Search Documents

By I. Liebman

Two triggered barrier systems and several extinguishing agents were tested against coal dust explosion propagating in the main entry of the Bureau of Mines Experimental Mine at Bruceton, Pa. One system used a high-pressure cylinder to propel the extinguishant; the second system used pressurized nitro-gas or Halon 1301 (CF3Br) in a low-pressure system to power the disperser. The relative efficiencies of the extinguishants were determined by compar¬ing calculated concentrations of the extinguishant clouds present in the mine during suppressing of the explosions. Results showed the following trend of increasing effectiveness: Purple-K (KHC03)<water<hybrids consisting of foam or water combined with Halon 1301<Halon alone. On a weight basis, water was two to three times as efficient as Purple-K, whereas the hybrids and Halon alone were only marginally superior to water. Maximum efficiency of an extinguishant is attained by high rates of discharge from the barrier and by minimizing the time interval between onset of discharge and flame arrival to that necessary for discharge. Both the high- and low-pressure barrier systems were demonstrated to be capable of suppressing coal dust explosions; however, because of the potential hazard of the former, the low-pressure system is considered to be the most attractive prototype.

Jan 1, 1979

By Raymond O. Dannenberg

The gas-combustion retort developed by the Federal Bureau of Mines at the Rifle Oil Shale Project near Rifle, Colo., is a continuous, gravity-feed retort. The heat required to convert the kerogen in the oil shale to liquid oil is generated by the combustion of product gas and carbonaceous residue remaining on the retorted shale after the kerogen has been converted to oil, gas, and residue. A study of the effects of the process variables on retort operation, product yields, and product properties is important to the successful solution of the problems encountered in the development of a satisfactory process. Statistical methods were used to design the experiments and analyze the effects of the rate of shale throughput, the composition of dilution gas, the height of the shale bed above the air entry, air-gas distributor design, shale size range, and the ratios of the flow rates of the various gas streams entering the retort to the rate of shale throughput.

Jan 1, 1960

By R. E. Heithecker

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce, published a report of the gas at reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, nay be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937

By Heithecker R. E.

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce,, published a report of the gas reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, may be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937

In the interest of safety in underground coal mining, the Bureau of Mines recommends: 1. That doors used to control ventilation (a) Shall be installed in pairs to form air locks, (b) Shall be self-closing, (c) Shall not have latches or other devices for holding them open, (d) Shall be constructed and maintained to prevent excessive air leakage through or around them, (e) Shall be fire resistant. 2. That wherever practicable the use of doors shall be limited to development openings. The Mine Safety Board is of the opinion that the best practice in coal-mine ventilation makes use of a split system employing overcasts or undercasts with doors limited as far as feasible to development openings. The distance between air-lock doors on haulageways should be sufficient to accommodate a trip or train of maximum length. Where auxiliary doors are installed to control ventilation during emergencies, they should be so placed that they can be utilized readily in case of damage to the air-lock doors.

Jan 1, 1938

By Marshal Scherba

Coal seams approximately 7 feet, 9 feet and 20 feet thick at depths of 250, 600 and 1,000 feet respectively were detected using high resolution seismic reflection techniques. Investigation of seismic profiles indicates that good data are required to delineate faulting with only 20 feet of throw but that faulting with 50 feet of vertical displacement can be detected with poor data. Data acquired from dynamite charges fired in water saturated media were clearly superior to that acquired using charges dry tamped in 10 and 20 foot holes.

Jan 1, 1977

By P. A. Kennedy

An environmental assessment or impact statement for onshore waste disposal under the Notional Environmental Policy Act is expected to occur with the development of commercial deep seabed mining. An environmental assessment was conducted in order that testing and refinement of nodule waste disposal techniques can he completed prior to 1988, when commercial seabed mining can begin under U.S. legislation. Within this study three classes of process and four classes of waste disposal technique were identified, and five sites were selected as representative of first-generation nodule operations. Each realistic site/process/disposal technique combination was compared against potential effects to determine important characteristics of the rejects and the sites. Regulatory requirements were also considered at each site to identify important issues and their effect on the permitting process. Principal conclusions in the report are the following: (1) uncertainties exist in the regulatory regimes for hydrometallurgical process tailings, primarily regarding classification as hazardous waste; (2) slogs from nodule processing are expected to be inert and relatively easy to dispose of at all sites; and (3) additional physical and chemical information on properties of rejects from all processes is necessary to predict environmental effects.

Jan 1, 1982

By A. C. Munro

This paper, which describes the milling practice at the Britannia concentrator, Britannia Beach, B. C., is one of a series being prepared by the Bureau of Mines. The concentrator treats copper ore at the present rate of 6,000 to 7,000 tons of dry ore daily and produces copper concentrate and pyrite concentrate by selective flotation methods. The copper concentrate is smelted and the pyrite product is utilized for acid manufacture.

