Search Documents

By T Hughes

Upward pressure on all mining operations is coming from the triple bottom line. To some extent this is being offset by the rise in mineral prices, but this may or may not continue. The other serious issue facing all companies is the replacement of economic reserves as exploration levels over the past decade continued to decline in line with falling mineral prices. In order to underpin the sustainability of the mining industry it is necessary to continue to reduce cost, reduce the mine environmental footprint, whilst increasing community benefit. At the same time it is imperative that we increase the economic reserves. The highest risk is in adding new mineral discoveries as the strike rate for economic discovery decreases. Gekko Systems Pty Ltd recognises that the most simple and risk averse route to increasing economic reserves is to reduce cut-off grade in the mine, thereby bringing formerly uneconomic reserves into the economic category. We have been developing a new process flow sheet which embodies the triple bottom line and the issue of economic replacement of reserves. This paper describes this flow sheet and presents four examples where this concept is/can be applied to bring about triple bottom line benefits. Sustainability can only be assured if we are the ones in control of our environment, costs and reserves.

Jan 1, 2007

It is shown that factors associated with conditions whIch are thermodynamically favourable for the formation of CuS04 in roasting lead to high copper recoveries on leaching. One of these factors is the ratio of the air to solids used for roasting. This can be varied widely without loss of temperature control in the sulphating roasting of many Australian copper concentrates.Thus, the prediction of the air to solids ratio corresponding to a maximum p(SO3) value, for a given concentrate and temperature, is of importance in fluidized bed roasting, since this could be associated with the formation of a maximum quantity of CuS04. Calculations are presented which predict this air to solids ratio, not only for a given concentrate composition, temperature, and pressure, but also for air which is enriched with sulphur dioxide or oxygen.

Jan 1, 1968

Particle Size Measurement of TiO2 Nanoparticles in Non-Aqueous Solvent by Interactive Force Apparatus Under an Electric Field

Sep 13, 2010

By M D. Hannington

On the southern flank ofLihir Island, a group of three volcanic cones were discovered at water depths from 1000 - 1500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts, and porphyritic phlogopite basalts. One of the volcanoes has a recently erupted ejecta blanket (recovery of warm ash!), containing a suite of abundant mafic to ultramafic xenoliths. These xenoliths appear to represent a unique cross-section of subduction-modified mantle material sampled by volatile-rich primary fore-arc magma during its ascent to the seafloor. The most spectacular finding was the discovery of an active hydrothermal system with associated vent fauna and mineralization at Edison Seamount, and the recovery of unusually gold-rich (up to 43 ppm Au) hydrothermal precipitates in 1050 m water depth at the top of Conical Seamount, only 25 km south of the world-class epithermal Ladolam gold deposit on Lihir. The discovery of submarine hydrothermal vents associated with highly alkaline, quartz-undersaturated fore-arc volcanics represents a significant departure from similar hydrothermal systems on the mid-ocean ridges and in back-arc basins. The high gold grades in hydrothermal precipitates at Conical Seamount may indicate the first documented example of a shallow-marine epithermal system analogous to those known on land, and has important implications' for the gold potential of submarine arc environments.

Jan 1, 1995

By A D. Campbell

Conversion of Mineral Resources to Ore Reserves requires a multidisciplinary approach and application of a number of Modifying Factors. The Modifying Factors for mining, particularly dilution and recovery in a caving mine are complex and can be difficult to determine. Cave flow modelling software is widely used for mine planning, scheduling and forecasting metal production. However, the conversion of Mineral Resources to Ore Reserves remains a difficult and subjective process and a consistent approach to convert Mineral Resources to Ore Reserves as part of the cave flow modelling process is not published in the literature. This is due to the difficulty in estimating the Ore Reserve that remains as cave stocks at a particular point in the mine schedule, the recovered tonnage and grade of the diluting material at various stages in the mine life, as well as the Mineral Resource classification of both the recovered and diluting material that forms the Ore Reserve. The key principle of this paper is the tracking of the Mineral Resource classification in the flow model used to estimate the Ore Reserves. This is critical to defining the Ore Reserve as Proved or Probable and enabling transparency in the reporting process. An approach for dealing with mineralised external dilution in the Ore Reserve estimation process is also provided.This paper outlines the approach to convert Mineral Resources into Ore Reserves developed at the Ernest Henry mine sublevel cave (EHM SLC). The same method could be used in any cave mine and applied at any stage of the mine life. The process replaces broad-brush assumptions for the mining Modifying Factors, such as dilution and recovery, as these are determined numerically as part of the model computation. This paper explains the Ore Reserve estimation method with a worked example to enable the reader to adopt the process at any caving mine. Mineral Resource classification within the block model is embedded in the cave flow model and the flow model results used to attribute tonnes, grade and the mixed proportions of the Mineral Resource classification for material extracted from each drawpoint. This information is then used to convert planned mine production into the appropriate Ore Reserve classification. Since the flow model simulation follows the mine schedule, it can be used to predict depletion and cave stocks at any stage of the mine life, and can calculate a residual block model at the end of the mine life. The accuracy of the flow model is checked by validating the forecast ore grade and metal tonne with reconciliation data from the concentrator which is also used to calibrate the flow model.CITATION:Campbell, A D, 2017. A simple and accurate method for Ore Reserve estimation and Mineral Resource depletion in caving mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

