Search Documents

By W. C. Winegard, C. Elbaum, T. Ojala

NONOCTAHEDRAL slip was observed in poly- crystalline aggregates of aluminum by Boas and Ogilvie.&apos; These authors indicate that the non-octahedral slip takes place on (100) or (110) planes. Ogilvie2 studied the continuity of slip lines across grain boundaries in polycrystalline aluminum. Non-octahedral slip was observed by him, but it was not reported to occur in the continuous slip lines across the grain boundaries, which were identified as octahedral slip in all cases. The present note reports the observation of non-octahedral slip in the grain boundary region of an aluminum bicrystal and tricrystal, both deformed in tension at room temperature. An analysis is made, which leads to a probable identification of the non-octahedral slip planes as (110) and (331). The specimens used were of rectangular cross section, approximately 5x10x200 mm. They were prepared by growth from the melt, using aluminum reported by the manufacturer to be 99.994 pct pure. The grain boundaries were in a plane perpendicular to the wider face and parallel to the long dimension of the specimens. The axis of tension was also parallel to the long dimension of the specimen. The orientations of the specimens studied were determined by the Laue back-reflection method and are given in Fig. 1. The nonoctahedral slip was first observed after about 6 pct extension in the bicrystal, and after about 2 pct extension in the tricrystal. The micrograph, Fig. 2, of the grain boundary region of the bicrystal shows two active slip planes throughout each of the two crystals, with a third plane active at the grain boundary in each crystal. Two major sets of slip traces observed in grain No. 1 are consistent with the operation of the slip systems (ill) [oil] and (111) [011]. The nonoctahedral slip takes place on a plane belonging to a <111> zone, as determined by drawing trace normals. Assuming that slip will take place only in the <110> direction, the planes in the <111> zone, which do not contain that direction, need not be considered. Among the remaining prominent planes of that zone, the (011) plane has a common slip direction—the [011]—with the (111) plane, which acts as one of the octahedral slip planes. In grain No. 2, a similar situation to that in grain No. 1 is observed. As indicated previously, the (oil) plane in the <111> zone, to which the nonoctahedral slip plane belongs, has a common [Oil] slip direction with the acting (ill) slip plane. Also, the orientation of the (oil) plane in grain No. 2 almost coincides with the orientation of the acting (111) slip plane in grain No. 1. Similarly, the orientation of the (oil) plane in grain No. 1 almost coincides with the orientation of the acting (111) slip plane in grain No. 2. It is, therefore, possible that the nonoctahedral slip was induced, in both cases, by octahedral slip in the neighboring grain. It is important

Jan 1, 1957

By Kraig W. Grubaugh, Lee W. Saperstein

Rapid growth rate of surface mining for coal has caused many states to increase the rigor and complexity of their surface mining codes. The promulgation of federal surface mining standards may cause those states containing federal land to amend their codes also. Presented is an up-to-date review of these codes with tabular summaries that divide the codes into operative functions. These summaries will be of use to new operators, multiple-state operators, and state officials. Suggestions are made for industrial efforts to present workable and acceptable amendments to these codes.

Jan 1, 1978

By William E. Ford, Edward Salisbury Dana

239, Contact-Gwiorneters. - The interfacial angles of crystals are measured by means of instruments which are called goniometers. The simplest form is the contact- or hand-goniometer one form of which is represented in Fig. 377. This contact-goniometer consists of a card on which is printed a semi- circular arc graduated to half degrees at the center of which is fastened a celluloid arm which may be turned to any desired position. The method of use of the goniometer is illustrated in Fig. 377. The bottom of the card and

Jan 1, 1922

By Dennis V. D’Andrea, Larry R. Fletcher, Peter G. Chamberlain

The evaluation of potential in situ copper leaching deposits requires a thorough examination of the geologic, mineralogic, hydrologic and physiological characteristics of the ore body. The decision to develop the deposit is made with these data along with leaching properties, estimated copper recovery, and economic analysis. A test blast followed by pilot leaching can a so be used for further evaluation and to reduce uncertainty regarding the deposit&apos;s potential. This report describes a number of ground characterization techniques that can be used to evaluate potential deposits. Field methods include geologic mapping, groundwater hydrology, core drilling, geophysical logs, permeability testing, and in-situ stress measurements while laboratory tests include assaying, mineralogy, leaching, rock physical properties, size analysis, and computer simulation.

