Search Documents

By F. X. Prins, L. R. Nelson

Tight control of electrode paste additions, hard and soft paste levels, baked zone position and electrode temperatures are integral to superior Söderberg electrode management practices. Paste addition is typically effected through briquettes, cylinders or large blocks. Each electrode paste form has its advantages and disadvantages, but probably a more crucial element from an electrode control perspective is the frequency and amount of electrode paste addition into a Söderberg electrode column. The detrimental effects of excessive soft paste levels leading to Stokes? Law segregation of paste in the electrode column are well documented, while several operators have effectively implemented the use of electrode thermocouples to monitor paste temperatures and automated slipping algorithms to control baking conditions within electrodes. Somewhat less well appreciated are the negative influences of inadequate soft paste levels, especially when coupled with excessive paste cylinder or block additions and resulting high hard paste levels. The alternative of insufficient hard paste levels and associated overheated electrode paste must also be considered, and can contribute to paste segregation directly. This condition also has the potential to generate gas mixtures in the electrode column that are concurrently a potential health hazard, while being prone to spontaneous combustion. Results of industrial trials on electric furnaces using Söderberg electrodes in a variety of applications from ferrochromium, to ferromanganese and even platinum-bearing base metal sulphides smelting are presented to illustrate the influence of paste loading practices on the dynamics of hard and soft paste levels. Possible electrode failure mechanisms attributable to inadequate paste level control will be discussed through some industrial examples. Suitable paste loading practices to mitigate the risks of inappropriate paste levels and associated electrode incidents are presented.

Jan 1, 2004

By M .. Hori, H. Onishi, Y. Goda

The split-lining structure was newly developed for the air-tight lining of the underground compressed air storage cavern. This structure consists of separated reinforced concrete (RC) segments and air-tight membrane. It is most important for the Compressed Air Energy Storage Gas Turbine (CAES-G/T) system to develop the economical lining. In order to verify the applicability of split-lining structure, CAES-G/T pilot plant was constructed and operated for 6 months. We confirmed the practical usefulness and safety of this system through the operation. This paper presents the mechanical behaviour of surrounding rock mass and the lining structure observed through the operation of CAES-G/T pilot plant. Nous avons mis au point une structure de revêtement modulaire pour le revêtement des cavernes souterraines hermétiques à pression. Ce revêtement est composé de segments de béton armé et de membranes hermétiques. Il était très important, pour le CAES-G/T (Compressed Air Energy Storage Gas Turbine), de développer un revêtement économique. Afin de vérifier l’aptitude d’application de notre revêtement modulaire, nous avons construit un système pilote CAES-G/T et nous avons effectué des essais de fonctionnement pendant six mois. Ces essais nous ont permis de confirmer l’utilité et la sécurité du système. A travers le présent rapport, nous rendons compte de la structure de ce nouveau type de revêtement et du comportement mécanique de la masse rocheuse environnante que nous avons pu observer au cours desdits essais. Als luftdichter Druckbehälter wurde eine gegliederte Belagsstruktur für tief unterirdisch liegende Felshöhlungen entwickelt. Diese Struktur ist aus Stahlbetonabdeckung und luftdichter Plane aufgebaut. Bei der Entwicklung des Pressluftgasturbinen – Stromerzeugungssystems (CAES-G/T) war es die wichtigste Aufgabe, einen wirtschaftlichen Belag zu entwickeln. Deswegen wurde zum Nachweis der Effektivität der gegliederten Belagsstruktur eine Pilotanlage errichtet und 6 Monate lang betrieben. Durch den Betrieb konnten wir die Praktikabilität und Sicherheit des Systems bestätigen. Dieser Aufsatz ist ein Bericht über das Verhalten der durch Betrieb der CAES-G/T Pilotanlage beobachteten Belagsstruktur und umliegenden Felsmasse.

Jan 1, 2003

Standards And Laboratory Monitoring In Gold Assay Key Components Of Best Practice

Jan 1, 2005

By G. Taylor

A 21st Century worker is one who works less with his physical power and more with mental ability. Such a worker is more skilled than a labourer and is consequently rewarded accordingly. A21st Century supervisor is one who ensures that workers are constantly supported so that they can maximize safety and productivity. A 21st Century manager is one who constantly searches for ways to maximize returns for the various stakeholders. Given the well-known constraints in narrow reef mining, all of the above is meaningless unless a mining method is found which provides conditions which support the 21st Century initiatives. [ ] The identified mining method is a continuous non-explosive stope breaking system using rocksplitter technology. Rocksplitting is defined as: The fragmentation of rock through high energy pulse wave transmission in a fluid-filled hole or hydro fracturing. Shotholes are effectively filled with a water-based geland 30 grams of explosive after which the hole is closed off with a ?rocksplitting gun?.