Dynamics of Three Phase Contact Line Motion in Liquid-Liquid-Solid Systems - Impact of Surface Roughness

Sep 13, 2010

Geological maps, data, and prospectivity analysis relevant to mineral exploration in New Zealand have recently been released. Regional-scale geological mapping is increasingly available for the country through the QMAP 1:250 000 Geological Map of New Zealand programme. Published QMAP sheets Greymouth, Wakatipu, Waitaki and Dunedin cover large areas of interest for mineral exploration companies. The QMAP geological data are also available in digital form for use with other digital datasets using GIS software. Crown Minerals, in cooperation with GNS, have completed two gold prospectivity studies; the first covering mesothermal gold in the South Island, and the second encompassing epithermal gold in northern New Zealand. These studies have defined areas of interest for these two mineralisation types and assembled geological, mineral occurrence and production, geochemical, geophysical, topographic and cultural data into projects for use with GIS software. Included are the results of prospectivity modeling for gold using these data and specific mineralisation models. The prospectivity studies and relevant data are freely available on CD through Crown Minerals and are intended to encourage mineral exploration in New Zealand.

Jan 1, 2003

THE Broken Hill mining field, approximately 31 miles in length, is at present being exploited by seven companies, viz. : North Broken Hill Limited, Junction North Broken Hill No Liability, Broken Hill Proprietary Block 14 Company, Broken Hill ProprietaryCompany Limited, Sulphide Corporation Limited, Broken Hill South Limited, and Zinc Corporation Limited.The variation in size and shape of the ore-bodies in the mines of these companies, together with the many alterations in pitch and dip, necessitates differences in methods of mining, each company working out its problem in its own particular way.In the matter of chute construction for the handling of the ore broken in the stopes, each mine belonging to the above companies has adopted a style particularly its own, though it may be said that one or two of the types approximate very closely to each other, slight minor differences only being noticed in the design. It is the purpose of this paper to give a brief description of the principal types of chutes now in use in th,e various mines on the field, and in doing so they may roughly be classified into three groups, viz:1. Bulk Chutes, 2. Circular Chutes, 3. Square-set Chutes.The Bulk type of chute is used in the North and British mines of the North Broken Hill Limited, the Central and Junction mines of the Sulphide Corporation, the South Blocks mine of the Zinc Corporation, and the Block 14 mine.The Circular type of chute is used by the Broken Hill South mine and the South Blocks mine.The Square-set chute is used in the Proprietary mine, the Junction North mine, and occasionally in other mines where the square set method of mining is a necessity, and more particularly as mullock passes.

Jan 1, 1925

This technical note describes a problem with WANG82, a ventilation network analysis programme. The problem was highlighted by Renison Ltd when using the programme on large, complex networks. Under certain circumstances the programme produced incorrect results or failed to converge to a solution.

