Search Documents

By Christopher J. Pacitto

This paper presents a case history of an engineered, monitored, and tested program that provided an effective and satisfactory basis for the completion of pile foundations for Twin Dolphins 1 at La Peninsula Condominiums located in the Isles of Capri in southwest Florida, U.S.A. An 8-story building (withl-story parking underneath) along with recreational facilities (such as a swimming pool and tennis courts) had been planned for final construction. Following an evaluation of various foundation alternatives, a precast prestressed concrete (PPC) pile-supported system was selected. The building foundations were designed for pile capacities of 445kN (50 tons) and 890kN (100 tons) in compression and 133kN (15 tons) in uplift. A test pile program was performed to provide site-specific pile driving data, verify design assumptions, determine production pile lengths, and evaluate pile driving criteria. A total of 24, 356 mm (14-in.) square, 19.8 m (65 ft) PPC concrete piles were driven and dynamically load tested utilizing a Pile Driving Analyzer (PDA) within the building limits. Dynamic monitoring during probe pile installation and restriking was performed to estimate the ultimate capacity of the piles and to evaluate driving stresses during installation. CAPWAP analyses were preformed on PDA data to better estimate pile capacity, resistance distribution, and predict pile freeze (increase in pile resistance with time) and thus optimized the production pile lengths. Upon completion of probe pile installation, 12 of the probe piles were tested using the Pile Echo Tester (PET) function of the Pile Integrity Sonic Analyzer (PISA). PET testing was performed to evaluate the integrity of piles which had exhibited high driving stresses during PDA testing. Information gathered during the probe pile driving program was effectively utilized as part of the overall quality control program to install a total of 539 PPC piles (including 24 probe piles) within the building limits at the project site to depths ranging from 9.1 to 19.8 m (30 to 65 ft) below the existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the CAPWAP analysis for probe piles. Use of geotechnical instrumentation and PDA assisted technology enabled each foundation support element to be constructed to its optimum capacity and at optimum cost. Furthermore, by using PDA the consultant was able to quantify a difficult to measure geotechnical phenomenon termed "pile freeze" which eliminated costly overdriving and unnecessary splicing of piles.

Jan 1, 2002

By D. R. Dance

The Resonant, or as it has more commonly come to be known the 'Sonic' Pile Driver, dates back to the early 1960's, when prototypes were produced by Charlie Guild, of Providence, Rhode Island, and A1 Bodine of Los Angeles, California, these were later to be developed into the unit known as the BRD 1000. Based on this initial work, the Shell Oil Companies of Sonico and The Resonant Pile Corporation, produced and operated 30 of these BRD 1000 machines, which were used throughout the U.S.A. and Canada on a wide range of foundation projects. Subsequent to this, Raymond International and G K N, of England, operated units on programs; the G K N units being of slightly modified configuration. In 1973 Hawker Siddeley Canada Ltd., acquired the license for the Pile Driver and related systems with the intent of promoting the use of the machines to install support pilings on the Alyaska Pipeline Project, but this did not materialize due to problems with the oscillator. After radical redesign and field testing of the oscillator system the unit was employed on a number of test projects principally in Northern Canada and Alaska.

Jan 1, 1987

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2005

By Paul J. Axtell

The design-build delivery system is being used to erect the landmark Christopher Bond Bridge as part of the kcICON project. The cable-stayed bridge is currently under construction and will span the Missouri River on I-29/35 in Kansas City, Missouri. The design-build process for the foundation work on this project has been successfully implemented as a result of cooperative efforts between the foundation designers and the constructors to develop a constructible design.

Jan 1, 2009

By Lois G. Schwarz

I did a project (Sungai Piah) as a consultant to your firm in Malaysia, where we were faced with a similar situation as sketched out in your question. The following is what we did for the grouting of the primary holes, which were both located upstream of the plug as well as downstream: We used a hydrophobic MDI based semi-rigid polyurethane prepolymer in the first phase of the grouting operation when grouting under water flow conditions. Then in the second phase and also for the contact grouting we used a two component water compatible polyurethane elastomer. And then for deeper formation grouting, when all the water flow had been stemmed in the vicinity of the plug, we used a regular (balanced stable) cement based grout. So it may not exactly answer your question, but we first used hydrophobic grout because it is very efficient to grout a formation through which water flows. We didn't stop all the leaks day-lighting downstream of the plug or all water running through the formation near the plug, but the flow of water through the rock formation adjacent to the plug was reduced by 99.9%, after completing the urethane grouting. This facilitated the placement of cement based suspension grouts without wash-out.

