Search Documents

By B. C. Craft, Murray F. Hawkins, John R. Rayne

A reservoir mechanism of sulfur recovery by the Frasch process is presented. Improving the economic, of recovery appears to be largely a well, rather than a reservoir problem. A most important factor is the limitation of the lateral extraction of .sulfur about the wells due to the almost vertical .flow of the injected hot water. Model studies are described which confirin the mechanism of sulfur recovery by presently used methods. Studies on a five-spot system indicate improved econo171ics regarding recovery, recovery rate, therinal efficiency, and well spacing. INTRODUCTION Sulfur mining by the Frasch process is one of the most important methods of sulfur production. Developed by Herman Frasch in 1894, it enjoyed a rapid growth and presently supplies 40 per cent of the world's sulfur and about 80 per cent of the U. S. sulfur." The Frasch process of mining the underground native sulfur deposits involves melting the sulfur in place by introducing super-heated water into the sulfur bearing formations, and producing the sulfur as a liquid. Many problems are encountered in mining these native sulfur deposits, and sulfur production depends chiefly upon the nature of the sulfur deposit and the underground thermal efficiency of the heat transfer system. THE RECOVERY MECHANISM Sulfur is typically found in salt dome cap rock as crystal aggregates occurring within the cavities, seams, and pores of limestone and gypsum formations.' Sulfur-bearing limestone is typically cavernous, vugular, and fractured. Porosity averages about 20 per cent and sulfur saturation averages approximately 25 per cent by weight.1,15 Vhe sulfur bearing formations are very heterogeneous in nature and physical characteristics vary widely within small distances. Total cap rock thickness may vary from 50 to more than 1,000 ft, and net productive thicknesses from a few feet to a few hundred feet. In most cases the upper portion of the limestone formation is barren of sulfur, varying from 5 to 200 ft in thickness.1,15,33 The immediately overlying sediments and the underlying dense anhydrite formation provide permeability barriers to the flow of water from the cap rock section.'" Sulfur wells are drilled with conventional oilfield drilling rigs. Fig. 1 illustrates the casing program of a completed sulfur well. The cap rock sections are drilled with core bits and continuous core logs are recorded. After coring, the cap rock section is underreamed to a diameter of 9 7/8 in. The bottom of the 8-in. casing is welded closed and rests on the bottom of the drill hole, which extends through the cap rock to a few feet above the bottom of the sulfur-bearing formation. The 8-in. pipe contains 5 ft of 3/4-in. perforations on 6-in. centers and 15 ft of 1-in. perforations on 1-ft centers. The 20-ft perforated section is set opposite the lower 20 ft of the sulfur-bearing formation. The 4-in. sulfur pipe is set inside the 8-in. water line on a seat ring at the top of the 5-ft section of 3/4-in. perforations. The mining water, heated to about 330°F under a pressure of 250 psi, is forced down the annulus between the 8-in. and 441-1. pipes and through the 1-in. perforations to the sulfur-bearing formation. Compressed air, at 400 psi pressure, is supplied through a 1-in. air line near the bottom of the well to provide air-lift of the liquid

