Search Documents

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of underground and surface operations. The East Ertsberg skarn system (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production from the third lift deep ore zone (DOZ), has reached 80 kt/d (88,000 stpd) during 2010, with this rate sustained through 2015. The orebody was proven below the existing caving level, with the next vertical block called the deep mill level zone (DMLZ).

Jan 1, 2010

By Oluwasegun Samuel Odebiyi, Shaona Wang, Feng Gao, Biao Liu, Hao Du

Recovering vanadium from vanadium titanium-magnetite (VTM) ore using ( NH4)2C2O4 is a clean hydrometallurgical process, but the drawback is the low recovery and slow kinetics due to the formation of inhibitor. A novel energy-efficient mathematical model was derived for green leaching of VTM in which the mechanical activation (MA) removed the inhibitor “δ” (formation of impermeable product layer of CaC2O4) covering the reacting core of the CaV2O6 leaching process in ( NH4)2C2O4 solution. Before the MA processing, the formation of the CaC2O4 layer affects the kinetics (slow) and NH4VO3 leachability (low recovery). The dissolution rate enhancement and economic importance (in terms of leaching kinetic/recovery) of mechanical activation (MA) pretreatment in hydrometallurgical processing cannot be overemphasized. It is shown from the experimental and developed mathematical model results that the rotating speed of the ball mill (ωb) has a significant effect on the NH4VO3 recovery. At 360 rpm, the experimental result gave an 82% optimum recovery rate and a reaction rate constant of 0.01889s−1 with close correlation with the present models at 82.8% and 81% for liquid-to-solid layer diffusion and chemical reaction controls, respectively, with a reaction rate constant of 0.018883s−1. The close correlation between the experimental recovery rate results and the diffusion recovery rate model result justifies that the leaching process is diffusion control shrinking core kinetic with experimentally measured activation energy (Ea) value of 19.502 kJ/mol . This present model proved that MA enhances the dissolution rate regardless of the formation of a passivation layer on the material and best describes the kinetics of the MA hydrometallurgical processes compared to the shrinking core model.

Nov 3, 2023

By Mark J. Zdunczyk

"The term “aggregate” has a number of definitions depending primarily on the use of the material. Aggregate in some context is sand, gravel, crushed stone, slag or other material of mineral composition used in bituminous and portland cement concrete, mortar, plaster, railroad ballast, filter beds and a variety of other uses where aggregates can be utilized.Of the natural aggregates, crushed stone is widely used for most construction purposes. Crushed stone can be mined from a variety of rock types such as limestone, dolomite (dolostone), granites, and granitic type rocks, basalt, gabbro (trap rock), sandstones, schist, marble, gneiss, quartzite, rhyolite, as well as other rock types. The U.S. Geological Survey (USGS) breaks down the rocks by type sold as follows: limestone, dolomite, marble, calcareous marl, shell, granite, trap rock (basalt, diorite) sandstone/quartzite, slate, volcanic cinder and scoria and miscellaneous stone.In 2015, the USGS estimates that 1.32 Gt (1.45 billion st) of crushed stone were produced in the United States. The volume of crushed stone produced, and the numerous mines that produce it make the crushed stone industry the largest mining industry in the United States. The five leading states for production of crushed stone in 2015 were Texas, Pennsylvania, Missouri, Florida and Ohio. The size of the first two states certainly helps in output because of the large market area. The remaining states benefit from being able to barge along rivers to outside markets in adjoining states. Georgia producers rail large amounts of granitic aggregate to Florida and adjacent states devoid of crushed stone aggregate, especially skid resistant aggregate (aggregate used on the top course of asphalt roads)."

Jul 1, 2016

By Yucheng Li, De Huang, Yonghong Liu

Mine frictional resistance is one of the essential parameters of mine ventilation systems, and it is of considerable significance for the prevention and control of mine risks and accident hazards. Frictional resistance requires a lot of resources and time and has errors. To reduce the errors of frictional resistance, a regression model of frictional resistance is proposed based on the correlation analysis of the affecting factors. Through the comparative test analysis of seven regression methods, it is found that the classification and regression tree method for solving the proposed regression model has better performance than other methods. The least square error criterion is used to calculate and rank the importance of the factors affecting frictional resistance. The results show that the cross-sectional area of the tunnel, the support method, and the presence or absence of devices or pedestrian ladders have the most considerable influence on the prediction accuracy of frictional resistance. The support methods and cross-sectional areas are essential input variables. Through the combination test analysis of the influencing factors, the results show that the regression model does not have predictive ability when the number of input variables is less than 3 and the best predictive performance cannot be obtained using all the influencing factors. The best prediction model of resistance is to combine the shape of the tunnel, the support method, the presence or absence of devices or pedestrian ladders, and the cross-sectional area. The method proposed in this paper does not require a lot of resources and time investment, and the frictional resistance error is small. At the same time, it solves the problem of resistance prediction with incomplete data of influencing factors and provides a compelling new method for obtaining frictional resistance parameters.

