Search Documents

By Marco A. S. Aguiar, Luis G. S. Sobral, Vânia Mori, Paulo A. Medeiros da Silva

"Copper occurs in the crust of the earth, predominantly, as sulphides. Among the copper sulphide minerals, the chalcopyrite is the most abundant and the most refractory to the conventional oxidative processes. This work aims at developing an electrolytic process for treating a copper sulphides flotation concentrate, more precisely chalcopyrite (CuFeS2) and bornite (Cu5FeS4) in the percentages of 70 and 30%, respectively.This paper presents a low-cost operational electroleaching process for treating copper sulphides flotation concentrates, with a high chalcopyrite content. This research practical work aims at improving the copper extraction from that sulphide mineral, in a relatively short time with low-operating cost taking into consideration the influence of a cationic surfactant. The electrolyte of the electrolytic reaction system was a 2,0 mol.L-1 NaCl solution containing CTAB, a cationic surfactant. The electroleaching system contains one DSATM (dimensionally stable anode) anode and two nickel or copper foams (threedimension electrodes. During the electroleaching process the chloride ions are oxidized to chlorine at the anode surface, which in contact with the aqueous phase generate enough hypochlorite ions to oxidize chalcopyrite.The copper ions released from the chemical oxidation process are reduced at the cathode surface as metallic copper."

Jan 1, 2008

By Fumiatsu Sato

In recent years, an increasing number of urban soil contamination cases have been found during redevelopment of former factory sites. Hydroclassification technique, separating heavily contaminated fine soil particles from contaminated sites, is one of the economical remediation techniques for contaminated soil by heavy metals, but the separated fine soil particles are generally landfilled because of the difficulty in removing strongly adsorbed heavy metals on them. In the previous study, the authors have investigated the mechanism and the optimum condition of chlorination-volatilization technique to eliminate heavy metals from inorganic waste and found it was needed to heat up around 1273K. In this paper, a new remediation technique for lead contaminated fine soil particles is proposed. This technique is composed of chlorination and subsequent warm water extraction. In the chlorination step, water-insoluble lead complex is chlorinated to be water-soluble lead chloride without volatilization, by heating the soils with MgCl2-CaCl2-KCl salt mixture at relatively low temperature. By subsequent warm water extraction, lead chloride is leached out. Effects of chlorination conditions, such as time, temperature, composition of the salt and added salt ratio, on lead behavior were investigated. It was proved that lead concentration could be reduced below Japanese environmental standard.

Jan 1, 2006

By Noboru Masuko, Sachiko Ono

"The structure and composition of anodic films formed on aluminum in a borate solution have been investigated by using TEM and SIMS with respect to the effect of current density and electrolyte temperature. The film is composed of a boron-containing outer layer and a boron-free inner layer with disc-like crystals present at the interface. The thickness of the film formed at constant current density up to an identical voltage, decreases with increasing current density. The thickness increases remarkably with elevated temperature. The transport number of Al3+ estimated from the thickness ratio .of the cuter to the inner layers is 0.4 when the film is formed at the current density of 20 Am-2 at 60°C. It increases slightly with increasing current density and decreases significantly with increasing temperature. Content of boron in the outer layer increases 1.5 times when current density .increases 10 times. These changes in film structure and composition with electrolysis conditions must have a significant role in the determination of electric properties of anodic alumina films as a capacitor material.IntroductionThe growth of anodic alumina film in ·a neutral electrolyte proceeds at both film/electrolyte and film/substrate interfaces giving a duplex structure. The oxide layer formed at the former interface includes electrolyte anions while a-pure alumina layer is formed at the latter interface. The thickness ratios of each layer respectively represent transport numbers of Al3+ and 0 2 - (1). The film thickness and the incorporated anion content as well as transport numbers of both ions must affect the dielectric properties of the film as a capacitor material. However, the correlation between film structure and electrolytic conditions is not fully understood (2). For the further clarification of anodic film growth mechanism, more detailed characterization of anodic films in relation to electrolytic conditions is advantageous. In the present paper, therefore, the effect of current density and electrolyte temperature on the microstructure and composition of anodic barrier films formed in a neutral borate solution was studied. The films were characterized by direct observation using transmission electron microscopy (TEM) and depth profiles of constituent elements obtained by secondary ion mass spectroscopy (SIMS)."

