Search Documents

By A J. Weston

Block or panel caving technology is far removed from that of the top slicing and block caving of the late nineteenth or early twentieth centuries. The rapid mechanisation and expansion of these methods in the late twentieth century was as much a result of the change of the technology of the unit operations of development, ground support, drilling and blasting and transport as it was of the advances in geotechnical understanding and practice. The small footprint gravity and scraper block caving mines with boundary weakening, rail transport and shaft hoisting of the early to mid-twentieth century have been replaced by massive high lift panel caves using preconditioning of the ore, large load-haul-dump units, adjacent crushers and conveyors to surface. The technology changes in the unit operations are described and the drivers for these changes examined.CITATION:Weston, A J, 2016. The evolution of block caving technology, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 265–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R Crosbie, K C. Runge, E Tabosa, J K. McMaster

Flotation feed density is an operating parameter which is currently not well understood. Most models of flotation only incorporate its effect on particle residence time, but it is likely to have additional effects within both the pulp and froth phases of the machine. Test work was performed in MetsoÆs 3 m3 RCS test rig to investigate the effect of flotation feed density on metallurgical performance. The rig was operated at Rio TintoÆs Northparkes operation using flotation feed and scavenger tail. For each feed, tests were performed at different feed densities, and measurements were performed to estimate the pulp and froth recovery as well as other key flotation parameters (eg bubble size, turbulence and froth stability). Results of this test work have shown that the pulp density does affect key parameters of the flotation process in both the pulp and froth phases. Pulp phase kinetic rates decrease at high density and this is attributed to a reduction in the turbulence within the cell. Froth phase recovery, however, improves presumably because of a stabilising effect due to a greater loading of solids on bubble surfaces.There is a need for more research to be done to better understand these interactions so that metallurgists can determine the optimum flotation feed density to use at a particular operation, or within a section of a flotation circuit.CITATION:Runge, K C, Tabosa, E, Crosbie, R and McMaster, J K, 2012. Effect of flotation feed density on the operation of a flotation cell, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 171-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By H Esterhuizen

The Ernest Henry Mine (EHM) in Queensland, Australia is a Sub-level Caving operation that started production below the previously mined open pit at a depth of 535m. Current Production mining has progressed to a depth of 730m, with planned production mining to extend down to at least 1000m below surface. The inclined nature and geometry of the orebody combined with geological structures provides for challenging mining conditions. Over several years, Ernest Henry Mine has introduced measures to improve outcomes based on observations, monitoring and data analysis. As mining progresses deeper, EHM will continue to proactively take steps to ensure future outcomes are anticipated and mining can continue safely and uninterrupted. The focus of this paper is on the changes in seismic- and stress-driven behaviour of the rockmass experienced at EHM, the ground control measures implemented, and the anticipated future conditions and controls required. CITATION:Esterhuizen, H, 2018. The evolution of seismicity and ground control measures at Ernest Henry Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 20–41 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Ross

The foundation of effective leadership is communication. You can have all the leadership theories, models and training you want, but in the end it is all about leaders talking to, listening to and understanding the point of view of those below and above them.The foundation of effective safety is peoples’ behaviours. Every incident, every near miss and every safe act comes down to what one person does and how that affects themselves and others. We tend to focus these behavioural considerations on the people at the ‘coal face’, those most in harm’s way. But it is the individual behaviours of everyone in the organisation, particularly those at the top, which are just as (if not more) important. The foundation of effective safety leadership in the mining industry is that it starts at the top, with the individual behaviours of leaders. The behaviours of each and every leader will be reflected in their teams. And where their teams are made up of leaders, these leaders will pass these behaviours on to their teams and so on. It’s the sum total of what people see their leaders do and what they do as a result, that creates the ‘culture’ of the business – and it’s this culture that makes or breaks how safely people work.