Jan 1, 1957

By D. Weinstein

The high temperature mechanical properties of stainless steels after fast neutron irradiation are discussed in the light of effects caused by lattice dattmage and effects caused by helium generated from n,a transmutations. Embrittlement at high temperatures is due to helium accumulation at grain boundaries and to cavity formation and proPagation along grain boundaries. Following from the embrittlement mechanism, it is suggested that when deformation occurs by mechanisms associated with super plasticity, helium ac-curnulation at boundaries should be attenuated and cavities, if formed, should be nonpropagating. As the mean free Path between interphase boundaries of a two-phase Fe-Cr-Ni alloy was decreased, the degree of superplastic deforrnation at 870°C increased, as vneaszired by total elongation and by the expottent m = a log 'a/a log 'i. This alloy and type 304 stainless steel were cyclotron irradiated in an a-particle beam to a helium concentration of -1 x 10 atom He per atom. The stainless steel specimen was embrittled, but the ductility of irradiated two-phase Fe-Cr-Ni alloys correlated with the values of. m during 'defor-malion. The .finest grained, helium-injected specimens that deforrned with highest m values exhibited the largest elongations to ,fracture. These results could be correlated with metallographic observations of cavity behavior: the propensity for intergranular propagation was lessened as the m value increased. It is concluded that superplastic deformation is ef-fectizle in attenuating helium embrittlement at elevated temperatures. One of the principal problems associated with development of fast breeder reactors is application of alloys such that suitable fuel cladding results. Stainless steels and other Fe-Cr-Ni alloys, because of highly acceptable nuclear characteristics, represent the primary materials for this component, and an exhaustive research and development effort is being conducted. The main deficiency of these materials has been a severe loss of ductility at high temperatures after fast neutron irradiation. An extensive body of mechanical property data and microstructural observations has provided an adequate phenomenological description of embrittlement; in conjunction with transmission electron microscopy studies, a reasonably acceptable embrittlement mechanism has been obtained. Following from this mechanism, it is suggested in the present work that ductility would be enhanced if deformation could occur by mechanisms associated with the phenomenon of superplasticity. Experiments to test this hypothesis have been conducted, and the results are presented and discussed in this paper. IRRADIATION EMBRITTLEMENT AT HIGH TEMPERATURE Austenitic stainless steels have been irradiated to accumulated fast neutron fluences of 1020 to 1022 nvt at temperatures between 60" and 600°C. Specimens that have been exposed to these conditions and subsequently tensile tested at temperatures between 600" and about 900°C exhibit approximately 5 pct total elongation to fracture.'-3 For unirradiated specimens receiving a nearly identical thermal exposure, total elongation at these test temperatures is about 45 pct. Examination of irradiated specimens has shown that fracture propagation is entirely intergranular. These phenomenological aspects of irradiation embrittle-ment at elevated temperatures are well known and are not generally disputed. Although the explanation of this phenomenon has been controversial, a mechanism for ernbrittlement has emerged that accounts reasonably well for the observed mechanical behavior. The controversy resulted primarily from an indeterminate role of neutron-in-duced lattice damage, if any, and a presumed, but experimentally unverified, contribution to embrittle-ment from helium generated by n,a transmutations. Recently, Holmes and coworkers4 have conducted experiments that separate these effects, and the results are instructive in formulation of the ernbrittlement mechanism. Holmes el al.4 irradiated type 304 stainless steel in EBR-I1 to a fluence of 1.4 x 1022 nvt (E > 0.18 mev); the irradiation temperature was 538" * 48°C or, in terms of absolute melting point, 0.49 * 0.03 T,. After irradiation, tensile tests were conducted at temperatures of 21" to 870.C, the specimens first being annealed for 30 min at each test temperature. In addition, thin sections of irradiated specimens were annealed for 1 hr at identical temperatures, electro and examined by transmission electron microscopy. Thus, for a given temperature, it was possible to correlate mechanical properties with the defect structure. At room temperature, the yield stress of irradiated specimens was a factor of 2.5 higher than unirradi-ated specimens exposed to an equivalent thermal history. Electron microscopic examination of the irradiated specimen revealed a high density of lattice damage in the form of Frank sessile dislocation loops and polyhedral voids. Holmes et al.4 concluded that the presence of this defect substructure caused the increase in yield stress and that after irradiation in a fast neutron flux at 0.49 Tm, substantial lattice dam-age persists. Annealing at progressively higher tem-

Jan 1, 1970

By K. N. Han, H. Lee, M. C. Fuerstenau

An investigation of the recovery of finely-divided cassiterite and silica particles less than 1 µm (1200 mesh) in size has been carried out using packed and fluidized beds. The bed particles used included cassiterite and silica particles ranging from 44 to 210 µm (325 to 70 mesh). Effects of various system parameters on the recovery and selectivity of cassiterite fines were investigated. System parameters included pH of the slurry solution, superficial velocity, slurry concentration, and bed particle sizes. High recoveries of cassiterite fines were obtained at pH 4.0 and slow slurry flow rates. In a packed bed system, recovery of cassiterite fines was greater than 95%, while that of silica fines under the same conditions was about 35%. Although the total recovery per pass is not as good as the packed bed, the fluidized bed system exhibits good recovery in general and an excellent selectivity of cassiterite fines. There is an optimum superficial velocity, vo, for the rate of fine particle uptake and the apparent rate constant has the form of Kvo1/2- K'vo, where K and K' are system constants.