Jan 1, 2000

By Onuralp Yucel, Ahmet Turan, Halil Yildirim

"Nickel is mainly used in stainless steel production as ferronickel. In recent years, low grade ferronickel or nickel pig iron (NPI) is used in stainless steel production to reduce expenditure of nickel price. In this study, Turkey East Anatolian region lateritic nickel ores were directly introduced carbothermal reduction to produce NPI. Firstly the raw lateritic ore that contains 0.9% Ni, 0.054% Co and 2.3% Cr was mixed with metallurgical grade coal at different stiochometric ratios. The samples were smelted at 1600-1650 °C temperature range in an induction furnace for 25 min. In the second experimental set, different processes times were carried out from 15 to 35 min. The raw material, obtained alloys and slags were analyzed by using XRD (X-Ray Diffractometer), XRF (X-Ray Fluorescence Spectrometer), AAS (Atomic Absorption Spectrometer) and EPMA (Electron Probe Micro Analyzer) techniques.IntroductionNickel is an important element that has many application areas in the industry and there are a lot of kinds of nickel products such as refined metal, powder, sponge etc. 65% of metallic nickel is used in stainless steel, 12% is consumed as superalloy and non ferrous alloy because of its superior corrosion and high temperature properties [1].Nickel is a transition metal that is mined from mainly two types of ore deposits as sulphide ores and lateritic ores. Although 73% of nickel ores are laterites, 55% of primary production is from sulphide ores [1, 2]. The importance of lateritic ores is increasing due to the increase in nickel prices and decrease in reserves of sulphide ores.There are pyrometallurgical, hydrometallurgical and combined (pyro-hydrometallurgical) methods which are used for the extraction of nickel from lateritic ores. HPAL (High temperature pressure acid leaching) is generally used to recover nickel and cobalt from laterite nickel ores. It is suitable for the plants processing ores with low magnesium oxide and aluminum oxide content. Lateritic ores are exposed to hot acidic leaching around ~250 °C to dissolve cobalt and nickel under high pressure. The main disadvantage for HPAL is the high cost of titanium autoclaves. Process is complex and difficult to control due to the high pressure and heating of the process [2, 3 and 4]."

Jan 1, 2012

By Dmitri Goljandin, Jaan Kers, Xiangjun Zuo, Lifeng Zhang, Priidu Peetsalu

"In this paper, the mechanical milling of the electronic wastes was carried out. The metal parts and plastic parts were roughly separated. The final plastic powder size could be as small as ~100 µm. Then the pyrometallurgical recycling Printed Circuit Boards (PCB) was executed. The mechanisms of thermal degradation and combustion are investigated using TG/DTA and MS. Some chemical powders, such as Na2CO3, NaHCO3, NaOH and CaCO3 are used to control the exhausted toxic gas such as Br2. Introduction Waste electric and electronic equipment (WEEE), or electronic wastes (E-wastes), has been taken into consideration not only by the government but also by the public due to their hazardous material components [1-3]. From the point of material composition, electronic wastes can be defined as a mixture of various metals, particularly copper, aluminum, and steel, attached to, covered with, or mixed with various types of plastics and ceramics [4]. Precious metals have a wide application in the manufacture of electronic appliances, serving as contact materials due to their high chemical stability and their good conducting properties. Platinum group metals are used among other things in switching contacts (relays, switches) or as sensors to ascertain the electrical measurand as a function of the temperature [5]. Table 1 [6] gives examples of the metal composition of different electronic scraps from literatures. Additionally, non-ferrous metals and precious metals content have gradually decreased in concentration in scraps. The value distributions for different electronic scrap samples are shown in Table 2 [6], where the metal price data are from London Metal Exchange (LME) (Octoebr 2007). It can be seen that for cell phones, calculators, and printed circuit board scraps, the precious metals make up more than 70% of the value, for TV boards and the DVD player they still contribute to about 40%. This indicates that the major economic driver for recycling of electronic waste in industry is from the recovery of precious metals. Behind the precious metals come copper and zinc, while Al, Pb, and Fe are less value. Recycling of electronic waste is an important subject not only from the point of waste treatment but also from the recovery aspect of valuable materials."