Jan 1, 1986

By L Hussey, H Thanasekaran, J Kohmuench

Conventional flotation technology has historically failed to achieve high recoveries when treating <15 µm particles (Lynch et al, 1981). The new StackCell™ flotation technology was developed to specifically target this particle size range, and was tested at pilot plant scale at Mt Keith Nickel Concentrator. The streams tested, Slimes Rougher Tailings and Fines/Slimes Cleaner Tailings, represent 21% and 11% of the total nickel lost to tailings in the plant. Laboratory scale test work indicated that an economically significant fraction of these losses was consistently available to be recovered by additional flotation. The pilot plant experimental scope included over 50 tests. A grade recovery curve for each stream was developed, as well as information on the effect of ore type, feed rate, wash water, air flow, collector and frother on the performance of the cell. The single StackCell was able to achieve nickel recoveries of 16.8% and 16.5% on the Rougher Tailings and Cleaner Tailings, respectively, at grades consistent with these blocks. Additional test work of the StackCell in a cleaner scalper duty yielded final quality concentrate with a maximum nickel recovery of 59.5% for the single stage StackCell. Laboratory scale simulation of the downstream impacts of the StackCell operating as a cleaner scalper indicated a net recovery benefit of up to 2.0% for this cleaner block.Tests were completed to compare residence time requirements of the StackCell, as compared to conventional flotation. In 55 seconds, the pilot plant StackCell achieved 50% of the recovery of a 960 second laboratory scale conventional flotation on the same feed material. The apparent improvement in flotation kinetics is attributed to the novel high intensity aeration system, which provides efficient bubble-particle contact thereby shortening the residence time required to achieve high recoveries. The smaller footprint and lower energy costs of such a cell are also benefits of this technology, which is being considered for industrial scale installation as a result of this test work. Given the industry’s historical poor performance treating slimes with conventional flotation, it is clearly best practice to challenge the status quo through innovative new technology, such as the StackCell.CITATION:Hussey, L, Thanasekaran, H and Kohmuench, J, 2017. The application of high intensity flotation technology at Mt Keith nickel concentrator, in Proceedings MetPlant 2017, pp 259–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

The principal source of funding the working capital requirements of gold miners has traditionally been equity. However in the 1980s, with a substantial increase in activity in the exploration for, and the production of, gold the traditional sources of equity finance became no longer sufficient to meet demand. With the often high cost of raising equity, the need for developing alternative financing structures became critical, especially since the stockmarket crash of 1987 which at least until recently, adversely affected the amount of equity capital available for investment in mining.

Jan 1, 1994

Identifying Opportunities to Reduce the Consumption of Energy Across Mineral Processing Plants

Sep 13, 2010

Remediation of Mine Seepage at Batu Hijau

Sep 13, 2010

The following paper on the development of processes for the treatment of crude ore, accumulated dumps of tailing and slime at Broken Hill, has been prepared by a committee of the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy, with the object of recording, in chronological order, the developments of the various processes which have led up to the metallurgical practice of the present day.

Jan 1, 1930

By D Brett

"Mine waste storages including tailings dams and waste rock dumps represent arguably the biggest risk on a mine site from both physical and geochemical viewpoints, related firstly to structural stability and the consequences of failure and secondly from potential on-going seepage or run-off of acid and metalliferous drainage (AMD). The risks are most likely to increase during operations and continue through the closure and post-closure phases, with the waste storages likely to be the most difficult features to resolve in the mine closure process. Contaminated water quality from tailings dams and waste rock dumps can require treatment "in perpetuity" at a cost of hundreds of millions of dollars. The problem is increasing with ever larger mine operations and waste generation volumes. This paper identifies leading practice methodologies in planning and operating mines and process plants to minimise the risks from tailings storages and how this might also affect waste rock management and even the design of mine excavations. These methodologies require a "big-picture" approach to develop an understanding of the overall issues and identify synergies between the different operational areas on a mine site that can reduce overall risk. With a conservative approach and realistic allowance for future costs it is possible to facilitate decisions at the mine planning stage that can reduce risk and save cost over the long term. This is in contrast to the common approach where each operational area is looking to minimise its own costs with a short-term view. Incorrect mine methodologies can be developed by allowing net present value (NPV) accounting methods to trivialise future closure issues.Methodologies discussed include: Integrated Waste Management - Significant structural improvements to tailings dams can be achieved if the structures can be incorporated into the waste rock dumps. Risk of AMD can also be reduced by utilising the tailings and waste rock effectively. This could go even further to consider the placement of wastes to limit mine void environmental issues; Process Optimisation - Water quality and the nature of potential tailings dam structures can be highly influenced by the geo-chemistry of the tailings. This can be modified by processing, where simple changes such as maintaining separate streams of geo-chemically different tailings rather than recombining them or by initiating further processing to remove problematic minerals such as sulphides; Enhancing Geophysical Properties - The geochemical performance of waste repositories can be greatly influenced by the geophysical properties of the stored materials, particularly the air-water characteristics, which are influenced by particle size, density and permeability. The geotechnical properties can be enhanced by strategic paddock dumping, blending and compaction.These methodologies are demonstrated by case histories.CITATION:Brett, D, 2013. Mine waste risk minimisation by integrated waste management and process optimisation, in Proceedings MetPlant 2013, pp 247-258 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

