Search Documents

By Lawrence Melis

Fission Uranium Corp.’s Triple R Uranium Deposit at its Patterson Lake South Project is located in northwest Saskatchewan in Canada’s Athabasca Basin. As part of pre-feasibility studies for the project a detailed metallurgical test program was completed to provide process design criteria. The testwork program encompassed preparation and analysis of test composites, comminution testing, uranium acid leaching, liquid-solid separation, solvent extraction of uranium, precipitation of uranium yellowcake products, tailings and effluent treatment, tailings physical and chemical characterization, and environmental testing of prepared tailings, as well as investigations of gold and silver recovery from the mineralization. The paper provides mineralogical information, testwork methodologies and test results which were used to arrive at process design criteria and the selection of the process flowsheet for the project.

Jan 1, 2020

By Jan Kvinge, Aina Opsal Bakke, Yanjun Li, Jan-Ove Løland, Svein Jørgensen

"Compound casting is a very attractive approach to reduce the weight of components for some specific applications while keep both the functional and the mechanical property requirements. In this work, Al-7Si-Mg alloy /copper compound castings were produced through a low pressure die casting process. To reduce the oxide present in the interface, flux coating of the copper pipes was tested. The interface layer formed between the two alloys was investigated using Optical Microscopy (OM), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Vickers Micro-hardness was also measured across the interface. Results showed that the flux coating prevented the formation of the metallic bond between copper and aluminum. Instead, high concentrations of potassium, magnesium and fluoride, coinciding with formation of KMgF3 and MgF2, were detected in the interface. In the castings without surface treatment, a continuous metallurgical bond was achieved. In the bond layer, various Al-Cu intermetallic phases have been detected. In addition, formation of primary silicon particles in the reaction layer was observed in all castings. The mechanism for the formation of the intermetallic phases and the strength of the interface layer have been discussed.INTRODUCTION Recent development in the automotive industry has focused on producing lightweight components, which can reduce CO2 emission and increase the efficiency. Often, one material alone is not able to meet the requirements for a specific use. The need for lightweight bimetallic components has therefore increased. Aluminum-copper bimetallic components can be used in wires and bus bars where conductivity is an important factor (Lee, Bang, & Jung, 2005). Compared to Al-Cu alloys, Al-Cu bimetallic components can reduce both weight and cost without reducing electrical and thermal conductivity (Sheng, Yang, Xi, Lai, & Ye, 2011). A challenge is, however, that aluminum and copper have high affinity to each other, especially at elevated temperatures. This causes formation of brittle intermetallic phases with high electric resistance (Liu, Wang, Sui, Wang, & Wenjiang, 2016). In addition, both metals are subjected to oxide formation on the surface. Copper is especially exposed to oxidation at elevated temperatures (Pinnel, Tompkins, & Heath, 1979), while a thermodynamically stable oxide layer will spontaneously form on the aluminum surface (Papis, Loeffler, & Uggowitzer, 2009). Oxides are known to be passive substrates, which will reduce wettability and will thus prevent the formation of metallic bonding between aluminum and copper (Papis, Hallstedt, Löffler, & Uggowitzer, 2008)."

Jan 1, 2018

By M. W. Bartley

DURING the field season of 1938, the Ontario Department of Mines assigned a combined geological and geophysical survey patty to the investigation of the location, genesis, structural relationships, and economic possibilities of the hematite deposits at Steeprock lake. The investigation was carried out by detailed mapping of the rock exposures and a magneto-metric survey of the drift-covered portions of the area. This was supplemented during the winter of 1938-39 by further geophysical work conducted on the ice. Dr. A. A. Brant, of the Department of Physics, University of Toronto, was in charge of the geophysical work for the Department of Mines in the summer and for the Sterola Exploration Company in the winter. The writer supervised the geological examination. Scope of the Paper The present paper is an attempt to acquaint the members of the Institute with the structure and mode of occurrence of the deposits, since many people are of the erroneous opinion that they are analogous to the Mesaba and Michigan deposits. It is hoped that, from this discussion, they may be able to draw some conclusions of their own regarding the nature of the deposits, and the importance and future possibilities of the region.

