Search Documents

By Lloyd A. Morley, Robert Stefanko

Before going directly to the analysis, it would be good to summar¬ize explosion-proof container approval methods. Both Magison (52) and Short (84) state that in general practice, the systems are certified for: 1. a rugged enclosure able to withstand an internal explosion but not allow explosively hot gases to escape, and 2. maximum surface temperature, with equipment operating inside, that will not ignite the surrounding atmosphere. Also, testing insures that any material in contact with the container surface will not be ignited by a hot spot. Associated with the first practice, the enclosures are inspected for: 1. a safe flange gap width, 2. a pressure increase during ignition, and 3. an hydrostatic pressure withstand level. The hydrostatic pressure level is almost always determined by a meas¬ured ignition-pressure test and is usually applied to prove the mechan¬ical design to some safety factor. Consequently, explosion-proof enclosure testing includes temper¬ature, permissible flame gap, and pressure. Specifications and prev¬ious research also can be similarly separated even though some interre¬lation exists between the flame gap size and internal enclosure pressure during an explosion. The Schedule 2G Sections applicable to these subjects are: 1. 18.2 Definitions; 2. 18.6 Applications;

Jan 1, 1974

By Leland A. Yerkes

Refining aluminum from crude aluminum alloys by the subhalide reaction was investigated to develop a method of producing aluminum by means other than electrolysis of its oxide. The best materials and design for the apparatus and also optimum operating conditions, including temperature, pressure, vapor flow rate, and composition of alloy charge were studied. In the subhalide process, aluminum-trihalide vapor reacts with aluminum in the alloy under high temperature and low pressure, forming volatile aluminum monohalide which reverts to aluminum metal and aluminum trihalide on cooling. The only halide used in this investigation was aluminum trichloride. The crude aluminum-silicon alloys used as the principal raw material contained from 21.9 to 36 percent aluminum, and significant quantities of iron and titanium. These alloys were produced by direct electric smelting of clays. Graphite tubing that was heated by an induction coil proved to be satisfactory material for the laboratory reactor chamber, Enclosed in an insulated glass or quartz pipe, the reactor was used in both vertical and horizontal positions with various baffle and tray arrangements for directing the trihalide vapor both over and through the alloy. Aluminum trichloride vapor was generated in the sublimer at one end of the glass pipe, passed into the reactor where contact was made with the crude alloy, and aluminum monochloride gas was formed. When the gaseous mixture of aluminum monochloride and unreacted tri-chloride passed out of the reactor and entered the condenser, the gases were cooled to 900° C. or less, causing the monochloride to disproportionate into aluminum and aluminum trichloride vapor. The aluminum was deposited on the condenser walls while the aluminum trichloride vapor was carried out of the condenser and into the opposite end of the glass pipe where it solidified on the cooled copper coils.

Jan 1, 1961

By V. F. Parry, W. S. Landers

"INTRODUCTION The primary object of this investigation was to determine changes in physical and chemical properties of subbituminous lump coal while in storage for 8 months in a typical residence and to demonstrate how this fuel may be stored without degradation or spontaneous combustion. The second object of the study was to determine how the stored coal performed in a hand-fired furnace operated under practical conditions.The investigation revealed that if care is exercised in placing sub-bituminous lump coal in a closed bin, no significant slacking or degrada¬tion occurs, no hazards arise, and over-all indicated efficiencies of about 65 to 69 percent can be obtained under practical,firing conditions that the average home owner can meet.Owing to the war emergency, much attention is being given to the proper storage of coal, and campaigns are being conducted to increase the quantity of coal being stored to relieve transportation and production overloads. Ordinarily, coal dealers do not recommend storage of subbituminous coal in homes owing to deterioration of the coal and to possible hazards from spontaneous combustion. This practice has grown from some troubles that have been experienced, which can be traced to improper preparation, improper bins, and poor technique in placing coal in a bin. There is no good reason why subbiturninous lump coal cannot be stored safely in homes."

Jun 1, 1944

By John D. Sullivan

The recovery of copper by leaching from relatively low grade ores containing both oxidized and sulphide minerals is rapidly gaining in commercial importance. There is an economic limit below which certain ores can not be treated by concentration methods, and material with values below this limit must be discarded, possibly to be treated later, or the copper must be extracted by wet processes. Heap leaching has been carried out by the Phelps Dodge Corporation, Copper Queen Branch, for several years, and to-day its plant is a large producing unit. The Ohio Copper Coy at Bingham, Utah; has been leaching in place since 1919. Many other leaching operations are also being; carried out in various parts of the United States and in foreign countries. The plant at Rio Tinto, Spain, may be considered the father of heap leaching.

