Search Documents

By Jewel A. G. Gomes

Lead has long been an USEPA priority pollutant and an important environmental and health concern because of its toxicity at ppb levels. In light of health and exposure data for lead, the EPA has set standards for Maximum Contaminant Level (MCL) and a MCL Goal (MCLG) as 15 ppb and 0 ppb, respectively. An accurate and rapid measurement of lead in the field remains a technical challenge. In this work, a relatively new method of deploying a nanoband electrode system using anodic stripping voltammetry has been optimized by changing deposition potential, electrolyte, and plating time used for the measurement of Pb(II) in water samples. Green rust has been proven to be an efficient intermediate matrix for removal of lead contaminants. We also report here the removal efficiency of lead using green rust produced by electrocoagulation, both directly and indirectly. Lead containing floc was also characterized through XRD, SEM, and EDAX techniques.

Jan 1, 2008

By Zhenglong Li

A process has been developed to recover titanium from a blast-furnace slag which contains about 20-25% Ti02 and 12% Fe. In this process. "hot" slag from the blast furnace is directed to a separate furnace where it is reheated with additives to form two simple slag phases: one is titanium enriched anosovite (Ti3O5) and the other is a titanium lean non-crystal glass phase. The modified slag is then processed by conventional beneficiation techniques to produce a marketable titanium concentrate and a usable slag material. This paper focus on separating anosovite from glass by electrostatic separation and froth flotation.

Jan 1, 1996

By David S. Holmes

An overview of existing biological technologies for the recovery of copper and uranium is presented. Engineering and biological challenges and opportunities in these areas. are discussed. New opportunities for the biooxidation of refractory gold ore are described. Techniques for the development of new strains of microorganisms. for commercial metal recovery applications are discussed with special reference to the genetic manipulation for bacterial strain improvement.

Jan 1, 1991

By W. D. Keller

Scanning electron microscopy (SEM) accompanied by X-ray energy dispersive analysis (XES) is a useful tool in process clay mineralogy. The texture of kaolin, illustrated by SEM, gives a clue to its mode of genesis and probable industrial application. One type of kaolin, originating dominantly by weathering, has an open texture, slakes readily, and is used for filling and coating paper. Another type, in contrast, originates by diagenesis of Al-silicate sediments, and spectacularly resists slaking, thereby enabling it to maintain its bulk density and controlled size and shape of particles after crushing and moistening; this meets an important requirement for the manufacture of refractories. Ratios of elemental Al:Si that may be rapidly determined by SEM and XES yield information on the origin and purity of bauxite and bauxitic clays, and aid in quality control and processing of them. SEM of dissimilar textures of quartz, as in chert and novaculite, are evidence for geothermometry on a stratigraphic scale that is potentially useful in delimiting thermally favorable or unfavorable areas for hydrocarbon exploration, and possibly for unexposed metallic ore deposits.

Jan 1, 1982

By Maija-Leena Metsiirinta

The behaviour of copper and lead in zinc roasting has been studied in laboratory scale roasting experiments as well as in large scale trials in an industrial fluidized bed, with the background of Outokumpu Kokkola Zinc smelter. Commercial zinc concentrates with a low and high ( up to 3 wt % ) copper content and with a low and high ( up to 3.5 wt % ) lead content were oxidized to various desulphurisation degrees in the fluidized bed to establish the reaction mechanisms and the paths for copper and lead oxidation in the roasting. Influences of the agglomerate size on the roasting kinetics and micro- scale phenomena were also determined. Optical microscopy was used on the calcine and the findings are presented as numerous photographs of the polished cross sections. SEM/EDS techniques were used for analyzing chemically the phases and particle morphologies present in the samples. Computational thermodynamics was applied to the complex phase equilibria occurring during roasting in the agglomerating calcine. A complete oxidation of zinc concentrate with a high copper and lead content requires a careful control of oxygen coefficient in the roasting in order to maintain a stable operation of the fluidized bed. Oxygen coefficient thus seems to have a significant impact on the hydrodynamic stability of the fluidized bed with fine raw materials.

