compromise between decrease in segregation and increase in lath martensite packet size was chosen for the optimum homogenization treatment. The specimens were austenitized, quenched, and characterized for retained austenite using x-ray diffraction. Age hardening kinetics were studied at 454°C (850°F), 468°C (875°F), and 482°C (900°F); and, the activation energies for precipitation of copper were calculated. Tensile properties and Charpy V-notch impact energies were measured in the peak aged condition. Fracture surfaces were observed using scanning electron microscopy and Energy Dispersive Spectroscopy. The addition of cobalt was found to be beneficial for the improvement of strength as well as notch toughness.IntroductionSegregation in the as-cast condition is one of the drawbacks of metal casting. This paper presents a study on the homogenization treatment of 17-4 PH cast stainless steel and the effect of cobalt addition on tensile properties and Charpy V-notch toughness. Lattice dilatation studies show that additions of up to 6% Co to iron has a negligible effect on the lattice parameter, whereas both the modulus of elasticity and shear modulus increase with increasing cobalt additions5• An ordering reaction has been reported in cobalt-containing, maraging steels and contributes to the hardening during ageing1-4• Although, cobalt addition in maraging steels has been extensively researched, and has been reported to be beneficial; it has not been explored much in other age-hardening stainless steel systems. In a previous study, the addition of 3% Co in cast 17-4 PH martensitic age-hardenable steel was found to improve the strength and elongation while maintaining the charpy V-notch toughness6."

Jan 1, 2011

By Yousef Mohassab, Manoranjan Misra, Monalisa Panda, Eman Wahbah

This work studies the removal of arsenic (V), arsenate, and arsenic (III), arsenite, from aqueous solution using calcined Quintinite-3T. The two adsorbents Quintinite-3T was prepared, calcined at different temperatures, and characterized by XRD, BET, and SEM. The surface area of the calcined Quintinite-3T was 193.4 m2/g. The particles size ranged from 12 to 56 nm for the uncalcined Quintinite-3T and from 24 to 42 nm for the calcined Quintinite-3T. Kinetic analysis, adsorption isotherm, and factors affecting the adsorption were investigated. Calcined Quintinite- 3T retained As(v) and did not release it back to water even after an entire month.

Jan 1, 2016

By E. Açma

Sivas-Divrigi flotation plant has a capacity of 90,000 tpy. Beneficiation of the tailings of iron ore magnetic separator seems to be attractive, because of its Cu, Co, and Ni contents. In the experimental work, sulfidic flotation concentrate is produced from these tailings. A roasting-leaching-H2S precipitation procedure is used to treat this concentrate, containing 0.55% Cu, 0.51% Co, 0.74% Ni, and 0.027% Zn. Sulfatizing roasting is carried out in a rotary furnace at 690°C. Roasted product is leached with 10 gpl HzSOl at 70°C and 30% pulp density. For the precipitation of desired metal, H2S is bubbled through the concentrated solution of repeated leaching, under controlled temperature and pH. Final metal recoveries of 91% Cu, 91% Co, and 50% Ni, and 92% Zn are attained. Roasting gases with their 13% SO2 content are suitable for H2SO4 production and the leach residues can be integrated with the iron ore processing plant as they contain 57.4% Fe and very low non-ferrous metals.