Jan 1, 2000

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameter like commodity price, mining or processing cost, stripping ratio, etc. The most important characterization of these push backs is that the innermost push back has the highest value per ton, the second innermost push back has the second highest value per ton, and so on. These nested pits are generated based on the best estimates of grade within a representation of the orebody in a three-dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion, grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduces a new algorithm that incorporates ore grade uncertainty during the pushback design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence. Keywords: open pit mine, push back, ore grade uncertainty.

Jan 1, 2007

By M. Tangstad

Keywords: Pyrometallurgy, ROMA, Norway, furnace, fines The ROMA project is a competence project on optimizing the usage of raw materials and energy in the ferromanganese, silicon, and aluminium industries. One of the items investigated in this project is the effect of fines on the furnace, and the usage of agglomerates versus lumpy ore. From lab-scale experiments it is shown, that for the charge to agglomerate in the furnace, the charge has to be exposed to a temperature higher than about 1200°C, independent of fines content. The fines less than 1 mm also showed higher agglomeration properties, compared to 2?4 mm, which showed no agglomeration property at all. The properties of agglomerates are very dependent on the pre-treatment of the agglomerate. Sinter and pellets, which have been heated to high temperatures, show a better strength, but also a lower CO reactivity. Sinter also shows a lower melting temperature compared to the ore.

Jan 1, 2011

By D. Schreuder

Conditions in the South African market relating to atmospheric emission control has changed dramatically over the last 10 years. Companies have become more responsible, environmentally aware, and have to comply to more stringent environmental limits set by legislation. This paper describes briefly the current best available atmospheric pollution abatement technologies relating to particulates, acid gases, NOx, acid mists, aerosols, mercury, dioxins and furans. Mention is also made as to the best practices for product work-up and waste product disposal.

Jan 1, 2006

By T. Saito, S. Murata

An original concept of JRC-diagram that can evaluate JRC and its size-effect by using a fractal model was proposed. In order to confirm the applicability of the JRC-diagram, first, JRC of the tensile fracture surfaces of a granite and a sandstone were evaluated by both the JRC-diagram and Barton's JRC-profiles, and then, it was compared with the JRC inversely calculated from the peak shear strength that is obtained from the shear test for each fracture using Barton's empirical equation. As a result, JRC evaluated by the JRC-profiles was much smaller than the inversely calculated JRC. On the other hand, it became clear that JRC evaluated by the JRC-diagram is almost the same with the inversely calculated JRC, if the size of interlocking is evaluated correctly. Therefore, for the JRC evaluation, it is thought that the JRC-diagram is more applicable than the JRC-profiles. Als ein neues Verfahren zur Bewertung des Rauheitsindexes JRC für die Bruchfläche von Felsenschichten anhand eines fraktalen Modells, wobei auch der Maßeffekt berücksichtigt wird, wird ein JRC-Diagramm vorgeschlagen. Um die Angemessenheit der Bewertung vom JRC mit diesem JRC-Diagramm festzustellen, wurden die JRC-Werte an einer Bruchfläche zwischen Granit und Sandstein sowohl mit dem JRC-Diagramm als auch mit dem herkömmlichen JRC-Profilverfahren bewertet. Anschließend wurden die durch die beiden Verfahren ermittelten Werten mit den JRC-Werten verglichen, die von den Schertestergebnissen mit Hilfe von Bartonschen Erfahrungsformel zurückgerechnet werden können. Daraus ergab sich, daß das JRC-Profilverfahren ziemlich kleinere JRC-Werte gibt als bei der Zurückrechnung, während die JRC-Werte durch das JRC-Diagramm unter entsprechender Bewertung des Ineinandergreifungsmaßes an der Bruchfläche beinahe gleich sind wie die zurückgerechneten Werte. Diese Tatsache weist darauf hin, daß das JRC-Diagramm eine bessere JRC-Bewertungsmethode als das JRC-Profilverfahren darstellt. Nous avons proposé le diagramme JRC, nouvelle méthode d'évaluer JRC qui est un indice de rugosité superficielle d'une fracture de roche à l'aide du modèle de fracturation, compte tenu de son effet d'échelle. Pour vérifier la validité de JRC évalué au moyen de ce diagramme, nous avons évalué JRC d'une fracture de roche, granite et grès, par le diagramme JRC et le profil JRC, méthode conventionnelle, et les résultats ainsi obtenus ont été comparés avec la valeur de JRC calculée en sens inverse à l'aide de la formule empirique Barton sur la base des résultats de l'essai de cisaillement des fractures. Il en résulte que la valeur de JRC obtenue par le profil JRC était assez faible en comparaison avec la valeur calculée en sens inverse alors que celle de JRC obtenue par le diagramme JRC correspondait approximativement à la valeur calculée en sens inverse à condition d'évaluer l'échelle d'endentement d'une fracture. Par conséquent, nous considérons que le diagramme JRC est une meilleure méthode d'évaluation de JRC par rapport au profil JRC.