Jan 1, 1939

By F. Chiesa

Forty aluminium A356 castings were poured on a Low Pressure Permanent Mould industrial machine, 500x700mm in platen size. The 152mm wide casting comprised three steps, 25mm, 13mm, 6mm in thickness and a 2.5mm overflow which allowed to assess the thin wall capability of the process. The casting campaign, which produced 40 parts, allowed to test the influence of various production parameters including the time of application of the pressure in the crucible, artificial cooling of the mould and casting rate. The thermal history in the mould was recorded over the 40 cycles, which allowed to construct a reliable thermal model of the mould/casting assembly. The metallurgical quality of castings representative of the various conditions was assessed in the 25mm, 13mm and 6mm plates. This included measuring the level of microporosity, the dendrite fineness (DAS), along with the tensile properties in the T6 condition. The radiographic quality per ASTM E155 was also determined. Modelling filling and solidification allowed to verify the validity of the predictions based on available relationships relating microporosity, secondary dendrite arm spacing (DAS) and local tensile properties (Quality Index, Q) to the local thermal solidification parameters.

Jan 1, 2007

By Lang Tao, Jun Wang, Wei Xiao, Wenqing Qin, Pan Cao, Guanzhou Qiu, Key Lab of Biohydrometallurgy of Ministry of Education, Central South University

"The effect of metal cations on the rutile flotation using styryl phosphoric acid (SPA) as the collector was investigated by micro-flotation test, bench scale flotation test, zeta-potential measurements and adsorption measurements. The micro-flotation results indicated that Fe (?) and Al (?) ions in low concentrations had obvious activation on the rutile flotation, and Pb (?) ions in low concentrations had smaller activation of rutile, but Fe (?), Al (?), Pb (?), Ca (?) and Mg (?) have strong inhibition of rutile flotation in high concentrations. The bench scale flotation results indicated ethylene diamine tetraacetic acid (EDTA), boracic acid, and sodium hexametaphospate can decrease the metal ions concentrations, and increase the recovery of rutile flotation. Adsorption measurements and zeta-potential measurements revealed that Fe (?), Al (?) and Pb (?) ions were adsorbed on the rutile surface, and had interaction with SPA. But when these ions concentration were over the largest adsorption capacity, residual metal ions could occur chemical reaction with SPA.INTRODUCTIONRutile is one of the favored minerals for production of titanium dioxide white pigment, primarily through the chloride manufacturing process (Stanaway 1994; Hou et al., 2013) However, the majority of rutile ores belong to refractory ores, while flotation is one of the most efficient methods to separate fine rutile from gangue (Dolbear et al., 1937). With the flotation development, many effective collectors were successfully applied in the oxide ore. Many reviews have indicated that organic phosphonic acid collectors showed good selectivity on oxide ores such as ilmenite and rutile (Bulatovic & Wyslouzil 1999; Liu & Peng 1999).It is inevitable that many types of metal cations are present in ore pulp. These metal cations significantly influence the flotation of minerals. Liu et al. (2015) showed that Ca2+ and Mg2+ could improve the floatability of spodumene at pH 12.5 and 10.0, respectively. The authors proposed that Ca2+ and Mg2+ ions readily form hydroxy complexes (CaOH(l) and MgOH(l)) and precipitates as (Ca(OH)2 and Mg(OH)2) in strongly alkaline solutions. Fan and Rowson (2000) investigated the effect of Pb(NO3)2 addition as an activator on ilmenite flotation and showed that it could improve ilmenite floatability. The addition of Pb(NO3)2 resulted in an increase of ilmenite zeta potential in both weakly alkaline and acidic aqueous solutions. Mehdilo, Irannajad, and Rezai (2015) studied three kinds of ilmenite of different origins and discovered that both Mg and V had a negative correlation with ilmenite flotation, while the Mn content seemed to correlate positively with flotation efficiency. A number of studies have also showed that Fe3+ can improve the floatability of ilmenite (Fan et al., 2009; Nuri, Mehdilo, & Irannajad, 2014)."