Jan 1, 1993

By Masao Miyake, Eiichiro Matsubara, Tetsuji Hirato, Yasuhiro Awakura

"Zn-Cr alloy coating with around 15 wt% Cr has been found to have much higher chemical corrosion-resistance to steel than conventional zinc plating, while· its structure has not been clarified. The Zn-Cr alloy plating is performed at high current densities around 1 A cm-2 and for 10 to 20 sec using acidic aqueous sulfate solutions with some additives in the iron-steel industry. Due to the high current densities, it seems reasonable to consider that the Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings have a non-equilibrium phase and have a structure change in the .direction of thickness. In this research, the crystal structure of the Zn-Cr alloy coating electrodeposited at high current densities and change of the structure in the direction of thickness were examined by X-ray diffraction. The coatings containing under 20 and 35-40 wt% Cr had hcp and bee structure, respectively, while the coatings containing 20-35 wt% Cr comprised two phases with the hcp and the bee structure. The structure of the coating varied in the direction of thickness; both the hcp and bcc phases coexisted in the vicinity of the substrate, while the hcp phase became predominant with increasing distance from the substrate.IntroductionRecently it has been reported that Zn-Cr alloy coating containing around 15 wt% Cr has much higher corrosion-resistance to steel than conventional zinc plating.1-3) The corrosion-resistanc·e of Zn-Cr alloy plated steel sheet with a plating amount of 20 g m·2 is, for example, superior to that of Zn plated steel with a plating amount in the range 60 to 90 g m·2 , which is widely used for automotive bodies today.4l The Zn-Cr alloy plating is obtained by electrodeposition at current densities over 0.5 A cm·2 from a sulfate solution containing zinc and trivalent chromium ions and some additives.5•6) The deposition current densities mentioned above are much higher than those for usual electroplating processes, e.g., Zn, Cu and Ni plating, carried out about 0.05 A cm·2 • Therefore, the time required for plating is very short; around 10-20 sec. Due to the high current densities, it seems reasonable to consider that the· Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings do not have a phase expected from equilibrium diagrams; no phase diagram of the Zn-Cr system with a full composition range has been available. 7). In other words, the alloy phase plated would be a non-equilibrium phase with unknown structures."

Jan 1, 2000

By Gus Van Weert

Hydrometallurgical oxidation of sulphides is capital and energy intensive, with autoclave and bio-technology competing for lowest overall cost status. The use of surface aerators instead of stirred tank reactors could provide lower costs for bio-oxidation of concentrates. With this in mind, the Delft Inclined Plate reactor was designed with inclined plates above a settler shaped reactor to continuously return slurry from the lowest point in the settler to the surface of the liquid. The multiplate superstructure overcomes the scale-up restriction of the standard circular surface aeration patterns. DIP aerator energy and volume requirements for oxygen transfer from air will be presented in terms of kg O2/kWh and kg O2/m3/h transferred as a function of wt % sand in the slurry and compared to stirred tank performance. Scale up from the 4 m3 pilot unit will be discussed.

Jan 1, 1996

By Sylwia Zymankowska-Kumon, Rafal Danko, Mariusz Holtzer, Artur Bobrowski, Michal Kubecki

"Moulding sands with furan resin constitute constantly growing part in technologies of producing castings from iron alloys. Due to the presence of harmful substances in resins such as furfuryl alcohol, phenol and formaldehyde, using those mould sands may be hazardous to the natural environment and workers. The general assessment of harmfulness of sands used for molds and cores encompasses 2 basic points: emission of hazardous substances during processes of preparing sands, pouring mold with liquid metals (high temperatures), cooling and shaking-out; possibility of washing out hazardous substances from used sands to the environment, during storage or economic use outside foundries. We present the results of research on the assessment of harmfulness of mould sands with furan resin in the scope of the above points. The research was conducted according to the original method prepared by the authors, which has been used for years in cooperation with various foundries (Poland, abroad).IntroductionSands are used by the foundry industry to create metalcasting moulds, where the individual sand grains are typically bound using bentonite clay and carbonaceous additives or resins. During the casting process, the moulds can be exposed to temperatures as high as 1500°C depending upon the metal being poured. The molten metal causes thermal decomposition of carbonaceous additives or resins, which results in the formation of potentially hazardous organics that are emitted to the atmosphere and condense in the moulding sand [1]. The moulding sands are reclaimed within the foundry, but part of them are eventually discarded in landfills, because it is not longer suitable to make metalcasting molds [2, 3]."

Jan 1, 2013

By S. G. Kumar

The performance of nickel based high temperature materials is directly related to their microstructure, which is controlled by the various processing steps. Nickel base alloys are melted and refined by a variety of processes that include Vacuum Induction Melting (VIM), Vacuum Arc Remelting (VAR) and Electroslag Remelting (ESR). The limitation of VIM is that the metallrefractory reactions lead to the disintegration of the crucible and hence contamination of the product due to macrosegregation. This macrosegregation is alleviated to some extent by controlling the solidification in VAR. The main attraction of ESR is its ability to produce a clean product by controlling the deleterious inclusions. In recent years Electron Beam Melting (EBM) is emerging as an alternative to the VIM, VAR and ESR. This paper reviews the current status of these processes and outlines the scope for further improvements in the processing technology.

Jan 1, 1993

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid alumina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scaru;ling electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid aluimina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scanning electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003