Jan 1, 1985

By B. W. Levinger

THE system Ti-CI- has been studied by several investigators." ' Though titanium and chromium are completely miscible at high temperatures, an intermediate phase of the approximate atomic proportions TiCr, has been identified at various compositions between 60 and 68 wt pct Cr. The structure of this phase was established as the cubic C15 (MgCu2) type with 24 atoms per unit cell and a lattice parameter 6.929 kX.2 During a study of the ternary system, Ti-Mo-Cr,5 the existence of a high temperature modification of the TiCr, phase was discovered. In a series of alloys annealed at 1300°C and containing from 60 to 70 wt pct Cr and 5 pct Mo, a new phase was present which did not correspond to either ß solid solution or TiCr,. By trial, the new phase was identified to be of the hexagonal C14 (MgZn2) structure with 12 atoms per unit cell. Further work showed that the hexagonal structure was. in fact, also present in binary Ti-Cr alloys quenched from high temperatures. To make the identification more certain, the intensities of the various reflections were calculated assuming a composition TiCr2 and C14 structure. Table I lists reflection planes, interplanar distances, calculated intensities, and a comparison of these values with the lines of a binary Ti-Cr alloy (66 pct Cr) annealed for 20 min at 1385°C and water quenched. Since high angle lines were more diffuse, the correspondence between visually observed and calculated intensities was not as good at these angles. Lattice parameters were computed to be a = 4.922 kX, c = 7.945, c/a :- 1.614. The corresponding interatomic distances are: titanium to titanium distance, 3.00:, kx, chromium to chromium distance, 2.43, kX, titanium to chromium distance, 2.88,, kX. These compare to 3.00, 2.45, and 2.87 kX in the cubic phase, respectively.' The atomic positions in the C14 structure are as follows: Titanium 1/3, 2/3, Z; 1/3, 2/3, 1/2: 2/3, 1/3, i; 2/3, 1/3, (1/2-z); Chromium 0, 0, 0: 0, 0, 1/2; 2x, 2, 1/4; 232, x, %; X, 22, 1/4; X, 2x, 3/4; x. x, 1/4; x, x, 3/4; The values of x and z were calculated for the alloy mentioned and found as follows: z — 0.061, x = 0.165. The values assumed in the intensity calculations were those for an ideal close-packed lattice or z = 1/16, x = 1/6. Work in the Ti-Mo-Cr system indicates that y2 the hexagonal modification of TiCr2, is the stable phase above 1300°C, while y1 with the cubic structure is stable below 1000°C. X-ray examination of a number of alloys annealed at intermediate temperatures showed that the hexagonal and cubic phases can coexist. Alloys quenched from 1000°C and annealed at 1100" and 1200°C showed small amounts of y2 at the higher temperature. A considerable amount of y, seemed present, however, in cast alloys annealed at 1100°C. It further appears that there is a small but definite solubility range for both phases in the ternary system. Acknowledgment The results of this paper represent work carried out in conjunction with a project sponsored by Watertown Arsenal, Contract No. DA-11-022-ORD-272. References 'M. K. McQuillan: Journal Inst. Metals (1951) 79, p. 379. 2 P. Duwez and J. L. Taylor: Trans. ASM (1952) 44, p. 495. W. J. Van Thyne,. H.. D. Kessler, and M. Hansen: Trans. ASM (1952) 44, p. 974. 1 F. B. Cuff, N. J. Grant, and C. F. Floe: Trans. AIME (1952) 194, p. 848; Journal of Metals (August 1952). Unpublished Research, Armour Research Foundation. "H. J. Wallbaum: Ztsch. Krist. 103, p. 391.

Jan 1, 1954

By P. M. Budge, William L. Fink, Kent R. Van Horn

The investigation of the phase relations of high-purity aluminum-base alloys is a part of the fundamental research program of the laboratories of the Aluminum Company of America. The results of a number of binary and ternary systems have previously been published in the Transactions of this society. The aluminum end of the binary aluminum-titanium system has been studied. This system has received relatively little attention. To the authors' knowledge, there are two previous papers on this subject. E. van Erckelensl determined the constitutional diagram reproduced in Fig. 1. According to this diagram, the liquidus represents the separation of TiA14, (Ti = 30.7 per cent.). He concluded that this is the composition of the compound, because in his work the eutectic horizontal terminated at 30.7 per cent. titanium and the metallographic examinalion of a sample of this composition revealed only one phase. According to the constitutional diagram developed by W. Manchot and A. Leber,² reproduced in Fig. 2 from data given in their article, the liquidus represents the separation of the compound TiA13 (Ti = 37.2 per cent. ). The composition of the compound was derived in a manner similar to that utilized by van Erckelens. Moreover, Manchot and Leber confirmed the composition of the compound by analysis of the constituent left as a residue after dissolving the alloys in weak sodium hydroxide solution. Although these are the only publications describing the constitution of the system, other investigators have studied the composition of the titanium compound. L. WÖhler3 says that there is a compound TiA13 which was later confirmed by W. Manchot and P. Richter4 and by

Jan 1, 1931

The importance, validity, and acceptability of the Paley Report has become the great issue of the minerals industry. A 12-man panel made up of representatives of various facets of the industry sat down at the 1952 Mining Congress Show in Denver in an attempt to clarify the many opinions currently held concerning the report. Howard Young, deputy administrator of the Defense Materials Procurement Administration, noted that the report had caused more discussion and serious thinking than any other government report, He did not subscribe to the "have not" principle, however, but called it a "need more" principle. Horace M. Allbright, president of U. S. Potash Corp., believes industry should continue to develop the report. He cited the editorial appearing in the September, 1952 edition of Bining Engineering,,, "Don't Let It Die," as expressing his feelings. Edward Snyder, president of Combined Metals Reduction Corp., says the statistics used in the report were used to promote a false international policy. He sees the report as a master plan for the development of the superstate. He also stated that the-ore reserves given in the Pales, report represent only 10 pct of what is actually available.

