Search Documents

By M. E. Holuszko

Although there is no widely accepted rigorous definition of handleability, the handling coal characteristics often referred to as handleability define whether a coal has the ability to flow unhindered through the processing and transportation systems. The handleability may be severely affected if fine coal particles tend to aggregate. In the pelletization process, the rolling action of the drum is applied to bring the individual particles into proximity with each other so that they can aggregate and form pellets. Because of apparent similarities between these two processes, the pelletization tests are carried out in parallel to the handleability tests in this project, and the pelletization results are used to explain coal handleability properties.

Jan 1, 2004

By Håkan Schunnesson, Kirsten Holme

"When mining high grade, narrow ore bodies, the mining method often implies a very detailed knowledge of the ore contacts to avoid unacceptable ore loss and waste rock dilution. During the past decade, the use of microprocessor based drill monitoring equipment has become an accepted technique, even for percussive drilling. On the basis of the recorded drill performance, such as penetration rate, torque pressure, thrust etc., a fast evaluation of the lithological sequence of the ore zone can be made. In order to evaluate the potential of percussive drill monitoring to pro-vide detailed information of the geometry of the ore body, the technique was tested in the Viscaria copper mine in Sweden during 1996.To provide understandable information to the mine geologist, great emphasis was placed on the separation between the drilling response generated by variations in rock conditions from variations caused by the operator and the drill system. Due to the complicated geology in Viscaria, the drilling response presented to the geologists was separated in two independent signals, one representing the hardness of the rock and one representing the in homogeneity(fracturing) of the rock. With those signals a good separation between different rock types in the ore horizon was achieved.The experience from the Viscaria copper mine is that drill monitoring not only can be used to locate contacts between rock types, but also to characterize rock conditions and, often, also to specify the exact rock type present. Because it is possible to get the drill monitoring information very quickly it is a valuable complement to diamond drilling for increasing the specific knowledge of the geology and the ore body."

Jan 1, 1997

By Mory M. Ghomshei

"The cost of deep underground mine cooling depends on a number of geological, environmental and economic factors such as the temperature gradient in the mine, the outside air temperature, and the local price of energy. While geological factors, being static, can be controlled to some extent during the mine design, the environmental and economic factors dynamically change and therefore can only be controlled through a flexible mine ventilation system.With an average temperature gradient of 20–25°C/km, the virgin rock temperature at 2,000 m can reach 45–60°C. Conventional cooling at such depths could lead to exorbitantly high costs. In-mine geothermal heat pumps can considerably reduce the cost of cooling through energy communication with the centralized absorption chillers, which service the mine from the surface.It is shown that in-mine heat pump systems can be a viable option for reducing operating expenses and providing some degree of flexibility to cope with fluctuating energy costs. The price of Natural gas and electrify are the most important variables for optimizing the level of interaction between the surface and inmine cooling systems. Deep mine waters can be used to carry a portion of the mine heat to the surface, where the heat from mine can be used as a supplementary energy source for absorption chillers. As an extra benefit, the heat output of the chillers can be used for district heating and or greenhouse growing.The case of cooling deep levels of deep mines in Sudbury Canada (e.g. Creighton Mine) has been discussed. It is shown that an initial 1MW in-mine geothermal heat pump system can save significantly on the cost of cooling. Such a demonstration project will allow R&D on viability of larger similar systems to be incrementally added in the future.INTRODUCTIONThe amount of heat generated in deep and ultra-deep mines depend primarily on the regional temperature gradient and the thermal conductivity of mine rocks. The conductive heat flow is quantifiable and can be minimized or optimized in the process of mine design. Another important heat source can be related to underground equipment such as diesel machinery which often have low efficiencies (approximately 25–35%). This heat source can be controlled and reduced though improving efficiencies or using electrical equipment, which offer a much better efficiency (approximately 80–90%). Mine waters can also be a significant heat source (convectively bringing large amounts of heat into the mine workings)."

