Search Documents

By N. J. Grant, D. Carne, J. B. Seabrook

IT is unnecessary to review much of the literature on hydrogen embrittlement of steel since several excellent reviews and bibliographies exist.1-3 Hot acid pickling and cathodic charging have been known to cause hydrogen embrittlement of steel and have been used as laboratory methods to charge steels with hydrogen.4-8 Experimental Procedure The problem of prime concern in all instances, except in the work of Sims and coworkers,10 is that at no time was there a definite known hydrogen value reported which could be related to a particular value of the degree of embrittlement. It was the purpose of this research to determine the relationship between hydrogen content and degree of em-brittlement quantitatively. The 1020 stock used for the specimens was hot-rolled 7/16 in. diam rod of the following analysis: 0.19 pct C, 0.40 pct Mn, 0.012 pct P, 0.036 pct S' Vacuum-fusion analyses for nitrogen and oxygen gave 0.014 pct O2 and 0.0011 pct N2. Cathodic charging was used to cause embrittle-ment. The advantages of this method were that no quenching was necessary, the impregnation was reasonably controllable, and representative samples for analysis could be prepared simultaneously with the charging of the tensile bars. Analyses for hydrogen were made in a vacuum-fusion type of apparatus which extracted gas from the samples by fusion in a molten tin-iron bath' This apparatus, which has recently been described in detail elsewhere, will not be discussed here.". " Consecutive samples can be analyzed every 15 min with an accuracy of 0'03 ppm. A A from an electrolytic or pickling bath can be charged for analysis in about 3 min, and analysis completed in 15 min. Samples of as-received 1020 stock were analyzed and found to contain a negligible amount of hydrogen (0.06 ppm). Preliminary pickling and electrolytic charging gave highly variable results. Cold-worked samples showed higher values but ranged from 0.6 to 6.0 ppm of hydrogen. Charging at 90°C gave higher values of charged hydrogen, but troublesome films on many of the specimens resulted. It was not until a few drops of a catalytic poison, prepared from 2 g of yellow phosphorus dissolved in 40 ml of carbon disulphide,8 was added to the electrolytic cell that fairly consistent high values of hydrogen could be charged into the as-received 1020 steel at room temperature. The cell used is sketched in fig. 1. The anode and fixture for the tensile specimens were fastened to the cell cover as shown, and the specimen was screwed in place, centrally located with respect to the anode. At first, anodes of lead and graphite were tried, but they contaminated the electrolyte and gave a slight deposit on the specimen. Later, a platinum wire was used in the form of a uniform helix. A current of 2 amp, corresponding to about 0.5 amp per sq in. of cathode, was used for most specimens. The electrolyte was 4 pct H2SO4 solution. Fig. 1 shows the form of the special tensile bar, the main portion of which was an ordinary 1/4 in. diam, 1 in. gauge length test bar, except that two to four small cylinders of stock were left attached by small links to the bottom end of the tensile bar for the purpose of providing samples for hydrogen analysis. Thus the bars and samples were charged with hydrogen simultaneously and an analysis could be made while the bar was being tested mechanically. Experiments were performed to determine how representative the test cylinders were of the middle of the test bar proper. While the bar center was being analyzed, the small cylinder was stored in dry ice, since it had been shown that such storage prevents loss of hydrogen for many hours.12 The results of these checks are shown in table 1. The checks are very good (0.3 ppm) and indicate that it is permissible to use the small end cylinders to establish the hydrogen content of the tensile test bar proper-