Jan 1, 2008

By M. Fafard, R. Ahmed, O. Dion-Martin

"The optimization of aluminum sheet and tube forming needs the use of large strain finite elements software. The precision of the predicted results from those simulations depends mainly on the quality of constitutive law of the material used. In order to improve quality of these simulations, Barlat has suggested a new yield function named YLD2000-2d. This criterion describes the anisotropic behavior of the rolled aluminum plates. This work consists of characterizing the AA5754 alloy and estimating the material parameters needed for the YLD2000-2d criterion in LS-DYNA. In order to get these parameters, various mechanical testing were performed such as bulge and tensile tests. Moreover, the bulge test was also used to obtain an estimation of work hardening curve in large strain condition, up to 50%. The objective of this paper is to share the experimental results of the characterization of AA5754 aluminum alloy.IntroductionResearchers from National Research Council Canada's Aluminium Technology Center (NRCATC) and Aluminium Research Centre - REGAL, are working on aluminium tube hydroforming processes of AA-5754-0 alloy, used in automotive industries. Hydroforming process presents several difficulties such as wall thinning and section changes. In order to control them, some parameters can be set during the process like pressure rate and end feed level [1]. Given the complexity of the parts and the variability of the control parameters, the use of finite element method (FEA), like LS-DYNA, based on large strain theory is thus necessary. The accuracy of predicted results depends mainly on the quality of the constitutive law used to model the behavior of material. FEA results seem to be valid with the von Mises yield criterion used in some cases. But, given the anisotropic properties of the AA-5754 alloy, a more appropriate criterion could be used. The *MAT_ BARLAT YLD2000 shell material criterion, developed by Barlat [2], who's taking into account the anisotropic behaviour, was chosen due to its large flexibility and its good adaptation to particular elastoplastic behavior of aluminum. However, the use of this criterion needs to determine some material parameters by experimental way."

Jan 1, 2013

By Thomas F. Hagelien, Stein Tore Johansen, Svend Graadahl

"The dross appearing at the surface of an aluminium melt consists, in addition to aluminium, of mainly oxide films but also other non metallic inclusions. The inclusion particles are often poorly wetted by the metal and accumulate at the metal surface. However, in impeller stirred reactors for melt refining stirring may be exceedingly strong and inclusions accumulated at the metal surface may be entrained into the bulk metal. Concerning inclusion removal, such effects may deteriorate the effectiveness of melt refining.In this paper we investigate the surface entrainment of buoyant particles in a water model of an impeller stirred refining reactor. Under varying operating conditions the particle concentration in the bulk liquid is measured by laser light attenuation. The observed entrainment of particles is explained theoretically and metallurgical consequences of the findings are discussed.IntroductionIn the modern cast house continuos metal refining and casting is well established. One of the most distinct advances in metal refining has been the introduction of degassers which introduce bubbles into the metal. The bubbles act to remove dissolved elements together with nonmetallic inclusions. In the most efficient degassers stirring by different kind of rotors is applied to increase mass transfer and inclusion removal. However, it has been known from experience in the cast house that for violent stirring the concentration of some types of inclusions may increase from inlet to outlet of the reactor. This phenomenon has so far been attributed to production of dross in the reactor due to oxidation of metal. Due to removal of inclusions by bubbles the dross layer inside the reactor must be expected to increase in thickness by time. The removed inclusions and produced oxides due to strong stirring is removed at regular interval by the operators of the degasser. However, a fundamental understanding of the phenomena which take place in and below the dross layer is lacking. In the present work we add buoyant particles to the surface of a refining reactor and investigate how these particles may be entrained and dispersed into the liquid depending on the flow conditions. Similar investigations for gas stirred ladles have been performed by Taniguchi et al [1] who found that below a critical gas flow rate all particles are trapped at the surface. Above the critical gas flowrate the surface velocity are sufficiently high to entrain the particles. In this situation it looks like all particles are ready for the melt and a balance between terminal velocity and turbulent dispersion determine the concentration in the liquid."