Mar 21, 2011

By Mahyera A, Sakashita B, Ahmed U, Abou-Sayed AS

Gas in U.S. coals is primarily composed of 90 to 99 percent methane and up to 10 per- cent carbon dioxide. In composition and heat- ing value, this coal-bed gas is similar to natural gas and can be introduced directly into commercial pipelines after standard condition- ing. The high permeability cleat system in the virgin coal can be exploited in order to drain the coal gas well in advance of mining. Two premining drainage methods have been extensive- ly evaluated in the U.S.; they are 1) horizon- tal boreholes collared from within the mine, and 2) vertical drilling from the surface with fracturing. Limited-size fracture treatments are advocated in order to prevent potential roof damage and the need for added support. An engineering approach to predicting gas flow for different drainage techniques near mining locations is presented. Results can be used in design, i.e. pipeline, compressor. Coal gas drainage from a horizontal borehole and a treated (contained fracture) vertical well for a 6 foot seam have been evaluated. Based on these results, it was concluded that selection of gas drainage techniques will depend primar

Jan 1, 1982

By M L. Cramer, N P. Wines

"On 9 February 2014, bushfire embers landing on exposed coal in a disused pit at the Hazelwood mine in Victoria’s Latrobe Valley ignited a coal fire that burned for 45 days. The fire was the largest and longest burning mine fire to occur in the Latrobe Valley (Hazelwood Mine Fire Board of Inquiry, 2016). Two Victorian Government Boards of Inquiry have been held into the Hazelwood mine fire. The most recent, in 2015, included consideration of the regulation and implementation of rehabilitation practice at Hazelwood and the other two brown coalmines of the Latrobe Valley (Loy Yang and Yallourn; Government Gazette, 2015).The 2015 Hazelwood Mine Fire Board of Inquiry commissioned Accent Environmental Pty Ltd (Accent) to undertake a review of the financial mechanisms for mine rehabilitation and closure adopted in Australia and overseas (Accent, 2015). Specifically, Accent was engaged to identify ‘any practical, sustainable, efficient and effective alternative mechanisms to ensure rehabilitation of the mines as required by the [Victorian] Mineral Resources (Sustainable Development) Act 1990’ in accordance with Terms of Reference 10 (c) (Government Gazette, 2015).The review by Accent included consideration of a range of financial instruments such as bank guarantees, trust funds and insurance. It considered a number of financial assurance systems in operation in Australia, New Zealand, the European Union, Canada and the United States. These systems included: full and discount financial assurance systems predefined liability proportion systems pooled fund systems the use of post-closure financial mechanisms such as trust funds (Accent, 2015).What lessons can be learnt from other jurisdictions? Are there financial mechanisms already in place that could allow the Victorian Government and the mine operators to manage the risk of rehabilitation default3, lower rehabilitation liability, attain site rehabilitation objectives and allow eventual site relinquishment?CITATION:Cramer, M L and Wines, N P, 2016. Global lessons for a local problem – rehabilitation bonds and Victoria’s Latrobe Valley coalmines, in Proceedings Life-of-Mine 2016 Conference , pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By P M. Hetherington, F A. Pym, M P. Murphy, K E. Crook

Consultants in the mining industry have the opportunity to visit interesting deposits all over the world. Each deposit has its own set of challenges to face when it comes to defining and understanding the deposit geology and the economics to make it viable for extraction. Some of the challenges can include appropriate data capture, sampling techniques, structural characteristics, geochemistry, geophysics, lithology definition, and economic boundaries. It is essential that the practices used at each deposit (eg drilling, sampling, geological modelling, resource estimation etc) are documented and the results obtained are robust and defensible. The Competent Person is not always aware of instances where their resource estimation practices have not been substantiated. ‘You don’t know what you don’t know’ is a phrase frequently used during a mineral resource audit. Technical work to substantiate drilling, sampling, density, assaying, geological modelling and estimation processes is not always completed. Audited Competent Persons often comment: • ‘I was unaware that this was required.’ • ‘I have not had training in this area and do not know how to complete the checks required.’ • ‘This is how we’ve always done it.’ Examples of audits where it was found that geological practices were not substantiated are examined here. A discussion is included on why substantiation of these practices is important, and potential reasons as to why there are instances of unsubstantiated processes and practices are discussed.

