Search Documents

By M. Z. Rashad, H. A. El-Sageer

This paper compares the covariance and multiquadric functions in some mining and geological applications. The basic principals of the two techniques are covered briefly. Similarities and dissimilarities of the covariance and multiquadric functions are discussed geometrically, mathematically and practically. A 14 km2 x 16 km2 area in Baharia Oasis, Western Desert of Egypt, was selected for a detailed comparative test. The gravity anomalies of 48 test stations were computed by using the data of 63 control stations. The results indicated that the covariance function is quite better than the multiquadric one. On the other hand, the multiquadric function is simpler in computation than the covariance, which requires precalculations such as semivariogram and covariogram. Moreover, multiquadric equations are based on geometric and physical considerations rather than covariance functions.

Jan 1, 1992

By Fathi Habashi

THE MOST important arsenic minerals are shown in Table 6-1. The recovery of arsenic from arsenic sulfides is treated in Chapter Four. Arsenical ores may be either leached directly, or first smelted to volatilize as much arsenic and sulfur as possible, and the resulting product, called speiss, is then leached. A speiss is mainly a complex mixture of metal arsenides, but its [Table 6-1. Arsenic minerals. Arsenides Niccolite NiS Smaltite CoAs2 Skutterudite CoAs3 Sulfarsenides Cobaltite CoAsS Enargite CuaAsS4 Arsenopyrite FeAsS Arsenic sulfides Realgar As4S4 Orpiment As2S3] composition varies widely, depending on the type of ore treated. A speiss usually contains 15-35% arsenic. Methods of leaching are describedd in the following paragraphs.

Jan 1, 1970

By K. N. Han

The dissolution kinetics of cobalt in iodine/ iodide solutions were investigated using a rotating-disc technique. Variables studied included temperature, rotating speed, concentration of lixiviants and the pH of the solution. The overall dissolution reaction appeared to be limited by the mass transfer of tri-iodide through the diffusion boundary layer with an Arrhenius activation energy of <16.2 kJ/mol (4 kcal/mol) over the temperature range of 2 to 42ºC. The pH of the solution had little effect, as long as the pH of the solution was <8. However, when the pH of the solution became >8, the dissolution rate decreased dramatically, due to passivation. The rate of dissolution was in good agreement with the dissolution model developed by the authors earlier.

Jan 1, 1995

By Edgel P. Stambaugh

Oxides are important for use in the production of metals, ceramic hardware, paints, permanent magnets, magnetic recording tapes and many other uses. In some of these applications, particle morphology, degree of crystallinity, purity, and homogeneity are relatively insignificant, while for other uses, these same properties are of critical importance. Many conventional processes are based upon recovery of the oxides from aqueous solutions by processes which include neutralization, evaporation of solvent, and precipitation of a complex salt. Consequently, many of these techniques lead to oxides of low quality. There is a growing demand for oxides of high quality, i.e., materials with narrow particle size distribution, controlled particle morphology, high purity, few structural defects, and high degree of crystallinity and homogeneity. This demand has prompted industry to search for new approaches for the manufacture of these special materials. One new approach for preparing high quality oxides is hydrothermal precipitation. This process has been used for preparing simple oxides such as ZrO2; mixed oxides such as ZrO2-SiO2; and complex oxides such as BaTiO3. These oxides were prepared in a high state of purity with a high degree of crystallinity and., in many cases, without the addition of precipitants. Many impurities- that are normally precipitated by conventional methods such as neutralization present no problem since they remain in solution. Nature of the process and its applications are discussed in this article.

Jan 1, 1977

By Clayton Williams, Dale M. Hata, Glenn M. Boyce

The Upper Llagas Creek Flood Protection Project in Northern California encompasses portions of the communities of Morgan Hill and Gilroy, and unincorporated areas of Santa Clara County. The project provides for flood protection improvements along Llagas Creek and two of its tributaries, West Little Llagas Creek and East Little Llagas Creek. Llagas Creek is one of the tributaries of the Pajaro River and drains a watershed of approximately 104 square miles. The river system has a history of flooding the watershed communities, and the project’s goal is to provide 100-year flood protection by creating a bypass infrastructure, including channels, cut-and-cover culverts, and a tunnel. The project has been divided into several phases. This paper describes Phase 2A, which consists of approximately 2,150 linear feet of lined horseshoe-shaped bypass tunnel measuring 14 feet wide by 12 feet high. The bypass tunnel was sequentially excavated using a combination of roadheader and controlled blasting through colluvium and weathered to fresh greenstone. The tunnel was mined near residences, requiring strict noise and vibration controls. Phase 2A also includes the construction of twin bypass concrete culverts, portal shoring, and dewatering systems. It features the use of a Design Review Board and partnering for project delivery. This case study discusses the bypass tunnel design, progress of tunnel construction, plans to complete the work, construction risks, and the software and procedural tools being used to manage the project, including ProjectWise construction management software.