Jan 1, 2003

By Maija-Leena Metsärinta

The behaviour of copper and lead in zinc roasting has been studied in laboratory scale roasting experiments as well as in large scale trials in an industrial fluidized bed, with the background of Outokumpu Kokkola Zinc smelter. Commercial zinc concentrates with a low and high ( up to 3 wt % ) copper content and with a low and high (up to 3.5 wt % ) lead content were oxidized to various desulphurisation degrees in the fluidized bed to establish the reaction mechanisms and the paths for copper and lead oxidation in the roasting. Influences of the agglomerate size on the roasting kinetics and micro-scale phenomena were also determined. Optical microscopy was used on the calcine and the findings are presented as numerous photographs of the polished cross sections. SEMIEDS techniques were used for analyzing chemically the phases and particle morphologies present in the samples. Computational thermodynamics was applied to the complex phase equilibria occurring during roasting in the agglomerating calcine. A complete oxidation of zinc concentrate with a high copper and lead content requires a careful control of oxygen coefficient in the roasting in order to maintain a stable operation of the fluidized bed. Oxygen coefficient thus seems to have a significant impact on the hydrodynamic stability of the fluidized bed with fine raw materials.

Jan 1, 2003

By A. J. van der Zeeuw

The use of SME 529 in the extraction of copper from acidic liquors and of copper and nickel from ammoniacal solutions, is illustrated with results of laboratory and bench scale mixer/settler experiments. Special features of SME 529 are its high loading capacity and the ability to keep the complexes dissolved in the organic phase up to quite high concentrations.

Jan 1, 1976

By Keiji Toyabe

Several purifying techniques have been developed for controlling the impurity levels in the copper electrolyte at Niihama Copper Refinery. These have been carried out as follows; i ) the study of the reaction in liberation made it possible to raise the current efficiency for arsenic removal by more than 50% and to decrease generation of arsine sharply. By applying this method, a good performance was attained at commercial operation. li) the antimony in the electrolyte can be successfully removed by contacting it with activated carbon. This procedure is applicable particularly when there is a large amount of antimony in the copper anode. lli) for the nickel sulphate recovery from the electrolyte, an electric evaporating system was developed. The characteristics of this process are, capability of continuous operation with less manpower, the high recovery ratio of nickel sulphate (more than 85% as nickel) and no black acid formation in the treated solution.

Jan 1, 1987

By Tao Zeng, Jianchao Li, Chang Jie, Jieyu Zhang, Jifang Xu, Kuochih Chou

"The densities of the selected quaternary Ca0-5%Mg0-Alz03-Si02 slag with low silica were measured by the Archimedean method in a wide temperature range from l 723K to 1823K. Slag compositions were chosen based on five different levels of Si02 content between 0.00 pct and 11.40 pct. The MgO content was equaled to 5.00 pct. The mass ratio of CaO/Alz03 was varied from 0.67 to 2.14. The effects of temperature, Ca0/Alz03 ratio and optical basicity were studied. It is shown that density decrease approximately linearly with an increase in temperature. With the same Si02 content, the density decreases with increasing of CaO/Alz03 ratio and optical basicity. Based on the experimental data as the boundary of the homogenous phase region predicated by F ACTSAGE software, the mass triangle model is used to calculate the density of selected limited homogenous phase region. The results showed that the mass triangle model is working well.IntroductionIt is of great importance to measure density of slag melt not only to the theory research for melt, which that is directly amenable to the structure correlations of molten slags, but also to the industrial application. Many metallurgy phenomena such as inclusion formation in molten melt and its removing, slag foaming, slag-metal reaction are closely related to the density of slag. Density is also required to estimate other fundamental properties, like surface tension, viscosity, and thermal conductivity from thermal diffusivity so that a relatively complete picture in regard to the behavior of high-temperature molten oxides could be made."

Jan 1, 2013

By A. A. el-Geassy

High-grade iron ore fines rejected from the DRl plants (>96%Fe20) were isothermally reduced in 30-60%COIH2 gas mixtures at 973-1273K. The freshly reduced reaction products were then subsequently carburised in either H2/CO or H2/CO/S mixtures at 823-1073K for 30-120 min. The thermogarvimetric technique was used to follow up both of reduction and carburisation reactions as a function of time. The carburised samples were characterized by X-ray and Mossbauer techniques. Chemical and carbon analyses were also applied. The influence of temperature and gas composition on the reduction behavior was investigated. The calculated values of apparent activation energy, application of gas-solid mathematical formulations were correlated with the microstructures to predict the reduction mechanism, The influence of carburization time, temperature, CO contents in H2/CO or H2/CO/S were investigated. A conversion extent of Fe to Fe3C was taken as a measurable index for the efficiency of carburization reaction under the different experimental conditions.