Jan 1, 1980

By Guy R. Johnson

Like many other similar plants the ore-washer of the Longdale Iron Company has been a growth of years. In its principal features there is probably nothing new, as the type is that of the well-known " log-washer." Some of its minor details may, however, be of interest to those members who have to deal with the washing of large quantities of brown iron-ores, the principal gangue of which is clay. * Until 1883, the ore at Longdale, being of unusual purity, needed no washing, and was charged to the furnaces as it came from the mines—both lump and fine—the only attempt at cleaning being the&apos; picking over a screen of 1½-inch iron bars, 3½ inches from center to center, set in the top of the bins through which the cars for the furnaces were loaded." In 1883 it was no longer possible to win the ore by open cuts, and regular underground work became necessary. It was very

Jan 1, 1895

By Reno H. Sales

Jan 1, 1914

By George H. Hanna

THE importance of the Donets coal field (the Donbas) to the national economy of the Soviet Union is well known. Great as was the significance of this tremendous deposit of coal in prewar days it is destined to become an even greater factor in the economic life of the country now that the tremendous havoc wrought by the Germans is being remedied. Since the war began, new coal fields have been extended; for example output of the Moscow and Karaganda (Kazakhstan) fields has become considerably larger while new mines are producing coal in several parts of Uzbekistan and Kirghizia. The huge West Siberian coal field, the Kuznetsk Basin, is producing more coal than ever before to supply the industries of that region and of the Urals. But so great has been the development of industry to meet war needs, especially in those districts of the Soviet Union that lie to the East of the Urals, that the coal obtained, eked out by such locally-won fuels as peat and wood, is still barely sufficient to meet industrial requirements. The main burden of the coal supply for the restored industries of the West, therefore, will fall on the Donbas.

Jan 1, 1945

By Ernest R. Dickie

BRIEFLY, the ore body of the Bagdad Copper Corp., Bagdad, Ariz., is a monzonite porphyry carrying copper values fairly evenly distributed from the surface down through the primary zone. Tabular in shape, the ore body extends over several hundred acres. The oxidized zone averages about 60 ft thick and assays about 0.50 per cent copper. Under this is the chalcocite zone, or the zone of secondary enrichment, which averages about 100 ft in thickness and assays about 1.4 per cent copper. Under this zone lies the primary zone which extends in places to a known depth of about 150 ft and averages in grade about 0.60 per cent copper. Several years ago the block-caving method of extracting the ore from the chalcocite zone was installed. Then it was necessary to draw only about 250 to 300 tons per day, the capacity of the old milling plant. Early in 1943 the new 2500-ton concentrator was put into production. Drawing ore from the developed stopes in sufficient tonnage to furnish the mill at capacity proved unsuccessful in more ways than one. First, drawing the ore at an accelerated rate caused a large amount of dilution, there-by lowering the grade, and also caused funneling through to the surface. The surface material was detrimental to milling metallurgy and development of these stopes was costly per ton of ore extracted. The grade of ore decreased. making it impossible to maintain a mill head of over 0.9 per cent copper. The

Jan 1, 1947

By A. G. Journel

Accurate prediction of recoverable reserves are key to the development and planning of a mining operation. Recovery functions for tonnage, quantity of metal, and ore grade are defined and two approaches for their estimation are proposed. The indicator kriging (IK) approach draws on the data rank orders, whereas the multigaussian (MG) approach relies on a grade multivariate distribution hypothesis. Although based on different premises, both approaches yield remarkably similar, and reasonably accurate, estimates for recoverable reserves.

Jan 1, 1986

By R. A. Matuszak

Throughout the history of power excavating machines, engineers have continuously tried to shape the main drive speed- torque characteristics to provide an optimum from each main motion. Selection of prime mover for the various motions has been the subject of many engineering studies and most forms of energy conversion have been tried. A new form of electrical power conversion looms on the horizon as the most optimum yet. Controlled frequency operation of a squirrel cage induction motor increases the reliability of the most reliable form of energy conversion (electrical) found thus far, and improves the performance characteristics.