Jan 1, 1932

By Frederick H. Raab

A power-line proximity-warning (PLPW) system must have a high probability of detection (alarm activation at a specific distance), low probability of false alarm, and minimal set-up and maintenance. Tests of electric-field sensors have not demonstrated a dependable alarm distance. Alternative sensing methods such as microwave radar, optical radar, and sonar can meet the requirements by direct measurement of the range from the boom to the power line. Suitable microwave techniques include RF pulse, chirp FM/CW, and baseband pulse. Baseband-pulse radar has adequate range capability and does not require expensive microwave components. The radar cross section of a power-transmission cable is adequate for its detection optical-radar systems based upon LEDs and photodiodes are inexpensive, but can achieve only marginal performance in this application because of their limited modulation bandwidth. Since laser diodes and cryogenically cooled photosensors must be used to achieve the desired range resolution, the cost of an optical-radar system is greater than that of a microwave radar system. Sonar systems are feasible, but are not as precise and cost at least as much as baseband-pulse-radar systems. The performance of both optical-radar and sonar systems is degraded by dirt, necessitating the inclusion of a "windshield wiper.&apos; Baseband radar appears well suited to the PLPW application. The cost of a baseband-pulse radar PLPW system is expected to be comparable to that of an electric-field PLPW system. Development and testing of an experimental model are therefore recommended.

Jan 1, 1982

By S. Ralph Austin

Emanation coefficients of 950 samples of domestic uranium ore were successfully and rapidly determined with fair precision by modifications of the closed-can, gamma-only assay method, using commercially available or similar equipment. Coefficients range from <1 to 91 percent. Emanation varies considerably within each mine and area, but distinct differences among major mining areas were found, ranging from 7.5 percent for Moss Back Member, Chinle Formation, Southwest Lisbon Valley, Utah, to 56.6 percent for Ft. Union Formation (?), Powder River Basin, Wyoming. Coefficients also vary with (1) uranium mineralogy; (2) radium mineralogy; (3) lithology of host rocks; (4) grain size of uranium and radium minerals; (5) comminution of ore; (6) estimated porosity and permeability; (7) moisture content; (8) ore grade; (9) supposed mobility of deposits; age of deposits is unknown but limited by (10) age of host rocks which shows only doubtful correlation with emanation. Data obtained may be used to evaluate effects of investigated parameters on radon concentration in mines and thus to select efficient control measures. Drill-core emanation data allow estimates of probable radon problems in undeveloped deposits.

Jan 1, 1978

It is not uncommon to find large quantities of combustible materials in underground metal and non-metal mines. Support timber is the predominant combustible material. Spontaneous combustion, welding and cutting, shorted or overloaded electrical cables and careless smoking are common ignition sources. More recently, there is increased use of diesel mobile equipment that requires fuel storage and transfer areas. Diesel fuel spillage on hot engine manifolds and motors can result in rapid flame growth and heavy smoke accumulation in a matter of seconds. In-expensive, reliable fire detection and suppression systems are available to provide early warning of fire conditions and to isolate and extinguish fires that originate in fuel storage and transfer areas. This report presents an example of how technology developed and demonstrated under Bureau of Mines Contract H0242016, Mine Shaft Fire and Smoke Protection System, may be applied to protect underground diesel fuel storage and transfer areas. The area application described in this report is a representative example only; the fire protection described includes the concepts of ? Early warning and alarm ? Isolation ? Extinguishment ? Control

Jan 1, 2011

By E. G. Davis

The Bureau of Mines investigated gaseous direct reduction of low-grade iron ore concentrates in a continuous fluid-bed reactor. These studies were made in a 4-inch diameter fluid-bed reactor using hydrogen alone, and oxygen-or air-reformed natural gas as the reductants. The percent reduction is directly dependent on the mole ratio of hydrogen in the reducing gas to the oxygen associated with the iron oxide in the ore. Two-and three-stage fluid bed tests were simulated by repeated continuous tests. The results showed that percent reduction of the final product was dependent on the mole ratio of the quantity of hydrogen in the gas of each stage to oxygen in the iron oxide of the initial ore feed. Reduction as high as 87 percent in the single stages and as high as 94 percent in the multistages was obtained when either hydrogen or reformed natural gas was used as the reducing gas. Magnetic separation and concentration of the highly reduced fluid-bed product yielded a high metallic iron concentrate analyzing 85 percent total iron and 80 percent metallic iron with total iron recovery as great as 90 percent. Agglomeration of the high-grade metallized concentrate produced hard pellets analyzing 85 percent total iron and 78 percent metallic iron. Green pellets, with good strength, were made without any binder in a drum pelletizer. Direct melting of the high-metallic fluid-bed product in a basic lined arc furnace produced a nearly pure iron which contained 0.09 C and 0.01 P with 95 percent recovery of the metallic iron in the metal.

Jan 1, 1972

By Charles D. Wood

"Selected Topics,? in reviewing the control of emissions from diesel engine powered equipment used in underground mining, explores these fields of interest: hydrogen as fuel; lubricating oil as a source of particulates; applicability of stationary source scrubbers; worldwide diesel exhaust scrubbers; instrumentation technology for measurement of N02; control of emissions through application of sensors and microprocessors; use of fuel additives; technology transfer of marine diesel practice; technology required to use 4-stroke, aftercooled, turbocharged, direct injection engines; oxidation and reduction catalysts for diesel engine exhausts. "Selected Topics? makes recommendations for research and provides a bibliography and lists of references.