Jun 13, 2023

By R. Woods, J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher.

Jan 1, 1976

By G. Deschenes, M. Fulton

The New Britannia Mine processes a qumtz-carbonate gold ore containing 4.63 git Au at a rate of 2,200 tpd. The ore contains approximately 3 .0% arsenopyrite, 2. 7% pyrite and the rest is gangue minerals. Eight to ten percent of the gold is refractory to leaching. Two years ago, New Britannia Mine experienced cyanidation problems. Gold extraction was not stable and occasionally decreased significantly. Preliminary test work, at laboratory scale and in the plant, indicated that lead nitrate addition was beneficial. A laboratory study was initiated to evaluate the level of control of the parmneters (grinding size, dissolved oxygen, pH, free cyanide and lead nitrate) to optimize the efficiency of the process. It was found that lead nitrate addition is required to alleviate the effect of metallic sulphides. This addition causes a significant increase in the gold leaching kinetics and a reduction in the cyanide consumption. The optimum system appeared to be: leaching for 24-30 hours at pH 11.8, 50 git lead nitrate, 250 ppm NaCN and 8 ppm 02. The gold extraction was 89.8% with grinding at 89%-74Fm (leached tail at 0.48 git). Cyanide and lime consumption are 0.40 kglt NaCN and 1.9 kglt respectively. Following the incorporation of lead nitrate, overall gold extraction was increased from 89.2% to 91.1 % but no change was noticed in cyanide consumption. The gross profit is $CDN 988,000 per year.

Jan 1, 1999

By Paul L. Boni

Trona, Na3(CO3)(HCO3) ? 2H20, is mined in quantity from saline facies of the Eocene Green River Formation of southwestern Wyoming. The Green River deposits are the world&apos;s largest known resource of natural sodium carbonates. An estimated 127 billion tons of trona ore are known to occur in beds exceeding 4 ft in thickness (Wiig and others, 1995). Twenty-five trona beds, exceeding 3 ft in thickness, and covering at least 100 mil have been identified. The beds are numbered sequentially in ascending stratigraphic order. Trona beds underlie more than 850 mil (bed 17) and are up to 37 ft thick (bed 1) (Culbertson, 1966). Five underground mines, operating in beds 17, 19, 20, 24, and 25, process trona to produce soda ash (sodium carbonate). A total of 11,837,703 short tons of soda ash were produced from 17.1 million tons of trona ore in 1997 (Kostick and Clark, 1998). A detailed study of trona bed 17, using techniques of petrography and X-ray diffraction, has been undertaken in the Solvay trona mine, near Green River, Wyoming. A continuous, vertical-channel sample was taken from near the production shaft for this study. At this location, bed 17 is 12.6 ft thick and includes several stratigraphic markers that are easily correlated throughout the mine and in surrounding drill cores. Bed 17 in this area averages 90% trona through its entire thickness (Wiig and others, 1995) and 95-100% trona in the lower two-thirds of the bed. Mineral impurities include water-insoluble dolomite, quartz, pyrite, clays, and other minerals and partially water-soluble northupite and shortite. Northupite, Na3Mg(CO3)2C1, contributes to chloride contamination in the soda-ash product and is concentrated in the upper one-third of bed 17, which is left behind as roof rock. Northupite has two modes of occurrence: (1) as bedded strata with dolomite, chert, clay, and shortite and (2) between primary trona crystals in trona spar. Petrographic and mineralogic data indicate that this section of bed 17 was deposited subaqueously during its early and late history and may have undergone periods of deposition in a subaerial or marshy environment. Stratigraphic data indicate that trona accumulated at an annual rate of 2-4 in. per year. During trona deposition, dolomite, CaMg(C03)2, precipitated in parting layers when new water entered the lake, freshening supplies of calcium and magnesium. The lack of clay minerals in the trona facies suggests water input may be by means of springs, as opposed to overland flow. Clay occurrences in thicker dolomitic partings within the trona facies indicate periods of episodic overland flow, possibly resulting from storms in the surrounding basin.