Jan 28, 2022

By Michael Gobla

"Since 1994 the Bureau of Reclamation (BOR) has used risk analysis to evaluate dams. Risk considers both the likelihood of failure and the expected consequences should failure occur. Risk analysis relies on the detailed formulation and critical analysis of all possible potential failure modes. Potential failure modes are formulated by describing the sequence of events that must occur to result in failure, where failure is defined as the uncontrolled release of the impounded reservoir. Failure occurs in response to loadings such as water seepage through a dam (static forces), shaking from an earthquake (dynamic forces), sudden flood inflows (hydrologic forces), or accidental overfilling (operational errors). Reclamation has, to a limited extent, applied risk analysis to inactive and abandoned mines to evaluate tailings dams, pit lakes and flooded underground mines. Case histories of potential failure mode analysis, as applied to mine impounded water, illustrate what critical technical information is needed to determine if failure is likely, what the consequences of failure are likely to be, and what are the highest risks that should be addressed first.IntroductionImpounded water and high water content wastes at mining and industrial processing sites are potential threats to public safety and the environment. Recent failures such as the TVA Kingston flyash impoundment failure in Tennessee in 2008 (4.1 million m3 or 5.4 million cu yd) release, the Mt. Poly Tailings Dam failure in British Columbia in 2014 (4.4 million m3 or 5.8 million cu yd) release, and the Samarco Fundao Tailings Dam failure in Brazil in 2015 (59 millon m3 or 78 million cu yd) release have renewed attention to this issue. Potential risks from impounded water at mining and industrial sites originate not only from tailing dams, but also from water in process ponds and conveyance pipelines, sediment retention dams, water retention dams, mine pit lakes and flooded underground mine workings.Conventional water retaining dams also have a record of failure. Notable examples of failure include Vajont Dam in Italy in 1963 (2,600 lives lost), Banqiao and Shimantan Dams in China in 1975 (171,000 lives lost), and Machhu-II Dam in India (10,000 lives lost). After the 1976 Teton Dam failure in Idaho, the U.S. Bureau of Reclamation (BOR) established a Dam Safety Program. By 1984, the agency developed and began using risk analysis methods. BOR operates and maintains an inventory of hundreds of aging dams which were designed and constructed over a period of 100 years. Many of these facilities were designed and constructed prior to the development and adaptation of modern soil mechanics in dam engineering. Diligent observational monitoring, detailed site investigations and the application of risk evaluation to the BOR dam inventory has identified many deficiencies resulting in significant demands on available funding for remediation efforts. The application of risk analysis has allowed the agency to rank sites by risk. By giving priority of remedial efforts to high-risk sites, significant improvements to dam safety have been achieved."

Dec 1, 2016

By James M. Barker

No commodity agreements now exist for sulfur and a lack of reference to sulfur commodity agreements exists in the literature. Law (1975) made a passing reference to sulfur as one of a group of commodities where "there have been additional control efforts of various types." Clearly, sulfur was a candidate, at least conceptually in the past, for some form of commodity agreement and the following discussion centers on the world sulfur market of the early 1980's in this context. GENERAL THEORY OF COMMODITY AGREEMENTS The upsurge in demands for commodity agreements seen in the last decade or so stems largely from agitation by the less developed countries (LDC) for better economic treatment by more developed countries (MDC). Several economic factors, real or imagined, adversely affect the LDC's as follows (MacAvoy, 1977): 1) variable demand in MDC's causes wide fluctuations in commodity prices which hurt the economies of commodity producers, who are often LDC's although consumer economies may also benefit from more predictable prices; 2) a general decline of commodity prices relative to the price of manufactured goods which hurts commodity producers in their balance of trade while their stocks and overcapacity rise; 3) instability of LDC economies enhanced by the above factors lowers internal stability, inhibits foreign investment, and retards economic growth; and 4) a lack of self respect when dealing with developed countries o, following the OPEC lead, LDC producers want the stature related to cartel market power.