Jan 1, 2003

By V. Labiouse, P. K. Kaiser, F. Descoeudres, F. Rojat

In this paper some failure phenomena observed in the crossing of brittle rock formations at the Lötschberg base tunnel are presented. A brittle failure criteria, recently developed by Canadian researchers, is applied through finite element calculations together with a semi-empirical failure criterion, to explain these behaviours. Good agreement is found between predicted and observed failures at the tunnel walls. This study also shows some of the limitations of this approach. Dans cet article sont présentés certains phénomènes de rupture observés durant la traversée de zones de roches fragiles lors de l’excavation du tunnel du Lötschberg. Un critère de rupture développé récemment par la recherche canadienne est utilisé à travers des calculs par éléments finis. En parallèle, les résultats sont comparés avec ceux d’un critère semi-empirique. Au niveau des parements, l’ampleur des ruptures observées est assez proche des résultats de calcul. Cette étude a également permis de mettre en avant certaines limites de l’approche choisie. In diesem Artikel werden verschiedene Brucharten dargestellt, die bei der Durchfahrung von sprödem Gestein im Rahmen des Ausbaus des Lötschberg-Basistunnels beobachtet wurden. Zur Erklärung des vorliegenden Verhaltens wurden die erst kürzlich in Kanada entwickelten Theorien zur Beschreibung von Sprödbrüchen herangezogen und bei der Berechnung mittels der Finite-Elemente-Methode und eines semi-empirischen Kriteriums angewendet. Die so vorhergesagten Versagenszonen an den Tunnelwänden stimmen mit den Beobachtungen gut überein. Die Studie hat auch dazu beigetragen, die bei der Anwendung des Lösungsansatzes angetroffenen Schwierigkeiten aufzuzeigen.

Jan 1, 2003

By S. Sakurai

We discuss the mechanical characteristics of underground structures that are subjected to vertical oscillations. Under such circumstances - expected when an earthquake rupture occurs very close to highly developed urban areas - the conventional seismic analysis, which mainly considers horizontal shear oscillations, may not be fully valid. Our analysis, based on the elastic wave theory, shows the effects of vertical disturbances and the generation mechanism of the unique damage patterns observed on the occasion of the 1995 Hyogo-ken Nanbu (Kobe) Earthquake. Wir diskutieren über die mechanischen Eigenschaften der unterirdischen Strukturen, die sich vertikalen Schwingungen aussetzen. Unter solchen Umständen - erwartet, wann ein Erdbebenabbruch sehr nah an hochentwickelten städtischen Bereichen geschieht - kann die herkömmliche seismische Analyse, die sich hauptsächlich horizontale Schubbewegungen überlegt, möglicherweise nicht völlig gültig sein. Unsere Analyse, basiert auf der elastischen Wellentheorie, zeigt die Effekte der vertikalen Bewegungen und den Erzeugungsmechanismus der einzigartigen Beschädigungsmuster, die anläßlich des 1995 Kobe Erdbebens beobachtet wurden. Nous discutons les caractéristiques mécaniques des structures souterraines qui s’exposent aux oscillations verticales. Dans ces conditions - s’attendent quand une rupture de tremblement de terre se produit tout près des secteurs urbains fortement développés - l’analyse séismique conventionnelle, qui considère principalement des oscillations horizontales de cisaillement, peut ne pas être entièrement efficace. Notre analyse, qui est basée sur la théorie des vagues élastiques, montre les effets des mouvements verticaux et le mécanisme de génération des modèles uniques de dommages, que nous avons observés à l’occasion du tremblement de terre 1995 de Kobe.