Jan 1, 1951

By E. T. Turkdogan, W. L. Worrell

The rate of reaction of hydrogen sulfide with ferrous sulfide was studied by measuring the initial rates of sulfidation of iron strips in hydrogen sulfide-hydrogen-argon mixtures at 670°, 800°, and 900" C. The time-dependent surface sulfur activity is derived from the instantaneous rate of sulfidation with the assumption that diffusion in the sulfide layer is in a pseudo-steady state with the gas-sulfide chemical reaction. The rate of sulfur transfer from hydrogen sulfide to the surface of iron sulfide is proportional to the partial pressure of hydrogen sulfide and inversely proportional to the activity of sulfur at the surface of the sulfide layer. The derived rate equation is based on the assumption that most of the surface sites on the chemisorbed layer of iron sulfide are occupied by sulfur atoms and that the slow rate-controlling reaction is the dissociation of hydrogen sulfide on the chemisorbed layer. The experimental results are in reasonable accord with this reaction model. 1 HE slow approach to parabolic growth rate in the sulfidation of iron in hydrogen sulfide-hydrogen mixtures is a manifestation of slow approach to surface equilibrium between the gas and the surface of the sulfide layer. For example, at 800°C and Fig. 7 in Part I, the parabolic growth rate begins after approximately 1 day of sulfidation time. With decreasing temperature and decreasing partial pressure of hydrogen sulfide, the time necessary to reach gas-sulfide surface equilibrium is much longer. These observations are similar to those reported previously by Turkdogan et al.' on the oxidation of iron to wustite in hydrogen-water vapor mixtures. The slow approach to gas-sulfide equilibrium is well-demonstrated by the results in Fig. 1 where the square of the weight gain per unit area, ( g S per sq cmI2, is plotted against time for gas mixtures having PH g//>H = 1.0 with 0, 25, 50, and 67 pct Ar at 800°C. The value of 1.5 X lo-' (g S per sq cm)' corresponds to almost complete sulfidation of the iron strip (- 0.05 cm thick) to iron sulfide. The points fall on S-shaped curves. If the inflection parts of the curves are considered to be linear, thus indicating parabolic growth rate and the establishment of gas-sulfide equilibrium, their slopes would have to be the same for a fixed ratio in the gas mixture. Such is not the case, and the slopes for the "linear" parts of the S-shaped curves are lower than the value when gas-sulfide surface equilibrium is established. The subject matter of this paper is the kinetics of the surface reaction of hydrogen sulfide with iron sulfide during the early stages of sulfidation of an iron strip. EXPERIMENTAL RESULTS The apparatus and materials used were the same as those discussed in Part I. In the present experiments of relatively short duration, a purified iron strip, 5 by 2 by 0.05 cm, which was suspended in the uniform hot zone of a vertical zircon tube, reacted with a flowing gas mixture of hydrogen sulfide-hydrogen-argon. The sample was suspended from a gold chain attached to a calibrated silica spring. The amount of sulfur picked up by the iron, which formed a layer of iron sulfide, was determined by measuring the displacement of a reference point on the silica spring, using a cathetom-eter. In all cases, the degreased sample was first annealed in a stream of oxygen-free dry hydrogen for several hours to remove any impurities such as oxygen, nitrogen, or carbon which might have been present on the surface of the sample.' The rate measurements were carried out at 670°, 800°, and 900° C in hydrogen sulfide-hydrogen-argon mixtures with pH2 s/Ph2 ratios from 4 to 0.1. In a few experiments of short duration no sulfur deposition was observed in gas mixtures with (comments concerning sulfur deposition at high pH s/ph ratios were made in Part I.) Typical examples of the results obtained are shown in Fig. 2 for two temperatures and two gas compositions. With the present experimental technique, reproducible rate data could be obtained only after a uniform

Jan 1, 1969

Arrangements have been completed in New York whereby the re- sources of The Engineering Foundation, under the auspices of the four principal national engineering societies, are placed at the disposal of the National Research Council, which was appointed by the National Academy of Sciences* at the request of President Wilson. The object of the Council is to coordinate the scientific research work of the country in order to secure efficiency in the solution of the problems of war and peace. The Council was without funds until The Engineering Foundation, established to further scientific and engineering research, offered to place its resources at the Council's disposal, including the services of its secretary, Dr. Cary T. Hutchinson, to act as-secretary of the Council. The offer was accepted and plans for immediate activities have been placed in the hands of an executive committee. In indicating how thoroughly, every branch bf science and engineering is represented, Dr. George E. Hale, Director of the Mt. Wilson Solar Observatory, and Chairman of the Council, when he was in New York attending to the details of the arrangement, called attention to the personnel of the body, saying that it is the purpose to enlist the cooperation, in the solution of our industrial and military problems of a scientific character, of every possible established agency. Medicine, for example, is represented on the Council by Dr. William H. Welch, President of the National Academy of Sciences, Brigadier General William C. Gorgas, , Surgeon Crenera.1 of the United States Army, Dr. Simon Flexner, Director of the Rockefeller Medical Institute, and Dr. Victor C. Vaughan, Past President of the American Medical Society; biological science by Dr. Edwin G. Conklin, Professor of Zoology, Princeton University; chemistry by Dr. A. A. Noyes of Massachusetts Institute of Technology and Dr. L. H. Baekeland; physics by Dr. A. A. Michelson of the University of Chicago; and electricity by Professor M. I. Pupin, of Columbia University.

