Search Documents

By R. V. Higgins

This report presents computer instructions for calculating the performance of three-phase flow of gas, oil, and water. The calculated results for an illustrative example are presented. The example is the waterflood of a reservoir containing free gas in the reservoir as a result of the partial depletion of the oil by the expansion of the gas initially in solution. The flood pattern for the example is a 5-spot.

Jan 1, 1967

In 2007, a total of 2,030 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Coal mines comprised 13.7% of all mining operations. ? Bituminous mines comprised 92.4% (n=1,875) and anthracite mines 7.6% (n=155) of coal mining operations. ? Approximately 72% of all coal mines were located in three states: Kentucky (28.4%), West Virginia (22.6%), and Pennsylvania (20.5%).

Aug 1, 2009

By Young W. A.

The Eagle Silver mine is in the Rush Valley mining district, Tooele County, Utah, and is now operated by the Hampton Mining Co. The property, originally referred to as the Argent, is reported to have been one of the first discoveries in the district. The early operators mined ore to a depth of 850 feet, at which point the property was abandoned because of excessive water. During 1905 the Honerine tunnel was driven into the area approximately 1,800 feet below the collar of the Argent shaft. This tunnel served to drain the levels above and operations were resumed. Ore deposits in the Eagle Silver mine occur in the Galena King lime-stone, a 20-to 60-foot member of interbedded quartzite and limestone in the Oquirrh formation of Pennsylvanian age. This member has been faulted along the bedding, forming the Galena King gouge. Mineralization commonly occurs in or near this gouge area in a brecciated, highly altered, pipelike zone. The known ore shoots occur in association with the breccia pipe, commonly adjacent to cross faulting and porphyry intrusions. In general, two ore shoots have been mined on the upper levels of the mine, one lying to the east and the other to the west of the breccia zone. The Bureau of Mines diamond-drilling program was begun during the latter part of 1948 and completed early in 1949. Nine holes were drilled, aggregating 852.8 feet. Sludge and core samples from mineralized sections were analyzed in the Salt Lake City laboratories. A total of 87 sludge, 71 core, and 11 chip samples was submitted for analysis.

Jan 1, 1950

By Sam S. Taylor

[The discovery of many oil fields in Illinois since 1936 and their rapid development have brought tine problem of brine disposal to the foreground in that State. The ultimate magnitude of the is not yet known, but already it is great enough to warrant technical investigation. The Bureau of Mines, therefore, has made a general survey of the methods of handling oil-field brines in Illinois and has studied in detail three subsurfaces disposal systems.]

Jan 1, 1940

By Donald Giroux

This report documents the design, fabrication, testing, and coal mine demonstration of a hopper-feeder-bolter during a four-phase program for the U.S. Bureau of Mines. The machine was designed to increase productivity and safety in under-ground room-and-pillar mining. It performed well as a hopper-feeder for continuous haulage during a coal mine demonstration. Testing in a simulated mine showed that the machine also has good roof bolting capability.

Jan 1, 1987

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. [Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.]

By IRENE AITKENS

The emerald is the most costly of all gems , due to the scarcity of flawless stones . This fact gave rise to the ancient axiom , " As rare as an emerald without a flaw . The finer gems not only command the highest prices at all times , but when flawless are considered the most highly prized of all gem stones . George F. Kunz divides emeralds into two distinct classes : " Exceptional specimens , " which bring as much as $ 6,000 a carat ; and " fine- quality specimens , " which bring about $ 1,000 a carat .

Jul 1, 1931

By H. A. Thorne

This paper describing the mining practices at the Chino mines at Santa Rita, Grant County, N. Mex., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Nevada Consolidated Copper Co., Chino mine's, operates an open-cut copper mine at Santa Rita, Central mining district, Grant County, N. Mex. This mine is located about 16 miles east and slightly north of Silver City, the county seat. The ore is-transported in standard railroad cars by the Atchison, Topeka & Santa Fe Railway Co., approximately 10 miles to Hurley where it is milled. The concentrated are shipped approximately l'70 miles over the same railroad to the smelter of the American Smelting and Refining Co., at El Paso, Tex. (fig. 1)