Mar 22, 2022

By J T. Carswell, N A. Schofield

Fluctuations in periodic reconciliations between the mine and the mill are an expected and common experience in mining and processing operations. These fluctuations are caused in part by errors in the estimates of tonnage and grade of the mined material as well as errors in the millÆs assessment of the material processed. Keeping these errors small and unbiased is an important aspect of an efficient operation whose primary goal is to derive maximum benefit from the exploitation of the mineral resource.These fluctuations in periodic reconciliations can also mask subtle but economically important problems which may take years to identify and resolve. Such problems can result from a poorly-conceived model of the mineralisation which affects both the spatial distribution of the ore as well as the tonnage - grade distribution over the range of cut-off grades. Poorly conceived models of the mineral resources and ore distribution can arise as a result of insufficient and inadequate?drilling and sampling of the mineralisation, inappropriate?application of geological?constraints in the estimation process and the use of inappropriate methods to estimate the block grade distribution. This paper presents three case studies from gold and copper mining operations, two of which experienced significant problems with their mine to mill reconciliations over extended periods of time. For the gold mine in case study 1, sampling problems were ultimately considered to be the main cause of the poor reconciliations between grade control predictions and the mill which persisted over a period of 18 months. In addition, incorrect application of resource modelling methods contributed significantly to a mismatching of the mill capacity with the mine at the beginning of operations. For the underground copper mine in case study 2, a change in the approach taken to resource modelling brought marked improvements in ore definition and more accurate predictions of ore grade and better production forecasts.The third case study describes the background to the expansion of production to exploit a large tonnage of lower-grade stockwork mineralisation in an open pit gold mine. Several years of favourable Mine to Mill reconciliation data from the mining and processing of higher grade and lower grade stockwork styles of gold mineralisation provided the confidence in the approach to grade control to support the expansion plans during a period of low gold prices.The paper is intended to complement the discussion of mineral resource estimation methods and risks in Section 6.1.3 of the Mine ManagersÆ Handbook to be published by the Australasian Institute of Mining and Metallurgy (Schofield, 2012).CITATION:Schofield, N A, Moore, J and Carswell, J T, 2012. Mine to mill reconciliation - Three case studies, in Proceedings International Mine Management 2012, pp 161-172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By R Sinclair, D Landwehr, I Hunter

"The Syama Gold Mine, located in southern Mali, was established in 1990 by Broken Hill Propriety Limited (BHP). The operation began treating oxide, and in 1994 it transitioned to processing hard and refractory ore based on ‘whole-of-ore’ roasting. In 1996, BHP was succeeded by Randgold Resources and the operation ran until 2001, when it was placed into care and maintenance.The Syama ore is classified as a double refractory ore with pyrite occluding the fine grained gold present in the ore and high levels of organic carbon presenting a challenge in terms of preg-robbing behaviour. The ore is extremely competent and this combination of metallurgical features was the main source of metallurgical problems encountered by the previous owners.Resolute Mining Limited (RML) acquired the Syama project in 2004. Following a feasibility study and the development of a revised processing flow sheet the plant was recommissioned in 2008 using a combination of old and new equipment. The revised flow sheet enabled primary sulfide ore to be treated by flotation and roasting of the concentrate to produce a calcine suitable for conventional carbon-in-leach (CIL) processing.Commissioning and ramp up of the plant was a troubled process, with monthly gold production being as low as 3000 oz in 2010. Poor availability of equipment and lower-than-forecast recoveries were the primary contributors.During the last five years, RML has utilised a systematic approach to improve production, focusing on mechanical reliability, metallurgical recovery and process bottlenecks. Modifications to the circuit have been as a result of both innovation and the application of technological improvements. Improvements have been made to the flotation, roasting and CIL circuits and RML has introduced a deslime circuit to treat flotation concentrate, in addition to the very successful commissioning of a new 1 Mt/a oxide circuit in December 2014. These changes have resulted in gold production increasing to more than 20 000 oz per month in 2015.This paper presents the processes, change implementation and outcomes of the modifications made to the sulfide circuit to address the availability and recovery problems.Apart from the expansion of an existing, world-class deposit and discovery of new resources, future improvements on the path to a class-leading gold mine include the continued reduction of the unit cash cost, increase in overall sulfide circuit gold recovery, increased throughput through continued innovation and consistency in the plant’s operation.Citation:Sinclair, R, Hunter, I and Landwehr, D, 2016. Syama Gold Mine - the Journey towards a Class-leading Gold Mine, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 213–224 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D J. Brake