Jan 1, 2019

By George R. White

"The Phalen Colliery, the Cape Breton Development Corporation's flagship, is now producing thermal and metallurgical grade coal in Eastern Canada's Sydney Coal Field. The colliery is a drift mine operating under the waters of the Atlantic Ocean. Improved mechanization, including a 2200 tonne per hour cable conveyor, and the introduction of modern retreat longwall mining methods as part of the Phalen concept are now paying off in better productivity and low operating costs. Geological conditions within the coal field are consistent with plans for ever greater outputs in the 1990s. Although much of the current production improvement is related to uprated machine capacity and simplified mines planning there is potential for even further development in the areas of maintenance, process control and engineering. Human resource development will also be a key factor. These programs are now well under way and Phalen Colliery is poised for top results in the 1990s. Comparison of the CBDC's top producer with similar operations elsewhere in the world, quantifies that potential.IntroductionAn exciting new mining project which has recently started production on Canada's East Coast has been conceived and designed to be one of the most modern and productive coal mining operations in North America.As with all mining operations, the business is basically that of material transportation. Daily, the product is transported many kilometres from the underground face to the surface and then to washing facilities. Men, materials and equipment are transported to and from the surface and the operating faces and services, such as electrical power, ventilating air, fresh water, discharge water, communications and compressed air are supplied throughout the operation to cover operating requirements. On all accounts the operation has been designed to take advantage of the latest proven technology."

Jan 1, 1990

By S. C. Ells

Within the Dominion of Canada occurrences of petro-liferous shales have been known for many years. Nevertheless, with the exception of a comparatively brief period, Canada has had to depend largely on foreign sources for its supplies of crude petroleum and petroleum products. Attempts were made to retort local shales in 1859, near Collingwood, Ontario, and again in 1862, near Baltimore, New Brunswick. In each instance these attempts were abandoned owing to the rapidly increasing production of well petroleum from the newly discovered pools of western Ontario and Pennsylvania. Now, after a lapse of nearly sixty years, attention is again directed to the commercial value of Canadian shales as a possible source of crude petroleum. Province of Nova Scotia: The principal deposits of oil-shales occur in Pictou and Antigonish counties and have been known for more than 60 years. During the three years following its discovery, several thousand tons of a particularly rich sub-variety, known as stellarite (stellar coal or oil coal) was mined near Stellarton in Pictou county. It is stated that stellarite yielded upwards of 10,000 cubic feet of 36 candle gas, and that selected samples gave a yield equivalent to 170 Imperial gallons (204 U.S. gallons) of crude petroleum per ton. The average petroleum content of a cargo shipped to Boston was 48 Imperial gallons (57.6 U. S. gallons) and the associated shale or 'bat', gave a yield of 39 Imperial gallons (46.8 U.S. gallons). Part of the above output was shipped to retorting works in Boston and in Portland, and part was mixed with bituminous coals for the enrichment of illuminating gas. Following the discovery of well petroleum in Ontario and in the United States, the mining of stellarite ceased.

Jan 1, 1925

By S. H. Schulz

100 YEARS AGO, on the first of August, 1877, the mining engineer Friedrich Koepe was granted the patent rights for a hoist driving ropes on the principle of friction. It was named after him: the Koepe hoist. On the occasion of this centenary, the main features of the Kcepe principle are described.