Jan 1, 2003

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By M. Karimi

Artificial neural networks (ANNs) have found their applications in the modelling of unit operations of mineral processing plants. In this research, laboratory-scale tests were conducted, using a three-inch diameter Mozley hydrocyclone. Main parameters included pressure drop at inlet, solid per cent, vortex and apex diameter were adjusted. The corrected cut size (d50c) and the flow rates of underflow and overflow were determined. Multi layers perceptron (MLP) feed forward network architectures were designed to predict the responses. The results showed a good correlation between experimental and network output, for corrected cut size and flow rates. Keywords: hydrocyclone, artificial neural network, corrected cut size, flow rates.

Jan 1, 2010

The gold concentration profiles which develop inside the activated carbon particles during the adsorption process were measured, so as to obtain additional direct proof of intra-particle mass transfer rate-control and to determine how individual carbon particles in a population vary in their gold uptake behaviour. The observed gold concentration profiles inside the activated carbon particles were typical of situations where an intra-particle mass transfer mechanism is rate-controlling. Gold di-cyanide penetrated the carbon particles with a wave-like front until it was uniformly distributed throughout the particle. This corresponds with the profiles predicted by the film and surface diffusion model. However, the rate with which gold di-cyanide was transported inside the individual carbon particles varied within the population of carbon particles. This variation was characterized by a lognormal distribution in surface diffusivity. Because the estimated variances of these surface diffusivity distributions were small, the dynamic adsorption behaviour of the carbons used in the present study did not deviate significantly from that predicted by a model based on film mass transfer and a single surface diffusivity. Van Deventer (1984, 1985 and 1986a) reported data that could not be adequately described by a model based on film mass transfer and a single surface diffusivity. In this study a model based on film mass transfer and a wide lognormal distribution of surface diffusivity values was applied to his data. It was shown that a population of carbon particles with a wide distribution in surface diffusivity values could offer an alternative explanation to the mechanism proposed by Van Deventer which was based on film mass transfer, with partitioning of the carbon into micro- and macropores with surface diffusion in the macropores and slow mass transfer into the micropores.

Jan 1, 1997

Excavations in rock are commonly supported with wire mesh, shotcrete, wire mesh and shotcrete in combination, and shotcrete reinforced with various types of fibres. Wire rope lacing and various types of straps are additional forms of support installed over the above types, to cope with severe conditions. These support systems are very important items of ?membrane? rock support. With the recent development of several types of thin sprayed linings, the importance of membrane support is likely to increase in the future. In this paper, a wide range of mechanisms of membrane behaviour and mechanisms of loading of membranes, is described. The concepts of membrane components, which are single membranes that may be used on their own as rock support, and membrane systems, which are combinations of more than one membrane component, are introduced. Different situations have different requirements of membrane support, and differences between civil engineering and mining requirements are highlighted. With the different basic requirements in these two areas, the requirements of rock support are correspondingly different. A thorough understanding of the mechanisms of behaviour of the different types of membranes, and the different mechanisms by which the membranes are loaded, is essential before a selection of appropriate support can be made, before appropriate design methods and calculations can be determined, and before appropriate performance test methods for membranes can be defined. The material in this paper contributes towards the understanding of membrane support behaviour.

Jan 1, 2001

By I. Jauhari, F. Stober, D. Fowler, B. O. Wasmund, T. Miraza, C. Nichols, A. Taofik Hidyat, K. Said