Jan 1, 1999

By F. Freme

Coal production in the United States in 2008 reached a record level of 1.06 Gt (1,171.5 million st), according to preliminary data from the U.S. Energy Information Administration (EIA) (Table 1). This is an increase of 2.2 percent, or 22.5 Mt (24.8 million st) above the 2007 level and 7.9 Mt (8.7 million st) above the prior record level set in 2006. Although coal production was higher in 2008, U.S. total coal consumption decreased in all sectors for the year. Coal consumption in the electric power sector in 2008 was lower by 0.3 percent, while coking coal consumption decreased by 2.8 percent and the other industrial sector declined by 3.7 percent. The commercial and institutional sector, that had been called the ?residential and commercial? sector prior to 2008, declined by 0.6 percent in 2008. It is the smallest of all the coal-consuming sectors. (Note: All percent-age change calculations are done at the short-tons level.) U.S. coal exports were significantly higher in 2008, while coal imports decreased during the year. Total coal stocks increased in 2008, as some consumers added to their stockpiles. The coal synfuel industry, which grew throughout most of this decade, disappeared from the scene due to the expiration of the available federal tax credits at the end of 2007. The decline in coal consumption during the year was the consequence of slowing domestic economic growth, particularly in the latter half of the year, combined with the weather conditions in 2008, resulting in lower demand for electricity. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. decreased in 2008. Coal-based generation also decreased, resulting in a 3.2-Mt (3.5-mil-lion st) drop in coal consumed in the electric power sec-tor. Coal use in the non-electricity sector decreased by 3.3 percent to a level of 72.6 Mt (80.1 million st). The international coal markets in 2008 were the driv-

Jan 1, 2009

By Aleksandar D. Bugarski, Dylan A. Ritter

The results of laboratory characterization of tailpipe emissions for three “clean” engines that meet U.S. EPA Tier 4 final emissions standards were used to assess the viability and effectiveness of repowering existing engines and powering new mobile equipment with those engines as a control strategy for reducing exposure of underground miners to diesel aerosol and criteria gases. The evaluated engines were representative of those that achieve the emission standards through implementation of various in-cylinder emissions control strategies, use of crankcase filtration, and use of three types of exhaust aftertreatment systems: (1) diesel oxidation catalytic converter (DOC), (2) combination of DOC and the full-flow wall flow monolith diesel particulate filter (DPF), or (3) combination of DOC, diesel exhaust fluid (DEF) based selective catalytic reduction (SCR) system, and ammonia slip catalyst (ASC). The study showed that the highest reductions in concentrations of diesel aerosols in underground workings, in terms of both mass and number, could be achieved if the engines, preferably in all power classes, are fitted with viable DPF systems. The use of U.S. EPA Tier 4 final engines equipped with DOC and DOC/SCR/ASC systems could help operators to considerably reduce mass, but not number concentrations of aerosols. The emissions of two of the evaluated engines, one equipped with DOC and the other equipped with DOC/DPF systems, were characterized by substantial secondary NO2 emissions that would limit the viability of those engines for underground mining applications. It appears that the catalyst formulations used in the exhaust aftertreatment systems of the “clean” engines marketed to the underground mining industry need to be formulated to minimize the potential for generation of secondary NO2 emissions. The results indicate that the engines fitted with viable SCR/ASC systems present a low-NO2 alternative. All three “clean” engines were found to have low CO output. Therefore, due to nuances associated with the use of diesel-powered mobile equipment in underground mines, special attention needs to be paid to the selection and potentially optimization of “clean” engines for underground mining applications.

Feb 1, 2025

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By Jr. Smith

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915 In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various borate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 400 feet (121.9 m) deep, 3000 feet (914.4 m) long and 1000 feet (304.8 m) wide. The borates in the Boraxo pit consist primarily of three minerals. These are about 50% coiemanite (C2B6O11&apos; 5H2O), about 40% probertite (NaCaB5O9.5H2O), and 10% ulexite (NaCaBcO9.8H2O). The colemanite, along with boric acid and high-grade coiemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder. This provides the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content.which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations.