Jan 1, 1977

By M. Bender, H. D. Goodfellow

"Belt conveyors, because of their low capital and operating costs and inherent flexibility in handling a wide variety of products, have numerous applications in the mining industry. With the increased emphasis on improving the workplace environment, dust emissions from belt conveyors at transfer and other points have become a significant problem for many applications.The paper reviews belt conveyor dust control technology and compares dust emissions from belt conveyor systems with other possible materials handling systems. Technical information on existing belt conveyor installations which have been designed to minimize or eliminate dust emissions is summarized. The important features of good design as well as the necessary input from operating and maintenance personnel are highlighted. The status of research and development work on dust control on belt conveyor systems on a world-wide basis is discussed. A proposed methodology for field measurements of emission factors from belt conveyor systems is presented. Data collected from such a test program can be used to establish a design basis for new dust-free belt conveyors.IntroductionBelt conveyors have proven themselves over the year s in the mining industry as a reliable and low-co st method of moving bulk material at high tonnage rates. Because of the above, as well as their inherent flexibility in handling a wide variety of products, belt conveyors are often called the ""workhorses"" of bulk material handling systems. For many processing plants, belt conveyors serve as the ""vital link"" in providing feed to the plant and the removal of the finished product. As would be expected, there has been considerable engineering effort in designing rugged and reliable belt conveyor systems.It is also well known that belt conveyor systems are a primary source of respirable dust emissions. The major sources are from the tail pulley where material is received and the head pulley where material is discharged, from the return idlers, due to the fine material attached to the return belt, and from the take-up pulley. It is usually considered that for dust particles less than 10 microns, these particles will remain airborne and thus can have a profound effect on the workplace environment."

Jan 1, 1982

By J. C. Folinsbee, D. R. Derry

"The Property of Opemiska Copper Mines (Quebec) Ltd. is in Levy Township, Chibougamau district, west of Chibougamau and south of Opemiska Lake. The original find was made in 1929 by the late Leo Springer and associates of Prospectors Airways Ltd., following observation from the air of an area of dark rocks in newly burned-over country. Work on the ground discovered three veins of high-grade chalcopyrite in gabbro (No. l, No. 2, and ""North"") and, after several seasons of trenching and diamond drilling, financed by Ventures Ltd., a shaft was sunk in 1936. This work indicated about 280,000 tons of six per cent copper ore to a depth of 500 feet. During this period, the senior author carried out a reconnaissance geological survey over the whole property and surrounding claims, which showed that the veins were in the gabbro portion of a large composite basic sill that had been folded with the enclosing lavas. Owing to the low price of copper and lack of transport work was suspended and the property remained dormant until 1951.In that year the company was re-financed, the property prepared for production, and further exploratory drilling undertaken. The drilling, based on structural indications, located a new vein of which the only previous evidence had been some irregular stringers. This vein, No. 3, was traced by drilling for a length of 2,000 feet and the indicated reserves were thereby increased to about one million tons. An additional vein, No. 4, was intersected in several holes.With this encouragement, plans for production were confirmed, and operations commenced' at the beginning of 1954 on a scale of about 400 tons a day, concentrates being shipped by truck to St. Felicien and thence by rail to Noranda. In the first year of operation concentrates were re-covered carrying 14,047,210 pounds of copper, 76,714 ounces of silver, and 6,259 ounces of gold. The operation is under the direction of J. P. Millenbach, General Manager, with J. M. Thompson as Assistant General Manager and F. G. Cooke as General Superintendent on the property."

Jan 1, 1949

By J. K. Weglo, M. U. Savich

"The measurement and evaluation of the noise emanating from an ST4A scooptram in an underground stope under a simulated work cycle, and under three conditions of after-treatment systems is covered.These include scooptram without muffler or filler (bare engine), an in-line small filter, compared to a larger-filter, and the larger filter with an in-line muffler in series with fume diluter, which were tested under three engine operating conditions-IDLE, wide open throttle (W. 0. T.), and working condition. This is load, short haul and dump operation.The results showed an attenuation of the scooptram at work of 8 to 15 dBA, 16 cm from the exhaust pipe of the machine, to 4.8 dBA at the operator's ear. Recommendations are made to increase the attenuation at the operator 's ear by additional improvement in design of the fume diluter.IntroductionIn current mining operations, the diesel engine provides a safe, efficient and highly mobile source of power. In the major underground mine s in Canada the most common types of diesel equipment are load-haul-dump (LHD) machines and ore trucks. In general, there is a tendency to use high horsepower, diesel LHD machines in mines to achieve maximum productivity. The increased use of diesel-powered equipment in underground mines has shown no cause pressure levels were measured at the exhaust and outlet pipe. Also, while measuring the octave band and A-weighted sound pressure levels, the operator's position was also measured."