Jan 1, 1952

By David R. Mitchell, R. B. Hewes

MANY processes for cleaning coal that are in use depend primarily on physical properties of coal and refuse other than specific gravity and surface conditions relating to froth flotation. These properties are' shape, coefficient of sliding friction, resilience, friability, magnetic susceptibility, and electrical conductivity. In many of these processes specific gravity does have some effect and many separators are designed to utilize more than one of the physical properties cited. Although the processes described herein do not have a widespread application, yet for specific coals and specific conditions, they are economically important. A problem confronting many coal-mining districts is the marketing of the slacks or screenings and dust passing the final sizing screens. Proc¬esses in commercial use installed primarily to increase the form value, and hence the market value, of these slacks and dusts include briquetting, packaging, and low-temperature carborization. MECHANICAL PICKERS Machines utilizing shape, frictional resistance, and differences in resilience of coal and impurities are usually called mechanical pickers. They require a closely sized feed, therefore their use is confined to the pea, nut, and egg sizes. Various types of these devices are described by Berrisford, 1. 2 Taggart, and Yeele.

Jan 1, 1943

By R. H. Heyer, J. L. Bray, M. E. Carruthers

It is well known that iron markedly improves the physical properties and casting characteristics of aluminum bronzes. The use of 1 to 4 per cent iron as the principal modifying addition has become common practice in many foundries melting aluminum bronzes. Although the beneficial effects of iron are unquestioned, there is some uncertainty regarding the structural changes caused by it in the basic copper-aluminum system. It is agreed that a new constituent appears in abundance when the iron content reaches 2 to 4 per cent. This constituent, which frequently occurs in shapes resembling clover leaves, is sometimes assumed to be an aluminum-iron intermetallic compound. If this were correct we might expect a change in the structural relationships of the matrix in the direction of decreased aluminum content. On the other hand, it has been reported that iron has a negligible effect in altering the fundamental relationships of copper-aluminum alloys1 Others2'3 have reported an additive coefficient. Apparently it will be necessary to know the equilibrium relationships between the phases of the copper-aluminum-iron alloy system to establish any such theory as fact. When this has been done it may very well be that a further revision in the structural relationships may be necessary to describe the changes to be expected in commercial cast alloys. It was with this latter problem before them that the authors attempted to determine the change in the copper-aluminum relations with respect to iron. Objects of the Investigation In certain investigations carried out by the authors for a plant producing a large tonnage of cast aluminum bronzes the structures

Jan 1, 1936

Freeport's Floating Mine Begins Sulphur Operation Eight years of research were culminated when Freeport Sulphur Co.'s floating mine plant went into operation on Bay Ste. Elaine in the remote Louisiana bayou country 60 miles southwest of New Orleans.