The risk from fire remains one of the most serious of underground mine disaster scenarios. The impacts of mine fires on the underground ventilation system and the production of toxic gases have been difficult to model and therefore assessments have relied largely on empirical data, historical precedent and subjective opinions. Underground fire modelling software has had limited availability and been technically challenging and time consuming to use especially for routine mine investigations. There has also been no well-accepted set of assumptions for fire modelling in mines, which has resulted in a lack of confidence in adopting its use more widely. This paper describes modelling of three critical fire scenarios in underground hard rock mines: a fire (LHD) in an underground diesel refuelling facility, a fire in an underground explosives magazine and a fire on an underground ore transport conveyor. Modelling was undertaken using VentsimÆs VentFIREÖ fire simulation module. It describes the basis of design, the key assumptions, the methodology used and provides examples of the outputs, conclusions and recommendations. It reviews the impacts of these fires on egress and entrapment strategies in the mine. Some general principles regarding improvements to ventilation circuit design based on this analysis are also recommended. Whilst the fire scenarios were based on actual case studies, they have been disguised for this paper.CITATION:Brake, D J, 2013. Fire modelling in underground mines using Ventsim Visual VentFIRE software, in Proceedings The Australian Mine Ventilation Conference , pp 265-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By B Levasseur, C Olsen, E Ghasemian Langeroudi, F Larachi, F Safizadeh, C Gagnon

Gold recovery by the cyanidation process is often accompanied by the leaching of other species. This leads to the depletion of the level of free cyanide and oxygen available for gold cyanidation. The largest proportion of the consumed cyanide is diverted by the cyanicides (eg S, Cu, Zn, Fe, etc) into non-valuable complexes.COREMÆs Extractive Metallurgy team has been conducting a research program on the improvement of the gold cyanidation process. As a part of this program, the current study aims to investigate the effect of certain operating parameters on the reactions involved during preoxidation and cyanidation. Flotation tailings and single mineral samples such as pyrite, sphalerite and chalcopyrite, along with their different combinations, were analysed to highlight the influence of ore mineralogy on the operating conditions. The effects of different kinds of oxidants (oxygen, hydrogen peroxide, ferricyanide and ozone) and chemical additives (ammonium sulfate) were investigated.Experiments conducted in alkaline solutions reveal that mineralogy is a key parameter since pyrite, chalcopyrite and sphalerite react quite differently during preoxidation and cyanidation. A significant increase in sulfur dissolution, especially on pyrite, was observed by applying preoxidation. H2O2 preoxidation showed a positive effect on increasing sulfate formation, a desirable by-product from the cyanide consumption point of view. Preoxidation of synthetic ores with ferricyanide resulted in boosting thiosulfate formation. Tests conducted on flotation tailings from a polymetallic mine revealed that a short preoxidation increases the dissolution of the ore leading to higher gold recovery and lower cyanide consumption. Regarding the formation of thiocyanate, the most undesirable by-product of the cyanidation, ferricyanide and ozone were found particularly efficient to hinder their formation. Finally, the addition of ammonium sulfate during the cyanidation process showed some promising results in terms of both gold dissolution and cyanide consumption.CITATION:Ghasemian Langeroudi, E, Levasseur, B, Safizadeh, F, Olsen, C, Larachi, F and Gagnon, C, 2013. Optimisation of operating parameters for cyanidation of sulfide-bearing gold flotation tailings in order to prevent the impact of cyanicides, in Proceedings World Gold 2013 , pp 111-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A Ross, B De Rivaz

