Search Documents

The Ortiz Mountain property is located approximately 40 km (25 miles) southeast of Santa Fe and 13 km (8 miles) from the village of Cerrillos. The property embodies a Spanish mineral grant from which Gold Fields acquired about 2, 200 hectares (900 acres of surface and mineral rights. Following a period of exploration, metallurgical testing and development of a feasibility study in 1974, the decision was made, because of the higher gold price in the fall of 1978, to place the property into production. the gold is confined in a quartzite breccia; it is an unusual occurrence because the gold in this host rock is leachable at minus 19 mm (3/4 in. ). Total ore reserves are estimated at approximately 3.6 million mt (4 million st) averaging 1.89 g per mt (0.055 oz per st) based on a cut-off of 0.7 g (0.02 oz). The ore will be recovered by open pit mining at a stripping ratio of 1. 2:l. Production is scheduled for 13,600 mt (15,000 st) of ore per week or approximately 680,000 mt (750,000 st) per year. Primary crushing of pit-run material is by a 1,070 by 1,015 mm (42 in. by 40 in.) jaw crusher. Crushed ore is conveyed to stockpile and then to a 2.13 m (7 ft) standard crusher with the screened over- size crushed in a 1.5 m (5 ft) tertiary cone crusher. The screen undersize, the final product for leaching, is minus 19 mm (3/4 in. ). A 1, 360 kg (3,000 lb) sample is cut from the crushed ore stream, further crushed in a small jaw crusher and then sampled in two more stages by Vezin samplers to produce a final 13.6 kg (30 lb) sample for assaying. Pebble lime is then added to the ore on the belt as it is sent to the conveyor gantry spanning the leach pads. A tripper on this moving gantry stacks the leach ore without compaction. The entire crushing plant and conveying system is of open-air construction. Leach pads have a total length of 515 m by 60 m (1,700 ft by 200 ft) wide with usable dimensions of 490 m by 58 m (1,600 ft by 190 ft). The directional length slope is 3. 870 with 370 on the width. The pad is constructed of 175 mm (7 in. ) thick asphalt containing a rubberized asphalt membrane. It is divided by a 300 mm (1 ft) high curb into eight segments. Each segment is loaded with 13,600 mt (15,000 st) of ore, which is one week's production. Optimum working height of a pad is considered to be 3. 0 m (10 ft) with a maximum height of 4. 0 m (14 ft).

Jan 1, 1981

By W. A. Backofen, A. T. English

The kinetics of re crystallization were determined metallographically for a 3-1/4 pcl Si-Fe rapidly compressed at temperatures of 710° to 911°C, and held for various times at the working temperature. As in re crystallization following cold wwk, the time for re crystallization was reduced by increased temperature and strain. Nucleation occurred chiefly at grain edges, although other pre-existing interfaces, notably inclusions, also served as nucleation sites. The importance of intragranular nucleation to grain refinement in hot working is pointed out, together with some possible techniques by which nucleation might be induced within the grains. The observed isothermal growth rates are quite accurately described by the equation G = 4 x 10-'/t (cm per sec), independent of temperature and strain at all but the shortest times. Changes in G during recrystalliza-tion can exceed two orders of magnitude. It is argued that release of stored energy associated with lattice defects cannot adequately explain the time dependence. A suggested alternative involves processes of solute segregation and desegregation in the unrecrystallized matrix and at the moving boundary, respectively. EFFORTS to improve hot-working practice are hampered by an incomplete understanding of the fundamental metallurgy involved. Research directed at establishing the required basic foundation falls into two categories, the first concerned with measurement of mechanical properties under the conditions of high temperature and strain rate which characterize such processing, the second focused on structure and its relation to the deformation conditions. Rossard,' Rossard and Blain,2 and Hardwick and Tegart have conducted many high-speed, high-temperature torsion tests on various metals. One of their objectives was interpretation of stress-strain curves in terms of the structures of specimens rapidly quenched following interruption of twisting. They showed that appreciable hardening occurred in the early part of the test, and that this hardening reflected the concurrent development of an increasingly dense substructure within the grains. The detailed nature of this substructure was observed to depend on the ease of polygonization which, at least in fcc metals, varies with the stacking-fault energy.= By holding specimens after interruption but before quenching, the nucleation and growth of new grains could also be studied. Some success has been realized in relating the microstructure of hot-rolled steel to its temperature:strain rate:strain history with such testing.' The same general observations have been made by others investigating rolling4f5 and drop-hammer forging.~-~ Incident to these experiments, some efforts were made to determine the kinetics of re-crystallization as well as the velocity of the migrating boundaries. The results have been largely qualitative, owing to difficulties of interpreting hardness measurements5 and microstructures. The work described here was undertaken to obtain more quantitative information from tests on a material having suitable metallographic properties, and, in this way, to provide further insight into the fundamentals of this practically most important kind of deformation processing. I) MATERIALS AND EXPERIMENTAL TECHNIQUES Materials. Electrolytic etching of a Si-Fe alloy reveals dislocations and substructure in unrecrystallized grains.8'9 This unique characteristic makes possible a precise determination of the extent of recrystallization. For that reason, it was the material selected for all experiments in the present work. The two particular alloys that were used are identified in Table I. A major difference between "A" and "B" is the number of inclusions, as noted in the table. Most of the experiments were made with material "A". It was received as hot-rolled plate 1 in. thick, sawed to 2-in. widths, hot-forged at 1200°C to 5/8-in. rounds, and finally annealed in a mechanical vacuum at 1000°C for 24 hr. The result was substructure-free grains of mean diameter 0.05 cm.*