Jan 1, 1953

By H. Doi, Y. Fujiwara, K. Miyake

In order to throw light on the mechanism of plastic deformation of WC-Co alloys, compressive tests of WC-(7 to 43) vol pct Co alloys have been carried out at room temperature, and stress-micro strain relation has been investigated in detail. The analysis of the factors affecting the yield stresses reveals that the yield stresses can be predicted by modified Oro-wan's theory if one properly estimates the planar in-terfiarticle spacings. Conzpressive straining of some of the alloys by 0.066 to 0.17pct increases the decrements by a factor of as much as 3.4 to 14, whereas the corresponding increase in the electrical resistivities is less than 10 pct. The analysis of the decrement data in terms of -Gramto and Lücke theory shows that the marked increase is attributed to increased dislocation darnping itt the binder (cobalt) phase. By cornbilling the decrement data and the conzjwession duta, one obtains the relation between flow stress in shear (?t) and increase in dislocation density (p): At = const . v6 . This is interHeted to mean that the mechanism of strain hardening of CirC-Co alloys is essentially sarne as the one for dispersion strengthened alloys. The possible effect of bridge formations between the carbide particles has also been examined. OWING to the combination of hardness, strength, and other physical and chemical properties, WC-Co alloys have opened the way for unique fields of applications, the recent ones being, for instance, anvils for super-high-pressure generation apparatuses. In such applications, the alloys are frequently subjected to very high compressive stresses: these stresses may cause the alloys to deform plastically and eventually to fail. However, much remains obscure regarding the nature of the plasticity of the alloys. Evidently, the alloys owe their high strength to the hard carbide particles which frequently occupy as much as 80 to 90 pct in volume fraction, whereas the ductility required for practical applications is provided by the small amount of the binder phase between the carbide particles. When the volume fraction of the carbide phase is not very large, deformation behavior of the alloys may be described by some of the current dispersion strengthening theories. However, greatly increasing the carbide phase is thought to lead to some carbide skeleton structure or bridge formations owing to the increased chances for direct contacts between the carbide particles;1,2 this may appreciably affect the plasticity of the alloys. Regarding the effect of formation of the carbide skeleton structure, it is interesting to note the work by Ivensen et al.3 on compression tests of the alloys containing somewhat large carbide particles; they observe extensive generation of slip bands in the carbide particles after application of some preliminary compressive stresses. They interpret the results in terms of plastic deformatiot: of the carbide particles which are supposed to have formed a skeleton structure; the binder phase plays only a passive role, at least in the early stages of the deformation. That carbide crystals exhibit microplasticity at room temperature is apparent from the work of Takahashi and Freise4 and French and Thomas5 on indentation of WC single crystals. On the other hand, Dawihl and coworkers6-10 maintain that even when volume fraction of the carbide phase is very large (for instance, more than 90 pet), a very thin binder layer generally exists between the carbide particles. They interpret the results of the extensive mechanical tests in terms of the plasticity of such a layer. Gurland and Bardzil11 point out that decrease in ductility of the alloys with increase in the carbide phase is caused by the effect of plastic constraint exerted by the dispersed carbide particles. Drucker12 further develops this concept from a continuum-mechanics approach on an assumption that a continuous thin binder layer separates the carbide particles. A common feature of the studies reported so far on the plasticity of the alloys is that the information deduced is invariably qualitative in nature. Thus, very few systematic experiments for obtaining reliable and sufficiently detailed stress-strain curves of the alloys varying widely in the microstructural features have been carried out. In particular, it may be of special interest to investigate in detail the early stages of the plastic deformation of the alloys in order to shed light on the strengthening mechanism. However, such work appears to be extremely rare. Doi et al.13 recently reported a first brief account of the results of some quantitative analysis of the plasticity of the alloys in terms of dislocation theory. Their experiment was rather limited in the composition range covered (volume fraction occupied by the carbide phase: 79 to 83 pct), and thus they could not necessarily elucidate the controlling mechanism of plastic deformation of the alloys of a more general composition range. Consequently, in the present investigation, deformation behavior and some other physical properties of the alloys were investigated and discussed in more detail over a much wider composition range. SPECIMEN PREPARATION WC-Co alloys used in this experiment were prepared in cylindrical or rectangular form by sintering in vacuo compressed mixtures of tungsten carbide and cobalt

Jan 1, 1970

By Philip B. Bucky

[CONTENTS t. How Does One Determine WhetherPAGE an ore Body Will Block-cave?R. W. Hughes13 Sherman R. Burdick 13 PAGER. T. Gallagher 14 Mark A. Smith 2 C. F. B. Price, Jr.14 Harry A. Leidich2Benjamin F. Tillson 14 McHenry Mosier2C. F. Jackson14,17 R. W. Hughes2R. Taborelli15 Sherman R. Burdick3Frank A. Ayer16 R. T. Gallagher 3Philip B. Bucky16 Benjamin F. Tillson 3Rollin Farminr6 Lucien Eaton 3J. L. G. Weysser15, 0,17 C. F. Jackson 3George S. Rice17 Philip B. Bucky32. How Does One Determine the Block4. What Determines the Procedure in Dimensions and the DevelopmentRemoving Caved Ore? Work Necessary to Make an OreHarry A. Leidich17 Body Cave?McHenry Mosier17,21 Mark A. Smith 5,7,() R. W. Hughes17 Harry A. Leidich6Sherman R. Burdick 18 McHenry Mosier6,7,12 R. T. Gallagher 18 R. W. Hughes6Mark A. Smith I8 Sherman R. Burdick 7Philip B. Bucky20, 21, 23 R. T. Gallagher 7C. F. B. Price, Jr20 Benjamin F. Tillson 7,11R. H. Bennett21 L. E. Young7C. F. Jackson 21, 23 Robert D. Hoffman8, 1 2Gerald Sherman 3 . 21 Gerald Sherman8Tell Ertl21 Philip B. Bucky10, 11, 12G. K. Foster 23 R. S. McClellan 12C. H. Shoemaker23 Tell Ertl 12 3. How Do the Forces Act and What Are5. What Are the Criteria for Determining the Stresses Developed in a Blockthe Efficiency of a Block-caving That Cause It to Block-cave?Operation? Mark A. Smith 12, ISHarry A. Leidich23 Harry A. Leidich13McHenry Mosier24 McHenry Mosier13R. W. Hughes24 Sherman R. Burdick 24 R. T. Gallagher 24]