Jan 1, 2016

"Ground control research in underground coal mines has been ongoing for over 50 years. One of the most problematic issues in underground coal mines is roof failures associated with weak shale. This paper will present a historical narrative on the research the National Institute for Occupational Safety and Health has conducted in relation to rock mechanics and shale. This paper begins by first discussing how shale is classified in relation to coal mining. Characterizing and planning for weak roof sequences is an important step in developing an engineering solution to prevent roof failures. Next, the failure mechanics associated with the weak characteristics of shale will be discussed. Understanding these failure mechanics also aids in applying the correct engineering solutions. The various solutions that have been implemented in the underground coal mining industry to control the different modes of failure will be summarized. Finally, a discussion on current and future research relating to rock mechanics and shale is presented. The overall goal of the paper is to share the collective ground control experience of controlling roof structures dominated by shale rock in underground coal mining.INTRODUCTIONThe National Institute for Occupational Safety and Health’s (NIOSH) Office of Mine Safety and Health Research (OMSHR), formerly the United States Bureau of Mines, has been conducting research on ground control safety for over 50 years. The overall objective of the research is to reduce underground mining injuries and fatalities by characterizing roof conditions, improving roof support performance and application, and optimizing pillar design and mine layout. Underground mining has one of the highest fatal injury rates of any industry in the United States—more than five times the national average compared to other industries (CDC, 2012). Roof fall injuries can be severe, resulting in lacerations, bone fractures, amputations, and death. Non-injury roof falls can also be problematic, resulting in lost production, delays, blockage of primary escape routes, disruption to ventilation, and hazardous rehabilitation conditions.Coal mining is increasingly subject to more adverse geological conditions. Weak roof can be found in all coal mining regions in the United States, but there are a few geographically isolated areas with higher roof fall rates contributed to by particularly poor roof conditions, as represented in Figure 1. This figure shows that when non-injury roof fall rates are normalized to production, the Illinois Basin and Central/Northern Appalachia regions have the highest rates. These isolated regions have inherently weak roof even before mining has occurred, and this roof is easily damaged during the mining process. The weak roof in these regions consists primarily of shale. Shale can be troublesome in underground coal mining because it can appear massive but easily splits along bedding planes and is often moisture-sensitive."

Jan 1, 2015

By Georgy A. Cherkashov, Andrey V. Efimov, Yury S. Borodaev, Nadezhda N. Mozgova, Sergey G. Krasnov, Tamara V. Stepanova, Alexander M. Ashadze

"Abstract - A horizontal mineralogical-geochemical ore zonation with a southeast to northwest trending succession of Cu and Fe (Zn) main zones has been discovered in the Logatchev hydrothermal field (14°45??N Mid-Atlantic Ridge). The major minerals are pyrite, chalcopyrite, bornite, isocubanite, digenite and chalcocite. Zn-sulfide, marcasite and covellite are less abundant. Rare minerals are native copper, zincian copper and cobalt pentlandite (first found in oceanic massive sulfides), Cu and Cu-Co-bearing Fe-disulfides. Two groups of the main sulfide assemblages with different copper contents are recognized: Group I comprises assemblages with primary sulfides (isocubanite, chalcopyrite, pyrite and Zn-sulfide; Cu up to 35 wt% in Cu-bearing minerals); Group II contains assemblages with secondary Cu-rich sulfides (bornite, digenite, chalcocite; Cu ~60 wt%) as well as rare minerals (cobalt pentlandite, native copper and zincian copper). The assemblages of Group I formed at a temperature of about 300°C; the sulfur fugacity (log fs2 atm) at 300°C is probably 9.9. Relations between minerals of this group are contradictory, attributed to non-equilibrium environments, and no unified sequence of crystallization of minerals has been determined. Minerals of Group II replace, rim or cross the assemblages of Group I. Group II minerals crystallized in a distinct sequence (cobalt pentlandite-bornite-digenite- chalcocite-native copper), with increasing copper content from the start to the end of the depositional sequence. This may correspond to pH from 7 to 8 near Eh = -0.2 at 250°C. Minerals of this group were generally formed under hypergene alteration processes. Compositions of ore minerals were studied by means of electron microprobe analysis (EMPA) (150 analyses). Narrow composition fields were revealed in all main sulfides, which comprised known experimental data. ZnS contains 6.0 to 28.0 mol.% FeS, which is close to data known for other hydrothermal massive sulfides from the Mid-Atlantic Ridge (MAR). A common admixture in ZnS is Cu (0.16 to 1.32 wt%). Rare grains of unusual anisotropic Fe-disulfides, (Fe0.95Cu0.05)S2 and Cu(Fe,Co)9S20, were found among the ore minerals."