The existing PT Aneka Tambang (Antam) ferronickel smelter located at Pomalaa, Indonesia consists of two RKEF lines with reduction furnaces nominally rated at 17 MW and 18 MW, respectively. The low power densities and heat fluxes allowed both furnaces to operate with falling water film shell cooling systems. The furnace campaigns comprised a 5-yearly cold shut -down for metal taphole area rebuild and a 10-yearlysidewall and hearth perimeter repair. Towards the end of these campaigns the furnaces would typically be operated at below nominal power due to excessive sidewall temperatures. In January 2001 Hatch performed a smelter study which proposed options which indicated the possibility of a single furnace operation for the smelter, elimination of lime addition and transition to shielded-arc operation with associated efficiency and throughput gains. This paper discusses the process of uprating the second?line furnace capability from 18 MW to 32MW following the decision by Antam to implement the recommendations proposed by Hatch. It will cover the development of scaled-up furnace design basis by Hatch and Antam with the enabling application of Hatch cooling and binding technology. To optimise the capital cost and maximise Indonesian supply content and post installation support, the scope was carefully and clearly divided between Hatch and Antam. The challenges, set backs and valuable learning experiences gained during the implementation of the retrofit include; ?The support and re-use of existing roof system and challenges presented in re-use of existing crucible support steel. ?Training and technical assistance for Antam operators to perform refractory and copper cooler installation and maintenance of crucible integrity technologies. ?Hearth integrity during start-up and development of an initial charge and start-up procedure to achieve planned thermal expansion of the hearth prior to bath formation ?Implementation of a sidewall hold-down system within the refractory sidewall due to space constraints ?Existing furnace foundation reinforcement to overcome lateral forces on furnace piers during crucible support steel expansion ?Conversion of an open-loop gravity feed cooling water system to a closed loop pressurised system with integrated emergency gravity feed and backup system ?Existing water treatment system and pumping system improvement and modification to meet copper cooling system requirements ?Integration of the new instrumentation control system designed by Hatch to increase performance of the furnace monitoring system and operation ?Uprate transformer capacity from 25 MVA to 40 MVA to meet with requirement of Shielded- Arc Furnace Operation.

Jan 1, 2007

By M. J. Leeuwner

Computational fluid dynamic (CFD) modelling is used to research the complex flow structures that exist in a hydrocyclone. By simulation of a two phase (water and air) flow system, the internal flow and multiphase interactions are investigated. The suitability of CFD modelling as a design tool is further evaluated by examining the effect of varying device dimensions. Three hydrocyclone geometries, used in previous studies, are specified. A transient simulation approach, which employs the Reynolds Stress Model as turbulence model and the Volume of Fluid model as multiphase model, is followed. Results are validated qualitatively against experimental measurements from the previous studies. Keywords: CFD modelling, hydrocyclone, Reynolds stress model, multiphase flow

Jan 1, 2008

By A. Meek

This report compares the compressed air driven rocker shovel to the newly developed Warthog Non-throw development end loader. The two machines were compared on aspects such as safety, loading potential, energy efficiency and costs. The objectives of the comparison were to determine whether or not the replacement of the rocker shovel with the Warthog will be operationally and financially justifiable. The results from this study were obtained from underground observations and time studies on the machines, as well as consultations and data collection at the shaft and suppliers. This paper compares only the Warthog loader to the Trident 215 rocker shovel used at Anglo Platinum?s Brakspruit shaft and does not compare the other models of rocker shovels, which are fundamentally the same but will have different loading potentials and specifications. Cleaning times for the rocker shovel are based on underground observations at Brakspruit shaft. These times can be influenced by factors such as blasting practices, compressed air pressure and operator experience and skill. For this reason the times will most likely vary at different shafts. The Warthog cleaning times are based on manufacturer specifications and results from trial stages and therefore further work is required to confirm cleaning times achieved.

Jan 1, 2009

By V. Labiouse, B. Heidenreich

The rebound phenomenon, which occurs during rockfalls when a rock block impacts with a slope surface, is influenced by several parameters related not only to the slope material but also to the block and the kinematics. The paper presents a small-scale testing campaign undertaken at the LMR (EPFL) to better understand and quantify the bouncing of blocks on granular slopes. The influence of some factors related to the ground material, the block and the kinematics is examined. Bei Steinschlägen wird die Flugbahn eines stürzenden Felsbrockens maßgeblich durch den Abprall vom Hang bestimmt. Der Rückprall hängt von verschiedenen Parametern ab, wobei nicht nur das Hangmaterial sondern auch Blockeigenschaften und Kinematik eine große Rolle spielen. Zum besseren Verständnis dieses Phänomens und seiner Quantifizierung werden am LMR (EPFL) kleinmaßstäbliche Versuchskampagnen auf granulären Materialien durchgeführt. Der vorliegende Artikel stellt die Versuche vor und untersucht den Einfluss verschiedener Boden-, Block- und kinematischer Parameter. Le phénomène de rebond qui se présente lors de l’impact d’un bloc rocheux sur la surface d’un versant dépend non seulement des caractéristiques du terrain, mais aussi de facteurs relatifs au bloc et à la cinématique. L’article présente une campagne d’essais sur modèle réduit entreprise au LMR (EPFL) afin de mieux comprendre et quantifier l’impact de blocs sur des matériaux granulaires. L’influence de divers paramètres relatifs au sol, au bloc et à la cinématique est mise en évidence.

