Search Documents

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By M. Maldonado, J. A. Finch

"A flotation bank consists of a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three strategies for optimizing bank performance: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data is analyzed in respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.INTRODUCTION Flotation is used to separate valuable minerals from each other and from gangue. To reach a target metallurgical performance, usually assessed in terms of concentrate grade and recovery, feed is passed through stages such as roughing, cleaning and scavenging. All these stages comprise serial arrangements of flotation cells known as banks, lines or rows. Although a bank is the simplest interconnection of cells in a circuit, i.e. the tails of one cell is the feed to the next cell down the bank, how to operate each flotation cell in a way that the whole bank performance is optimized remains a challenge. Significant efforts have been made towards understanding the effect of operating variables on the flotation performance of an isolated cell (Lynch et al., 1981; Finch and Dobby, 1990; Gorain et al., 1998). However in the case of banks the variables that can be manipulated increase with the number of cells in the bank and the problem of how to manipulate them to achieve optimum performance is difficult even disregarding variation in ore characteristics (Lynch et al., 1981, p. 16). In general, the more manipulated variables available the better for optimization purposes, however without clear guidance how to effectively use them it becomes an “embarrassment of riches”."

Jan 1, 2012

By Wils L. Cooley

This report analyzes electrical accident data in the metal/non-metal mining industry. Accidents are categorized to determine their root causes. Special attention is given to accidents associated with inadequate or defective grounding of mine power systems. Recommendations are made concerning proper grounding practice, especially for dredges and for quarries in hard rock or sand. The costs of instituting the recommended practices are estimated for model mine power systems which are based on field data obtained from 37 mines and several electrical contractors. The expected benefits of various suggested safety practices are also estimated.

Jan 1, 1981

By Bill Tucker, Mike Black

"PROJECT OVERVIEW Crossrail, Europe’s largest construction project, will increase London’s transportation capacity by 10% when it opens in 2018. The Crossrail scheme is a combination of surface and underground railway that stretches 118km east-west through central London from Reading, Berkshire and Heathrow airport in the west to Shenfield, Essex and Abbey Wood in the London Boroughs of Greenwich and Bexley in the east. Crossrail will serve 40 stations, ten of which are new, and bring 1.5 million people within 45 minutes commuting distance of London’s key central business districts. 21km of the Crossrail route comprises twin-tunnels beneath the heart of central London. It is the central section of the route, and the challenges that had to be overcome to construct its tunnels under the historic capital that forms the subject of this paper. The route of the Crossrail tunnels can be seen in Figure 1. These tunnels weave their way through the city’s underground landscape, linking eight new underground stations which connect to the existing London Underground network, providing interchanges with nine existing lines as well as the National Rail and Docklands Light Railway networks.Crossrail began construction of enabling works in May 2009 and launched the first of eight tunnel boring machines (TBMs) in May 2012. 42km of major tunneling work was completed in May 2015, and included 11km of sprayed concrete lined tunnels at the five mined stations (Bond Street, Tottenham Court Road, Farringdon, Liverpool Street and Whitechapel) in addition to the bored tunnel sections. The remaining three sub-surface stations at Paddington, Canary Wharf and Woolwich were constructed as large open boxes prior to the TBMs passing through. Crossrail, Ltd. is a special purpose company formed by the project’s joint sponsors, Transport for London and the Department for Transport, to manage design, construction and commissioning of the project. In 2009, Crossrail engaged Bechtel Ltd. as its delivery partner and a joint venture, Transcend (comprised of CH2M, AECOM and the Nichols Group), as its programme partner. The project is being managed by an integrated programme management team which is staffed by Crossrail and its partners. The railway, when opened, will be operated by Rail for London. With tunneling completed in accordance with the project’s master control schedule, the new railway is scheduled to commence dynamic testing in late 2017, with a phased opening of the tunneled sections and stations through Central London in 2018."

Jan 1, 2016

By P D. Katsabanis

The dynamic tensile strength of geomaterials is known to be highly dependent on the strain rate of the load applied. This is significant in applications where the material is subjected to shock waves and impact loading. This paper proposes the use of a simplified method to determine the dynamic tensile strength of hard brittle rocks using an explosively impacted version of the Hopkinson Pressure Bar. A compressive stress wave was propagated in a sample, representative of the material of interest, by detonating a small charge at one end of a cylindrical sample. The tension wave, generated upon reflection at the free face, causes spalling in brittle materials. Strains at four points in the specimen were continuously measured and the dynamic tensile strength was determined by applying the one-dimensional wave theory.