Jan 1, 1985

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By C. G. Clifton

The Oatman District produced approximately 2.2 x 10 6 ounces of gold and 0.8 x 10 ounces of silver between 1897 and 1942. A total of 3.8 x 10 tons of ore averaging 0.58 O/T gold and 0.17 O/T silver was extracted from eight major orebodies and a number of lesser deposits. Oatman lies at the center of a trachyte-latite-rhyolite volcanic complex which contains at least one resurgent caldera. The orebodies are typical epithermal quartz-calcite + adularia lode deposits which are very deficient in sulfur. Ore deposition has occurred within dilatant zones on faults which radiate from a common point within-the complex. Fischer-Watt Mining approached the Oatman District with an integrated exploration program utilizing four basic procedures to define the characteristics of past productive areas the results of which were applied to unexplored portions of the vein system. These procedures, listed in their order of usefulness, in defining known and prospective mineralized zones are: vein contouring, detailed alteration mapping, fluid inclusion temperature determinations, and geochemical sampling.

Jan 1, 1980

By J. M. Wood

Green algae have been found to be much more resistant to heavy metals than blue-green algae. Several mechanisms for resistance to toxicity have been recognized in laboratory strains of Cyanidium, Chlorella and Chlamycomonas. Cyanidium and Chlorella both grow at low pH in acid mine water. Cyanidium removes metal ions from solution by precipitation as metal sulfides whereas Chlorella complexes metal ions to the cell surface i.e. cell wall) and therefore functions as an efficient ion exchange vehicle. We have shown that Ca2+, Mg2+, K+ and Na+ are of critical importance in both the resistance and bioaccumulation of toxic heavy metals.

Jan 1, 1986

By W. Missildine, J. K. Hrica, I. Benbourenane, T. J. Orr, J. L. Bellanca

Each year, haul truck accidents account for a large portion of mining injuries and fatalities. To better understand why these accidents continue to occur, researchers from the National Institute for Occupational Safety and Health (NIOSH) utilized a cognitive task analysis methodology to identify the user requirements of surface haul truck operators and assess differences in perceptions between operators, managers, health and safety professionals, trainers, and maintenance personnel. Additionally, researchers used the critical decision method to focus on better understanding the cognitive demands, decision-making, and problem solving during nonroutine incidents. The preliminary results of this study identify and explore themes within the broad categories of hazards, skills & expertise, and training and provide detailed accounts of nonroutine incidents such as near-misses, loss of control, and collisions. These accounts reveal insights into operator decision making and event progressions that can then be used to build more realistic training scenarios and address hidden hazards and root causes of these incidents. These results, along with potential solutions offered by study participants, can inform future research and help identify creative interventions that can be used by mine operators to address haul truck safety issues

Mar 2, 2022

By Maryam Motamed, Jeremy Stone, Leigh Anne Zhang

Controlling and predicting ground movements are essential to the design of shoring systems. The Courthouse Commons tunnel in San Diego, California, included a 56-foot-deep temporary shaft as a launching point for tunneling using the Sequential Excavation Method (SEM). The rectangular shaft was unique in that it was surcharged on one wall by an 11-story building and employed a hybrid support of excavation design. An array of geotechnical instrumentation was used to monitor lateral and vertical movements at the ground surface. This paper compares the measured ground movement with the predicted ground movement from various excavation stages

Dec 1, 2022

By Xiaozhen Song, Ashish Ranjan Kumar, Shimin Liu

To investigate the influence of boreholes, fans, and curtains for large opening underground mines (LOUM), we conducted a field survey for LOUM with the survey data serving as the numerical modeling inputs using computational fluid dynamics (CFD) models. Five different CFD modeling results were obtained with different borehole, box fan, and curtain setting conditions. The results indicate that most air quantity directly escapes through outlet 1 after coming into the inlet, causing a huge loss of airflow; volumetric air exchange index (VAEI) and minimum hours of fully exchanging the air (MHFEA) measure air exchange efficiency, with zone 2 of case 5 having the highest VAEI; The borehole minimally affects zones 2, 3, and 4, but drastically alters airflow direction in zone 1; The box fan enhances airflow to zone 2, improving ventilation efficiency and increasing VAEI; Curtains have little effect on distant working faces but influence airflow near inlets and outlets. This study provides a foundation for future research on the influence of boreholes, fans, and curtains, as well as optimizing their placement and effectiveness in face ventilation.

Feb 22, 2026

By Ross K. Digby

The Victorian Tunnelling Centre (VTC) has evolved its purpose from purely training workers, to a tunnelling industry education city. The VTC has now focused its activities on the areas of technology; education and training; applied research; and career education. were identied as the hus around which activities would e conducted to create a tunnelling industry education city. The VTC provides ustralias tunnelling industry with an education facility that not only provides laour training, ut enales the industry to come together to meet, participate in product launches, undertake research, work with new technologies and promote tunnelling careers.

Jun 23, 2024

By William J. Almas

Operating uranium mill tailings containment and mill decommissioning activities are regulated by the Nuclear Regulatory Commission (NRC) and the Environmental Protection Agency (EPA) through numerous regulatory mechanisms. Reduction of radon emissions from tailings disposal areas, remedial actions to return groundwater to baseline constituent concentrations, and 200-to 1,000-year stabilization of tailings are major focus areas of regulation. The cumulative economic impact and uncertainty associated with regulation are very significant and will hinder future development of uranium milling facilities.