Jan 1, 1979

[ ]

Jan 1, 1938

By J. D. Dixon

Procedures are given for calculating stresses in underground tunnel supports which accounts both for the structural behavior of the support and that of the adjacent rock mass. Stresses in the support are caused by service loads and rock reactions. Service loads are due to rock pressures, hydrostatic and hydraulic pressures, selfweight of the support, or other utilitarian-type loads. Rock reactions, equal and opposite those in the support, are due to the deformational interaction that results as service loads deform the tunnel support against the adjacent rock mass. The procedures developed for solving this problem are an application of matrix structural analysis. The principles involved in this method allow for the consideration of the deformable characteristics of most tunnel support systems and an iterative solution procedure is applied to determine the areas of support-rock interaction. Numerical results of example problems are given.

Jan 1, 1972

By Dever C. Ashmead

Coal companies in the anthracite region are studying various methods of mining, seeking one that will shorten considerably the life of the gangway and thus decrease the maintenance charges. In steep pitching measures, the maintenance charges of the gangways are high because of the cost of replacing timbers and cleaning up falls. Therefore, if the length of the gangways can be decreased and the mining made more concentrated, the life of the coal gangways will be decreased and the maintenance charges per ton of coal produced will be smaller. The practice in the anthracite region is to drive long coal gangways and to work the breasts as the gangway from which they were driven is advanced. In many cases these gangways are from 4000 to 6000 ft. in length; and some are even longer. As these must be maintained not only until they have reached their limit but until second mining begins (which may be some years later), the maintenance charges are high. If the gangway is allowed to close, when the time comes to remove the pillars the cost of re-opening it may be as expensive as the original driving cost. The Lehigh and Wilkes-Barre Coal Co., at its Wanamie Colliery at Wanamie, Pa., has been using a system of mining that, as far as the writer knows, is not used in any other place in the anthracite fields. The

Jan 1, 1925

By William P. Blake

Eureka has for several years past been known as one of the most important centres of production of argentiferous lead in the country. The average daily yield is now one hundred tons of lead bars, in which the silver and gold of the ore is concentrated. The value of this lead, called " bullion," is about $300 per ton. To produce this quantity of metal, about four times the weight of ore, or say four hundred tons, is required. Most of this ore is supplied by the two leading mines of the district, the " Eureka" and the " Richmond," adjoining claims on Ruby Hill, about two miles from Eureka. There are, however, many other mines from which considerable quan-

Jan 1, 1879

By William P. Blake

(Read at the Amenia Meeting, October, 1877.) EUREKA has for several years past been known as one of the most important centres of production of argentiferous lead in the country. The average daily yield is now one hundred tons of lead bars, in which the silver and gold of the ore is concentrated. The value of this lead, called "bullion," is about $300 per ton. To produce this quantity of metal, about four times the weight of ore, or say four hundred tons, is required. Most of this ore is supplied by the two leading mines of the district, the "Eureka" and the "Richmond," adjoining claims on Ruby Hill, about two miles from Eureka. There are, however, many other mines from which considerable quan-

Jan 1, 1878

By J. L. Rodda

A large amount of time has been devoted to the microscopical study of the copper-zinc alloys, emphasis naturally being placed upon the commercially important alloys of the system. Suitable methods are available for microscopically recognizing the two phases richest in copper, but none appear to have been developed for the positive identification of the other phases. This is, however, accomplished, for the phases normally encountered, by an electrolytic method described in the following pages. Five phases of the copper-zinc diagram (Fig. I) are considered for the purpose of this paper: the solid solution of zinc in copper, alpha (a); the intermediate phases, beta (ß), gamma (?), and epsilon (e); and the solid solution of copper in zinc, eta (11). Beta prime is not considered a separate

Jan 1, 1937

By James E. Howard

At the request of the Council of the Institute, I have the honor to submit the following remarks upon the Program of Tests under which the current work of the Watertown Arsenal Testing Laboratory is carried on, which comprises, among other items, the tests of steel ingot metal and derivative shapes. The intended scope of the tests may be illustrated by extracts from the descriptive part of the program as submitted by the Laboratory under date of April 17,1907, and subsequently approved by the Chief of Ordnance, U. S. A. Under Item 1, Ingot Metal—Open hearth, acid and basic; Bessemer, acid and basic; crucible; fluid compressed and uncompreesed—descriptive remarks were made as follon-s: "A thorough, fundamental inquiry into the physical properties of steel necessarily begins with the ingot metal. Investigations, having for their object the improvement of steels, should also begin with the ingot. A knowledge of the ingot structure is essential for judging of the subsequent behavior or appearance of the metal. Under ordinary conditions, so little information is obtained from the ingot in individual cases that practically none of importance is acquired. These remarks have particular reference to the state of physical and structural