Jan 10, 1916

By William E. Souder, Eugene R. Palowitch

INTRODUCTION The longwall method of mining coal underground is now a highly developed and accepted mining technology. However, it was only through a long history of successes and failures that this technology now has the potential for reversing the declining trend in underground mining productivity in the United States. From its early beginnings in the United States during the 1800's, several species of longwalls have evolved. The evolutionary record consists of a series of overlapping birth-death eras, with each era giving way to another unique longwall technology. Typically, an era begins when some new longwall technology appears in response to a new technical opportunity or economic need. This new technology is adopted initially by only a few innovators. Later, other imitators get on the bandwagon and the technology diffuses throughout the user population. But evolving technical demands and socio-economic circumstances eventually cause many of the adopters to discontinue its use. This paper chronicles seven eras in the history of the evolution and utilization of longwall technologies in the United States. Some of the important factors that have influenced this history are discussed. Some distinctions are drawn between the operators who were first to adopt longwalls (innovators), and the imitators who followed. Statistics are presented which show that longwall mining is being adopted at an exponentially increasing rate, substantiating the forecast for a significant number of new longwall installations in' the future. Potential barriers to this increased utilization of long- walls are noted.

Jan 1, 1981

Such are the rigors of climate and topography of western Tasmania, that much of the area has remained uninhabited. The mountains, rising to peaks above 5000 ft high, receive the winds out of the west and precipitate 110 in. of rainfall a year on this coast. The drenched forests have a primordial look with such unfamiliar trees as the tru-sassafras, blackwood, cheesewood, ti tree, and man tree ferns. Prospectors speak of the "horizontals," trees which, in the dense foliage, grow out flat. When the explorer climbs over them he does not come back to the ground but continues forward on dense vegetation with the ground many feet below. Gold was discovered by the intrepid prospectors of the late nineteenth century and stamp mills were erected in the vicinity of Zeehan and Queenstown. At Mount Lyell, mining began for gold in the ironstone capping. The familiar story, of course, is that copper was found beneath the gossan and it was this mineralization that lead to permanent mining operations. Two companies began mining at Mount Lyell and their history from 1893 to 1902 was marked by an unreasonable competitiveness, human perversity and technical difficulties. The North Lyell and Mount Lyell companies were mining copper ores within one mile of each other separated only by a ridge. Each company built its own railroad and harbor. For six years of struggle both companies tried to work out the metallurgical problem which was the key to profit. Although they didn't know it, the two ores were complimentary and could have been smelted together. North Lyell ore was strong in silica and weak in iron, whereas Mount Lyell was fortunate in having a first-class metallurgist in Robert Sticht, from Brooklyn, N. Y., who in 1902 successfully achieved pyritic smelting without the use of carbon fuel.

Jan 10, 1964

By J. F. Wolff

The iron formation of the Iron River, Crystal Falls, and Florence districts probably is not of one geologic age only but of at least two ages. The ores, therefore, are of different characteristics. But in general the geologic conditions that occasioned the development of the orebodies have been essentially the same throughout the district and the types and structures of the orebodies are very similar in different parts of the area. In general, the iron formation of this area has been folded into a series of close pitching synclines and anticlines; minor folds of many orders are included in the major folds. The pitching synclines have been particularly favorable places for the circulation of ground waters, which in such troughs have developed orebodies through the familiar process of leaching out the silica in the iron formation, oxidizing and concentrating ferrous iron compounds in the rocks. The iron formation of this area is interbedded with and has interbedded in it certain slate or slaty layers that, in addition to the foot wall of the iron formation proper, act as impervious layers in the pitching troughs, to direct and control the flow of underground waters. In most places, the entire iron formation in a structural trough is not altered into iron ore; the orebody may be lens-shaped and exhibit no folding in its layers, outline, or shape, but almost without exception such bodies have been developed in folds and because of the influence of folds, and structurally they occupy only one limb of a fold. Many orebodies occupy the entire trough of a minor fold and the structure of the fold can be traced throughout the orebody. Many definitely recognizable horizon markers in or associated with the iron formation occur in this district and serve as valuable guides to the engineer or geologist in exploring an orebody whether by drilling or underground mining development. Among such markers are the talc schist (an altered dolomite) and the Traders slate at the base of old Menominee iron formation proper, and the interbedded Brier slates and overlying Hanbury dates; and certain graphitic slates and gray-wackel in the Iron River and Crystal Falls area.