Jan 1, 1986

By H. Hitchen

THE PURPOSE of this paper is to indicate the working capacity of different types of ropes for various engineering and mining duties. ROPE CONSTRUCTIONS There are approximately one hundred different designs of ropes in use today but, normally, only about ten are necessary for mining and engineering duties. The rest are designed for unusual equipments, or are different ways of combining wires of special shapes. Basically, the various designs of mining ropes consist of round, triangular, and oval strands, constructed with one or several layers of wire over a single wire, or a compound construction of sever.al wires. To suit different installations ropes are made with 3, 4, 5, or more of these types of strands over a central core, the ?co re itself being manufactured from either a fibrous material or a combination of steel wires. Nevertheless, in mining, the demand for 'locked coil rope', wl1ich may be considered as a single strand, is steadily increasing, especially for use on vertical shaft winding engines. So far as the locked coil rope is concerned, many constructions have been developed to suit different requirements, such as - in addition to winding ropes - aerial carrying Topes, shaft guide ropes and haulage ropes.

Jan 1, 1957

By Denis Beaudoin

Program Basics: Goals, Course Content & Training Process Sudbury: History of the Program & Lessons Learned Diavik: History of the Program & Lessons Learned Most Recent Program: Totten Mine in partnership with Sagamok Anishnabek Summary -Lessons Learned Conclusion

Oct 1, 2010

This document presents estimates of future "total cash cost per ounce" and "minesite cost per tonne" that are not recognized measures under United States generally accepted accounting principles ("US GAAP"). This data may not be comparable to data presented by other gold producers. These future estimates are based upon the total cash costs per ounce and minesite costs per tonne that the Company expects to incur to mine gold at the applicable projects and do not include production costs attributableto accretion expense and other asset retirement costs, which will vary over time as each project is developed and mined. It is therefore not practicable to reconcile these forward-looking non-GAAP financial measures to the most comparable GAAP measure. A reconciliation of the Company's total cash cost per ounce and minesite cost per tonne to the most comparable financial measures calculated and presented in accordance with US GAAP for the Company's historical results of operations is set forth in the notesto the financial statements included in the Company's Annual Information Form and Annual Report on Form 20-F, for the year ended December 31, 2009, as well as the Company's other filings with the Canadian Securities Administrators and the SEC.

May 1, 2011

By Eirik Sundvor, Hany Doss, Peter Vogt, Kathleen Crane

"Abstract - In 1989-1990, the SeaMARC II side-looking sonar (11 to 12 kHz) and swath bathymetric system imaged more than 80 000 km2 of the seafloor in the Norwegian-Greenland Sea and southern Arctic Ocean. One of our main goals was to investigate the highly oblique (115°) junction between the Mohns and Knipovich ridges, and to determine, using new morphotectonic data, whether or not this junction is stable or in a state of readjustment. These findings are presented in this paper.Along the northern Mohns Ridge, we observed a highly segmented rift valley undisturbed by transform faults. In contrast to the elevated Reykjanes Ridge, the Mohns Ridge is dominated by deep en echelon fault-bounded troughs, which are bordered by high rift valley volcanoes. These segment boundaries are interpreted to be sites of recent to present volcanic activity, based on their high acoustic reflectivity. The northwestern flank of the Mohns Ridge is marked by shallow quasi-linear ridges parallel to the present orientation of the Mohns Ridge. The orientation and geographic position of these ridges suggest that they were formed at the Mohns Ridge. Only in the northernmost cases are some of these off-axial ridges non-linear. The degree of the non-linearities increases slightly with proximity to the Mohns-Knipovich bend. In addition, because no transform fault was detected between the Mohns and Knipovich ridges, we conclude that the Knipovich Ridge must be obliquely spreading to the NW-SE."