Jan 1, 1964

By Duk-Won Park, Syd S. Peng

INTRODUCTION More than five years have elapsed since the first shortwall panel was installed in a US mine in 1972. By the latest count, 11 mines have tried the shortwall method on 34 panels. Potentially, the shortwall method (see Figure 1) offers the combined advantages of longwall and continuous mlning. But just like any other mining method, shortwall is not a panacea. It is only applicable under a set of stringent conditions. Coal operators at eight of the eleven mines are satisfied with shortwall mining, though there are only five mines presently producing coal from shortwall panels.

Jan 1, 1981

By William B. Phillips

The possible sources of potash salts in the United States have been considered from many points of view during the last several years, but it is only within the last two or three months that the situation has become acute. We import from Germany, the only sourcc of large supply, more than $10,000,000 worth of potash salts annually, and this business has been badly crippled by the European war. If there was ever a time in our industrial existence when the necessity of providing for our own needs was more acute than it is now, we are not aware of it. One has only to study the price lists of chemicals sent out by the large supply houses to see the change wrought within a very short time. Whether or not these prices are to maintain for a considerable time, no one can say; but it appears to be probable that we shall not see prices materially lower for a period of uncomfortable length, to say the least. It is not my purpose at this time to discuss the various sources of supply of potash salts that have been suggested or recommended. Some of them might afford a pleasing relief but all of them combined would not affect the situation seriously. If we are to have our own sources of potash salts, they will have to compare, in some efficient manner, with the sources upon which we have drawn during the last 20 or 30 years; i.e., they must exist in minable quantities. It seems to me to be quite idle to speculate upon our domestic sources of potash if those sources are not of a character similar to those upon which we have so long depended. A few thousand or, perhaps, a few hundred thousand dollars' worth of chemically derived potash may be produced under the stress of present conditions, but when we consider that each year demands more than $10,000,000 worth, we must look to underground sources; we must look to mines similar to the famous Stassfurt and Halle deposits. If we cannot mine potash salts, we shall have to do without them for a while.

Jan 1, 1915

By James F. Kemp

In earlier gears, the custom prevailed of regarding the anthracite basins as cases of folding with slight development of faulting. Folding is so pronounced and, in the eastern and western Middle Fields, at times so violent, that the inference was a natural one and led to the widespread impression that practically all the disturbances of the seams could be explained in this way. The cross-sections and maps prepared forty or more years ago for the Second Geological Survey of P ennsylvania, by Mr. Ashburner under Prof. J. P. Lesley, exhibit little else than folds.' So far as I can discover faults fail in the charts, except in one small case in the Henry colliery near Plainsville on the outskirts of Wilkes-Barre. Some years ago, while spending a day or two in Wilkes-Barr, under the guidance of R. V. Norris, I looked over some recent and accurate cross-sections of a numbcr of the large collieries and was deeply impressed with the peculiar behavior of some of the seams and the intervening shales. Thus, a seam might present a small, more or less overturned fold, rising 30 to 50 ft. (9 to 15m.) above its general course, and yet the movement would be taken up in the overlying shales, so as hardly to be noticeable in the seams next above or below. These and similar anomalies, especially when shown with the accuracy of engineer's surveys, possess great scientific and practical interest, bearing as they do, not alone on coal mining, but on theoretical geology and the actual behavior of strata under great compressive stresses. In preparation for the semicentennial meeting of the Institute, an effort was therefore made to secure some of the most interesting sections for presentation to the members. The collection of illustrations here shown is mainly due to Douglas Bunting of the local committee, to whom and to the contributing companies acknowledgments are due. The illustrations are taken from all four of the main basins, but are chiefly from the portions nearest Wilkes-Barre. The first are in the