Jan 1, 1925

By Henry A. Stiff, Lawrence E. Davis

A graphic method was developed which can be used to predict the tendency of oil field waters to precipitate calcium Sulfate under a variety of conditions. Application of this method is made to the prediction of sulfate scale formation in heater treaters. boilers. oil wells. cooling systems and water injection wells. INTRODUCTION A solution may be said to be in equilibrium with respect to a given salt when the concentration of that silt in equal to its solubility. If for any reason the concentration of the salt is increased or its solubility decreased. the equilibrium is upset and precipitation of the salt takes place. Thus, if the concentration of a salt in a particular solution is known and its solubility can be calculated for a given set of conditions, the tendency of this salt to form a precipitate under these conditions can be predicted. Based on these principles a method has been developed for determining the tendency of oil field waters to form calcium Sulfate precipitates under various conditions. THE SOLUBILITY DIAGRAM Calcium sulfate precipitation most frequently occurs when two waters are mixed: one containing calcium ions. and the other sulfate ions. As one of these waters is added to the other a point may be reached where the concentration of calcium Sulfate is greater than its solubility. thus causing the formation of a precipitate. The solubility diagram is a graphic device for determining the location of such points, thereby making possible a prediction of the tendency of such a system to deposit sulfate scale. A similar diagram can be used to solve many other problems involving the precipitation of calcium sulfate. Fig. 1 shows a solubility diagram representing the mixing of two waters. Water "A" contains a high concentration of odium, magnesium, and sulfate ions together with a small amount of calcium. Water "B" contains a high concentration of calcium ions together with sodium, magnesium and a small amount of sulfate ions. The percentage mixture of these waters is plotted along the abscissa of a system of rectangular coordi-

Jan 1, 1952

By A. S. Nowick, A. E. Roswell

Anelastic measurements of atomic mobility in an Ag-Zn substitutional solid solution, make possible a study of the rate of decay of lattice defects frozen into the alloy by quenching. A WIDE variety of experimental evidence has accumulated recently in support of the belief that atomic mobility or diffusion in face-centered cubic lattices occurs principally through the movement of lattice defects, as contrasted to a mechanism by which two or more atoms directly exchange lattice positions. The most direct evidence, summarized in a recent review,' includes the Kirkendall-effect measurements and anelastic measurements on quenched alloys. Theoretical calculations' have focused attention on the lattice vacancy as the defect probably responsible for diffusion in the common metals. Later calculations3 have also shown the possible importance of combined pairs of vacancies in producing diffusion. The only defect that has been considered seriously, in addition to the vacancy and combination of vacancies, is the "interstitialcy" (an atom which has left its normal lattice position and entered an interstitial position) ; the calculated energy of formation of an interstitialcy in a close-packed lattice is too large to permit a reasonable probability for the occurrence of this defect In view of these calculations it may be tentatively concluded that the defects producing atomic movements are single or multiple vacancies. Anelastic measurements of atomic mobility in substitutional solid solutions provide a valuable method for the study of lattice defects. By means of this method it was first demonstrated' that defects may be frozen into a lattice by rapid quenching from high temperatures. (It was subsequently shown6 that resistivity measurements may also be capable of detecting the presence of frozen-in defects.) A summary of the principles involved in these anelastic measurements will now be presented. The anelastic method is based on a relaxation phenomenon in substitutional solid solutions, first discovered by Zenera in a brass and subseauentlv investigated extensively in a series of Ag-zn solid solutions.' This relaxation effect may be observed in the usual way either dynamically, as a peak in

Jan 1, 1954

By Duk-Won Park

The PSU/MVS program, one of the computer programs for ventilation network analysis most recently developed at The Pennsylvania State University, was applied to the analysis of modifications to an existing ventilation system for a coal mine located in southern West Virginia. The program is well designed and has diversified capabilities which allow the users to make decisions on the optimum size and number of fans, the location and number of airshafts, and the optimum operational procedures. The mine had 10 working faces, from which the average production rate was about 5900 tons of clean coal per day. Two vane-axial mine fans were used in parallel at a shaft, and both of them operated simultaneously. One additional shaft was in the final construction stage and it would be used in four months to alleviate the load for the existing fans and distribute intake air more evenly. The overall ventilation surveys, including the altimeter pressure survey and the air quantity survey, were carried out in the mine entries, shafts, slopes, and gob areas. Computations were made using the above-mentioned computer program on the present condition and after one additional fan was placed in operation at the new shaft. Also, recommendations were made on the air route and fan blade settings for the most economical and efficient ventilation system. Further studies were carried out to decide the proper period when the third air shaft would be required according to the long-term mining plan. Additional branches were added for the next 4 years of the production plan, and the ventilation conditions were tested at the end of each year. Numerous combinations of blade settings and modifications of air routes were tested. It was recommended that the third air shaft be added at the end of the third year so as not to experience fan stall.