Feb 10, 2003

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2013

By Ray. K. Filip

The concept of installing a steel sheet pile retaining wall into the ground by "pressing" has resulted in the development of various equipment solutions over the last thirty years e.g. Taylor Woodrow ?Pile Master', Giken 'Silent Piler" & Tosa 'Still Worker?. Dawson Construction Plant Ltd (DCP), have recently advanced the pile pressing concept with the introduction of their 'Push-Pull' system. This advancement offers significant improvements in the quality of installation compared with traditional pressing solutions but also greater versatility, higher productivity and, most importantly, generates new opportunities through a wider range of applications for "silent piling'. This paper will focus primarily on the use of the Push-Pull concept in the construction of a unique "integral" bridge in Milton Keynes, England. Finally, the paper touches on the development of quiet, vibration-less pile extraction equipment, which allows steel to be considered the foundation material of choice for truly sustainable construction. It is no longer acceptable to leave unwanted piles in the ground.

Jan 1, 2006

By Susheel R. Kolwalkar

A significant increase in the side shear capacity over a period of time is often observed in case of driven piles. This phenomenon is referred to as ?setup? or ?freeze?. This phenomenon cannot be predicted based on the knowledge of the engineering properties of soil. Different kinds of mechanisms have been proposed in order to explain set-up in cohesive soils. In engineering practice, set-up is incorporated in design on the basis of empirical formulae and depends to a large extent on personal experience and judgment of the design engineer. Set-up is a natural process which cannot be accelerated by any existing practice. A research was initiated to investigate the mechanism of pile set-up in clayey soils and explore the possibility of accelerating the set-up process by an electro-kinetic method. The system chosen for the present study consists of a prototype steel pile driven in kaolinite clay. A laboratory test program was developed at Cleveland State University in order to meet the goals of the proposed research. Results obtained from these tests are very encouraging and show pile capacity increase of 200% within the first 5 days of electric gradient application versus those that experience natural set-up. In this paper, theoretical considerations and laboratory test results are presented and discussed.

Jan 1, 2008

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By Wojciech Szczepiński, Dominik Gächter

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Oct 1, 2021

By Dominik Gächter, Wojciech Szczepiñski

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Sep 8, 2021

By Richard W. Hanford

The geotechnical construction industry generally considers soil mixing to be defined as an in situ ground improvement or treatment method by which a dry or wet reagent is introduced into the ground and is blended with the soil by mechanical or rotary mixing tools. This results in relatively homogenous mixtures whose engineering properties are improved and are greater than the soil properties before mixing. Reagents usually include cement, but may also include processed clay such as bentonite, when a reduction in hydraulic conductivity is desired, or other proprietary chemicals when chemical stabilization is the objective. Mixing may be either shallow or deep. Shallow Mixing is the term arbitrarily used for treatment of soils within the upper 30 feet; Deep Mixing denotes treatment below 30 feet to the depth limits of the equipment. Mixing equipment may consist of single or multiple-shaft tools having cutting and mixing blades of many different configurations. To avoid using proprietary nomenclature, reference to Shallow Mixing Methods (SMM) and Deep Mixing Methods (DMM) are the preferred terms. Although originally developed and patented in the United States in 1956, in situ construction using various soil mixing methods is more prevalent in Japan and the Scandinavian countries. Reintroduced into the United States from Japan in 1986 for ground improvement and liquefaction mitigation at Jackson Lake Dam, Wyoming, acceptance of soil mixing methods has been gradual but slow. Applications typically include:

Jan 1, 2001

By Vidyaranya Bandi, Madhav Madhira, Kota Vijay Kiran

"Using hyperbolic relationships for the non-linear responses of shaft and base resistances, a method is proposed for estimating initial shaft and base stiffnesses and ultimate shaft and base resistances of a pile from pile load test results. An iterative procedure is used to arrive at the values of shaft-soil and base stiffnesses and the ultimate shaft and base resistances. The method is applied to load - displacement data available from pile load test results to illustrate its efficacy.INTRODUCTIONA pile foundation is the most effective and economical solution in transferring large vertical loads to deeper depths. As the pile is subjected to axial load, the soil mass surrounding the pile is vital in providing vertical support for the pile. The nature of pile–soil interaction is three dimensional and to complicate the problem further, response of soil is nonlinear. Finding a closed form solution to such problem is extremely difficult. Several methods were developed to study and predict the response of the composite pile–soil system. Faruque and Desai (1982) implemented both numerical and geometric non-linearities in their three dimensional finite element model. Rajashree and Sitharam (2001) developed a nonlinear finite element model of batter piles under lateral loading using a hyperbolic relation for static load condition and modified hyperbolic relation, including degradation and gap for cyclic load condition.The ultimate capacity of the pile is estimated considering the strengths and unit weights of soil layers with depth, overburden pressure and other relevant parameters. The estimated capacities always need to be validated by conducting initial maintained load test. The estimated capacity may differ with the actual at site since the values of strength, stiffness, interface resistance between pile and soil, lateral earth pressure coefficient with depth and soil stratification, etc., differ from the design parameters considered for estimating the ultimate capacity of pile. The estimation of axial capacity of piles involves considerable uncertainties in selection of appropriate design parameters and the design rules are not always consistent with the installation procedures/processes involved."

Jan 1, 2017

By John P. Turner

The behavior of tieback retaining walls depends on many factors, including soil properties, groundwater conditions, construction sequence, spacing and stiffness of tiebacks and soldier piles, tieback loads, and others. The primary design considerations for tieback walls are 1) adequate stability and 2) limiting wall movements. Traditional design methods rely on apparent earth pressure diagrams and experience to predict the forces which must be supported by the tiebacks to provide adequate stability. The required soil properties depend upon whether the soil is sand, soft clay, or stiff clay. Design to limit wall movements is more difficult and the usual approach is to design the wall with an adequate factor of safety for stability and then evaluate wall movements during construction through the use of load tests on individual tiebacks and monitoring of wall movements by optical surveying, slope indicators, and extensometers. If excessive movements are likely to occur, it is often not known until construction is well underway. This approach is reflected in the fact that few tieback walls fail due to a lack of adequate stability, while most litigation involving tieback wall performance is related to excessive movements. Much progress has been made in recent years in methods for predicting the movement of all types of insitu retaining walls (Clough et al. 1989, Clough and O'Rourke 1990). These methods are based upon both experience and analytical methods. This paper reviews the methods currently available for evaluating both the stability and movements of tieback retaining walls. Case histories involving excavations constructed in the downtown Seattle area are used to evaluate the applicability of the available methods to Seattle conditions and to illustrate the importance of soil behavior in tieback wall performance.

Jan 1, 1990

By Gregory J. Canivan

Three test pile programs were conducted in Charleston, South Carolina to evaluate differences in bearing resistance due to installation methods. The tested piles were installed with impact hammers and vibratory drivers through soft clays and/or loose sands into the Cooper Marl, a stiff calcareous marine clay or silt. Piles driven into the Cooper Marl experience significant capacity gain with time following initial installation due largely to pore pressure dissipation. Pile size and pile type were both known to affect pore pressure generation during installation and subsequently the capacity gain with time. The test programs were primarily conducted to optimize pile design values and construction methods with regard to trestle construction but the results also contribute to the understanding of driven pile behavior. High strain dynamic testing was performed on several open-end pipe and H-piles. The measured difference in long-term bearing capacity of the H-piles as a result of the two installation methods was negligible, while the short-term bearing capacity of the pipe pile was larger when the piles were installed using impact hammers. The lower short-term resistance in the vibratory driven piles is attributed to larger excess pore pressures generated during installation compared to those generated during impact driving.