Jan 1, 2010

By C. G. Dunn, P. K. Koh

The primary recrystallization textures of 11 single crystals cold rolled 70 pct were determined. The effect of crystal orientation on recrystallization behavior was investigated also and found to be large. An exception was found to the relationship that strong components of the recrystolliza-tion texture are rotated from the cold rolled texture by 30° about <110> axes, but generally this relationship was found to hold quite well. Evidence supporting oriented nucleotion was found and discussed in terms of probable active slip systems and <110> edge dislocations. THE present paper is one of a series&apos;.&apos; on recrys-tallization phenomena in cold rolled 31/4 Si-Fe single crystals and is mainly concerned with the textures produced on recrystallizing from stable end orientations. Data for the cold rolled textures of the crystals used have been reported by Koh and Dunn." Their results showed that the sharpness of the cold rolled textures varied throughout the range of stable end orientations and that the tendency to re-crystallize was related to the sharpness of the cold rolled texture, wherein the rate of recrystallization increased and the size of recrystallization grains decreased with decreasing sharpness of the cold rolled texture. In the project under consideration the cold rolled crystals involved a range of initial orientations that, together with those studied earlier,&apos; provide information on several points. The first point is whether the recrystallization texture from a (111) [112] cold rolled texture, a stable end orientation that can be approached from different directions, correlates in any way with the initial orientation before cold rolling, or whether the recrystallization texture is entirely determined by the observable features of the cold rolled texture. The second point involves a preliminary study to see if the main components of the recrystallization textures correlate with the most probable active slip systems. The third point is to determine what effect departure from slip on one slip system has on the tendency to recrystallize. Experimental Procedure Nine specimens from a previous investigation and two additional ones from thicker stock (lot D) but of similar composition to the others were used in the present work. The latter two crystals, like the nine, were cold rolled to a reduction in thickness of 70 pct and the amount of widening was determined. Depending on their primary recrystallization behavior, the cold rolled crystals were given short or long anneals at temperatures of 980°C or higher. Table I summarizes the data on initial orientations, the textures obtained by cold rolling, and the anneals given to provide samples for the present work. Fine grained specimens were thinned to 0.002 in. thickness and placed in an integrating specimen holder. Chart recordings using a transmission X-ray method and MoKa radiation were obtained for diffraction from (110) planes. This method,&apos;,3 which gives data for all of the pole figure except a central region of 30" radius, proved sufficient to give generally five, and sometimes six, of the six possible pole concentration areas of any one component of the texture. These data, therefore, were generally adequate for a positive identification of each component present. The first texture obtained for specimen B-2 was poorly defined because of too coarse a grain structure and therefore too few crystals in each component for satisfactory X-ray reflections. The same

Jan 1, 1957

By Murray W. Hitzman

Two great revolutions in mining occurred during the 20th century. The first took place almost 100 years ago (1903-1905) with Daniel Jackling’s experiment in the economies of scale for large-scale mining at Bingham Canyon. Jackling’s ideas changed the focus of base metal exploration toward lower-grade, high-tonnage deposits. The second revolution was the impact of environmental and social concerns on mining. It started near the end of the 20th century and is still under way. This article speculates on the effects of this second revolution on the future of mineral exploration.

Jan 1, 2005

By Rolf Schillinger

Blasting activities on the surface or underground necessarily involve the most sensitive aspect of environment remediation, human response or annoyance. Such effects are unavoidably characteristic of those activities. For this reason, blasting activities are governed by law and official regulations under surveillance of authorities, where companies and explosives engineers have to proceed within proper limits. Subject of the paper is a practical way of handling some necessary vibration standards being focused on blasting activities. The paper is based on the German Standard DIN 4150, Part 1 - 3, “Vibration in buildings”, Part 1: “Prediction of vibration parameters”, June 2001, Part 2: “Effects on persons in buildings”, June 1999 and Part 3: “Effects on structures”, February 1999.

Jan 1, 2006

By MUSTAFA ERKAYAOGLU, ENVER YILMAZ

Coal is still a part of energy generation worldwide and has a significant role in the sustainable development of countries. The amount of shallow coal deposits is getting scarce, making efficient underground mining operations crucial for both local and global economies. In underground mining operations, longwall mining is a commonly utilized method to extract deep coal deposits. One of the leading engineering goals in longwall mining is increasing the efficiency of the system by investigating the effects of operational factors on equipment. This paper investigates the shearer performance for a longwall top coal caving operation by discrete event simulation that includes modeling the double-drum shearer, belt conveyors, stage loader, and armored face conveyors (AFC) to evaluate system performance by considering the amount of daily coal production of the shearer. As a result, the most influential factor on mine production is determined and a data-based framework is developed. This study suggests a framework for data collection, data analysis, and the interpretation of the operational data to evaluate the primary production unit’s performance. The models developed for the face coal extraction operations in a longwall top coal caving (LTCC) mine have a bi-directional cutting system and can be implemented in other operations readily.