Jan 1, 1982

By AIME AIME

ALBERT PORTEVIN, distinguished French physical metallurgist .and savant, has been added to the Institute's list of Honorary Members. Professor Portevin's work in collaboration .with A. M. Garvin represents one of the greatest steps ever made in understanding the heat-treatment of steel and the function of steel-alloying elements. In addition, he has published the results of important work, on the castability of ternary alloys, on the determination of oxygen and-oxides in steel, and on high-temperature oxidationn and scaling of steel. Notable also are his studies on methods of testing metals, on the constitu¬tion and structure of alloys, on founding and welding, and on alloys of aluminum, magnesium, and copper. Professor Portevin was horn in Paris in 1880, entering

Jan 1, 1938

By J. W. Richards

There are two essentially different 'types of case-hardening processes; that using a dry mixture in which the object to be case-hardened is packed and kept for the necessary time at the necessary temperature, and the "liquid" proccss, employing a bath of fused salts into which the object is immersed and which by immediate contact case-hardens the surface of the article. The Shimer process belongs to the second class, and was a war emergency invention. Of the liquid melts used as baths, the most effective and most frequently used are melted potassium cyanide and melted sodium cyanide. These may be used either pure or mixed with salts that reduce the melting point and the percentage of .cyanide present. The use of these baths since 1914 has met many commercial difficulties because of the high price and frequent commercial scarcity of the cyanide salts; at present sodium cyanide has practically entirely displaced potassium cyanide. Another trouble is the danger to the workmen handling the cyanide salts, which are extremely poisonous, and the annoying and poisonous vapors or gases given off in the workshop, unless an effective system of hoods and ventilation is provided, so as to prevent the gases from the baths mixing with the air of the room. Porter W. Shimer, of Easton, Pa., has invented a substitute1 for the bath of melted cyanides which case-hardens with equal or greater facility and effectiveness, gives off no poisonous vapors, and costs for chemicals materially less than the cyanide costs in the previously used baths. The process has been in use over a year in a large American works and the following statement embodies the results of practical experience in the use and operation of the process. The Shimer liquid or melted bath consists of a mixture of easily fusible salts that do not possess case-hardening properties, into which is immersed fresh calcium eyanamid, which imparts to the bath case-hardening properties. The composition of the non-case-hardening salts appears rather immaterial. Good results have been obtained by using a mixture of sodium chloride, calcium chloride, and barium chloride in equal proportions by weight; also a mixture of one part sodium chloride

Jan 1, 1920

By Ernest A. Hersam

The rate of output of a rock crusher is based upon a certain space relation, the calculation requiring that the size and position of the jaws, the principle of motion, and the speed of the machine be known. The result is a calculated maximum output. The purpose of this paper is to develop a method of calculating this maximum output, to judge the general applicability or utility of such a calculation, and, so far as possible, to lecord calculated values as a basis for the comparison of actual results, or for estimating the capacity of a new crusher or of a standard crusher working under new conditions. A method for calculating the capacity of crushing rolls, which has been in common use for a long time, is well presented by R. H. Richards.' The output is conceived as a ribbon of rock, of which the breadth, thickness and length are governed respectively by the width of the rolls, the space between them, and their peripheral velocity. The weight of the rock thus crushed in a given time can be calculated from its specific gravity, after applying a factor representing the percentage of voids in the hypothetical ribbon. The calculation of crusher capacity is made in a somewhat similar manner. While the action of rolls is simple, with few irregularities in operating conditions, in rock crushers the material advances intermittently, usually under the force of gravity alone, and is subjected to a variety of variable conditions. The effect of these variable influences upon the calculation of capacity is now to be shown. In this paper, capacity will be discussed quite apart from any consideration of mechanical efficiency; that is, results will be stated not in terms of output per horsepower, but of output for a given machine when operated at a known speed, constructed and adjusted to receive material of a known size, and to yield a product having a definite maximum coarseness.