Results of flotation tests on lead-zinc ore from Broken Hill, N.S.W., confirmed that flotation at pH 9 in the presence of cement gave poorer metallurgical results than flotation at pH 7. Additions of 2 kg/tonne wood raspings [e.g. blackbutt (Eucalyptus pilularis), blue gum (E. saligna), brushbox (Tristania conferta), or turpentine gum (Syncarpia laurifolia)l had little effect at pH 7 but greatly accentuated the deleterious effect of cement at pH 9. This was shown to be caused by e:xtractives (e.g. polyphenols and carbohydrate materials) derived from woods at pH 9. The proportion of extractives, as shown by DV absorbance spectra, increased with increase of pH and was affected by various salts.Additions of 1 kg/tonne Al2(S04)3.16H20 when cement or cement and wood were present showed that metallurgical results obtained by flotation were then very simHar to those in the absence of cement or wood or both. This was ascribed to lower pH values in the presence of aluminium sulphate and possibly to specific chemical effects.Additions of aluminium sulphate appear to offer an economic solution to the problem of treatment of ores contaminated with cemented fill at Broken Hill.

Jan 1, 1974

Gold was determined directly in eight different mill cyanide solutions, by atomic absorption spectroscopy in an acetylene-air flame. Some of the mill solutions were diluted with water to bring them into the most sensitive absorption region (5-50 p.p.m. Au) whereas those solutions with very low gold content «2 p.p.m.) were concentrated by evaporation.Calcium was complexed with ethylene diamine tetra-acetic acid (EDTA) to avoid the undesirable effect of a precipitate on atomization.When added to standard gold solutions, EDTA had no effect on absorption, nor did any of the impurities common in mill cyanide solutions.Known amounts of gold, ranging from 2 to 30 p.p.m., were added to mill solution'aliquots and recovered to within 100 ± 2·5 per cent. For duplicate determinations under normal worKing conditions, standard deviation was 1·32 p.p.m.Excellent agreement was found between atomic absorption gold values and accurate fire assay values.INTRODUCTIONAtomic absorption spectroscopy has been shown to offer a rapid and accurate method for the determination of trace amounts of a number of metal ions. In the field of primary metallurgy atomic adsorption has been used for routine determinations of lead, copper, silver, zinc, cadmium and iron in a variety of raw materials and intermediate products.The scope of atomic absorption spectroscopy was reviewed recently by Willis (1963).The noble metals silver, gold, platinum, rhodium and palladium were determined by atomic absorption from chloride solutions by Lockyer ·and Hames (1959). In their determination of gold down to 1 p.p.m., they found no interference from the noble metals, nor from considerable excess...

Jan 1, 1964

Performance of Outotec FloatForce« Flotation Mechanism - A Study in Both Computational Fluid Dynamics and Industrial Scale Measurement

Sep 13, 2010

WHILE in the employ of the Broken Hill Associated Smelters and the Electrolytic Zinc Oompanies at their South Melbourne Research Station, the writer was detailed to investigate the principles underlying the Parkes Process with a view of determining:1. The Interdependence of the variables:(a) Quantity of zinc required per charge,(b) Temperature of stirring of each zincing,(c) Silver content of the bullion after first zinculg,(d) Silver content of the bullion after second zincing,(e) Silver grade of the crusts produced for retorting, with reference to the method of working the Parkes Process then in operation at Port Pirie.2. The possibility of effecting improvements in the Port Pirie practice of desilverising, especially with respect to:(a) Silver grade of the crusts produced for retorting.(b) Quantity of zinc required per charge.The method of desilverising in practice at Port Pirie was a two-stage zincing.In both zincings the bullion was cooled to its solidification temperature and the silver crusts which separated from the lead were completely removed.The crusts from the first zincing were retorted, and the crusts from the second zincing were returned to the first zincing of the next charge.

Jan 1, 1925

The Application of Roasting Pretreatment for Antimonial Refractory Gold and Silver Ores

Sep 13, 2010