Jan 1, 1931

By G. W. Grove, H. R. Burdelsky, F. E. Griffith

"INTRODUCTION The work of using a system of air locks in unsealing a mine in Ohio following a fire probably was one of the outstanding jobs of its kind in a medium-thick coal bed.The fire in this mine, thought to have been of electrical origin, was discovered at about 1:30 a.m. on December 11, 1941. Forty-four men were working in the affected section at the time; 5 escaped unassisted, and 37, who had barricaded themselves, were rescued. The bodies of two men, who had succumbed after breathing fumes given off by the fire, were brought part way out of the mine before it became necessary to seal the mine.Direct attempts to extinguish the fire with water were abandoned when hazardous amounts of 'carbon monoxide, methane, and other inflammable gases were detected in return air passing through the main haulageway and escape-way of the mine.The mine was completely sealed on the surface at about 8 p.m. on December 12, 1941, with the two bodies remaining in the mine. Sixteen days after the mine had been sealed, the two bodies were recovered. This was accomplished by air-locking through a partitioned-off stairs compartment of a ventilation shaft. This work was done under adverse barometric and atmospheric conditions.A method for collecting representative air samples from the immediate fire area was used successfully by utilizing a vacuum pump on about 10,000 feet of existing water line that had been broken near the fire area.The immediate fire region was sealed, and confined to a relatively small area; the remainder of the mine was recovered, and operations were resumed February 9, 1942, or 59, days from the time of sealing the mine on the surface. This recovery was made by air-locking the main entries inby from the shaft and No. 2 right-face entries.The distance between air locks averaged about 500 feet, and as each new set of seal stoppings and air locks was completed, the old or outby seals were taken out and the area between was ventilated. In ventilating this area, it was often necessary to use line curtains to direct the air into dead-end places."

Oct 1, 1947

By B. W. Madsen

The Bureau of Mines conducted a large-scale (6.4 t), long-term (2,165 days) test to gain a better understanding of the leaching characteristics of chalcopyritic ores. An ore sample containing 0.77 pct Cu was leached in a fiberglass column by downward percolation of acidified ferric sulfate solutions. Three sets of leaching conditions were investigated: (1) ambient temperature leaching, (2) elevated temperature (50° to 60° C) leaching, and (3) elevated temperature leaching after inoculation with thermophilic bacteria. Leaching at ambient temperature resulted in a copper extraction rate of 0.44 pct per 100 days. Increasing the temperature to 50° to 60° C resulted in decreased activity of natural mesophilic bacteria, and the leaching rate decreased to 0.22 pct per 100 days. The pH was lowered from 2.0 to 1.6, and nutrient solutions that contained thermophilic bacteria were added. This procedure resulted in an increase in the ferric-to-ferrous iron ratio and an increase in the copper leaching rate. However, the increased leaching rate was not sustained, and 120 days after inoculation the bacterial activity declined, the ferrous iron content increased, and the copper leaching rate decreased.

Jan 1, 1983

By T. D. Hackett

Multislice mining methods were analyzed by the U.S. Bureau of Mines to determine their application to western United States thick coal seams; ground control, geology, and costs were considered. Multislice mining is used in widely varying seam conditions worldwide, including flat seams too thick to mine in a single pass, pitching thick seams, and seams containing a rock parting. Longwall multislice methods predominate, but room-and-pillar variants also exist. The initial use of the method in western seams is planned at a deep Colorado mine where a rock parting will be used to separate two slices mined by longwall. Ground control and spontaneous combustion are major hazards associated with multislice mining. A well-consolidated upper slice gob can reduce ground control problems and provide a seal against spontaneous combustion. Geologic analysis indicates that the consolidation of the gob depends on the composition of the upper slice roof, the presence of water, and sufficient overburden pressure. A geologically competent intermediate rock parting can also reduce ground control problems and seal against spontaneous combustion. To compete in western coal markets, the cost of multislice mining must be within the range of normal longwall costs. Analysis indicates that multislice operating costs should be within this range, and that multislice mining costs decrease as panel width increases. Relatively wide (600 to 800 ft) panels also provide increased coal recovery.