Jul 2, 2021

By M. G. Dellow, D. W. Hendriks

"In early 1988 the decision was made by Noranda Minerals Inc. to install pressure filters at the GECO mill to replace the vacuum disk filters and bunker-C fired rotary kiln dryers. Two filters were installed, one for copper concentrate and one for zinc concentrate. Completion of the project was scheduled for the third quarter of 1989. The filters were made operational in October 1989. Some work remains to be done yet on loadout conveyors for total project completion. Capital expenditures for the project have been approximately $2,700,000 to date. The paper describes the selection criteria for the filter, the installation, startup and associated problems.1. INTRODUCTIONThe filter model chosen for the project was the Verti-Press model VP-50-6(7) (Figures1 ,2 and 3) by Filtra Systems of Farmington Michigan, USA. The decision to purchase the Filtra Systems filter was based on gaining familiarity with a different, mechanically simpler pressure filter than the Larox design and to a lesser extent a necessity for repairs to the the disc filter, rotary kiln dryer system used at the GECO operation for its' copper and zinc concentrates. The fact that it is manufactured in North America was an important consideration. The same basic principles of pressure filtration as the Larox machine are used but the implementation is quite different and somewhat simplified with some interesting innovations. 2 filters were installed to allow direct and immediate comparison of the same machine on both fine and coarse materials. Copper concentrate is reground for cleaning on the flotation circuit while zinc is not. Screen analysis of composited samples of concentrates for 1988 indicated that expected copper concentrate would be approximately 66% minus 400 mesh and zinc 50% minus 400 mesh (Tables 1 & 2).The filter is composed of six horizontal chamber module layered vertically and held together in a frame by 1 O large bolts; torqued down to 4000 ft-lbs. 6 individual belts are used; each with its own drive system. The belts themselves are of a 3 piece design with a filter cloth portion, a support belt and a rubberized intermediate portion. They are held together with steel clipper lacings. A basic description (1) of the filter operation is as follows. ""The horizontal filler chamber is closed by hydraulically pressurizing seals across each end of the filter chamber to 200 psi. The feed pump then pumps slurry into the filter chamber. Suspended solids are retained on the filter belt and the filtered solution drains into a lower drip tray and flows from the filter by gravity. At the end of the filtration or feed cycle, a rubber diaphragm in the filter chamber is pressurized hydraulically to 100 psi pressure. This removes all free liquid from the filter chamber and the filter cake. After the diaphragms are retracted the filter cake is blown with compressed air to remove any residual cake moisture. The seals are then retracted and the belt is advanced to discharge the filter cakes. During the cake discharge the belts are washed with a spray header located at the drive end of the filter. The belt assemblies move one (1) complete revolution during the cake discharge cycle. The cycle automatically repeats until the filter is shut down by the operator."

Jan 1, 1990

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objective and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the following material is presented: (i) review of related literature, (ii) mathematical models to perform quantitative analyses of accident/ injury experience data using the tools and techniques of risk analysis, time series analysis, and the Markov process, and (iii) descriptions of the HDBSEL and ACIM programs which are used to perform accident/injury experience analyses and cost analyses, respectively.