Jan 1, 2003

By Chris M. Haberfield, Neil D. Benson

The assessment of overall modulus (or stiffness) of a fractured weak to moderately strong rock mass is a key parameter in the design of civil engineering works in these materials. It also provides the highest level of uncertainty due to scale effects, anisotropy and the influence of joint frequency and joint stiffness. Using the example of the Melbourne Mudstone, this paper compares approaches using empirical rules based on intact rock strength, laboratory testing, in situ field testing, semi-quantitative assessment techniques based on rock mass classification and back analyses. L'évaluation du module (ou rigidité) global d’une masse rocheuse faible et fissurée a modérément forte est un paramètre principal dans la conception des travaux du génie civil dans ces types de matériaux. Elle fournit également le niveau le plus élevé d'incertitude due aux effets d’échelle, à l'anisotropie et à l'influence de la fréquence et de la rigidité des joints rocheux. En utilisant l'exemple du schiste de Melbourne, cet article compare des approches empiriques basées sur la force intacte de La roche, les essais expérimentaux au laboratoire, les essais sur site, les techniques semi-quantitatives d'évaluation basées sur la classification de la masse rocheuse et les analyses en retour. Die Schaetzung des allgemeinen Steifigkeit-Moduls des gebrochenen schwachen bis zu maessig starken Felsmassen ist eine Haupt- Annahme in dem Entwurf von Tiefbau-Projekten in diesen Materialien. Es verursacht den hoechsten Grad der Ungewissheit in Folge der Groessenordnung, Spaltorientierung und dem Einfluss der Haeufigkeit der Risse und Bruch-Steife. Unter Verwendung des Beispiels des Melbourner Tonsteine, vergleicht diese Darlegung die Anwendung der empirischen Regeln, die sich auf die Staerke des ungestoerten Fels Basieren mit Versuchen in der Material Pruefungsanstalt, Untersuchungen auf der Baustelle und halb-quantitative Schaetzungsverfahren, die sich auf die Felsmassen Klassifikation und fruehere Analysen stuetzen.

Jan 1, 2003

By H. J. Uananisa, M. J. Papo, C. W. Siyasiya, W. E. Stumpf

"SynopsisThe need to reduce weight while maintaining good mechanical properties in materials used in the automotive industry has over the years seen an increased exploitation of various steels to meet this new demand. In line with this development, the ferritic stainless steel family has seen a wide application in this industry, with the AISI 436 type increasingly being used for automotive trims and mufflers for exhaust systems, as well as a significant part of this steel’s application being for the manufacture of wheel nuts and wheel nut caps in trucks, mainly through the deep drawing process. However, there have been reports of some poor surface roughening of this material during deep drawing, with tearing and/or cracking also reported in some instances. This has been suspected to possibly be associated with some local differences in localized mechanical properties between grains and grain clusters of the rolled and annealed material.In order to investigate the poor surface roughness exhibited by AISI 436 ferritic stainless steel (FSS) during deep-drawing, Lankford values (R-mean and ?r), grain size, and microtextures of various sheet samples from this steel were studied. The chemical composition range for the samples was 0.013–0.017% C, 17–17.4% Cr, 0.9–1% Mo, and 0.4–0.5% Nb. The steels were subjected to various hot and cold rolling processing routes i.e. involving industrial direct rolling (DR) or intermediate annealing rolling (IR), and the drawability and final surface qualities of the steels were compared. It was found that the DR route gave an average R-mean and ?r value of 1.9 and -1.4 respectively, while the IR route yielded an average Rmean and ?r value of 1.6 and 0.52 respectively. The high ?r value for the DR processing route had a substantial adverse effect on the drawability. IR samples exhibited a smoother surface finish on visual inspection, while clear flow lines were visible on the DR samples, despite the fact that DR is the preferred industrial processing route due to the reduced production costs it offers. This observation was also confirmed through SEM examinations. The difference in the surface quality was attributed to microtexture. However, the mechanism responsible for this difference still needs to be identified."

Jan 1, 2015