Jan 1, 1991

By A. M. Anthony, A. Y. Atta, S. S. Magaji, U. Abubakar-Zaria

There are two major gold recovery methods: the hydrometallurgical technique, which employs cyanide solutions, and amalgamation method, which involves mercury (Hg). These methods present considerable health, safety, and environmental concerns. Past applications of alpha-cyclodextrin (α-CD) on gold scraps show that α-CD is not only inexpensive, but is also environmentally friendly. This research work used α-CD to recover gold from gold ores instead of gold scraps. The gold ore was sourced from Shanono gold deposit site Kano State,Nigeria. The gold ore was characterized by fire assay (FA) for the precious metal. The concentrate was digested with aqua regia (AR) for 24 h. Modified AR, where hydrochloric acid was replaced with hydrobromic acid, was used for the gold digestion due to the good match in molecular recognition between gold bromide ion (AuBr)− and α- CD in a second sphere coordination complex. The digestate was characterized using atomic absorption spectroscopy (AAS). Gold recovery using this technique is pH sensitive, and five pH values (2.0, 3.6, 4.0, 5.4, and 6.0) were investigated. FA analysis showed the Shanono gold ore deposit contains an average of 4.71 ppm of gold, AAS analysis showed highest gold recovery of 69% at pH 4.0, which is lower than recoveries from the metal scraps. This could be due to the presence of other gangue minerals closely associated with the ore. However, gold recovery using α-CD on Shanono gold ore has shown to have a higher yield of 69% compared to 35.5% yield obtainable by Artisan Small Scale Miners using mercury.

May 5, 2020

By Ping Zhang, Shahram Mozaffari, Andreas Ylmefors

The risk associated with mining induced seismicity and the related rock bursts has become one of the major threats to the safety and sustainability of mining at the Kiirunavaara mine. The causes of mining induced seismicity at the Kiirunavaara mine are very complex and have affected our understanding on the source mechanisms of seismicity and further the mitigation of the seismic risk. Detailed analysis of historical mining induced seismicity at the Kiirunavaara mine was conducted. The focus of this analysis was placed on the classification of large seismic events and the evaluation of the influential factors on the classified seismic events. 145 events with local magnitude larger than 1.5 that occurred between January 1, 2011 and March 31, 2021 were analyzed. For this analysis, seismic events located in the hanging wall were not included, as these have not been observed to cause large damages to the mine itself. It was found that the magnitude of the events had good correlation with the stress change in relation to the production location. The seismic events were classified as mining-front associated, ore-pass associated, mining-front and ore-pass associated and others, according to their hypocenter location. Most of the mining-front associated events, concentrated around the production levels and slightly above and below them, generally correlated with shear cracks, and most of them occurred when the ore flow between two production levels started. The numerical modelling showed that slip of the geological discontinuity, due to unclamping between hanging wall and footwall, could be the major causative mechanisms, which further supports this finding. The ore-pass associated events are located close to the ore passes. Large seismic events located between ore passes have the source mechanism of both fault-slip and non-shear, but events located at the outer side of ore passes were all fault-slip type. By checking with the ore pass scanning data, it was concluded that the most of the events located between ore passes could be pillar bursts. An elastic core concept has been then used to define a critical pillar width. The paper is not intended to be prescriptive but rather to initiate discussion of the possible classification of seismic events at the Kiirunavaara mine and to present new perspectives of the causes of the seismicity for improving the present seismic risk management.

Apr 26, 2022

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice pitwall profiles are often planar in crosssection and the profile in between ramps especially tend to be planar and defined by a constant inter-ramp angle. Sometimes rock layers exhibiting different strengths require the inclination of the profile to vary with depth, but the inclination across each layer is usually constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and Factor of Safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e. the planar profiles exhibiting the same FoS) up to 8 degrees depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Mar 2, 2022

By Mohammed Sakr

The empirical relationship between torque measured during installation and pile capacity has gained a wide acceptance in the helical pile industry in the last few decades. This paper presents a theoretical model developed to estimate torsional resistance of cohesive soils to helical pile installation. The proposed torsional resistance model was then used to establish torque factor, Kt, a factor that is widely used in the industry. The results of the study indicated that the Kt factor is a function of the load path (i.e. tension or compression), pile geometry and soil properties. The assessed Kt factors in tension and compression were validated by the results of 74 installation records and full-scale helical pile load tests. A parametric study was also performed to qualitatively assess the relative importance of different parameters that affect the Kt factors.

Aug 1, 2013