Jan 1, 1922

By Henry G. Granger

A residence of 14 Sears in the Republic of Colombia, spent . in almost continuous traveling and prospecting-trips, has given me an intimate knowledge of the resources of that wonderful country. The man who best knows Colombia is unquestionably General Rafael Reyes, President of the Republic for the past three years, and with seven years more to serve in his present term. Such is the strength of his personality and the wisdom of his policies that his term of office will no doubt endure as long as he is milling to serve. The vastly improved economic situation and the brilliant outlook for Colombia are so directly due to the influence of President Reyes that a few lines concerning him will not be amiss, if they serve towards a better understanding of his personality. Born of a distinguished ancestry in the mountain~ of Boyaca, he is now 57 years old, just the age of his friend Porfirio Diaz when he began the work which has placed Mexico in the rank of great modern nations. It was Reyes who came to Washington to protest against the action of the government of the United States of America in

Jan 1, 1909

By S. A. Braley

DRAINAGE water from coal mines is probably the most serious water pollution problem today, varying in importance according to location of the mines and geological structure. Drainage may be either acid or alkaline in character. Acid discharge, the most severely detrimental to a stream, is caused by natural oxidation of the sulfuritic material (FeS2) in the strata associated with the coal seam. Since the acid is the result of a natural reaction the acid water differs because it does not cease with abandonment of the mining operations. There is no known economical method of neutralizing acid mine water or any practical method to prevent oxidation of exposed pyrite. Since production of acid from a mine does not stop when mining stops, the total quantity produced depends entirely upon the excavated areas. The increasing volume of acid water in manv mines has greatly increased operating costs. Pumping is expensive and acid mine waters are destructive of all equipment, especially metals in pumps and piping, and necessitate the use of corrosion-resistant materials. Discharge of the acid mine drainage into streams neutralizes their normal alkalinity, causes them to become acid, and produces an environment unfavorable for aquatic life and unsuited for industrial or domestic use without costly treatment. Mine drainages vary in percentage composition over wide limits, although the usual dissolved substances are ferrous and ferric iron, aluminum, calcium and magnesium sulfates, and lesser amounts of sodium, potassium and manganese sulfates and chlorides. Some alkaline discharges may contain heavy concentrations of iron as iron bicarbonate. These waters may produce iron hydroxide deposits in the receiving stream but do not cause it to become acid. In the extensive literature on acid mine water there appears to be a great deal of confusion about the importance of various components and the methods for their determination. In many instances faulty conclusions have been drawn from use of unsuitable methods of analysis. It is desirable that the factors and terms used in evaluation of analyses of mine waters should be so clearly defined that any interested person could properly appraise any analytical report. Some analysts report complete chemical analyses of mine waters and neglect to record drainage volumes. Others report only a minimum of analytical data after taking no precautions to preserve the original composition of the water during the time elapsing between collection and analysis. Some use methods of analysis intended for so-called pure waters of the potable and boiler water classes. These methods are not applicable to highly buffered waters such as mine water. Probably the most common criteria for evaluation are pH, free acidity, or acidity or alkalinity to methyl orange or methyl red, total acidity or acidity to hot phenol-phthalein, and the sulfate content. If these determinations are made on carelessly collected samples after a few days to weeks standing in warm rooms, they do not in any way represent the character of the water flowing from the mines. It is hoped that a brief discussion of the fundamental value of some of these factors may lead to a bettqr understanding of the need for more careful evaluation of mine water discharges. The term pH is one used by chemists to express relative acidity or alkalinity in terms of concentration of effective hydrogen ion in a solution. It is defined as the negative logarithm of the hydrogen ion concentration or activity in equivalents per liter. pH = logarithm A neutral solution, which is one containing the same number of hydrogen and hydroxyl ions, has a pH of 7. As the hydrogen ions increase and the solution becomes more acid, the pH decreases toward zero; and as the hydroxyl ions increase and the solution becomes more alkaline, the pH approaches 14. When dissolved in water to a dilute solution acids like sulfuric and hydrochloric, commonly known as strong acids, ionize completely, and the pH or hydrogen ion concentration varies with molar concentration of the dissolved acid. However, in high concentrations of such acids, the pH or hydrogen ion concentration is less than the acid concentration because the acid does not completely ionize. In only very dilute solutions does the pH represent the total amount of acid that can be neutralized by an alkali. All ionization reactions are equilibrium reactions. If other chemicals are added to the solution of an acid and the added chemical produces an ion that is the same as one of the ions of the acid, the degree of ionization of the acid is altered and the pH changes to some value that represents the active hydrogen ion of the new solution. Thus if iron sulfate is added to a solution of sulfuric acid the pH increases, since the common sulfate ion suppresses the degree of ionization of the sulfuric acid and decreases the effective hydrogen ion. However, the total acidity of the solution is increased. There are two salts composed of iron and sulfate— ferrous and ferric sulfate. In these salts there is no hydrogen ion that can ionize to give an acid solution, but when they are dissolved in water, the pH is less than 7 and the solution becomes acid. This is caused by a reaction known as hydrolysis and is represented by the equations FeSO4 + 2H2O ? Fe(OH)2 + 2H + SO,: or Fe,(SO,)3 + 6H2O ? 2Fe(OH)3 + 6H+ + 3504 A solution with a total acidity of 5000 ppm according to the first equation will have a pH of 4.40 but one with an acidity of 75 ppm, according to the sec-