Jan 1, 1923

By D. L. Katz

In the management of oil properties, it is always desirable to know the future behavior of oil wells and oil reservoirs. Some estimation of the quantity of oil and gas that will be produced must be made as a basis for decisions on possible returns on investments in lifting equipment, drilling of additional wells, and other operating expenditures. In new or wildcat areas, operating expenditures are considered highly speculative, but in the completion of partly drilled and the operation of producing fields it is good business to remove as much speculation as possible. An accurate knowledge of oil and gas reserves in such cases would solve many management problems. The term "oil reserves" usually signifies the future ultimate recovery without specifying the method of production. Thus with changing methods and innovations in the production industry, reserves of any definite reservoir may be increased by increasing the portion of oil recovered. The usual reserve estimates are made by comparisons of well and formation characteristics, by using a percentage recovery on the oil content of the formation volume using porosity data, by extending production curves on non-prorated wells, or by extending bottom-hole pressure-production curves. The most reliable method would appear to be one that would estimate the initial quantity of oil and gas present and then obtain percentage recovery values for various productive methods and formations from experience. It is the purpose of this paper to describe a method of estimating the initial quantity of oil and gas present in a reservoir. The method is based on field operating data and the properties of crude oil-gas mixtures. The principles involved, the data required, the assumptions necessary, and an example of the method will be given. The method is entirely independent of sand volumes and formation porosities. Principles of Method The method of estimating the initial quantity of oil and gas present is based upon the premise that the volume occupied by oil and gas in the reservoir is constant and that a mixture of crude oil and gas will behave in

Jan 1, 1936

By D. L. Katz

In the management of oil properties, it is always desirable to know the future behavior of oil wells and oil reservoirs. Some estimation of the quantity of oil and gas that will be produced must be made as a basis for decisions on possible returns on investments in lifting equipment, drilling of additional wells, and other operating expenditures. In new or wildcat areas, operating expenditures are considered highly speculative, but in the completion of partly drilled and the operation of producing fields it is good business to remove as much speculation as possible. An accurate knowledge of oil and gas reserves in such cases would solve many management problems. The term "oil reserves" usually signifies the future ultimate recovery without specifying the method of production. Thus with changing methods and innovations in the production industry, reserves of any definite reservoir may be increased by increasing the portion of oil recovered. The usual reserve estimates are made by comparisons of well and formation characteristics, by using a percentage recovery on the oil content of the formation volume using porosity data, by extending production curves on non-prorated wells, or by extending bottom-hole pressure-production curves. The most reliable method would appear to be one that would estimate the initial quantity of oil and gas present and then obtain percentage recovery values for various productive methods and formations from experience. It is the purpose of this paper to describe a method of estimating the initial quantity of oil and gas present in a reservoir. The method is based on field operating data and the properties of crude oil-gas mixtures. The principles involved, the data required, the assumptions necessary, and an example of the method will be given. The method is entirely independent of sand volumes and formation porosities. Principles of Method The method of estimating the initial quantity of oil and gas present is based upon the premise that the volume occupied by oil and gas in the reservoir is constant and that a mixture of crude oil and gas will behave in

Jan 1, 1936

By Ernest A. Hersam

The rate of output of a rock crusher is based upon a certain space relation, the calculation requiring that the size and position of the jaws, the principle of motion, and the speed of the machine be known. The result is a calculated maximum output. The purpose of this paper is to develop a method of calculating this maximum output, to judge the general applicability or utility of such a calculation, and, so far as possible, to lecord calculated values as a basis for the comparison of actual results, or for estimating the capacity of a new crusher or of a standard crusher working under new conditions. A method for calculating the capacity of crushing rolls, which has been in common use for a long time, is well presented by R. H. Richards.' The output is conceived as a ribbon of rock, of which the breadth, thickness and length are governed respectively by the width of the rolls, the space between them, and their peripheral velocity. The weight of the rock thus crushed in a given time can be calculated from its specific gravity, after applying a factor representing the percentage of voids in the hypothetical ribbon. The calculation of crusher capacity is made in a somewhat similar manner. While the action of rolls is simple, with few irregularities in operating conditions, in rock crushers the material advances intermittently, usually under the force of gravity alone, and is subjected to a variety of variable conditions. The effect of these variable influences upon the calculation of capacity is now to be shown. In this paper, capacity will be discussed quite apart from any consideration of mechanical efficiency; that is, results will be stated not in terms of output per horsepower, but of output for a given machine when operated at a known speed, constructed and adjusted to receive material of a known size, and to yield a product having a definite maximum coarseness.