Jan 1, 1931

By David C. Byrne

From an engineering perspective an ideal industrial noise control solution focuses directly on the actual source of the poise. Eliminating the noise-generating mechanism altogether obviates the need for other noise contra l treatments or hearing protection devices. However, in cases where attenuating the source is not feasible engineering controls must be oriented toward blocking the path that the sound waves travel toward employees. Acoustical enclosures are commonly used as sound path treatments to contain the noise from a machine: alternatively a control room/booth or equipment operator's cab may be used to isolate the worker from the noise. Anyone who has successfully used acoustical enclosures knows that the design procurement, and installation process is deceptively simple. Alt too often First-time efforts fait to account for many of the constraints that can render the enclosure essentially useless. Things that cannot be overlooked include: providing convenient worker access (physical and visual): allowing for proper machine operation/product flow; and supplying fresh air or preventing undue heat or contaminate build-up inside the enclosure. All of these factors must be given careful consideration, otherwise the enclosure will not perform adequately.

By Neil B. Young

Carbonate minerals constitute a major fraction of the oil shale in Colorado's Green River Formation. Quantification of carbonate minerals is important for the characterization of oil shale, particularly because of their thermal activity in production of oil from shale. The carbonate minerals found in this oil shale are nahcolite (NaHCO3), dawsonite [NaA1(OH)2CO3], dolomite [(Mg1-xFx)Ca(CO3)2], calcite (CaCO3), and ferroan [(Mg1-xFex)CO3]. Although carbonate minerals can be removed by acid extraction from the balance of the oil shale, direct determination of carbonate minerals is complicated by the occurrence of the same cations in more than one mineral. A method for assigning the acid-soluble cations to the individual carbonate minerals was developed from two assumptions based on oil shale geochemistry: (1) Calcite and ferroan do not occur together, and (2) the ratio of iron and magnesium is the same in dolomite and ferroan. These assumptions were tested by the Bureau of Mines by applying the technique for assigning cations to 219 samples from the saline section of the formation. The reported carbonate mineral amounts were compared statistically with X-ray diffraction peak heights, verifying the cation assignment method.

Jan 1, 1975

By Daniel Edelstein

Demand for arsenic trioxide dropped markedly during 1983, primarily as a result of a 27% reduction in cotton planting. As an oversupply of arsenic trioxide developed, prices declined for both domestic and imported material. Domestic Data Coverage.-Commercial-grade arsenic trioxide and arsenic metal were produced by only one U.S. company, which voluntarily reported its production to the Bureau of Mines. To prevent disclosure of proprietary data, the production data have been withheld.

Jan 1, 1984

By Peter J. Clarke

Development of the mineral and energy resources of Afghanistan appeared to be a top priority of the Soviet-controlled Government in the country. In the Afghan Government's plan for 1980-81, the largest allocation in the development budget was for mines, industry, and energy (46.7%). In contrast, only 23.1% of the budget was allocated for agricultural development, despite the fact that the great majority of the population was dependent on farming. The mineral industry of Afghanistan consisted of the production of natural gas, cement, coal, fertilizer materials, and rock salt. Production levels for all of these commodities were down an average of 45% from those of 1978, before the Soviet invasion. Prior to the invasion, small quantities of asbestos, barite, and talc had been produced along with about 6,000 to 7,000 kilograms per year of lapis lazuli, a semiprecious gem stone. Afghanistan had supplied about 80% of the world's output of lapis lazuli. Following direct Soviet intervention, production of these minerals declined to near zero.

Jan 1, 1983

By W. W. Adams

Reports received by the Bureau of Mines, Department of Commerce, from State mine inspectors, for November, 1930, showed that 219 men were killed in the coal mines of the United States during the month, an increase of 25 over the previous month and 33 over November, 1929. On the other hand the production of coal decreased, the output of 43,329,000 tons in November being 8,397,000 tons less than in October and 9,005,000 tone less than in November a year ago. The larger number of fatalities accompanied by a smaller output of coal resulted in a higher death rate4 per million tons in November than in the same month last year or in October, 1930. The November rate was 5.05, as compared with 3.55 for November, 1929 and 3.75 for October, 1930. The increase in the rate for the industry as a whole was chargeable entirely to bituminous mines, as the anthracite mines had fewer fatalities in November than in either of the previous months to which reference has been made. Reports for bituminous mines alone showed that accidents at this class of mines resulted in a death rate of 5.12, based on 195 fatalities and a production of 38,122,000 tons. This rate indicated an increase of 55 per cent over the rate for October, of the same year, and 72 per cent over the rate for November, 1929. The October record was 146 fatalities and 44,150,000 tons, and that for November a year ago was 138 deaths and a production of 46,514,000 tons.