Jan 1, 2002

By Maurizio Siepi, Fabio Santillan, Lyndon Bedford, Carlo Crippa

"Abstract: Wolf Creek dam, on the Cumberland River in Kentucky, US, operated and maintained by the Nashville District of the USACE, is the Corps' largest reservoir east of the Mississippi river. The 1748 m (5,736 ft) long Wolf Creek dam combines earthfill and concrete gravity sections. Construction began in 1941 and was completed in 1950. The dam showed signs of instability in the 1960’s, and in the late 70’s an in-depth project of rehabilitation was undertaken, using both grouting and secant piles. The works saved the dam, but in the late 90’s further signs of distress worried the Nashville district of USACE which, after a study conducted on the water seepage, concluded that construction of a new concrete barrier cut-off wall was needed. In 2009, the $341.4 USD million contract was awarded to TREVIICOS-SOLETANCHE JV.The new wall, located upstream of the concrete monoliths, has a minimum thickness of 60 cm (24 in.), and runs the length of the embankment, into the right abutment, for about 4,200 feet. The founding depth reaches 84 m (275 feet), well below the zone of solutioning. With a total surface approaching 92,903 sq.m (1,000,000 sq.ft), the Wolf Creek barrier wall is unlike any other project in the world.The construction of the cut-off wall followed a complicated but logical sequence of several operations, involving a variety of technologies: grouting, hydromill, directional drilling, and secant piles with reverse circulation. The intensive rock grouting program was aimed to minimize the risk of slurry loss and extend the positive cut-off further deep. Subsequently, an Encasement Concrete wall was installed with hydromill, toeing into the rock, to protect the embankment during the following phases. Smart holes were then drilled into the Encasement wall down to the final depth. Eventually, the holes were used to install the secant piles by employing the reverse circulation piling method.An extensive verification campaign has confirmed the superior quality of the cutoff wall consisting of 1200 secant piles, exceeding by far USACE’s requirements. The main project was substantially completed in early 2013. A small portion of secant piles wall will be installed downstream of the dam, to close the switchyard, finishing the project in the early months of 2014.IntroductionWolf Creek Dam is located on the Cumberland River in south-central Kentucky. The Nashville District of USACE operates this multipurpose dam to provide hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. Lake Cumberland, created by the dam, impounds 7,400 million cu.m (6 million acre foot) at its maximum pool elevation of 232 m (760 ft) above sea level. This lake is the largest reservoir east of the Mississippi and the ninth largest in the United States, and attracts 4.89 million visitors, more than Yellowstone National Park (2.87 million).This paper describes the recently completed works for the rehabilitation of the dam, accomplished by TreviICOS-Soletanche JV with the construction of a new Barrier Wall."

Jan 1, 2014

By Donald A. Bruce

The paper reviews aspects of the construction and performance of prestressed ground anchors installed in soils and weak rocks. Attention is focused on good practice for drilling, tendon fabrication and handling, grouting, stressing and testing. Regional variations - not always logically justified - are described. The performance of anchors in a variety of geological conditions is illustrated with reference to recent full scale test programs. 1. Introduction In the United States there has been steady growth in the use of prestressed anchors in materials other than competent or hard rock, in the years since their introduction in the late 1960's. This expansion has to a large extent been driven by specialty geotechnical contractors who both imported foreign developments and conducted their own basic researches, in locally prevailing conditions. With such data and experience, these engineers have had the confidence to promote "alternative solutions" for difficult earth support problems to receptive designers and owners. In turn, being engaged in the details of design and performance monitoring has given these parties the close exposure necessary for the real transfer and understanding of the technological concepts, and this knowledge has generated positive feedback for the contractors.

Jan 1, 1991

By Garland E. Likins

High-strain dynamic testing of drilled shafts and cast-in-place piles has become routine procedure in many parts of the world today. Field testing is performed by measuring strain and acceleration records under impact of a falling mass. Wave equation analysis is utilized to design the weight, drop height and cushion of the hammer apparatus to assure a successful test. The Pile Driving Analyzer* (PDA) and CAPWAP* methods are used for data acquisition and analysis. Testing results yield information regarding pile static bearing capacity, structural integrity, and pile-soil load transfer and pile load-movement relationships. This paper discusses application of high-strain dynamic testing to cast-in-place shafts with emphasis on aspects unique to this type of pile. Suggestions regarding minimum requirements for good quality tests are offered. Five case histories reported in the literature are summarized and a sample specification is also included.

Jan 1, 1995

By Larry Rayburn

Design of cost effective engineered solutions to complex problems requires the team efforts of the owner, the designer and the specialty construction contractor. The basic ingredients of success required to remain competitive and still produce a quality product are creative design based on experience and sound engineering principles, plus practical aspects of constructibility. The three case histories describe creative design/construct approaches that benefited all parties. 1. Introduction The increasing demand placed on specialty contractors to provide cost effective buildable solutions to complex construction problems compels us in the industry to be highly innovative. The practice of geotechnical engineering is considered more of an "art" than perhaps the other disciplines within civil engineering largely because of the basic nature and variability of soil and rock. The geotechnical design engineer must have the knowledge of the components of his design and know the limitations of his equipment and labor force. Thus, for the design/build specialty contractor the potential for creation of unusual solutions to difficult problems is quite high.

Jan 1, 1991