Jan 1, 1942

By Edna A. Dancy

Jan 1, 1965

By K. M. Rolls, F. W. Reuter, J. Wulff

The superconducting behavior and microstructural characteristics of a nominal Nb-40 wt pct Ti-0.239 wt pct O alloy were studied as a function of ther mo -mechanical processing treatment. Critical current density us applied transverse magnetic field was obtained for 0.010-in.-diam wires at 4.2°Kin steady fields 14 to 110 kG. Both optical metallogvaphy and transmission electron microscopy were used to delineate the micros tructures of the same wires. It wan found that a 1-hr 500°C precipitation heat treatment after cold drawing to final size led to the highest critical current density. Heat treatment at 600°C also led to a high critical current density, but the precipitate differs in kind and form from that at 500°C. The resistire critical field was also found to be sensitive to precipitation heat treatment since the effective composition of the superconducting phase changes. This is discussed in terms of the oxygen in interstitial solid solution. Two types of high-field superconducting wire are at present used in the construction of high-field superconducting solenoids. These types are solid-solution alloy wire such as Nb-Zr and Nb-Ti and composites of the brittle inter metallic compound Nb3Sn. The latter generally have a high super cur rent-carry ing capacity which is difficult to vary if properly made. The supercur rent- carry ing capacity of the former can be varied drastically and often predictably by suitable thermomechanical processing treatments. In general, the critical current density Jc of the solid-solution type of alloy is increased by cold work and by additions of interstitial elements along with aging heat treatments. The imperfections which result are be-iieved to be responsible for the observed increase in Jc. In 1962 Kneip and coworkers1 found that the critical faurrent density of Nb-Zr alloys could be increased by proper heat treatment preceded and followed by cold work. Betterton and coworkers2 using a Nb-25 at. pct Zr alloy found that small additions of oxygen or carbon enhanced the effect of this heat treatment. They suggested that the interstitials present aided precipitation in the alloy, leading to a filamentary structure with superior properties. If the precipitation heat treatment was omitted, interstitial additions had a negligible effect on Jc. wong3 showed that higher heat-treatment temperatures lowered Jc. Walker and co-workers,4 who studied microstructure (by transmission electron microscopy) as well as superconductivity, found that the Jc anisotropy introduced by cold rolling was itself affected by heat treatment. They were unable to clarify the relation between microstructure and critical current density, although evidence of precipitation was indicated. More recent investigation of Nb-Zr alloys,5,6 besides showing that structural defects and fiber ing due to cold work and precipitation serve to raise Jc, also elucidate important optically observable microstructural changes which occur upon precipitation. In these reports, coarsening of the microstructural features was found to decrease Jc. Vetrano and Boom,7 who studied Ti-20.7 at. pct Nb, found that Jc was increased to a maximum by a 415°C, 3-hr heat treatment following quenching from 800°C and cold working. Heat treatments can also affect the resistive critical field Hr. Final-size heat treatments of Nb-Zr wire can lower Hr drastically if gross phase decomposition occurs5'* or moderately if the effects of cold work are eliminated without changing significantly the composition of the phase of interest.3,5,6,8 The percentage of oxygen which can be added to Nb-Zr alloys to enhance Jc is limited by the difficulty of subsequent cold drawing. Since Nb-Ti and Ta-Ti alloys in contrast can tolerate appreciably higher percentages of oxygen, it was decided to investigate the superconducting behavior of various alloys in these systems. The present paper describes the results of adding oxygen to a nominal 40 wt pct Nb alloy as a function of thermomechanical treatment. I) EXPERIMENTAL PROCEDURE A small alloy ingot was prepared from high-purity niobium, iodide, crystal-bar titanium, and Nb2O5 powder by arc melting on a water-cooled copper hearth in a gettered argon atmosphere. The ingot was turned and remelted fourteen times to insure homogeneity. After final melting and rapid cooling, it was machined round to 0.415 in. diam, jacketed in stainless steel, and cold-swaged to 0.117 in. diam. The jacket was removed and swaging continued to 0.051 in. diam followed by wire drawing in carbide dies to 0.010 in. diam. Although it was intended that about 1500 ppm O (by weight) be added, inert gas fusion analysis indicated a 2390 ppm 0 content, apparently due to additional oxygen pickup in the arc furnace. Even so, the alloy was sufficiently ductile to be cold-worked to greater than 99.9 pct reduction