Jan 1, 1930

By J. D. Dixon

The Bureau of Mines investigated the principles of support-rock interaction, based on structural matrix methods which permit mathematical formulation of the problem and computer solution. The principles are given under two main sections: the first discusses the idealization of the tunnel support structural system for matrix analysis; the latter discusses the analysis procedures necessary for carrying out the solution. A general frame matrix computer program and a medium-size computer should be sufficient for carrying out the procedures involved. The example problem consists of a circular tunnel support which is subjected to a uniformly distributed vertical load, Three wall thickness-radius ratios are studied in combination with four support-rock modulus ratios. This problem illustrates the main procedures of the support-rock interaction analysis involved, and examination of the results reveals the influence of the relative rigidities of the support and the rock.

Jan 1, 1971

By Richard A. Thomas, Michael J. Sapko, Gary L. Mowrey, William D. Monaghan, Michael A. Trevits

Over the years, more than 20,000 mine seals have been erected in underground coal mines in the United States. Seals are used extensively in underground mines to isolate worked-out areas, active mine fire zones, and to control water inundations. Seals are most often built directly in the mine and can be fabricated from blocks made of wood or cementitious material. Recently, several explosions occurred within sealed areas of underground U.S. coal mines. These explosions, believed to be initiated by lightning strikes on the surface, destroyed numerous seals and caused considerable damage external to the sealed area. The National Institute for Occupational Safety and Health is conducting research to develop design guidelines, to investigate noninvasive techniques to characterize seal strength properties, and to evaluate seal test methods. As part of this work, a 30-ft wide, 16.1-ft tall and 4-ft thick seal was built in an underground experimental mine using cement and foamed water. Two types of noninvasive techniques are currently being investigated, namely the Schmidt Hammer for measuring compressive strength and ground penetrating radar (GPR) for detecting the presence of anomalies (e.g., voids, discontinuities) within the seal. Once these noninvasive tests were completed, the seal was subjected to destructive explosion testing. This study presents the results of the Schmidt Hammer tests, GPR scans, and the characteristics of seal failure during explosion testing.

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.

By Frank E. Cash

"INTRODUCTION The producing iron-ore ranges in the Lake Superior district are the Marquette and Menominee in Michigan, the Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. The accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year owing to stockpiling underground ore during the winter, or nonshipping, season but closely approximate each other over a period of years. This information circular supplements, combines, and continues the data contained in Information Circulars 7321 3/ and 7410 4/, including statistics for 1946 and 1947.Whereas the title ""Accident Experience"" is used for uniformity and logical indexing throughout this report, ""injury"" will be used as a general term to apply to disabilities of all degrees.During the 8-year period 1940 to 1947, inclusive, 619,054,023 long tons of iron ore was shipped from the Lake Superior district. 5/ Michigan and Wisconsin shipped 117,828,939 tons, or 19.03 percent of the total, and employed approximately 9,260 men. Minnesota shipped 501,225,084 tons, or 80.97 percent of the total, and employed an approximate annual average of 12,260 men. The tons produced and shipped per man employed in Minnesota is much greater than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jun 1, 1949

During the summer of 1973 we were asked to perform a theoretical investigation of the propagation of low frequency (LF) radio waves down deep (10,000 feet) hoistshafts* for the case where the hoist cable ("rope") is the only metal conductor present. Propagation is by means of the TEM coaxial mode of transmission in which the hoist cable serves as the inner conductor and the surrounding rock acts as the outer conductor. Since the rock is a relatively poor electrical conductor the current in the outer conductor of the coaxial line is not confined to a very thin surface layer as in a metal coaxial cable, but spreads radially to a distance that is generally many times the shaft diameter. This feature of the wave propagation requires a more sophisticated theoretical treatment than the approximate skin-depth theory that is adequate for metal coaxial lines. In this Part we treat the hoist shaft wave propagation loss, characteristic impedance, and the field current distributions in the surrounding rock medium. We also show that the large penetration of the wave into the rock outer conductor does not present a difficult problem with regard to coupling the transmitter or receiver to the transmission line with a minimum of insertion loss, but that the large impedance mismatch caused by the capacitance termination between the cage and shaft wall may well be the most significant contribution to overall system loss. Inductive coupling and impedance matching to the hoist rope/shaft transmission line are also treated briefly. Preliminary results indicate that a broad minimum in overall system loss should occur between 100 kHz and 1 MHz, possibly centered around 300 kHz. Further work is needed to better quantify this signal loss behavior, compare it with hoist shaft electromagnetic noise spectral data recently acquired by NBS, and identify the most favorable operating frequencies.