Jan 1, 1909

By M. C. Flemings, A. A. Tzavaras

Analytical and experimental procedures are descrihed for quantitative determination of volume-fraction microporosity in metals by mimorarlio-graphg. The analysis assumes spherical pores but allows for the observed fact that pores or portions of pores smaller than a given thickness do not project an image on the film. Volume-fraction microporosity was measuured in cast low-alloy steel and shown to vary from 0.6 x 10-4 to 10 x 10 depending on mode of solidification and on whether the material was air- or vacuum-cast. The aim of work described herein was to develop a method of quantitative measurement of the volume fraction of microporosity in cast metals. Microporosity, present in nearly all castings and ingots, is always interdendritic in nature and may be large enough to be seen on a polished surface with the naked eye. More generally, it is smaller in size, and its detection more difficult. Three techniques might be considered for measurement of microporosity: 1) lineal analysis of a polished metallographic surface, 2) density measurement, or 3) quantitative microradiography. As will be shown later, volume fractions of porosity in directionally solidified castings may be the order of 10-4 to 10-3; such small amounts of porosity are difficult to identify and measure on a polished surface. Density measurement is also not a suitable technique (for alloys) when the volume fraction of porosity is low. This is because the density of the base metal is often not known within the necessary accuracy, due to microsegregation or partial phase transformations. In general, it is not possible to completely eliminate microsegregation without also altering the porosity. Because of the limitations of the foregoing techniques, quantitative microradiography was employed to determine amount of porosity. In recent work, microradiography has been found to be useful for qualitative measurement of porosity, including determination of size and shape of individual pores;&apos;)&apos; however, quantitative determination of amount of porosity has not been attempted. I) CALCULATION OF VOLUME-FRACTION POROSITY The following analysis employs procedures similar to those of Cahn and Nutting3 and Hilliard.4 Major simplifications are that pores are assumed to be spherical and to be present in sufficiently small quantities that no overlapping occurs. A basic difference from the previous treatments is that the limited "sensitivity" of microradiography is considered. Assume first 1) cavities are spherical and of uniform diameter, 2) cavities are randomly distributed, 3) volume-fraction porosity and specimen thickness to pore radius ratio are sufficiently small that overlapping of the projected images of cavities is negligible, 4) sensitivity is limited (i.e., holes or portions of holes of less than a given thickness do not project an image on the film). The sensitivity, is defined as: where 5 = minimum thickness of void from which an image will be projected on the film and t = specimen thickness. Now, from Fig. 1, it is possible to distinguish between two different types of holes. These are 1) holes whose centers lie within the region t/2 > X > 6/2, where X is distance from one surface of the specimen (positive into the specimen), and 2) holes whose centers lie within the region (6 — r) < X < 6/2, Holes whose centers lie outside X = (6 -r) project no image on the film. These two types of pores are considered separately below. Type 1 Pores. When 6 is greater than 0, the image of a spherical cavity of radius r appears on the film as a circle of radius a which is smaller than r. From geometry, Fig. 1: a2=r2-52/4 [2] where a = radius of image of pore on film and r = radius of pore. Since the pores are randomly distributed and spherical V =4/3pr2Nv [3] where V = volume fraction of voids and Nv = number of pores per unit volume and the number of images of Type 1 pores per unit area of film, N&apos;A, is

Jan 1, 1965

By E. V. Howard

During the recent expansion of precipitate copper production at the Chino Mines Division of Kennecott Copper Corp., Santa Rita, N. Mex., local studies of the dump leaching process were intensified. As these studies progressed, it became apparent that a reliable method for locating leach solutions within the dump was required, since the contact between the leach solutions and the copper-bearing ma.teria1 determines recovery. In the past, the problem of determining leach solution contact has been attacked by various methods, including destructive testing (dump dissection), indirect observation (such as chloride or dye tracers) and mathematical or laboratory model studies, but they have not proved completely satisfactory. The investigation of methods for in situ observation of leach solutions led to consideration of radiation logging in drillholes, which are subsurface techniques used in petroleum exploration and development for locating fluids and measuring porosity. A significant advantage of radiation logging is that, unlike other types of logging, measurements may be made in cased holes, since gamma rays and neutrons will penetrate steel and cement. Three techniques are currently used at Chino: Natural gamma ray logging; neutron-neutron, or moisture logging; and gamma-gamma, or bulk density logging.

Jan 4, 1968

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1985