The results of full-scale tests on precast segment made at University of Roma are presented. The segments were cast using fibre-reinforced concrete produced without any traditional reinforcement, by using fiber made in high-strength steel and a new type of anchorage.Bending tests were performed in order to check the bearing capacity of the segments under the flexural actions; these occur during de-moulding, handling, storage phases as well as in the in situ condition (due to asymmetric soil pressure). Furthermore, point load tests simulating the TBM thrust were performed, in order to study the construction phase (excavation).The results show that the segment response largely respects the material testing and design advice according to the Fib Model Code 2010. Providing engineers, precast operators and builders confidence in material strengths and design methodology.CITATION:De Rivaz, B and Ross, A, 2014. Full-scale tests on precast tunnel segments made in concrete reinforced with high-strength steel fibres, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 469–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Scoble

This paper addresses the importance of collaborative approaches to resolving future mining challenges. It attempts to provide some insight into understanding the theory, measurement, mapping and management of collaboration. This is related to the design and planning for successful research and educational initiatives. Reference is made to Canadian and global case studies and personal experiences.

Nov 22, 2011

By K Rees

In the ideal world of an underground mining engineer, all narrow vein orebodies would be perfectly straight and continuous, thus would be a dream to mine. However, this is usually not the case. Narrow vein orebodies generally occur in association with shear zones and while shear zones do form linear trends, they most commonly preserve undulating expressions that need to be closely monitored, particularly when overprinted by post-formed structures. The surge in mines using fibrecrete as a primary form of ground support effectively reduces the time available for geological interpretation down to a 30 minute window between bogging and shotcreting. Thus, if the quality of the data collected is not up to scratch, then there is only a limited ability to reassess using 2D face photographs. To negate this, Xstrata Nickel AustralasiaÆs Cosmos mine has upgraded its data collection procedure. Geological information is now collected using photogrammetry survey, producing 3D images of the drive. Once created, the digital image of the drive is loaded into Vulcan, thus enabling geological interpretation to be carried out along entire drives, between levels and in association with all other data (eg drill holes, seismic data, etc). In addition to this, the 3D image can be used to accurately model the location of the ore, enabling stoping panels to be confidently positioned to maximise grade and minimise dilution. However, with the focus at Cosmos changing from narrow vein mining, to bulk mining methods in a more geotechnically complex terrain, the use of the 3D images has become paramount in understanding the structural geometry. Continual interpretation of the data has enabled drive profiles to be maintained through the increased use of ground support in poor ground and the redesign of development to enable optimal intersection of structures. Nevertheless, while the collection of quality data is important, it is only the effective use of the data, which enables significant gains in understanding.CITATION:Rees, K, 2012. The benefits of using photogrammetry in the geological interpretation of the Cosmos nickel mine, in Proceedings Narrow Vein Mining 2012 , pp 145-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By N Jeannee, L Rattmann, M W. N Buxton, A deJong, K Nienhaus, A Soares, P Graham, A Korre, J Benndorf, D Buttgereit