Jan 1, 2003

By A. A. EI-Geassy

High-grade iron ore fines rejected from the DRI plants (>96%Fe2O3) were isothermally reduced in 30-60%CO/H2 gas mixtures at 973-1273K. The freshly reduced reaction products were then subsequently carburised in either Hz/CO or H2/CO/S mixtures at 823-1 073K for 30-120 min. The thermogarvimetric technique was used to follow up both of reduction and carburisation reactions as a function of time. The carburised samples were characterized by X-ray and Mossbauer techniques. Chemical and carbon analyses were also applied. The influence of temperature and gas composition on the reduction behavior was investigated. The calculated values of apparent activation energy, application of gas-solid mathematical formulations were correlated with the microstructures to predict the reduetion mechanism. The influenee of carburization time, temperature, CO contents in H2/CO or H2/CO/S were investigated. A conversion extent of Fe to Fe3C was taken as a measurable index for the efficiency of carburization rcaction under the different experimental conditions.

Jan 1, 2003

By V. A. Luganav

The behavior of arsenopyrite under heating has been studied by many scientists. It has been already established that under heating at more than 650°c and without air access the arsenopyrite dissociates with the formation of one atom arsenic. Under vacuum the dissociation process begins at 5500C with the formation of elemental arsenic. The residue of dissociation process contains pyrrhotite and throilite. In the presence of pyrite, arsenopyrite dissociates under lower temperature and with a higher velocity than without it. The industrial realization of fool scale processing of arsenic bearing raw materials is possible only by the use of standard equipment and oxygen containing blast. In this view the paper presents the results of the study on the effect of oxygen in the gaseous phase and its addition into the charge of pyrite in the process of arsenopyrite decomposition. Thermodynamic analyses showed that under thermal processing of arsenopyrite in the presence of pyrite and limited quantities of oxygen in the gaseous phase the formation of arsenic sulfides is possible according to the following reactions:

Jan 1, 2003

By H. Soto, J. Jara, F. Nava

A method has been developed to recover cyanide and copper from solutions containing copper complexes and thiocyanate. Copper is precipitated as copper thiocyanate or as copper cyanide depending on pH and the concentrations of thiocyanate and cyanide in the effluent. The copper precipitate assays over 50% copper and presents good dewatering characteristics. After settling it can be separated from the effluent by filtration. The solution containing the bulk of the cyanide is then oxidized with ozone to transform the remaining thiocyanate into cyanide. This results in a regenerated solution rich in free cyanide that can be recycled to the cyanidation process. Careful control of the pH of the solution is required. First, pH of the effluent is lowered to optimize the precipitation and oxidation stages, then the pH is restored to an alkaline value to regenerate the cyanide solution. Recoveries of over 96% copper and cyanide were obtained in laboratory tests using industrial solutions. With this procedure, cyanocidic gold/copper ores could be treated economically by heap leaching, since the cyanide consumed by the copper impurities could be regenerated at very low cost (most of the cost of cyanide regeneration would be compensated by the copper credits). In order to achieve this, a bleed of the barren solution could be treated by the proposed method, and then recycled to the leaching step. The volume of solution to be treated should be large enough to keep a cyanide/copper molar ratio higher than 3:1. This would assure that copper does not cause undue interferences in the leaching or the carbon adsorption stages. If the thiocyanate content is low, the oxidation stage can be avoided, and the solution can be recycled to the leaching stage directly after the solid-liquid separation stage.