Jan 1, 1923

By H. Landsberg

IN a previous report1 it was pointed out that a successful attack on roof troubles has to be preceded by extensive scouting. As Lord Kelvin once said, scientific progress can be made only if accurate data are available: "unless you measure, you do not know.? THE CONVERGENCE RECORDER For the observation of roof movements in mines the convergence recorder has shown that it will enable us to get some of the necessary information. Results with convergence recorders were first published by Winstanley and other English investigators for rapidly moving longwall faces. In their investigations the speed of work and the heavy over-burden produced a considerable amount of absolute values of convergence in a short time. Under the conditions frequently encountered in our investigations in Central Pennsylvania, under shallow, overburden and in mines with slowly proceeding extraction, the movements observed were much less in absolute value, for an equal interval of time. This was partly because the mines in which our studies were carried on frequently had idle days, sometimes four or five in succession. Therefore continuous records were not employed and a simple convergence gauge was built. In its first models, it consisted only of two telescoping tubes pressed against roof and floor by a coil spring. At the side of the lower tube a rule divided into 1/-mm. divisions was fixed and a knife-edge, which was attached to the upper tube, was slid over the scale in case of convergence between roof and floor. While the larger motions could be read on this device, it seemed to be desirable to increase the accuracy by inserting between the two tubes a dial meter reading in 1/1000 in. Such a gauge was first built in April 1937 and installed for experimental purposes in a bituminous coal mine in Pennsylvania (Fig. 1). It was read at least once daily, 24 hr. apart, and if feasible at shorter intervals. After several months of experience it can be said that this type of gauge answers the scientific as well as the practical needs. It is easier to handle than the recorder; no clock is used, there are no pen troubles. The price of

Jan 1, 1938

By R. A. Wagstaff

Since the time of the early Egyptians, the use of copper: has been a boon to the life of most of the civilized world. Its use has been varied; in many connections, the art by which it attained its greatest usefulness has been lost. In this paper an endeavor will be made to take into consideration some of the many changes that have occurred during the last 40 years of copper-smelting operations. During that period the copper blast furnace has been almost forced out of existence by new methods of ore concen-tration—first, gravity concentration, and then flotation. These new methods of concentration introduced many new factors into the metallurgy of copper. The product was wet, it was fine and it was high grade. To overcome all these factors many changes have been necessary throughout the smelting agenda. New equipment has been necessary for transportation, unloading, sampling, bedding and moisturing in all smelting plants, especially the custom smelter' During the early days of "flotation," little was known about filtering or the use of an alkaline circuit; often the concentrate going to the smelter contained 2' to '5 Per cent moisture. It is easy to imagine the difficulty arising with a product of this nature when it had to be shoveled by hand labor. To meet these conditions, mechanical unload- ing and sampling devices were soon developed. In many instances such good progress was made that actual costs for handling this unfavorable product were lower than those formerly incurred on the old product. Today most sampling of copper ores and concentrates is being done by mechanical sampling, pipe or augur sampling, or shovel sampling. Where concentrates are uniform in metal content, a great many of the plants now use pipe or augur sampling. For spotty ores, the old shovel sample with cone and quartering during the final stages is still in' use. Where big tonnages are handled, mechanical sampling of concentrates is being done, with satisfactory results. To curtail slow and tedious cutting and mixing procedure, mechanical mixing boxes, splitters and cutters are used to cut down labor costs. Milling As crude ores become scarcer, the use of milling operations increases. The few crude ores that are still smelted are used as fluxing types. To use these ores finer grinding has been found advantageous. This has made for better bedding and fluxillg conditions, which in turn makes for faster smelting, lower fuel consumption and better metal recovery. The degree of fineness is more or less determined by the nature of the product. Most plants have set a standard of through 3/8-in. mesh screen for roaster -reverberatory smelting and through 3/4-in. mesh screen for converter fluxes. For some refractory Ores, even finer grinding has been found to be advantageous for good reverberatory smelting-

Jan 1, 1944

By Raymond B. Ladoo

Abrasives include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean or otherwise remove solid material, usually by rubbing action but also by impact (sandblasting, for example). They do not include abrasive tools-for instance, lathe tools and files-or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted although some chemical-action polishes and cleaners may also contain solid abrasives; for example, many automobile and metal polishes. General Considerations The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded grain abrasives such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cutting edges when grains become worn-for example, in garnet for sandpaper, neither highly cleavable or friable grains nor extremely tough grains are wanted. For still other uses, great hardness is objectionable; for example, abrasives for dentifrices and for glass-cleaning soaps. For the most efficient use in the more critical applications, the different types of abrasives are rarely completely interchangeable; thus, while crushed quartz and garnet are both used in sandpaper, the papers are not at all interchangeable in their use applications. In the last analysis, the choice of a high-grade abrasive depends upon the quality and quantity of work done by the abrasive per unit of cost. Initial cost of an artificial abrasive. may be much greater than that of a natural abrasive but the artificial abrasive may do so much better work than the natural one, and do it so much faster, that the ultimate cost will be less. It is on this basis that artificial abrasives have largely replaced natural abrasives for grinding metal. Classification Abrasives may be divided into two general classes, natural and manufactured. The former includes all rocks and minerals used for abrasive purposes without chemical or physical change other than crushing, shaping or bonding into suitable forms. Manufactured or artificial abrasives are made either by heat or chemical action from metals or mineral raw materials. On page 2 is a list of the most important abrasives, classified as to inherent types and as to forms in which they are used industrially. For most types of use there are manufactured products that can be substituted for the natural products, usually at higher initial