Jan 1, 1999

By Jason Mewis

Do you have it figured out? ? If so, I want to network with you! ? There?s a lot to learn as an industry The more we share the better we?ll all become at dealing with this subject If you don?t have it figured out ? You?re among the majority in the in0dustry ? Project Risk is a broad and complex issue that is dealt with through many processes ? And it?s not intuitive either ? And you don?t want to confuse one process with Another

Nov 1, 2011

By B. B. Adhikari, S. Alam, Ohto Kawakita, Abe Pangeni

Effective recovery of gold was investigated by using adsorption gels prepared from pure cellulose, cotton and paper by treating with concentrated sulfuric acid. Only gold was adsorbed with extraordinary high loading capacity from varying concentrations of hydrochloric acid separated from other precious metals and base metals. The formation of fine powders of metallic gold was visually observed, which is attributable to the selective reduction of gold (III) ion to metallic gold clue to its high oxidation-reduction potential. Recovery of gold from the leach liquor of hydrochloric acid of circuit boards from spent mobile phones was attempted using pure cellulose gel.

Jan 1, 2011

By Howard J. Handewith

"Tunnel boring machines have been tried in underground mining applications as early as 1957. Although tunneling machines hardly threaten to supplant traditional drill-blast-muck operations for drifting, the latest modern machines offer substantial improvements in progress rates over traditional methods under certain conditions.An evaluation guide is offered which identifies conditions that favour machine boring. Different types of costs related to the use of a tunnel machine are discussed. The advantages of the tunnel machine over the traditional method are reviewed. IntroductionThe first tunnel boring machine ever used in a mine was in Quebec in the year 1957. Although less than successful at the time, this experiment served to illustrate the mining industry' s willingness to try new ideas. Since 1957, the manufacture of tunnel boring machines has developed into a full-size industry. Most contractors in Europe and North America will now consider the use of a tunnel boring machine first on any long tunnel that can have a circular section.The modern tunneling machine offers a great potential to the mining industry. Just as the blasthole and raise drill machines have revolutionized mining in the last decade, it is expected that tunnel boring machines will make an equal impact in the future.This is not to suggest that tunnel boring machines will replace explosives in the foreseeable future, but they can supplement drill-and-blast operations. In areas where long drifts, inclines, declines or cross-cuts are needed in a hurry, the tunnel boring machines offer the fastest way to a production return on investment. Figure 1 shows the range of production that two types of tunnel machines have produced as compared with conventional excavation methods in various ground conditions.Rotary hard-rock tunnel boring machines (Fig. 2) commonly produce progress rates in excess of 20 metres per day in uniform ground from 300 to over 2,000 kgl cm2 in unconfined compression strength . These averages are for the completed tunnels. One 7. I6-metre-diameter tunnel boring machine just completed a 1O.7-km tunnel in hard rock of 700 to 2,800 kg/cm>, The last eight months of production averaged 30 metres per day."

Jan 1, 1980

By H. Miki, S. Wheatley

The addition of precipitated silica greatly enhances chalcopyrite leaching in the presence of sodium chloride at moderate temperatures (65-90°C) in acid media with ferric ions as the oxidant. The beneficial effect increases with the increase in chloride concentration and temperature. The addition of sodium silicate and silica sand has no significant influence. The analysis of solubility data in acid/salt solutions indicates that the solubility of silica as Si(OH)4 as the dissolved species is controlled by the activity of water, as expected from the hydration theory. Kinetic analysis shows the trends that copper dissolution from chalcopyrite in the presence of precipitated silica with sodium chloride follows a shrinking sphere model indicating a chemically controlled surface reaction. The effect of temperature on copper dissolution in the presence of both precipitated silica and sodium chloride was also larger compared to the results in sodium chloride alone. The SEM analysis shows that chloride and silica facilitates the precipitation of sulfur on the surface of the silica particles rather than the chalcopyrite particles which avoids the blockage of the mineral surface and thus improves the leaching kinetics.