Jan 1, 1999

By J. E. Dutrizac, Alba Sunyer

The factors affecting the precipitation of arsenic-free alunite (KAl3(SO4)2(OH)6) were investigated in a series of laboratory experiments. Although the amount of alunite precipitated increased with increasing retention time, temperature, solution pH and the concentrations of Al(SO4)1.5 or K2SO4, the composition of the products remained nearly constant. The preferred conditions identified for the precipitation of arsenic-free alunite were then used to assess the behaviour As(III) and As(V) during alunite precipitation at 98°C. Increasing additions of As(III), as NaAsO2 or As2O3, resulted in a slight increase in the amount of precipitate formed at pH 2.80. However, X-ray diffraction analysis showed all the precipitates to be alunite, and <0.2% As(III) was detected in the products. In contrast, increasing additions of As(V), as KH2AsO4 or As2O5, resulted in significant increases in the amount of precipitate formed at pH 2.80 or 3.00. Furthermore, the arsenate (AsO43-) contents of the precipitates increased up to 15%, and the sulphate contents decreased, as the As(V) concentration of the synthesis solution increased from 0 to 9 g/L. X-ray diffraction analysis of the products detected only alunite, but there was a progressive expansion of the alunite cell with increasing arsenate content. The implication is that arsenate substitutes for sulphate in the alunite structure. Preliminary observations on the environmental stability of the arsenate-bearing alunite using the TCLP protocol gave solubilities <0.4 mg/L from a precipitate containing 8.5% AsO4 and 7.8 mg/L from a product containing 19.5% AsO4. Thus, it appears that alunites containing less than -10% AsO4 would be an acceptable vehicle for the disposal of arsenic from hydrometallurgical processing solutions.

Jan 1, 2011

By D. J. Reddish

The paper describes a case study where numerical modelling has been applied to predict potential risks associated with inflows of water in active mine workings from an overlying sandstone aquifer. The objective of the modelling was to predict the development of strata fractures and strains as the longwall panels were extracted and investigate their relationship to an sandstone aquifer. The numerical modelling study also included the investigation of the effect of mining on a fault that existed close to the start position of one of the panels. The potential effects of mining on the fault were undertaken by parametric studies adjusting properties for the fault and the relative position of extractions, which allowed the mine planner to position the panel layout accordingly.

May 1, 2003

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By Joseph Carlston

With environmental regulations continuing to restrict the discharge of phosphorus from wastewater treatment facilities, traditional methods of phosphorus removal are proving inadequate. To achieve the phosphorus control necessary, a new coagulant used for phosphorus removal, cerium chloride, has been studied in several municipal and industrial wastewater treatment facilities that must meet a phosphorus discharge limit of 0.5 mg/L or lower. These studies demonstrated the high phosphorus removal capabilities of cerium chloride, with the results illustrating the ability for cerium chloride to reduce phosphorus to low concentrations in the effluent using a lower volume of product as compared to traditional coagulants, such as ferric chloride. This reduction is due to the unique ability of cerium chloride to remove phosphorus as cerium phosphate, whereas iron- and aluminum-based coagulants rely on adsorption and co-precipitation.