Jan 1, 1990

By M. J. Kovalik

Lower Sunnyside seam coal from Utah was blended with various proportions of char and high-temperature coke to improve the quality of the coke obtained from carbonizing this coal. The Hanson 5-pound carbonizer was used as a "screening test" for the larger scale Bureau of Mines-American Gas Association (BM-AGA) tests, which were correlated with industrial production. Eighteen carbonization tests were made in the BM-AGA 13-inch retort, with a coal charge of about 90 pounds; the cokes were evaluated by the standard ASTM tumbler test. Carbonization of blends containing char and coke breeze yielded less fissured and blockier cokes of significantly higher ASTM I-inch tumbler indices as compared with the value for the straight Sunnyside coal. It was found that the simultaneous addition of char and coke breeze yielded stronger cokes than that obtained by the addition of either one of these additives. Addition of a small proportion of Pocahontas No. 3 or Sewell coal to an optimum blend improved the resulting coke strength further.

Jan 1, 1969

By Eugene T. Sheridan

This circular presents data on individual plants of the fuel-briquet and packaged-fuel industries that responded to the Bureau of Mines annual economic survey and reported production for 1959. The companies named herein represent virtually all producers of processed fuels of mineral origin. A few small companies may not have been canvassed or failed to respond, however, as some plants operate intermittently, and the survey is voluntary. No consideration was given to size of the plant and all plants that reported commercial production were included. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, fabricated from fine-sized mineral fuels by mixing with binders and compressing into small individual shapes. Briquets usually are produced as small, pillow-shaped pieces, 2 to 4 inches long, weighing 2 to 4 ounces. Packaged fuel consists of 3- to 4-inch cubes, 6 or 8 of which are wrapped in heavy kraft paper to form a package weighing 10 to 15 pounds. The overall size of a popular package is 10-112 x 7 x 3-1/2 inches. Briquets are durable, may be stored outdoors, and shipped and used as bulk fuel. Packaged fuel is fragile, and must be stored indoors to keep it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times as a supplement to other fuels. Package fuel is burned without removing the paper and referred to as the "white-glove" fuel.

Jan 1, 1960

By W. K. Sawyer

Resistivity, porosity, permeability, and saturation data were obtained on core samples from the Big Injun, Clinton, Gordon, Bradford Second and Third, and Venango Second oil sands and formation factor-porosity relationships were derived using the general form of Archie's equation F = aø-m, where F is the formation factor, ø is the porosity, and a and m are constants that depend on characteristics of the rock. It was found that a and m varied significantly between sands, as did the exponent in the Archie relation I = Sw-n, where I is the resistivity index and S, is the water saturation. The average exponent, n, determined from all data was 50 percent greater at residual oil saturation than at residual water saturation. Samples from each sand exhibited differences in directional resistivity and/or permeability. The Bradford Third sand data showed correlation between resistivity and permeability anisotropy.

Jan 1, 1971

By Richard D. Miller

This publication contains routine analyses and related source data for 350 natural gas samples from 19 States collected during calendar year 1362 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Helium Activity of the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus. Four previous publications have been made to present the results of 5,648 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1962. The first, Bulletin 486, 3/ contains analyses and data on 2,195 gas samples collected during the period 1917-47. Bulletin 576, 4/ the second publication, includes data and analyses for 1,575 samples collected from 1947 through May 1956. The third bulletin contains 1,444 analyses and source data of samples obtained from May 1956 to January 1, 1961.

Jan 1, 1964

By Richard D. Miller

This publication contains routine analyses and related source data for 350 natural gas samples from 19 States collected during calendar year 1962 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Helium Activity of the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus. Four previous publications have been made to present the results of 5,648 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1962. The first, Bulletin 486, 3/ contains analyses and data on 2,195 gas samples collected during the period 1917-47. Bulletin 576, 4/ the second publication, includes data and analyses for 1,575 samples collected from 1947 through May 1956. The third bulletin 5/ contains 1,444 analyses and source data of samples obtained from May 1956 to January 1, 1961.