Jan 1, 1974

By Joseph A. Perry

One goal of the Bureau of Mines is to develop technology tp insure a dependable supply of minerals to the United States. To support this goal, the Bureau's Albany Research Center has modified a commercial atomic absorption spectrophotometer to rapidly determine trace levels of mercury by cold-vapor atomic absorption spectrophotometry. Such diverse materials as ores, mill products, stream water, sediments, and flue dust have been analyzed. A very high dynamic range of 0.2 ng/ml to 1 µg/ml of mercury in solutions is routinely analyzed by this instrument.

Jan 1, 1981

By A. Sainato, S. J. Kravits, G. L. Finfinger

This Bureau of Mines report describes and compares the procedures, capital investments, and operating costs of rotary and in-hole motor drilling techniques used to drain methane gas from the Pittsburgh Coal- bed in an underground mine located in southwestern Pennsylvania. A timestudy was conducted during the drilling of each of two boreholes, and the data were collated to serve as a base for comparing drilling procedures and operating costs. Findings indicate that drilling with an in-hole motor offers four advantages over rotary drilling; namely, an increase in drilling productivity, fewer worker-hours required, ease of maintaining vertical and horizontal bit trajectory, and less expensive drilling cost per foot of borehole.

Jan 1, 1985

By Peter H. Toepfer

This report presents the factual data obtained by the Bureau of Mines during diamond-drilling investigation of the Sunset copper deposit in the Index mining district, Snohomish County, Wash. The Sunset mine, first produced copper ore in 1902, but its main period of activity was from 1923 through 1930, The mine has produced 263,500 tons of ore, from which 1,500 ounces of gold, 156,000 ounces of silver, and 12,912,000 bounds of copper-were recovered. The mine has, been idle since 1946

Jan 1, 1953

By K. C. Dean

During investigation of the occurrence of manganese deposits in the western United States, examining engineers of the Bureau of Mines collected samples from several properties in Montana. Extensive laboratory tests were made to determine the amenability of these ores to standard ore-dressing methods of concentration to produce marketable-grade products. The Tzarena claim, one of the properties sampled, is on the western end of the Rama or Black Chief vein in the city of Butte, Silver Bow County, Mont., on the southwestern periphery of the mining district. The Black Chief 'WAR system contains one of the largest and most extensive known rhodochrosite deposits in the world. Test work was conducted on two samples of Tzarena ore. Sample 1 is representative of a vain 5 feet wide on the 150-foot level of the Tzarena shaft. Sample 2 is representative of a vein 8 feet wide in the 100-foot level of the shaft. The Minnie Jane mine, 1/2 mile northwest of the Tzarena claim, contains ore similar in mineralogical composition to Tzarena ore but differing materially in manganese content and to some extent in physical characteristics. Ore-dressing investigations were made on three samples of Minnie Jane ore. Sample 1 represented stock-piled ore, sample 2 represented ore from Minnie Jane mine having a considerable sulfide content, and sample 3 represented low-grade ore.

Jan 1, 1951

By John W. Chandler

The property of the lava Cap Gold: Mining Corporation is in the Nevada City-Grass Valley mining district about 5 miles east of Crass Valley, Calif. At present (July 1940) the plant is mining end milling about 390 tons of gold-silver ore a day; about 310 men are employed. This paper describes the mining methods used and presents mining costs for 1939, when 60,704 tons were mined by cut-and-fill stoping and 55,676 tons by square-setting.

Jan 1, 1941

To develop a magnetic levitation transport system that can reduce the cost and improve safety in transporting coal from the face of underground coal mines to the surface. Background Many conventional mining operations use conveyor belts to transport coal from an underground face to the surface of the mine. The Mag-Lev Transport System design replaces conveyor belts with magnetically levitated coal haulage containers moving through a dedicated pipe¬line. Cost estimates, based on current design data, show the Mag-Lev Transport System would have operating and capital costs that are less than or equal to those of an equivalent-capacity conveyor belt system. The safety hazards associated with conveyor belt systems include exposure to moving parts and pinch points, potential fire hazards due to mechanical friction, and the exposure of miners to respirable dust. These hazards would be eliminated or significantly reduced by this novel technology. Approach The Mag-Lev Transport System uses magnetic levitation technology that allows noncontact, frictionless conveyance of a levitated body within a dedicated transit corridor. The mag-lev technology utilizes two types of permanent magnets coupled with an electronic position control system to achieve noncontact levitation. Levitation is provided by neodymium-iron boron (NdFeB) magnets mounted in the base of the haulage containers and inexpensive ceramic-5 magnets located in the bed of the transit corridor. An electronic position control system is used to overcome the inherent instability of the repelling permanent magnets. Proximity sensors, a signal processing circuit, electromagnetic actuators, and fixed ferrous side rails are the major components of the positioning system.

Jan 1, 1994