Jan 1, 1999

By Jingbo Liu, Zhimin Wang, Wenchao Li

"IntroductionThe advantages of non-stoichiometric perovskite material are highlighted in many papers[l]and many of this family of materials are well-suited to integration into microsensor devices. Among them, barium titanate is the most promising due to it's piezoelectric, pyroelectric, dielectric properties. Through modification, BaTiO3-based materials can be utilized in many kinds fields, such as surface wave probe; pholoconducting devices, field-effect transistor, permanent memory permanent storage, and ultrasonic transducerl2-3l. In this Paper, a series of BaTiO3-based polycrystals were synthesized by sol-gel processing which appears to be a very promising method for the manufacture of ceramic, because it offers significant advantages such as high purity, chemical homogeneity, controlled particle sizes of ceramics, and lower processing temperatures [4]. In a sol-gel process, alkoxides of the constituent elements show different reactivity toward water so that the preparation of multi-component homogenous system is difficult. In the experiment, inorganic salt was substituted for some of the alkoxides. Acetic acid which is employed for the solvent and catalyst, acts as donor ligand to titanium alkoxide and controls, the hydrolysis polycondensation reaction. Taking these aspects into consideration, we select the system Ba(OAc)2, , La(OAc)3, Ti(O11Bu)4 and acetic acid which is used as both solvent and homogeneous catalyst for the first time.ExperimentalA series of La3+-doped BaTiO3-based nano-crystals were prepared with sol-gel technology using various parameters. The precursor solution was prepared in the presence of barium acetate, lathanium acetate, and titanium tetrabutoxide monomer in butyl alcohol. According to the flow chart (fig. I.), Ba(OAc)2, La(OAch dissolved in the glacial acetic acid (0. lmol/40ml) in a three-neck flask were mixed with a solution of titanium tetrabutoxide monomer in butyl-alcohol(l 7ml/20ml) at room temperature and under constantly, vigorous stirring conditions. In most cases, the resultant solution was golden yellow and stable in the air. To this precursor solution, containing Ba, La, Ti in the desired ratio, water was added incrementally for hydrolysis under continuous stirring until sol was formed. After aging for more than 2 hours, sol was transformed to gel at room temperature. If heated during aging, the gel was formed in a shorter time. The wet gel was allowed to dry at 50°C for more than 10 hours. The dried gel was transparent or light yellow. In order to obtain BaTiO3-based nano-crystals, the amorphous dry gel was calcined at 600°C, 700°C, 800°C, 900°C, 1000°C respectively[5]. The ceramic humidity sensor was formed through the cold-pressed, aged, capsulated routes. The dried gels were crushed in an agate mortar and then pressed into discs of ? 1.5 X l.5mm (l.5mm diameter and l.5mm thickness), then held at about 16.5 MPa pressure for 3 min [6]. The disc was sintered at 1350°C and 1400°C for I hour respectively. During the processing, an Ag-Pt electrode was inserted in the sensor [7]. (See the flow chart.)"