Jan 1, 1958

By Frank Firmstone

When in charge of the Glen don Iron Works, the importance of good methods of filling was forcibly brought to my attention, and it occurred to me that the first step toward the discovery of the best plans was the accumulation of exact information as to the distribution actually effected by various chargers; also, that something could be done in this direction by careful measurements in the furnace, to be afterwards recorded for comparison on drawings. The figures shown herewith have been prepared from such measurements, and nearly all of them refer to Glendon, where the fuel used was anthracite and the ore-mixture about threequarters of New Jersey magnetic ores and one-quarter of brown-ores from the vicinity of the works. Every occasion furnished by the blowing-in of furnaces was utilized, but the data accumulated rather slowly in this way; and, opportunity oEering to make special trials at no great expense, the figures from 2 to 7 were thus obtained. The trials were made by dumping a hopperful (6 barrows) of material at once into the furnace, and, when all the fuel of a round (12 barrows) had been put in, the profile of the upper surface was obtained by stretching a steel tape across the top on a diameter and at a known height. By measuring down from this with a graduated rod, the profile was easily obtained with sufficient accuracy, especial pains being taken to get correctly the crests of the ridges and the bottoms of the hollows, as many intermediate points being included as seemed necessary. This was repeated on another diameter when there was occasion. The same course was followed for the limestone and ore.

Jan 1, 1899

[Abad. Leopoldo F., Min. Engr., Div. of Mines, Bureau of Science Manila, P. 1. '28 Abadilla, Quirico A., Geol., Lago Pet. Corp Box 172, Maracaibo, Venezuela. '20 Abarquez, Ramon F., Met., Bureau of Science Manila, P. I. '24 Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio. '21 Abbott, A. N., Mines Supt.. Mazapil Copper Co,, Ltd Concepcion del Oro, Zac,, Mexico. '28 Abbott, Clarence E., Mgr,, Mines & Quarries, Tenn, Coal, Iron & R. R. Co., 1242 Brown Marx Bldg,, Birmingham, Ala. '04]