Jan 1, 2014

By R W. Drybrough

The program to increase production at Sherritt Gordon's Lynn Lake property, which began in 1956, included increasing the rope speed and the horsepower of the ore hoist at the "A" shaft. Because of the limited power sup-ply from the two 7,000-hp. hydroelectric plants, and the ? 3,600 hp. predicted for the combined hoisting requirements of the three production shafts, it was considered desirable to lessen the impact of this type of load on the relatively small power system by equipping all future hoisting arrangements with Ward Leonard direct-current drives. The manually operated 8-by 4-ft. hoist at the "A" shaft had a rope speed of 1000 f.p.m., and was driven by a 385-hp., 380-r.p.m. wound rotor motor with liquid rheostat control. This A.C. drive was replaced by a semi-automatic Ward Leonard direct-current drive with a 515-hp., 566-r.p.m., shunt wound motor, providing a rope speed of 1,500 f.p.m. During several months preceding the con-version, all possible preparations were carried out to keep the changeover period to a minimum, and this resulted in a total shutdown time of twelve days. The capability of the "A" Shaft hoist was increased from 109 tons per hour to 134 tons per hour, and both mechanical and electrical maintenance were reduced considerably. The total cost of the conversion amounted to $130,000. The hoistmen who had been required for the manual A.C. drive were transferred to the new Farley shaft, and the reduction in operating labour costs of the "A" Shaft hoist

Jan 1, 1965

By J. R. CAMERON

Gypsum is mined in all Atlantic Provinces except Prince Edward Island. It is generally thought to have been derived from the hydration of anhydrite in areas of minimal drainage. Late Devonian downwarping and crustal oscillation east of the Appalachian fold belt allowed the Windsor Sea to advance and retreat in a depositional trough and deposit about 1,000 m of sediments in Mississippian time, much of which were evaporites. The best areas for further gypsum development are lowland basins such as the Cape Breton Lowlands, the Hillsborough area of New Brunswick and the St. George's Lowlands in Newfoundland, all of which are already sites of gypsum quarries. Nova Scotia's gypsum is mined from the Lower Windsor Group, which is divided into subzones 'A' and 'B'; 'B' provides most of the province's gypsum production. The Atlantic Provinces gypsum industry has markets from the St. Lawrence waterway to the mouth of the Mississippi River.

Jan 1, 1984

By R. K. Jonas

Many leading copper and other mineral processors have rapidly adopted advanced controls in last 5-10 years. Almost 600 multivariable predictive controls have been installed in mineral processing, and almost 50% of those are in copper concentrator plants. In most cases, mineral processors rely on 3rd party support to implement these advanced technologies. One challenge facing advanced control user is the selection providers and services for these technologies. The trend has been towards the use of multivariable predictive control and use of technology provider’s services. This paper will discuss status of advanced control, and the merging trends in the mining industry. A review will be presented of how advanced control is being applied in the mining industry over the last decade, and how user challenges are being overcome. Next the emerging uses of multivariable predictive control (such as multi/inter-unit optimization), focusing on the latest trends in concentrator plants. Finally, a review will be made of emerging technology advances in the that can be advantageous to mineral processors. INTRODUCTION Review of advanced control in mineral processing Advanced controls are serving an increasing role to improve processing plant operations and profitability. As advanced control is being installed into more mining processing plants such as copper concentrators, many of these plants are concerned about the selection technologies and vendors to support the installation and maintenance of these controls. In a study by Jonas and Craw (2011), they found that most new users have not had prior experience with advanced controls. It is the author’s experience of almost 30 years in advanced controls that most mineral processers considering advanced controls can benefit from better understanding of the technologies and their support requirements.

Jan 1, 2019