Jan 1, 2014

By C. W. Langenberg, D. E. Macdonald, R. S. Strobl

"The successful marketing of Alberta coals will increasingly depend, to a large degree, on an extensive coal quality information base. This information, at present, is generally based on a deliverable, cleaned coaland is confined to existing mine sites. Coal quality information is not as well understood for raw in situ coal outside of mine sites and even less is known about the geological factors that control it.If new uses and markets for Alberta coal are to be developed, such as gasification, coprocessing, and exploiting high rank coals for combustion, it will be imperative that the coal quality parameters important for these utilizations be known. These parameters need to be known for existing deliverable coals and, just as important, for as yet unexploited in situ coal. Factors such as the Cl, No, K, Co, P and trace element contents should be addressed to meet the requirements of these new utilizations.The geological characterization and explanation of what factors control these coal quality parameters is part of research being done at the Alberta Geological Survey. In-seam vertical profiling has been undertaken within the plains and foothills/mountains coals to determine exactly where coal quality variations occur and why. In the Ardley coal zone at the Highvale Mine it has been found, for example, that the ash content of the mined coal is made up of discrete partings and of microsized particles associated with inertinite macerals. The in-seam characterization of coal seams will lead to a better understanding of in situ coal quality variations, leading to new uses and markets for Alberta coal."

Jan 1, 1993

By R. Darlington, S. Ji

"High pressure die casting is a promising process to make thin-wall components with high dimensional accuracy and excellent surface quality. However, the non-uniformity is one of the important features in castings. The inhomogeneity in tensile properties and microstructural characteristics were studied for the castings with different thicknesses made by high pressure die-cast Al-Mg-Si alloys. For the local mechanical properties in the die-castings, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, UTS and elongation. The yield strength, UTS and elongation were significantly decreased towards the casting centre. The microstructural inhomogeneity is characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic a-Al phase estimated using the Jackson-Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.INTRODUCTION Inhomogeneity is an inherent characteristic in as-cast microstructures of a variety of alloys because of their non-uniform chemistry, microstructure, defects, topology and the resultant mechanical properties in the different ranges of localization (Campbell, 2003). Generally, three types of inhomogeneities characterise casting microstructures, which include (a) the casting defects of shrinkage and gas porosity, misruns, cold shuts, inclusions, hot tears and hot spots; (b) the non-uniform microstructure from the surface to the centre of castings; and (c) the non-uniform microstructure from the dendrites grown from primary solidification and the structure formed during the subsequent eutectic solidification in inter-dendritic regions. The chemical composition and the morphology between the primary dendrites and the inter-dendritic eutectics also differ in the as-cast microstructure. Obviously, the inhomogeneity is different in the castings obtained from different casting processes."

Jan 1, 2018

By J. Pepin

When using alternating current submerged arc welding (SAW) to produce pipes from microalloyed linepipe steels, it is critical to balance penetration depth and deposition rates, in order to minimize the number of weld passes while still maintaining good heat affected zone (HAZ) microstructures and properties. A series of bead-on-plate (BOP) submerged arc welds were performed on X70 steel, using different waveform variable settings (i.e., balance, offset and frequency). Weld bead cross-section profile deposition and penetration areas were measured, and both Vickers hardness and Charpy V-notch impact testing were performed. Both single electrode and tandem electrode welds were evaluated.

Jan 1, 2011

By Mosquera. J.