Jan 1, 1928

By E. A. Gulbransen, K. F. Andrew

THIS paper. will present the results of our studies on the kinetics of the gas phase reactions of co-lumbium and tantalum with O2, N2 and H2. Studies on zirconium and titanium have been previously reported.9,11 Due to their high melting points and their many excellent physical and chemical properties, colurn-bium and tantalum have been finding their places as useful metals in science and industry. Chemically the metals are very inert to gas and liquid phase corrosion at room temperature. However, at moderate temperatures of 250°C and higher the metals react readily with oxygen and hydrogen. It is of interest to study the gas phase reactions of these metals for the following reasons: (1) to compare the rates of the several reactions with those of other metals and to correlate the rate data with theory and structure predictions, (2) to add basic information on the practical difficulties of the reduction, refining and working of columbium and tantalum, (3) to anticipate new uses for the metals and (4) to understand the role that the metals play as components in high temperature alloys. Literature Survey A number of papers exist in the literature on the gas phase reactions of columbium and tantalum with O2, N2 and H2; however, only fragmentary data have been reported on the kinetics of these reactions. Although the free energy of formation of the oxide Ta2O520at 25°C has been determined and some thermodynamic work has been reported on columbium and its oxides, the data are not sufficient to make equilibria calculations at elevated temperatures. Oxidation: 1. Kinetics: The rate of oxidation of columbium and tantalum has been studied by McAdam and Geil23 using the interference color method. Tantalum is reported to oxidize more slowly than columbium, zirconium and iron. The amounts of oxidation of columbium after 20 hr in air for several temperatures are reported by the Fansteel Metallurgical Corporation.36 Columbium starts to oxidize in air at about 200°C. The oxide is said to be adherent and prevents further oxidation until the temperature is raised. Columbium is reported not to become brittle on heating in air for short periods like tantalum because the oxide film prevents further reaction. The columbium oxides dissolve into the metal when heated in a vacuum at temperatures between red heat and 1200°C. Above 1200°C the oxides are reported to evaporate. Columbium, in the oxide free state, is an active getter in vacuum tubes. 2. Preparation and Structure: G. Grube, O. Kuba-schewski and K. Zwiauer15 have studied the decomposition of Cb2O5 in argon. They find that CbO2 is formed slowly at 1150° and rapidly at 1300°C. Cb2O5 can be reduced to CbO2 by moist H2. The reduction of this dioxide to the lower oxides is rapid. By varying conditions CbO2, Cb2O3, CbO and Cb2O can be formed. CbO2, CbO and Cb2O have independent lattices while Cb2O3 is a stoichiometric mixture of CbO and CbO2. In a later paper O. Kuba-schewski" has shown that CbO is cubic and that CbO2 has a rutile type of lattice. The most exhaustive work on the oxides of columbium is that of G. Brauer.8 The number and constitution of the solid phases in the binary system Cb-O were investigated by the preparative, analytical and X ray methods. He indicates that only the oxides Cb2O5, CbO2 and CbO exist with limited regions of homogeneity. The solid oxide Cb,O, exists

Jan 1, 1951

By Frank Tolonen

IRON-ORE beneficiation is becoming of vital importance to the Lake Superior region, since only a few decades will be needed to exhaust the direct shipping ores even if generous allowances are made for discoveries of new orebodies. If the region is to continue as the chief source of ore to the steel industry of the United States, it must concentrate or otherwise beneficiate the enormous tonnages of available iron formations. A beginning along this line has already been made. About one-fifth of the total shipment, even now, is the product of some sort of concentrating process, while another fifth is improved in physical structure by crushing, screening, drying, sintering, or some other similar method. The amount of material amenable to these processes is limited, however; and, in order to be able to utilize the billions of tons of iron formations that cannot be so beneficiated, an intensive study of their nature and concentration possi-bilities is necessary. As long as high-grade ores are available in ample quantities, ore dressing is economically impossible, but as soon as the supply nears exhaustion it becomes necessary. At first the products of ore dressing must meet as nearly as possible the same specifications as the rich ores in order to be adapted to the reduction processes already established. The future requirements as to quality will depend on the one hand upon the ability of the ore dresser to eliminate undesired constituents and charac-teristics in the material, and on the other upon the adaptation of the reduction processes to the product that can be economically supplied. A better understanding of the blast furnace and other reduction reactions, and improvements in the preparation of raw materials, should enable the Michigan districts to continue to supply ore for a long time to come. The study and testing of the iron formations necessary to bring a utilization of the low-grade ores, though requiring time and effort on the part of all concerned, should not be postponed, especially since the economic situation forces the use of the highest grade ore in preference to the leaner material.

Jan 1, 1933

By Lawrence K. Jetter, Robert F. Mehl

SOME advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory.? Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selected for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatometric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system-a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation ;2,3,4 there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type-the ideal case which Becker5 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1942