Jan 1, 1964

By T. E. Swigart

In the production of oil end gas, engineering methods have been applied less than in any other branch of the oil industry. While refineries, gasoline plants, pipe-line and other transportation systems, and even drilling wells to a great extent, take advantage of engineering skill, the tendency has been to assume that the handling of producing wells is merely a mechanical and routine matter. At present few companies employ engineers to study oil and gas production methods with a view of increasing the general efficiency of recovery, but in vie, of the advancement in other lines of the petroleum industry by the application of engineering principles, does it not seem likely that the production branch may benefit also by engineering studies? Engineering applied to the handling of producing wells falls under two general headings, - first, the efficient handling of wells from the time of their inception in order to obtain the greatest possible ultimate production, and, second, the rehabilitation of old properties that have been handled carelessly in their early lives. To date, the engineering work that has been done on oil production problems falls mostly in the second class. For example, the use of vacuum and the application of compressed air have proved successful in some instances in stimulating wells of low gas pressure. These methods are costly to apply and are adapted to small wells in which the gas is almost exhausted, or in which the original gas pressure is negligible. The experiments described in this paper fall under the first heading, as they were made with an idea of learning toe probable extent to which the gas production of an oil well can be curtailed while gas in the sand is still plentiful, and thus saved for doing work during the later period of a well's life. Because of the scope of the experiments, this paper does not include a discussion of back pressure on flowing wells or for purposes other than cutting down the gas produced with each barrel of oil.

Jan 1, 1922

By R. Wiebe

During a recent investigation the authors were interested in determining: (1) How many points were necessary to locate the deviation curve for copper-constantan thermocouples within an accuracy of about 0.05° C., used in connection with the, "standard" thermocouple of L. H. Adams (2) Whether copper-constantan thermocouples showing considerable deviations from the "standard" were consistent throughout their calibration. (3) How reliable the extrapolated portion is - that is, the interval between -183 and -220° C. of the "standard" thermocouple.

Jan 1, 1931

By Walter Kawa

Bureau of Mines research on the hydrogenation of coal has been concerned with developing processes that could be used to supplement the Nation's petroleum and natural gas resources. Motor fuel was produced in a subsidized coal hydrogenation industry in Europe prior to 1945, but the process used is still not economical and other methods of producing liquid and gaseous fuels from coal are being investigated. As an aid to the planning of coal hydrogenation research, a literature survey was made of processes or methods of hydrogenating coal that differ from the subsidized or conventional process. This report contains a bibliography of unconventional methods of hydrogenating coal and a brief discussion of the economics of the conventional method. A general discussion of unconventional methods is included, and the advantages and disadvantages are pointed out where possible. The survey supplements a previous Bureau of Mines survey3 and a comprehensive review published in 1930.4

Jan 1, 1964

By N. H. Darton

In mining coal in the anthracite region of Pennsylvania the general custom has been to leave a large percentage of the coal in place as pillars to support the roof. Evidently any practice that involves partial waste of an important mineral resource is bound to be discarded. It is well recognized that one method of obviating probable waste is to fill the workings with cheap or worthless materials, a process extensively employed in the anthracite and some European mines. At present many of the collieries in the anthracite region of Pennsylvania are utilizing refuse from the old culm banks, which formerly were prominent features in the landscape, and are flushing the fine waste underground so that pillars may be reduced in size or removed. As a result the banks are now disappearing and soon will be gone. The fine culm from the breakers and rock from the mines will continue to be available, but the volume of these materials is insufficient to replace any considerable proportion of the coal removed. The next stage of progress suggested is the use of sand. Fortunately there are available large deposits of this material, much of which can be handled by dredges and pumps. This report is issued by the Bureau of Mines in the interest of safer and more efficient mining methods. I ts purpose is to describe the sand deposits in the northern anthracite coal field in Luzerne and Lackawanna Counties, Pa, Much of the information available is presented in the map, Plate I. Field studies, mostly preliminary, were made in the summer of 1911 to determine the distribution, amount, and character of the larger deposits. It was not thought desirable to make a detailed examination of the region because when the coal companies decide to utilize the sand their engineers will make precise surveys and drill test holes. In preparing the map the various coal companies were consulted; they contributed a large number of facts, especially as to the deposits in the buried valley of the Susquehanna between Pittston and Nan- ticoke, where nearly 1,000 test holes have been bored. The results of these borings were placed at the author's disposal, and have been utilized in drawing the boundaries given in the wide valley area and its extensions up Lackawanna River and NewportCreek. Wyoming Valley contains deposits of sand that are 100 feet thick over a wide area, 200 feet thick in places, and over 300 feet thick in the deep old channel south of Plymouth.

Jan 1, 1913