Jan 1, 1967

By Sherwin F. Kelly

SINCE we used Chief Buehler's name last year to give our annual report a semblance of respectability, we can follow the good precedent thus established by telling of the work his Missouri State organization has been carrying on, as reported by H. S. McQueen. Considerable value is set upon their magrletorneter working which has covered over 13,000 sq. mi.), for the indications it gives of the major structural features of the region. Numerous geological problems have been tackled Ly resistivity techniques, among which are the locating and outlining of filled sink deposits of sulphides, of iron ore, and of fire clay; tracing of faults and solution channels; mapping of the preglacial structural pattern; measurement of depth of overburden; and

Jan 1, 1937

By H. R. Hanley

THE characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previously in the literature.1 This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors' previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (1) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calcium-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent.

Jan 1, 1931

By R. W. Diamond

THREE mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd:: (1) The Sullivan concentrator, Chapman, B. C. (near Kimberley, B. C.), (2) the St. Eugene concentrator, Moyie, B. C., and (3) the Tadanac (customs) concen-trator, Trail, B. C. Differential flotation is the only concentration method employed in all three plants. Tables are used for pilot work only. Flotation equip-ment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sul-livan concentrator. Successful differential flotation of Sullivan ore com-menced in the spring of 1920, in the pilot concentrator at Trail. During 1920, 193,804 tons were treated by this process. This operation continued without interrup-tion and with steady growth. For the first 7 months of . 1923, which concluded the pilot plant operation, ap-proximately 1100 tons were treated daily. I believe the Sunnyside plant of the United States Smelting &. Refining Co. was the only successful and large scale operation practising differential flotation prior to 1920. in North America. The Sullivan ore, because of its high iron content, was quite a different problem from that at Sunnyside. The entire tonnage of Sullivan ore had to be separated into three sulfide concentrate products-lead concentrate, zinc concentrate and iron concentrate. The choice and arrangement of equipment, and the original flow sheet for the Sullivan concentrator were controlled by the results of the exhaustive pilot mill test. These covered a continuous period of 3 1/2 years and involved the treatment of 1,076,368 tons of Sullivan ore. Satisfactory recoveries are made from feed; 11.0 per cent lead and 7.5 per cent zinc in the form of lead concentrate containing 69 per cent lead, 4.5 per cent zinc, and zinc concentrate containing 3.0 per cent lead and 49 per cent zinc. (The pure zinc mineral in Sulli-van ore is marmatite, 'containing approximately 54.5 per cent zinc and 10 per cent iron. It is apparent, there-fore, that 49 percent concentrate is high grade for this particular ore.)

Jan 8, 1927

By P. G. Shewmon, W. M. Robertson

The derivative of the surface tension with orientation, ??/??, for copper has been measured over the entire unit triangle. This derivative or torque term was determined from the variation of the dihedral angles at the intersection of twin boundaries and free surfaces. High-temperature anneals in graphite with a hydrogen atmosphere gave torque terms of 0.097 at (111), 0.066 at (100), and 0.0257 at (110). A variation from -36oto +23oC in the dew Point of the H2 had no effect on these values, nor did a change from 99.98 to 99.999 pct Pure copper. The removal of graphite from the system decreased ??/?? slightly. Considering the surface near a low-index plane to be smooth except for occasional steps, the free-energy increment per cm of step is calculated, and it is shown that the observed variation of ??/?? is consistent with a random distribution of steps and an interaction energy between steps. Integration of ??/?? gave the relative values of y at (100), (110), and (111) as comPared to ymax: (Y111/Ymax) =0.974, (Y110/Ymax) =0.996, (y100/Ymax) = 0.983. The ratio of the surface tension of coherent twin boundaries to the surface tension of the free surface was found to be (yT/ys) = 0.027 * 0.011. In a crystalline solid the surface tension y (surface free energy per unit area) depends on the orientation of the surface relative to the crystallographic axes of the crystal. Measurements of this variation of y with surface orientation have been reported for metals only within the last few years. Consider the grain boundary groove shown in Fig. 1. Here the three surfaces are all normal to the plane of the paper, and each has a different surface tension, y1, y2, and y3. If the system is at equilibrium, the total surface free energy must remain unchanged for a slight vertical displacement of the intersection (points A, B, and C are kept fixed). As shown by Herring,' the following equation is obtained:

Jan 1, 1962

By L. O. Howard

TWO or three years ago there were submitted to me some reports of tests that had been made on a semi-oxidized ore of silver looking to its treat-ment by combined flotation and cyanidation, together with a sample of the ore, with a request that I check the tests and confirm them, if possible. These tests had been made by a machinery-supply house and with them was a flow-sheet for a proposed mill, with full details of equipment to be used in the mill. The limited data on which this was based at once attracted my attention and have caused me from time to time to put various groups of students at work to develop simpler methods of obtaining data, which it appeared should be at hand and could be obtained by simple tests before attempting to treat these ores commercially. A brief discussion of the working out of such methods may be of interest and may contribute somewhat to the de-velopment of better testing methods for the small operator who has not at his command a staff of metallurgists. Of several tests on samples of varying assay and mineralogical composition, by cyanidation alone, by flotation alone, and, by combinations of the two, the following report was perhaps the most complete and may well serve as a typical example: METALLURGICAL TEST REPORT Silver Mines Co. Semi-oxidized Ore Procedure: Ore ground to 65 mesh, given flotation treat-ment using pine oil and potassium xanthate. Flotation tailing was thickened and given cyaniding agitation in solution strength of 5 lb. cyanide per ton and 2 lb. lime per ton.

Jan 12, 1927

By H. W. Weart, D. J. Mack

SINCE the first recognition of eutectic solidification as the simultaneous formation of 2 solids from one liquid,1 many complex structures thus produced have been observed. Despite many attempts to ascertain it, however, the detailed mechanism by which these structures develop remains obscure. In an attempt to clarify the origin of eutectic structures, the study described in this paper was undertaken. The broad objective of the study was to investigate the effect of different solidification conditions on the structure of single eutectic grains. It was expected that the eutectic structure would thereby be isolated for study, but preliminary experiments revealed another structure within each grain. When a literature surveye revealed only 1 previous mention of the subgrain structure,' it was decided to determine the origin of the structure and to study its response to various growth conditions. Before presenting the details of the investigation, it is apropos to distinguish carefully among the 3 structures produced during eutectic solidification. This is especially desirable in view of the apparent confusion existing in the literature concerning the structures in a eutectic specimen. The confusion is due largely to the existence of the subgrain structure noted above which is easily mistaken for the grain structure. In the following paragraphs, an effort is made to distinguish the 3 structures by briefly describing their origin during solidification, even though the results are thereby anticipated slightly. The 3 structures produced during eutectic solidification are the grain structure, the colony structure, and the eutectic structure, each one contained by the one preceding it. The grain structure is analogous to the polycrystalline structure of a metal or inle-phase alloy in that each grain grows from a single nucleus. A somewhat broader interpretation is needed here, however, because of the presence of 2 phases in each grain. Since in most eutec-tics particles of 1 phase are dispersed in a matrix of the other, a grain may be taken to be the region in which the matrix phase is monocrystalline.*

Jan 1, 1959

By W. A. Anderson, F. N. Rhines, W. A. Johnson

THE rate of the high-temperature oxidation of pure copper has been measured repeatedly by numerous investigators. It appears to be generally agreed: (I) that at constant temperature, after the initial stages of oxidation have been passed and the scale has attained a substantial depth, the film thickness increases in proportion to the square root of the time of oxidation; and (2) that for any given period of oxidation the logarithm of the square of the film thickness is proportional to the reciprocal of the absolute temperature of oxidation.' These relationships are explained upon the basis that the rate of diffusion of copper to the external surface of the film is the controlling factor in establishing the rate of growth. Extensive studies have been devoted also to the mechanism and rates of the early stages of oxidation. There is thus available a reasonably well established theory of the oxidation of pure copper upon which to construct an explanation of the more complex oxidation of copper alloys. Few general principles have as yet emerged from the chaos of observations that have been reported in the field of the oxidation of alloys.2 It is evident, however, that the copper alloys may be divided into two main groups, whose oxidation characteristics are distinguish able. The first group, composed of the alloys with the noble metals, forms substantially pure copper oxide scales; the alloying element is concentrated within the residual metal, and sometimes particles of almost pure noble metal are found in the scales completely surrounded by copper oxide. In the second group, composed of the alloys of copper with the baser metals, the alloying element appears as an oxide in the scale, often in greater concentration than in the alloy itself and sometimes to the exclusion of copper oxide. The oxide scales of the latter class have been found to be made up of one, two, and sometimes more distinguishable layers of which the innermost is often metallic in character, composed of particles of the oxide of the alloying element embedded in essentially pure copper and known as the subscale or zone of internal oxidation. The need for a thorough quantitative study of these modes of oxidation is evident. Since it is apparent that several mechanisms must be cooperating to produce the complex oxide scales found on copper alloys, the analysis of the process into its several simple operations should prove instructive. Fortunately, it is possible experimentally to produce internal oxidation in the absence of an external scale; this permits the isolation and intensive study of one of the steps in the oxidation process. In the present research the rates of internal oxidation of an extensive series of dilute solid solution alloys of copper have been measured and a theory has been developed to predict the observed

Jan 1, 1941