By Maurice Grieves

The great majority of shafts constructed today are still excavated by drilling and blasting, a method which changed very little in over 100 years until the introduction of the mechanical lashing unit and cactus grab by the South Africans, which enabled muck to be removed as fast as massive hoisting systems could handle it and resulted in very rapid rates of sinking. Record breaking month's performances were achieved at -Hartebeestfontein No. 4 shaft, October 1960-337.1 m; Western Reefs No. 4 shaft, October 1961-340.7 m; and Buffelsfontein eastern twin shaft, March 1962-381.2m. The method was very labor-intensive, requiring a crew of over 60 workers at the shaft bottom during the drill cycle. Safety precautions were strict, but in the drive to achieve rapid advance, cases of personal injury were still somewhat high because of the large number of people engaged in this potentially hostile environment. The South African method, as it came to be referred to throughout the rest of the world, was adopted in the United Kingdom in the late 1950s in a modified form with greatly reduced manpower and nonsimultaneous sinking and lining, which was insisted on by the British Mines Inspectorate. In that instance, it was successfully used to sink the 7.3-m-diam concrete-lined shafts at Kellingley to 770 m depth, with rates of advance of over 90 m/month achieved, a British record at that time. During the sinking of the 1.15-km-deep twin shafts at Boulby potash mine in the UK in 1970, the method was again used, but for the first time ever in Britain exemptions from the mining code permitted the use of crash beams, crash doors, jack catches, and semi-simultaneous sinking and lining techniques. New British shaft sinking records of over 120 m/month were achieved in both shafts. Similar equipment and techniques were used in the early 1970s to sink several deep shafts in Canada, notably Creighton #7 and the Con zinc mine at Yellowknife in the NW Territories. Today, this equipment is standard for deep shafts in the US and the rest of the world. However, with the tremendous escalation in mining labor costs, the impact of health and safety legislation, and environmental regulations, coupled with a very real shortage of miners willing to work in this exposed situation it was apparent that an alternative to the labor-intensive conventional method of shaft construction had to be found. Recognizing the trend is inevitable, one or two major German shaft sinking contracting firms began to take a fresh look at full face boring techniques applied to tunnels and raise bored shafts. The results were most encouraging. Tunnel drivage techniques using moles had developed considerably from Colonel Beaumont's original channel tunnel machine circa 1880 to the superbly engineered Priestley machine selected to cut the British side in 1975 and the double shielded Robbins Grandori borer on the French side of the English Channel. Full face tunnel machines were being successfully used to drive uphill in inclined shafts in Austria and Switzerland. At Mapprag in Switzerland, the Demag mole drove the first (intentional) vertical transition and curve, and then went on to successfully complete the 730-m-long penstock shaft at an inclination of 35°. In Austria, the Wirth mole drove the Kaprun Glacier ski-lift railcar tunnel at record breaking rates of 457 m/MONTH (best 30 m/d) through green schist at an inclination of 29° for a distance of 3.35 km while the Hydro tunnel at Sarrelli in Switzerland was being driven by the Robbin's mole at an inclination of 35°. Simultaneously, extremely promising results were obtained using large assemblies of cutter discs on raise borer heads, such as the 4.87-m-diam X 460-m-deep shaft raised by Teton for Jim Walter Resources Inc. Bearing in mind that most mine shafts in the future (unless in exceptionally competent rock) will require some form of lining, and the trend will be toward deeper shafts as the more easily accessible mineral deposits become exhausted, it was seen that normal raise boring had definite limitations in vertical accuracy, in the limitation imposed by the drill string on the available torque that could be applied to the cutter head, and in the risk of collapse of the unsupported shaft rock wall in friable or jointed and fissured ground, since it is not possible to apply any form of temporary support until the permanent lining is being installed. A further problem was the economics of installing a subsequent lining, necessitating setting up a headgear and hoisting arrangement approaching in size that required for conventional drill and blast sinking and lining. Because of the economics, German contractors opted for a phased transition from drill and blast to the full face, rodless, out of the solid shaft mole, by starting off with a down-the-hole shaft boring machine -without a drillstring-but using a pilot hole to get rid of the muck.

Jan 1, 1982

By Richard P. Rothwell

Fires in mines are so serious in their consequences and of such frequent occurrence, that their causes and the means of extinguishing them are certainly questions of the greatest interest to a large part of the engineering profession. We have already, in this country, many mines which have been burning for years, and though our hard anthracite is so difficult to ignite that for a quarter of a century after it was first discovered it mas not known how to burn it except with the aid of an artificial blast, yet most of the fires which have occurred underground have been in anthracite mines, and in the coal itself. The injury which these fires have caused to properties in various parts of the anthracite regions, and the cost of extinguishing them, would amount to many millions of dollars, and they have also occasioned the loss of many valuable lives. It is not surprising, therefore, that the subject has already attracted much attention, and the exercise of great ingenuity; and the present communication is made less with the expectation of announcing anything new, than with the object of putting upon record the present state of our knowledge on this subject, or, in other words, of indicating how defective are the present means of combating underground conflagrations. Causes of Mine Fires.—Even upon the surface, fire is a terrible foe to contend with, and there is probably no other which inspires such thorough and well-founded alarm. With what feelings, then, must we look upon this destructive element, when its field is in the narrow galleries of a mine, where the poisonous products of combustion, spreading in every direction, protect, in the most effectual manner, the fire itself from the attacks of extinguishers, while, if the face of attack be ventilated so as to enable then] to approach the seat of the fire, the air current simply increases the extent and violence of the conflagration. Fires underground originate in as various ways as those on the surface, and it is scarcely necessary to say that, except in the rare cases where they are the result of design, they are invariably classed as " accidents," and most generally as " unavoidable accidents." In reality, by an intelligent understanding of their causes and with due precautions, they can almost always be prevented. Ignorance and