Jan 1, 2000

By Carl C. Nesbitt

A study was conducted to examine the treatment of metal-bearing effluents by precipitating the metals as sulfides and simultaneously collecting the particles by flotation. The precipitant was hydrogen sulfide gas which was introduced into a bench-scale column cell with air. The study included experiments of various flotation reagents and column configurations in treating solutions containing dissolved copper, lead, mercury, iron, zinc and cadmium. An acidic laboratory waste from a local copper operation was used to test the column with a solution containing several metals and arsenic. Precipitates were observed to form at the gas/liquid interface when the gas mixtures were rich in H2S. Copper, mercury, lead, and cadmium were precipitated from solution as sulfides to concentrations near detection limits. The flotation of these precipitates was enhanced with small amounts of S-7151 promoter from American Cyanamide Company and Dowfroth 1263 mixed with the feed. The recovery of the precipitates in this manner produced a smaller volume slurry which was easier to dewatering than a slurry produced by conventional precipitation techniques. The low pH and high oxidation-reduction potential in the cell from H2S addition was not conducive to form precipitates of iron, zinc or arsenic. However, these ions were precipitated as sulfides by raising the pH of the column discharge.

Jan 1, 1994

By Andre L. De Vegt

For the past eight years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps: 1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (HzS). The HzS reacts with the dissolved metals to form insoluble metal sulfide precipitates. 2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m3/d. A test program, utilizing a large scale pilot plant, will commence in November 1995 at a copper mine in the U.S.A. to remediate groundwater contaminated with sulfate and heavy metals. Biological reactor performance and selective metal recovery will be studied. Sulfur dioxide (S00 can be removed from fluegas using a combination of scrubber technology and the two biological steps. The end product is elemental sulfur. A commercial size biological desulfurization plant has been in operation since July 1994 treating 50,000 Nm3/h of fluegas. Sulfide can be removed from mining waters or anaerobic wetlands using a THIOPAQ® Sulfide Oxidizing reactor.

Jan 1, 1996

By W. G. Davenport

Inco flash smelting blows industrial oxygen, dried Cu"Fe-S concentrate, Si02 flux and recycle materials horizontally into a hot (-1500 K) furnace. Once in the furnace, the oxygen reacts with the concentrate by Reactions 1.1, 1.2 and 1.3 to give: (a) liquid matte, 55 to 60 mass%Cu (b) liquid slag, 1 to 2 mass% Cu (c) off gas, 60 to 75 volume % S02. The matte is tapped into ladles and sent to converting, Fig. 1.3. The slag is tapped into ladles, and sent to a stockpile; with or without a Cu-from-slagremoval step. The off gas is water-quenched, cleaned of dust and sent to a sulfudc acid plant. The [nco flash furnace is also used to recover Cu from molten recycle converter slag. The slag is poured' into the furnace via a steel chute and water-cooled door, Fig. 3.1. In 2000 there are five Inco flash furnaces in operation: at Almalyk, Uzbekistan (Ushakov, et at. 1975); Hayden, Arizona (Marczeski and Aldrich 1986); Hudey. New Mexico (Belew and Partelpoeg, 1993); and Sudbury, Ontario (two furnaces, Carr etal, 1997, Humphris et ai, 1997; Molino et ai, 1997). The Almalyk, Hayden and Hurley furnaces smelt Cu-Fe-S concentrates. The Sudbury furnaces smelt Ni-Cu-Co~Fe-S concentrates'to produce -45% Ni+Cu+Co matte and -1% Ni+Cu+Co slag.

Jan 1, 2001

By M. A. Barakat

Large amounts of zinc ash and flue dust containing more than 80 % zinc are accumulated during galvanization processes at the surface of molten zinc bath and in the chimney respectively. Pyrometallurgical recovery of zinc from both of the ash and dust samples has been carried out. The ash was sieved with the help of an industrial sieve shaker provided with mesh sieve having a pore size 0.9 mm. The oversize fraction cut (+ 0.9 mm) was melted at 550 °C under ambient conditions. The produced ingot (1) was analyzed whereas the coarse fraction of the produced slag (+ 0.9 mm) was treated as the coarse ash or added to it. The dust was enriched with suitable fluxing salt prior to heat treatment at 600 °C for 1 h. The produced ingot (2) was analyzed whereas the resulting slag was mixed with the fines of the ash and treated by hydrometallurgical processing to prepare valuable salts of zinc. Parameters affecting recovery processes such as time, temperature and flux percentage were studied. Results obtained revealed that the two prepared ingots (1&2) were successfully recovered with recovery efficiency amounts to =85 %. The obtained samples meet the standard specifications with relatively low price. Also in the light of the strict environmental regulations of pollution control, reuse of these wastes materials will help in keeping the environment clean.