Jan 1, 1978

By A. E. Foscolos

British Petroleum (BP, 2005), indicates that world reserves for oil to be 1198 billion barrels, for natural gas the equivalent of 1156 billion barrels of oil and for coal the equivalent of 3219 billion barrels of oil. If we take into consideration the mean aver-age annual increase in demand of the last three years for oil, 2.6%, for natural gas, 3.9%, and for coal, 6.6%, then their respective reserves? lifespan are calculated to be 27, 34 and 38 years. Without taking into account their annual increase in demand, lifespan increases to 38, 67 and 161 years respectively. Since zero increase or perpetual increase in energy demands on finite resources is unrealistic the selection of the most suitable energy commodity for power generation rests upon the law of supply and demand of each commodity. This defines its price hence its selection for the production of cheap electricity. When the ratio of supply to demand is less than one, peak production is achieved. Any further increase in demand results in price increase to quench its demand. The Association for Oil and Gas Peak (ASPO) has calculated that when oil demand exceeds 84 million barrels/day, Peak Oil Production will be attained thus prices will start to increase in order to even demand with supply. Correspondingly, Gas Peak Production is expected to take place when demand exceeds 9.1 or 10.2 billion cubic meters/day. Peak Oil production has been calculated to take place in the current year, 2006, while Gas Peak production is estimated to take place between 2020 and 2025 provided that gas will not cover the energy deficit created from the lack of oil otherwise Gas Peak production could arrive as early as 2010. The use of coal for power generation is considered a better alternative than oil and gas if new combustion technologies with an energy efficiency of 43%, Germany, and 47%, Denmark, are adopted. These not only extend the lifespan of coal reserves but reduce also CO2 emissions by 25% and 31%, respectively. In the very near future CO2 sequestration and fixation in deep geological strata will eliminate its emissions thus rendering the use of coal the cheapest feedstock for power generation.

Jan 1, 2006

By W. Choi

The present study revealed that the bioleachability of a chalcopyrite flotation concentrate is influenced by the semiconductor properties of CuFeS2. The overall reaction of biooxidation,

Jan 1, 1991

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

By T. W. Camm

"As engineers, we are trained to use logical, rational problem solving to insure our mines operate at maximum efficiency. We tend to use the same technical approach to design safety into all mining systems. This works well for machines, but not so much for the human component. Recent insights in the field of behavioral economics provide useful ideas for addressing the fact that we are driven by emotions more often than by rational thought. Understanding the nonrational aspect of human behavior is an important piece of any safety system design. INTRODUCTION The most common economic model is based on humans making rational decisions; that given the proper information, we will make a logical, rational decision based on what is best for ourselves (Ariely, 2009, p. xviii). In many cases this is an accurate description of how we make decisions. As an engineer, I was trained to apply the precision of mathematics and logic to solve problems. As an engineering professor, I now teach this approach to bright young minds preparing them for a life of professional effectiveness as practicing engineers. That said, we are not only rational. Daniel Kahneman, winner of the Nobel Prize in Economics, describes a model for how we think (Kahneman, 2011). System 1 is the part of our mind that is fast, intuitive, and emotional; while our logical, slower, and deliberative mind is System 2. According to Kahneman’s model, System 1 runs automatically, most of what you think and do originates in System 1. System 2 takes over when things get difficult, including the application of math and logic, and the resolution (or avoidance) of conflict. As engineers, we would typically assume that we operate in System 2 mode most of the time. This is where the model becomes useful, for Kahneman points out two important aspects of the dynamic between the two systems in our mind. First, System 1 has biases, systematic errors that lead to answering questions with an easier answer (rather than a right answer) before System 2 is engaged. Second, we can be blind to the obvious, and also be blind to our blindness. Complicating things further, System 1 cannot be turned off (Kahneman, pp. 24-25)."