By Arne F. Westgren

X-ray analysis and single-crystal study have been utilized in recent years as a new means of following constitutional changes in alloys. If such transformations can be suppressed by rapid cooling, they can be followed at room temperature in a particularly convenient manner. In the following we shall consider changes in solubility and polymorphic transformations with particular reference to phenomena of the age-hardening type. Finally a thermodynamic viewpoint is developed for examining such transformations. Changes in Solubility 1. Determinations of solubility limits in the solid state which show decreasing solubility with falling temperature are made as follows: A series of alloys extending into the heterogeneous region is prepared and quenched fromas high a temperature as possible, whereupon their lattice parameters are determined. Then one or more alloys are quenched from temperatures at which they are heterogeneous and their lattice parameters likwwise determined. For the purpose of determining the parameter the apparatus shown in Fig. 1 has been very useful for it produces sharp films in a short time which can be accurately read. High-order reflections (interferences) from the object are recorded on a film which is placed exactly perpendicular to the X-ray beam. The specimen usually has the shape of a small round bar.l Fig. 2 shows a selection of such exposures of silver-rich Cu-Ag alloys, and Fig. 3 gives the measurements made from these films. Fig. 4 gives the solubility curve which results.2 This curve is shifted to lower concentrations than the curve that is obtained from metallographic or physical methods. The X-ray method unquestionably gives more reliable data

Jan 1, 1931

By D. Harker, M. J. Murphy

The mechanism by which age-hardening takes .place is still not completely understood. The principal theories range from the extreme of "precipitaiion-hardening" to that of "order-hardening," with many intermediate gradations. In the hope of obtaining new data on which to base a choice among the many theories, the authors have made electron micrographs of formvar replicas taken from metallic specimens at various stages of age-hardening. The results so obtained on an alloy of 2 per cent beryllium in copper and one of 20 per cent molybdenum in iron will be described in the following pages, as well as the technique used in preparing the replicas. Preparation of Formvae. Replicas of Metallic Specimens This section is concerned with the techniques that have roved successful in preparing formvar replicas for studying the microstructure of metals with the electron microscope. Because of its simplicity and accuracy, the formvar replica1 method developed in the General Electric Research Laboratory has been used exclusively, since it is much simpler than the silica replica method of Heidenreich and Peck2 and produces as good results. The formvar method to be described requires a technique acquired only by practice, and no foolproof set of rules can be given. it is a rapid method and a replica can be obtained in less than five minutes under favorable conditions. This does not mean that perfect replicas can be produced every five minutes, but rather that one can well afford to take several strippings* in order to produce a replica of high quality. The metallographic technique required for replica work—very fine polishing and etching with very dilute solutions—is described here. It can be said, in general, that almost any surface that has been carefully prepared for a photomicrograph at 1000 or more diameters can be used to obtain a replica for the electron microscope. Preparation of Metallographic Specimens The preparation of the metallographic specimens is somewhat more exacting than that usually given to samples to be used for inspection under the light microscope. After much experimentation, it was concluded that the best method consists in polishing the metal through to the coarse cloth, then etching and repolishing on final cloth until the layer of distorted metal is removed. After this procedure has been completed, a dilute etch—to approximately the depth necessary for a micrograph at 1000 diameters—usually produces a sur-

Jan 1, 1945

SPEAKING generally, it may be said that leaching is the simplest method of recovering copper from its ores. Likewise it is perhaps the oldest method of treatment used by copper metallurgists of the modern era. Reliable records indicate that as early as 1752 cupriferous pyrite was leached in the famous Rio Tinto region in Spain. Though the manipulation was quite different from that in use today at Chuquicamata, New Cornelia, Inspiration, and Andes, it resembled that employed by Phelps Dodge at Bisbee, as described in Chapter XIV. Leaching consists of subjecting ore to the action of a liquid solvent or menstruum (usually an aqueous solution) which dissolves the major part of the soluble copper minerals. The resulting pregnant solution is drained off or otherwise separated from the residual ore; and the copper in the solution is then recovered by some appropriate means of precipitation. When sulphuric acid is the lixiviant, as is usual, the simplest procedure is to pass the copper-bearing solution through large troughs containing scrap iron. The iron displaces the copper in the solution, precipitating it as a slime coating the iron and varying in color -from bright copper to a dull black. This may be washed off at intervals, collected as a sludge, dried, and melted with a little fluxing material to produce reasonably pure copper. Usually, of course, the mud is sent to a smelter where most often its destination is the converter or reverberatory furnace. Modern practice uses precipitation on iron only as a complemental process to electrolytic precipitation or deposition, wherein the pregnant copper-bearing solution, acting as the electrolyte in a cell having insoluble anodes and copper cathodes, is depleted of the copper it contains. Cathode copper, 99.5 per cent pure, is produced ready for the market as refined copper, or for a simple process of melting, fire-refining, and casting in