Jan 1, 2000

By Tamas Kekesi

Anion exchange in HCl media is considered an efficient alternative to the combination of the conventional purification methods. Anion-exchange distribution functions have been determined for cobalt and the main impurity elements by the technique of batch equilibration. Results were confirmed by spectrophotometric investigations and elution tests. Based on the new and the available distribution functions, combined with the assessment of thermodynamic stability, a procedure of anion exchange separation has been devised to eliminate virtually all the impurities from the cobalt-chloride solution. Separation of copper has been enhanced by the introduction of a preliminary step under reduced conditions. The rest of the impurities are eliminated in a second anion-exchange step applying rinsing and elution stages under oxidized conditions. The optimum parameters of the procedure have been determined according to performance characteristics (purification ratios, yields and volume efficiencies) derived from the analysis of elution curves obtained with laboratory scale ion-exchange columns. Special computer programs have been developed to facilitate thermodynamic simulation, analytical correction and data processing.

Jan 1, 2003

By Lionel Ryan

In 1996, the Dominican Republic operation of Falconbridge (Falcondo) developed a 5-year Process Control Plan in conjunction with the corporate Process Control group located in Sudbury, Ontario, Canada. This plan was further refined into an analysis of the areas of the highest potential economic return for the company with the reduction shaft furnace operation being the most promising. Historically, the reduction plant, which comprises 12 shaft furnaces, has been the bottleneck of ferronickel production. Since 1996 there has been a history of control development, and the current status is that all 12 furnaces are using advanced model-based multi- variable predictive control. The combination of advanced process control (APC), improved control system performance and improved process information management has resulted in an increased throughput of 6% per shaft furnace and a reduction in operating costs of 4.5 US cent/lb of Ni. This paper reviews some of the major milestones that have been achieved in this development Keywords: Advanced Process Control; Model Based Predictive Control; Connoisseur, Reduction Shatt Furnace; Nickel Laterite Ore; Ferronickel; MonitorMV

Jan 1, 2004

By Elli Miettinen, Markku Lahtinen, Ilkka Kojo

"The recent trends of decreasing energy consumption and environmental emissions and utilization of economies of scale are strong drivers favoring continuous copper converting processes. Flash Converting benefits from low off-gas volumes and low investment and operational costs for off-gas treatment. Separate matte and blister furnaces allow the adaptation to concentrate quality changes and flexibility in layout and maintenance.The stationary blister copper bath in Flash Converting furnace is less aggressive to the furnace linings than agitated processes, resulting in low refractory consumption, long campaign life and high on-line availability.Copper Flash Converting has been successfully applied in Kennecott with a campaign life now exceeding five years. A second FCF was started at Xiangguang Copper in China in 2007. The process itself is proven, as its features are similar to those in FSF, Direct-to-Blister and Direct Outotec Nickel Flash Smelting (DON), with one significant difference: it is the easiest of all to operate.The paper presents differences between continuous Flash Converting and conventional converting based on recent experiences and studies."

Jan 1, 2009

By John J. Friel

Digital imaging systems are particularly useful in microscopy, because they make it possible to extract information not readily accessible by manual methods and to display that information clearly. Computer-aided imaging systems analyze, process and compare images, and of these, image analysis is most useful in materials science. Image analysis quantifies the microstructure by making measurements on the entire field or by measuring the size and shape of features individually. Even true surface area can be calculated. Modem image analyzers make thousands of measurements in seconds, leaving the investigator to interpret the data and relate them to process and material properties. Image processing, which may be necessary to prepare an image for analysis, includes everything from simple contrast transforms and kernel filters to complicated processes such as grain boundary reconstruction using artificial intelligence. An example of image comparison is point-by-point screening of X-ray maps of different elements to extract phases. In all of these operations, the computer makes a large number of measurements in seconds and returns information that could not be realistically obtained by manual methods.