The flow of information, and consequently the decision-making along the chain of mining from exploration to beneficiation, typically occurs in a discontinuous fashion over long timespans. In addition, due to the uncertain nature of the knowledge about deposits and the inherent spatial distribution of material characteristics, actual production performance often deviates from expectations. Reconciliation exercises to adjust mineral resource and reserve models and planning assumptions are performed with timely lags of weeks, months or even years.The key concept of real-time mining promotes a change in paradigm from discontinuous intermittent process monitoring to a continuous process and quality management system in the resource extraction process. The framework includes a real-time feedback control loop that rapidly links online data acquired during extraction at the mining face, material handling and processing with a sequentially updatable resource model. This will allow near real-time optimisation of decisions related to long-term planning, short-term sequencing and production control.The proposed framework integrates the following building blocks in a holistic manner: automated sensor-based material characterisationonline machine performance measurementsunderground navigation and positioningunderground mining system simulation and optimisation of planning decisionsupdating techniques for resource/reserve models.This paper introduces the real-time mining concept and the building blocks and provides a review of the state-of-the-art. Technological readiness of necessary building blocks is assessed, and critical gaps for further technology development are identified. The value added is illustrated by means of a case study.CITATION:Benndorf, J, Buxton, M W N, Nienhaus, K, Rattmann, L, Korre, A, Soares, A, deJong, A, Jeannee, N, Graham, P, Buttgereit, D, Gehlen, S, Eijkelkamp, F, Mischo, H, Sandtke, M and Wilsnack, T, 2015. Real-time mining – moving towards continuous process management in mineral resource extraction, in Proceedings Third International Future Mining Conference, pp 37–46 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Y Zhang, Z Zhao

The green production of the steelmaking process has urgent requirements for fluorine-free fluxes. In this article, a new solid waste-based slagging flux was applied in the external dephosphorisation test of low silicon hot metal to replace the traditional fluorite-lime dephosphorisation slag. The results showed that under laboratory conditions, the new flux was utilised for smelting low-silicon molten iron with a phosphorus content of 0.10~0.13 wt per cent, the temperature of the molten iron was 1350°C and the slag amount was controlled at 2 per cent. Within ten minutes of smelting, the dephosphorisation rate of the molten iron reached more than 50 per cent. When making slag with new flux, the slag melting time was about 40 seconds and the P2O5 content in the final slag was higher than 8 wt per cent. In the industrial test of a 150 t molten iron ladle, under the same molten iron conditions, an out-of-furnace dephosphorisation test was conducted in the Kambara Reactor (KR) process. The flux material consumption per ton of steel was 8~10 kg. Within 15 minutes of smelting, the dephosphorisation rate of the molten iron was about 30 per cent. During flux slag making, the slag melting time was about three minutes and the P2O5 content in the final slag was higher than 6 wt per cent. This new solid waste-based flux has significant cost advantages and outof- furnace dephosphorisation effects and is expected to become the benchmark for a new generation of fluorine-free steelmaking fluxes.

Aug 21, 2024

By D Kentwell

A resource model serves two main purposes depending on the stage of a project. The first is to provide an early indication of likely tonnages and grades at certain cut-offs so that decisions can be made on whether continued spending on the project is justified. The second is to provide a basis for mine planning, feasibility studies and reserves. Resource models are not designed for selection of actual blocks in the ground for processing. This is the purpose of a grade control model, which is created at a stage beyond both resources and reserves.Inferred, Indicated and Measured Resources contain different levels of uncertainty with respect to the accuracy of the resulting grade and tonnage curves. These uncertainties arise from three broad areas: quality of information, geological assumptions and estimation technique. This paper focuses on known problems with the ordinary kriging (OK) estimation technique. Resource estimates often produce smoothed block grade distributions with much lower block grade variability than true selective mining unit (SMU) block grade distributions. There are two main factors that are involved in this smoothing. Firstly, where the block size used for estimation is larger than the SMU block size, this will smooth the block grade distribution and move the grade and tonnage curves away from the true SMU block grade and tonnage curves. Secondly, and less well recognised, is that smoothing is inherent in the OK estimator. This also moves the grade and tonnage curves away from the true SMU grade and tonnage curves, even when the estimate is done at the SMU block size. There are a number of techniques, such as simulation, uniform conditioning and degraded search neighbourhoods that can provide a better approximation of the true SMU block grade and tonnage curves at the expense of individual block accuracy.This paper aims to explore the extent to which OK resource estimates designed to maximise individual block accuracy can differ from (an estimate of) the true resource at SMU block size in terms of grade and tonnage curves. The differences at economic cut-offs and above are examined. In some cases these differences are significant. Both the OK estimation technique and block size play a part in the differences observed. To do this we will examine a number of commodities and deposit types using real project data.The conclusion is that the current industry standard default practice of targeting maximum individual block accuracy (conditional unbiasedness) using OK at resource stage, without consideration or evaluation of the extent of associated smoothing at SMU scale, can lead to significant errors in fundamental mine planning decisions. This then has implications for resource classification if the classifications are based heavily on the OK quality without consideration of the true SMU distribution.CITATION:Kentwell, D, 2014. Aligning resource estimates with mine planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 185–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By H Tran