Jan 1, 2015

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to &apos;Environmental Control Department&apos;. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and &apos;Total Environment&apos; includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By Angela K. Braden

Igneous rock exposures occupy only a minor portion of surface area (<18 mi2) in Arkansas, and are divided into two major groups: nepheline syenite (7 mi2) and syenite complexes (8 mi2), with various dikes and sills representing the remaining surface exposures. The syenite complexes have been the sites of major vanadium and minor titanium production during the past 50 years. Nepheline syenite exposures were important in the early production of locally used building stone; however, aggregate and roofing granules have now become the principal market for the production of nepheline syenite in Arkansas. Nepheline syenite intruded into a sequence of Paleozoic sedimentary rocks in Arkansas and is exposed in two areas: in Saline County near the town of Bauxite, and in Pulaski County at Granite Mountain, just southeast of Little Rock. Although the central Arkansas region had been investigated thoroughly for bauxite by the early 1950s, the nepheline syenite resources of the region have yet to be evaluated systematically by the state. Arkansas nepheline syenite was evaluated for its ceramic uses in 1952. Some recent industry interest has revolved around its potential use as a sand-blast abrasive. The largest exposed areas of nepheline syenite, located at Granite Mountain, currently are being mined by the Minnesota Mining & Manufacturing Company (3M) and McGeorge Contracting (Granite Mountain Quarry). 3M has been in operation since 1947 and mainly produces roofing granules. A fine powder produced by 3M during crushing that is marketed under the name Donnafill? recently has seen use as filler in self-compacting confined construction and as an additive (frit) in common brick. Since the early 1960s, Granite Mountain Quarries has produced a variety of aggregates, ranging from riprap to industrial sand, and recently constructed a computerized hot-mix-asphalt production facility. Approximately 4.5 million tons and 1.2 million tons of syenite were produced from Granite Mountain and 3M, respectively, during 1979. No production values are available after this date; however, combined production from both quarries is estimated to be at least 6 million tons annually.

Jan 1, 1999

By P. R. La Pointe, H. C. Ganow

The production of both over- and undersized coal fragments is a constant problem to open pit operators in the Powder River Basin. Operators strive to achieve production blasts that economically minimize the weight percentage of over- and undersize coal. However, natural fractures influence blast fragmentation, and can impose limits on the final fragment size distribution. ARCO&apos;s Anaconda Minerals Company studied the limits placed by natural fracturing as part of a wider geotechnical study of the Wyodak Coal in the eastern Powder River Basin, Campbell County, Wyoming. Measurements of fracture orientation, size and spacing were made at ARCO&apos;s Black Thunder Mine. These data were used to form statistical distributions for natural fracture size, spacing and orientation. An algorithm was created to select fracture properties at random from these distributions and to form hypothetical blocks. The blocks were then numerically "sieved" to derive pos- sible particle size distribution curves. These curves are compared to fragmentation results from samples taken from three test blasts. All test blasts yield very similar lognormal fragment size distributions. The median particle size varies from 1.25 to 2.0 in.(3.2 to 5.1 cm), the mean from 4.0 to 8.5 in. (10.2 to 21.6 cm). The standard deviation was about 1.6 in. (4.2 cm). Coal fines (fragments < 0.25 in. or 0.64 cm) are about 15%. Calculated fragment distributions for the natural fractures predict the median size well but underestimate the variance. Algorithm modifications to account for processes known to occur in the comminution zone near the blast hole significantly improve the match in the fine coal size range. The match suggests that spacing of fractures, rather than fracture length, controls the formation of fine- and medium-sized fragments. On the other hand, the oversize coal is controlled by the fracture lengths, rather than the spacing. Data from subsequent test blasts support this idea. By increasing delay times from 8 msec to 17 msec, engineers were able to reduce fines to 7% - 10% but could achieve no further improvement, despite changes in shot pattern geometry, decking and hole size. The hypothetical fragment distributions show that, even without blast enhancement, about 5% of the natural coal blocks are fine-sized.

Jan 1, 1986

Many mining operations generate seismic signals. They come from blasting and from underground mine failures such as rockbursts, longwall first caves, coal bumps and pillar collapses. Traditionally, seismic motions have been of concern on a local scale because they could create damage to structures at the mine site or at neighboring locations. Recently, there has been much interest in the Comprehensive Nu-clear-Test-Ban Treaty (CTBT). It prohibits any kind of nuclear explosion, anywhere. So distinguishing signals of mining operations from a possible nuclear explosion becomes important. An international monitoring system (IMS) is being implemented to verify the Treaty when it is ratified. It includes a large number of seismic stations capable of recording signals at regional (200 to 2,000 km or 124 to 1,240miles) and teleseismic (more than 2,000 km or 1,240 miles) distances.

Jan 1, 2000