Jan 1, 1992

By M. T. Ernett

Significant amounts of arsenic are often present in effluents arising from the mining of sulfide ores for the extraction of metals such as copper, gold, lead and zinc. The arsenic is usually removed from the process effluent by co-precipitation with iron because of its common occurence in the mined ore bodies and the excellent adsorptive property of the precipitated hydrous ferric oxide compound. There has been controversy, however, over the long-term stability of the arsenic-bearing ferrihydrite which is produced. This paper presents the results of laboratory studies which indicate that the cations of calcium, magnesium, zinc, cadmium and lead, increase the pH range of effective arsenic adsorption in the Fe-As precipitate from 4-7 to 4-9. The increase in the pH range is similar for all of the added cations investigated. Sulphate ions are shown to have a minimal effect on the residual dissolved arsenate concentration. Silicate ions reduce the adsorptive capacity of ferrihydrite if they are present before the arsenic is adsorbed.

Jan 1, 1994

A simulation of a capper concentrate smelter was built with a capacity of 450,000 tons per year. The system's components to simulate were three : a Reverbetory furnace, a Wiente ' s modified converter ( TMC ) and two cranes. The system was classified as dynamic, stochastic and discrete. In the simulation language choice it was concluded that the most advantageous one was GPSS/H. The model verification was done through the interactive Debugger that the language has and the statistical validation was done through the result variables of sane activities, that as a whole characterize the system (charged matte and charged concentrate to the TMC, skimming white metal and skimning slag). The validation was done comparing the simulation results of these variables with the ones obtained for those variables in a specific month in the smelter. The comparison consisted in a difference of means test and in all cases the equality was accepted with a 95% of confidence. The animation tool was PROOF, a general purpose animator, that is used after processing the simulation.

Jan 1, 1994

By Ian Masters

Rotary furnaces are widely used throughout the metals industry. These furnaces vary in size and geometry, but are fundamentally the same from a thermodynamic viewpoint. A generic method is proposed that can be used to model all furnaces of this type, provided that the correct material and process parameters are known. Various approaches have been attempted in the past based on a continuum (FEA or CFD) approach. However, the complex fluidlsolid interactions present in a rotary vessel are not easily solved using these methods, which work best where the material boundaries are well defined. In this paper a lumped parameter model is proposed. Variations within a section of the model are ignored, but to ensure thermodynamic correctness, the heat transfer between sections is carefully considered. For example, it is reasonable to assume that the whole of the melt pool is at the same temperature, due to rotary mixing. This may then be modeled with a single set of parameters, and the detail is contained in obtaining the correct heat transfer mechanisms from the rest of the furnace.

Jan 1, 2002

By David Rees

Tomago Aluminium, a 400,OO tonnes per annum primary aluminium smelter in Australia, has installed Ozone for biological control of its process water. The system was designed in Australia by Ionics Watertec Engineering, whilst ANCO Australia monitors the water quality and provides technical support for the project. The motivation was initially to reduce operating costs, however investigations indicated that there were substantial environmental benefits to be achieved by the elimination of a part, or all of, the chemicals being used to control the system. Also the existing chemicals appeared to be losing their ability to control biological growth in the system, in particular, the legionella bacteria. Ozone water treatment commenced in January 1998 and after a short transition period has operated without chemical addition since. There appears to be no doubt that the biological control is effective, the clarity and purity of the water has improved and initial testing indicates that the corrosion control rate is acceptable, although some chemical corrosion control may be introduced after further testing around the total circuit to guarantee protection

Jan 1, 1999