Jan 1, 1960

By W. J. Carlson, S. M. Parmerter, I. Iwasaki

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates. It also deals with the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when an-ionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were affected most strongly by the level of starch, to a lesser degree by the pH, and virtually not at all by the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semitaconite could be readily attained with starch and calcium chloride. A previous article discussed some of the parameters that are important when various corn starches are applied to the soap flotation of activated silica from iron ores and to the flocculation of iron ore slimes.' Methods of solubilizing the starches and the molecular size after mechanical and thermal treatments, as inferred from the viscosity measurements, were shown to influence the adsorption characteristics on iron ores, and the residual concentrations of both calcium ion and starch in the pulp liquor were in direct correlation with the flotation and flocculation behavior.2-4 The present article summarizes the results of more recent tests conducted to ascertain the role of starches and starch derivatives in various phases of iron ore beneficiation. The scope of this investigation has been extended to include not only anionic and cationic flotation, but also the flocculation and filtration of iron oxide slimes, the selective flocculation and partial upgrading of semitaconites, and the flocculation and clarification of magnetite-taconite tailings —all problems that are of vital importance to the iron ore industry of Minnesota. By combining a practical approach with adsorption studies and by using single-mineral systems5 in these research efforts, it is believed that the ultimate goal of developing a suitable modification of starch structure may be realized. The topics covered in this article are limited to the empirical aspects of the research program on the depressant activity of starches and products in the cationic and anionic flotation of silica and of their role in flocculation, water clarification and filtration. ANIONIC SILICA FLOTATION In the soap flotation of activated silica from iron

Jan 1, 1970

By Worthen Bradley, R. G. Hall

THIS paper will attempt to show how a metallurgical problem at one California quicksilver mine was solved, and how the solution was applied successfully at another mine. The pronouns "we" and "our," as used below, refer to the Bradley Mining Co. of San Francisco. The term "concurrent firing" for the purpose of this paper can be defined as feeding and firing a rotary kiln at the same end-that is, of course, the upper end. This is as opposed to "counter-current firing," the orthodox method, in which a kiln is fed at the upper and fired at the lower end. The terms "quicksilver" and "mercury" are used interchangeably. EARLY REFERENCES The earliest work on nonferrous metallurgy, we believe, was The Pirotechnia of Vannocio Biringuccio,1 its first edition having been printed in Italy in 1540. Quoting from its chapter entitled "Concerning Quicksilver and Its Ore": Quicksilver . . . is one of the gods and has divine strength in itself, and also, to the annoyance of the alchemists, it is winged. Hence, when it sees that it is in gravest danger, it loosens itself from . . . every bond . . . and flies away into the heavens, escaping from the hands of those who crucify it. Almost laughing, it leaves all its adversaries mocked and scorned, with their phials and filters empty . . . How thorough a job, under certain conditions, it can do of mocking its adversaries and leaving their phials and filters empty, was found out four centuries later at the Sulphur Bank mine, on the east shore of Clear Lake, in Lake County, California. The other mine mentioned in the title is the Reed, in Yolo County, California, 35 miles by road southeast of Sulphur Bank. Reed and Sulphur Bank ranked respectively fifth and seventh in U. S. production in 1943. The earliest direct reference we can find to furnacing troubles at these mines was by Thomas Egleston in 1890.2 Speaking of Sulphur Bank, Egleston says: Sometimes there is more sulphur than cinnabar in the ore, which is a detriment to both . . . making the sulphur impure, and rendering the cinnabar difficult to work on account of the soot. In some of the early . . . furnaces the accumulation of soot from the excess of sulphur has been known to penetrate as far as the fan blower at the end of the . . . condensers, and completely prevent its revolution. In order to get rid of the inconvenience of this accumulation . . . , as well as to get a commercial value from the sulphur, it (the sulphur) is now separated by steam and sold. It is claimed that the sulphur alone pays all the expenses of . . . the mine. The mine was first worked for sulphur, and the cinnabar it contained was considered to be an inconvenience, and was carefully picked out and thrown away. as its richness and value were not

Jan 1, 1945