Jan 1, 1979

The following Inventory was prepared to provide mineral deposit data to the U.S. Army Corps of Engineers for use in the Resource Development Navigation Study in Alaska. The inventory was prepared using data contained in the U.S. Bureau of Mines Minerals Availability System (MAS) database. The Alaska portion of the database contains Information on over 7,000 mineral locations and deposits throughout the state. When MAS was established In 1975, database entries were originally compiled from literature searches by both Bureau personnel and contractors. Deposit data are obtained/maintained through Information gained from a variety of sources, Including published and unpublished Bureau of Mines reports, records, and files; U.S. Geological Survey (USGS) Bulletins, Professional Papers, and other reports; technical and professional Journals; State and other Federal agency publications; data generated during field examinations; and information obtained from knowledgeable individuals. Because of the size of the data base, many of the data have not been significantly modified since initial entry. Each deposit on the MAS data base has a sequence number of the following form:

Jan 1, 2011

By H. V. Makar

Laboratory tests were performed to obtain a quantitative description of the effectiveness of sodium sulfate (Na2SO4) for removing copper from molten iron and to determine the effectiveness of Na2SO4 on actual auto scrap. The tests were conducted on induction melted heats of iron averaging 0.58 and 1.50 percent initial copper and on cupola-melted auto scrap containing 0.45 percent initial copper. The Na2SO4 was added in powder form in amounts ranging from 2.9 to 43.8 percent of the weight of iron being treated. The data showed that copper removal for the various Na2SO4 treatments followed a similar trend, regardless of the iron composition that was tested. The equation Y = 1 - e-3.23x approximately reflects the relationship between copper removal and amount of Na2SO4 added, where Y is the fraction of copper removed and x is the ratio of the weight of Na2SO4 added to the weight of metal treated. Copper removals ranged from 3.3 to 74.5 percent and reductions down to less than 0.10 percent final copper were achieved in the auto scrap. Copper removals were generally accompanied by sulfur removal, and initial sulfur contents ranging from 0.10 to 0.20 percent were reduced to as low as 0.02 percent. High temperatures and long slag reaction times tended to induce copper and sulfur reversion from the slag, but, generally, the Na2SO4 treat¬ments were effective up to approximately 2,820° F with reaction times not exceeding 7 minutes.

Jan 1, 1968

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978

By Leonard Obert

This report describes a gage which, when used with my procedure for producing strain relief, will measure the resulting borehole deformation, From the borehole deformation the magnitude and direction of the principal stresses in a plane normal to the axis of the borehole can be calculated. The design considerations, mechanical construction, sensitivity, and stability of the gage are discussed. INTRODUCTION During the past two decades an increasing mount of consideration has been given to the problem of measuring and evaluating stress in rock around underground openings. Several investigators have made theoretical and model studies of the stress and (or) strain concentrations around simulated mine openings or in structural members, such as mine pillars or immediate roof. Other investigators have developed gages for directly or indirectly measuring stress or strain, and a number of reports present the results of measurements made with these gages. Because various methods and instruments have been developed, factors involved in this type of measurement will be briefly considered.

Jan 1, 1962

By John W. Taber

Discovery of these unusual fluorite deposits was brought to the attention of the Bureau of Mines late in 1951, shortly after the first locations were made. A brief investigation of the deposits by the Bureau revealed seven principal outcrops of fluorite in two areas. The smallest outcrop continuously exposes massive fluorite over an area 25 by 55 feet; the largest outcrop is a similar exposure 180 by 240 feet. The deposits appear to be sharp-walled, low-angle-, tabular ore bodies in granite and are at least 10 feet thick. The Bureau investigation of the deposits included bulldozer strip-trenching, drilling and blasting rock cuts, and channel sampling across three of the largest outcrops. This sampling indicated an average grade of 97.2 percent CaF2 and 1.44 percent SiO2. Preliminary metallurgical tests on the ore indicate that it can be concentrated to acid-grade specifications by simple gravity methods. One laboratory test recovered 78.4 percent of the fluorite in a product containing 98.7 percent CaF2, 0.25 percent SiO2, and 0.10 percent Fe2O3.

Jan 1, 1952

By Wilbur L. Webb

An electrically powered methane sampling system for application on mining machines was designed, fabricated and laboratory tested. The system will sequentially draw sample air at a controlled rate from up to three machine positions across the mine face and deliver the air to either an approved methane monitor, methanometer or flame safety lamp. The prime considerations in the design were to provide an intrinsically safe, water and dust resistant control box and an explosion-proof power box capable of being operated from the various mining power sources. The power box contains an internal battery that provides operating power prior to mining machine start-up and alter machine shut-down. The internal battery is recharged automatically when mining machine power is available.

Jan 1, 1977

By Forrest T. Moyer

To keep the mineral and allied industries informed of trend: in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and publishes, periodically health and safety statistics. This report includes data for 1961 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1963