Jan 1, 1997

By Adrian C. Deneys, David G. C. Robertson

"Fluid flow phenomena on the surface of a molten slag have been documented using video photography in a laboratory scale D.C. arc furnace. The flow on the surface of the slag appeared to be electromagnetically influenced. This was confirmed by varying the position of the anode, which changed the direction of flow on the surface of the slag. Temperature measurements in the bath also confirmed the change in the directional nature of the fluid flow induced by the arc.During some periods, solids were fed into the arc attachment zone (AAZ) down the center of the hollow graphite electrode. Significant movement of the arc around the basal annular surface of the hollow electrode takes place. The point of attachment of an arc on a hollow electrode was more variable than an arc attached to a solid graphite electrode. Video images showed that the solids were rapidly incorporated into the bulk of the slag. Temperature measurements confirmed the existence of a superheated slag layer at the slag-gas interface, which allowed the solids to be rapidly incorporated into the melt.This work has been conducted to study fluid flow, temperatures, and solid behavior during feeding, in the arc attachment zone of a D.C. arc furnace. The work also has relevance to optimizing furnace design for pyrometallurgical slag cleaning processes."

Jan 1, 1999

By C. Burton Clark

The important role of the petrographic microscope in the petrology of refractories is discussed, based on 45 years of industrial experience by the author. Highlights of his career are used to illustrate improvements in equipment and techniques during the period. Two specific investigations are described which emphasize the interrelated use of the petrographic microscope with other instruments such as the x-ray diffractometer and scanning electron microscope. Emphasis is placed on the use of phase equilibrium diagrams for guidance in predicting and interpreting reactions that occur under non-equilibrium conditions in the manufacture and use of refractories.

Jan 1, 1982

By L. A. Neumeier

The Bureau of Mines, U.S. Department of the Interior, is investigating the feasibility of partitioning complex sulfide minerals to simpler sulfide .phases by sulfldation reactions. Such partitioning can afford opportunity to improve selective extraction of mineral constituents of value. This report describes initial research involving sulfidation partitioning of chalcopyrite concentrates. Small chalcopyrite samples were sulfidized with elemental sulfur in glass capsules sealed after evacuating and backfilling with helium, by heating for 1 to 24 h at specific temperatures in the range of 250° to 500° C. which extends from below to above the boiling point of sulfur (-445° C). Above the boiling point of sulfur, the overall reaction with adequate sulfur (13.9 wt pct of CuFeS2) is 5CuFeS2 + 4S g ? Cu5FeS6 + 4FeS2.

Jan 1, 1989

By N. A. Barcza

DC plasma-arc technology using a hollow graphite electrode (cathode) has been successfully implemented in the primary metallurgical industry in South Africa up to the 30 MW scale. Mintek has applied its expertise base, established over the past fifteen years, to testing the treatment of metallurgical wastes such as carbon- and stainless-steel plant dusts, lead- and zinc-containing slags, and residues from the base-metal industry. Favourable results have been achieved, and disposable products were produced. The evaluation of numerous wastes indicates that recovery of zinc as metal gives the best economic return from these sources. Direct recovery via a splash condenser or electrolytic zinc extraction from fume are the two preferred alternatives under review. In both instances dehalogenation is an important issue, but can be achieved by suitable treatment processes. The Enviroplas technology provides a flexible, commercially viable approach to the treatment of a wide variety of wastes. Mintek, together with its associate Pyromet CC, are installing a plasma- arc pilot-plant facility with both an ISP lead-splash condenser of about 5 t/d condensed zinc capacity and a combustion chamber to burn zinc vapour to zinc oxide. This will demonstrate the suitability of the Enviroplas technology for treating specific metallurgical wastes, so that customized industrial plants can be engineered based on large-scale testwork.

Jan 1, 1994

By Veena Sahajwalla

The cupola furnace is a coke-fueled shaft furnace used as a primary melting unit in iron foundries. Control of chemical composition of the iron tapped from the cupola is a key factor in productivity and quality control. In an effort to develop a control model for the cupola, a fundamental approach based on physical and chemical principles has been taken to describe the melting process. The behavior of oxidation of the solid charge in the stack of the cupola has been studied. Sulfidation of the charge materials by sulfur-bearing components released to the furnace gases from the coke has been described. Carburization of metal droplets of iron and of steel in separate molten streams has been characterized. Finally, reactions with alloying elements in the hearth (well) of the furnace have been defined. These reactions have been described in a computer-implemented model developed to predict the composition of the iron tapped from the cupola. The model has utilized the thermodynamics and kinetics of the oxidation, sulfidation, and carburization reactions, including temperature and physical aspects, in the various zones of the melting unit. The model predictions have been compared favorably with operating results.