Local communities are undertaking an increased role in mine project decision making processes, associated with growing pressure and expectations from regulators, financiers and the general public. This is particularly evident in international projects within developing economies. Environmental and social issues are often complex. Solutions demand difficult choices and trade-offs between sustainable development dimensions: economic growth, social equity and environmental integrity. Proactive stakeholder engagement can play a critical role in assisting decision-makers in determining the operational reality of sustainable development by jointly exploring project trade-offs between proponents and affected stakeholders. Good stakeholder engagement has other potential benefits, ranging from reduced financial risk due to regulator delays, legal disputes or negative publicity to increasing market share through good public image. Approaches to consultation and disclosure have changed from short-term regulatory based focuses, to longer-term, strategic tools for relationship building, proactive risk management and new business identification. Approaches to consultation form a significant opportunity to contribute to overall social sustainability. This paper discusses, based on authorsÆ experience, the broader concept of stakeholder engagement and its contribution to social sustainability of the mining industry. The focus is on key considerations for an effective stakeholder engagement. Three case studies outline how broad based, proactive stakeholder engagement can contribute to improved operation and overall sustainability. The case studies include: a greenfields project in Ghana; a long-term mine in Australia; and an open-pit mine in Vietnam.

Jan 1, 2009

By Y Li, Z Fu, D J. Williams, E Topal

Mine waste rock is unavoidable in the recovery of ore by open pit mining methods. Effective management of waste rock movement covers the removal and placement of the waste rock, generally in a surface dump in the most cost-effective way while satisfying the long-term environmental expectations. Since the 1960s, there has been significant research carried out into planning of ore movement from open pit mines such that the overall net present value (NPV) of the project can be maximised. Currently, several software packages are available to achieve this task as a common practice within the mining industry. However, planning of mine waste rock movement is still achieved manually, as the available software does not consider optimal waste rock movement and dump design. This paper describes a tool to optimise waste rock placement, which minimises the haulage cost while creating environmentally friendly waste rock dumps through selective placement and encapsulation of the reactive waste rock in the dump. The embedded methodology in this tool has been developed based on the mixed integer programming (MIP) modelling technique to optimise the waste rock movement. The methodology provides an easily-manipulated and fully-automatic tool for professionals to complete waste rock dump scheduling in four main steps: data input, model construction, model computation and solution retrieval. The application of the new tool into a real case project in this paper shows that it can determine economically and environmentally optimised waste rock dump schedules in an acceptable time frame.CITATION:Fu, Z, Li, Y, Topal, E and Williams, D J, 2015. A new tool for optimisation of mine waste management in potential acid forming conditions, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 333–342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Zhang, B Wei, T Zhao, K Wang

Understanding mining-induced surface movement and fissures is critical for environmental protection and geological prevention. In this study, image recognition algorithms, satellite remote sensing and unmanned aerial vehicle photogrammetry (UAVP) were combined to identify surface movement and fissures caused by mining, and a case study was conducted in a coalmine in western China, and the following conclusions were obtained.

Sep 1, 2024