Jan 1, 1933

By H. H. Hausner, H. S. Kalish

IN recent years zirconium and beryllium have become of great interest because of their special properties. Zirconium is known for its remarkable ability to absorb the gases oxygen, nitrogen and hydrogen, has extensive use as a getter in electron tubes and has indeed become the primary metal in the manufacture of photoflash bulbs. Beryllium is of interest because it is light metal and as such could supplement aluminum and magnesium in light metal applications. The late development of zirconium ductile at room temperature produced by both the iodide and calcium reduction methods has stimulated frequent articles on this metal in the recent literature. Beryllium is so closely akin to zirconium crystall-ographically that some investigators are of the opinion that beryllium should be ductile at room temperature if it were pure enough. The crystallographic relationship of beryllium and zirconium, the interest created in Be-Zr alloys where the zirconium is believed to function as a remover of solid solution gas in beryllium and thus increase the ductility of the beryllium rich alloy, and the amenability of these metals to powder metallurgy methods stimulated this approach to an investigation of the system Be-Zr. Preliminary work showed that a zirconium compact melted when pressed in contact with a beryllium compact and sintered at 1250°C, without any apparent final bond between the two. A search of the literature revealed nothing pertinent about the Zr-Be system or about any zirconium - beryllium alloys. In 1936 Misch³ vaguely identified the compound ZrBe2 and reported that it has a deformed cubic structure. Two patents," , were issued to Mach-lett Laboratories in 1943 and in 1946 regarding the addition of small amounts of zirconium to beryllium in order to improve the ductility of beryllium so that it may better be used for X ray windows. In considering the alloy formation of beryllium with other metals Raynor thought it unlikely that zirconium would have any solid solubility in beryllium. From this indefinite information nothing could be ascertained about the possible use of Zr-Be alloys or the use of these metals intimately. A brief preliminary study of the system Zr-Be by powder metallurgy methods was undertaken to provide regions for more intense studies of Zr-Be alloys and as a guide to a formal phase diagram determination. The investigation described in the following pages was completed in less than three weeks. The usefulness of this rapid method to facilitate phase diagram studies and new alloy investigations will be shown. Materials and Procedure Zirconium powder was produced from crystal bar stock of high purity supplied by Foote Mineral Co. The crystal bar was converted to hydride at 730°C, crushed, and the hydride decomposed in purified argon at 850°C. 60 pct of the powder passed through a 325 mesh screen, 40 pct of the powder was —140 mesh, +325 mesh and the average particle size of the total was 8 to 12 microns. The beryllium powder was used as re-

Jan 1, 1951

By Harry L. Washburn, Robert L. Llewellyn, W. J. Halvorsen

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment. JUSTIFICATION FOR COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-range planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and nuclear energy. Coal prices for power plants are still on a Btu (British thermal unit)

Jan 1, 1981

R. B. BRINSMADE, Ixmiquilpan, Hgo, Mexico* (written discussion). As the discussion of Mr. Graton's paper by Messrs. Norris, Patterson, and Crane has been from the standpoint of the mineral land-value owners, a few remarks in the interest of the "under dog"-the average taxpayer and citizen-may prove timely. In my discussion of Doctor Raymond's Paper1 and of the papers of Messrs. Gibson2 and Godson, 3 have endeavored to demonstrate, from both political economy and history, that our existing system of unrestricted private ownership of land is incompatible with equality of economic opportunity and, therefore, subversive of our democratic political institutions. In Mr. Graton's paper, the same land problem is important, though camouflaged by the failure of the Federal income tax laws to distinguish between land and capital, in the requirements for valuation, or between earned and unearned incomes in the levying of taxes. I disagree with Mr. Graton's statement, on p. 2967, as follows: The immense majority of mining ventures are failures. A multitude of disappointments is relieved by occasional success. Were it not for the chance of great rewards, all the vitally necessary but mainly unremunerative work of exploration would not be undertaken. In contrast with nearly all other fields of endeavor, it is altogether unlikely that, on the whole, the gains in the successful mining ventures suffice to offset the losses in the unsuccessful.

Jan 3, 1920