Jan 1, 1992

By P. M. Prasad

The last two decades have witnessed the emergence of numerous hydrometallurgical and direct processing techniques for the extraction of some metals from pocketed/lean/complex sulfide ore deposits. A new approach with some inherent technological merits, investigated in recent years, is the lime-enhanced reduction of metal sulfides. Thermodynamic aspects relevant to the lime-enhanced reduction of metal sulfides by H2,C0 and C are discussed. A survey of the researches on the basic features of and factors influencing the lime-scavenged reduction of selected sulfides and sulfide concentrates reveals that lime tremendously enhances the sulfide reduction rates (up to 100 times) and drastically reduces the sulfur emission into off-gas to negligible levels. Further successful practice of lime-enhanced reduction requires only a moderate temperature of reduction (characteristic of each sul¬fide) and, in the case of gaseous reduction, relatively low gas flow rates. Relevant kinetic aspects of the concerned reactions that have a bearing on process development and its understanding are also briefly discussed. A conceptual scheme of general applicability for the processing of sulfide concentrates by the lime-enhanced reduction technique consists of three main steps: (0 lime-enhanced reduction by a suitable reagent (e,g., H,2, CO, gasified coal, water gas), (ii) separation of the product metal from the dry slag (CaS + unused CO) by mechanical separation, magnetic/gravity concentration or flotation and (iii) melting and refining by standard procedures. This novel approach, which is patently less complex, is expected to employ basically simpler flow sheets at comparatively lower operational temperatures and aid in pollution abatement. Potential for developing such a route for the small scale extraction of metals like copper, molybdenum and antimony is indicated. Possibility of utilizing this technique for the production of fibers/ filaments of some metals is also outlined.

Jan 1, 1983

"EAF dust is categorized as a hazardous solid waste. EPA approves only two treatment methods: either sending the dust to zinc recycling facility, or stabilizing it first and then disposing it to a specially-lined landfill. Both treatment methods are costly to EAF steelmakers. In order to reduce the cost and even better to make profit from the dust, EAF steelmakers need to find a costeffective technology to separate zinc from EAF dust. This paper is dedicated to discussion of a novel recycling strategy: in-process separation of zinc from EAF dust. The concept of in-process separation of zinc from EAF dust is first defined, and then a simple Zn concentration model is developed. From this model, two approaches of in-process separation of zinc from EAF dust are derived: (1) prematurely capturing dust at very high temperature when zinc is still in vapor status, (2) prematurely collecting dust immediately after quickly cooling EAF off-gas from high temperature to low temperature. Next, thermodynamic analysis is conducted to understand zinc behavior in EAF off-gas. It is demonstrated in theory that zinc is in vapor status while it exits from electric arc furnaces. At last, recycling routes and economics of in-process separation of zinc from EAF dust are discussed.IntroductionElectric arc furnace (EAF) plays an increasingly important role in steel production. According to USGS, steel production from electric arc furnaces has long exceeded that from basic oxygen furnaces [JJ. In 2009, electric arc furnaces produced 64% of total steel in the United States.Along with the fast growth of EAF steel production, generation of EAF dust is also rapidly increasing. A survey by AIM Market Research showed that 10 - 20 kg EAF dust was generated for every ton of EAF steel produced [2] In 1999, the United States alone produced 770,000 metric tons of EAF dust [3] In Europe, annual generation rate of EAF dust is more than one million tons [4-5]. In Japan, about 450,000 tons of EAF dust is produced each year [6] Globally, total generation of EAF dust was estimated to be more than 5 million tons per year [5] EAF dust is categorized as a hazardous solid waste since it often contains heavy metals, such as lead, chromium and cadmium. US Environmental Protection Agency (EPA) approves only two methods for treating EAF dust: (1) recycling the dust by EAF-dust recyclers, and (2) specially landfilling the dust for disposal after it is chemically stabilized. These two methods of treating EAF dust are both very costly to EAF steelmakers. It was estimated that a fee of $150 to $200 per ton of EAF dust was paid for various treatment options, which added approximately $2 - 3 cost for every ton of liquid steel produced by electric arc furnaces [?J."

Jan 1, 2011