Tailings Storage Facilities (TSFs) are vast structures that respond to site-specific characteristics, rate of production, placement techniques, and the physical and mechanical properties of tailings. As a common denominator, TSFs are in some degree vulnerable to failure due to liquefaction, poor management, slope instability and/or unusual climatic events. In practice, stability of TSFS is determined by calculating a minimum Factor of Safety (FOS) using the Limit Equilibrium Method (LEM). However, it has been proven that relying exclusively on the limit equilibrium approach is not accurate because it is basically a static method that does not take into account the stress-strain distribution and displacement experienced by the constitutive materials of a TSF. In order to overcome these limitations of the LEM, the finite element method - Shear Reduction Technique (SRT) has been used as a more reliable tool for TSFs stability assessment. This paper presents a comparative stability analysis between an upstream tailings storage facility (UTSF), and a water retention tailings dam (WRTD) under static and pseudo-static states using simplified and rigorous LEMs and the SRT. Additionally, and taking into consideration the intrinsic uncertainty of tailings properties, sensitivity and probabilistic analyses in the form of Monte Carlo Simulation (MCS) and the Point Estimate Method (PEM) are applied to determine the Probability of Failure (Pf) and Reliability Index (ß) of each TSF. It is shown that the friction angle of UTSF?s foundation and the core?s cohesion of the WRTD are the main variables that govern stability. Further analysis shows that the WRTD has a higher reliability index and a lower probability of failure than the UTSF.

Aug 1, 2013

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"Abstract-The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek - Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern Black Hills or other areas of similar geologic settings."

Jan 1, 1995

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek – Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern BlackHills or other areas of similar geologic settings."

Jan 1, 1995

By N. R. Andrade-Gonzalez

In this paper, the effect of magnesium and strontium additions on the heat treatment behaviour of cast A319,2 alloy was investigated, Permanent mold samples were heat treated at 495 °C for 4 and 24 h, then quenched in hot water and aged at 180 °C and 220 °C for different temperatures, It is found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu alloys, mainly when Mg and Mg-Sr are added, The results of electron probe microanalysis (EPMA) observations reveal that the age-hardening behaviour is related to the precipitation sequence of alloys, For the Al-Si-Cu alloy, the first aging peak is the result of the high-density GP zones, while the subsequent peaks arise from metastable phases, Obvious intervals during the transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks, It is seen that addition of Mg (-0,40 wt %) leads to the precipitation of coarse Al5Mg8SioCu2 particles. When modifying the high Mg alloys, Cu-intermetallics segregate in areas away from the growing Al-Si eutectic regions, Modification with strontium retards the precipitation of the silicon out of the matrix.

Jan 1, 2005

By John E. Udd

In early 2000, CANMET-MMSL was engaged by the Ontario Ministry of Labour (OMOL) to conduct an international study of the practices, in several key mining jurisdictions, of determining the criteria that are used to decide when the wire ropes used in mine hoisting are to be retired from service. Subsequently, the writer visited key officials and institutions in Canada, the USA, the Republic of South Africa, the United Kingdom, Germany and Poland. Material from the Australian province of New South Wales and Hungary was also included. The report that resulted included, among other sections; (1) the history of wire rope and trends in manufacturing technology; (2) a review of mine hoisting practices; (3) the requirements as regards safety factors; (4) a review of the players and the inspection practices; (5) the criteria for rope replacement; (6) a look into the future to outline the developments that could take place in both hoisting and rope inspection practices in Canada; (7) recommendations. Subsequently, the report was issued as a book by OMOL, and as a CD-ROM by the Mining and Mineral Sciences Laboratories, Natural Resources Canada. In this paper the author presents the key findings and the recommendations made in the study.

May 1, 2003

By G. Knight

"Results of a program of dust research carried out at the Mines Branch Laboratory, Elliot Lake, indicate that dust-concentration estimates vary greatly, depending on the sampling instrument, the assessment technique and the properties of the dust cloud. The wide range of the ratio between the estimates by any pair of instruments shows that the correlation between the health hazard and dust-concentration estimates by most existing sampling instruments must be questionable. Important studies are being carried out to permit the definition of mine environments in more precise technical terms. The influence of size selection, the physical property measured, composition and sampling period on the assessment of the health hazard are discussed."

Jan 1, 1969