Jan 1, 1993

By Brian Flintoff

"When I was first asked to prepare this paper and presentation in late June, I thought it might be fun to ""step back and paint the bigger picture."" Having attempted to do this, fun is not the first descriptor that now comes to mind, and speaking dyslexically, I've had 'nuf.'Unlike Nostradamus, or even Orwell, I've discovered that I'm ""clairvoyantly challenged"" and not even the psychic hot-line was of much help, at least with respect to process control! I am somewhat comfortable speculating on evolutionary change, but the radical developments that will arise from revolutionary changes are well beyond my mortal capabilities. Even with evolutionary change, I'm reminded of the lessons of time series analysis which show the prediction error to grow exponentially as the horizon moves into the future. As Macluhan is reported to have said: ""Predicting the future based on the past is a little like driving your car while looking in the rearview mirror!""Having honestly presented my qualifications, allow me to try to look at process control and to offer some conjecture on where we're probably headed. In the end, it is said that: ""The plant of the future will have only two employees, a man and a dog. The dog will be there to keep the man from touching the equipment.1""IntroductionA little less than a decade ago Andy Mular and I co-edited a monograph entitled ""A Practical Guide to Process Control in the Minerals Industry."" The work was commissioned by the senior management of a consortium of Canadian mining companies, since it was widely perceived that control was an area of great economic potential, but one that had not been effectively tapped. The concern was that if the industry could not soon deliver on the ""potential"", the term may well have appeared in the epitaph of what was, to these men, a very attractive investment opportunity. I think it is fair to say that over the past few years process control has clearly established itself as an essential technology in plant operation and optimization. That isn't to say that we get it all-right, all-the-time, but, the circumstances are much different than they were. In the eyes of many, process control has attained the distinction of being considered a mature technology, even though there are still countless avenues for exploration."

Jan 1, 1998

The Mineral Industry of Canada in 1951 Continuance of the remarkable, successive increases in the value -of Canada&apos;s mineral production, chief basis of the nation&apos;s post-war expansion, was one of the highlights of Canadian development in 1951, when, according to the preliminary estimate is-sued by the Dominion Bureau of Statistics and reported in the BULLETIN for February, 1952, mineral output for the year reached a new high of $1,228 millions. This marked an increase of 17.5 percent over the previous year, which was the first in which the billion dollar mark had been reached, and an increase of 143.7 per cent over 1946, when production was valued at approximately $503 millions. While higher prices for the principal base metals accounted for a large part of the 1951 increase, quantity gains were made by copper, nickel, zinc, asbestos. lead, cement, and strikingly important. by petroleum, the value of which exceeded for the first time that of coal production. Gold was an exception to the general trend, being lower in both quantity and value than in 1950. For the first time nickel .came within $9 millions of surpassing-gold as the leading mineral product. Metals and Fuels The value of all metals, estimated at $733 millions, was 18.7 per cent more than in the previous year. Nickel advanced 11 per cent in volume and 34 per cent in value. Copper was up 2.4 per cent in quantity and 21 per cent in value, zinc rose 6.6 per cent in quantity and 35 per cent in value, and although the volume of lead produced was lower by 8 per cent, its value increased by 17 per cent. The tonnage of iron ore was 31 per cent higher than in 1950.

Jan 1, 1952

By A B. Christie

Known epithermal deposits in the Coromandel region belong to the low-sulphidation type, represented by three subtypes: (1) andesite-hosted epithermal Au-Ag, (2) rhyolite-hosted epithermal Au-Ag, and (3) andesite-hosted polymetallic veins. Paleo-depths for a range ofdeposits are estimated using various features including: paleo-surface indicators (e.g. sinters), hydrostatic pressures estimated from homogenisation temperature measurements on fluid inclusions, and alteration mineralogy. Paleo-depth estimates to the base of the ore zone for the rhyolite-hosted Coromandel deposits are in the range 200 to 500 m. Andesite-hosted Au-Ag deposits have more variable paleo-depths, and are deeper (up to 950 m) in those deposits with base metals at depth. The majority of Coromandel Au-Ag deposits have limited depth extents (&lt;200 m) of economic grade mineralisation, although Waihi and Karangahake are notable exceptions with depth extents of 575 m and 700 m respectively. Limited depth extents of economic ore are a feature of epithermal systems worldwide and are commonly attributed to gold deposition from boiling fluids. Under hydrostatic conditions in epithermal/geothermal systems, boiling in an up-flowing hydrothermal fluid is controlled by the boiling point for depth (BPD) curve. From fluid inclusion studies of many low-sulphidation epithermal systems, deposition of electrum in economic concentrations appears to be confined to a temperature window of 260 to 180¦C. This means that for dilute, gas-poor fluids that follow the BPD curve, gold deposition is limited to a vertical depth zone of about 400 m, with its upper boundary at about 100 m below the ground surface. The greater depth extent at Waihi and Karangahake, can be explained by mixing of/a deep, hot (300¦C) fluid with cooler (c. 200¦C) heated ground waters. This has the effect of lowering the 260¦C isotherm by up to 300 m, thereby increasing the depth range of economic grade gold deposition within the 260 to 180¦Cwindow of electrum deposition.

Jan 1, 2000

By Richard F. Hewlett

The purpose of this Bureau of Mines paper is to provide the mineral industry with current information on high-speed data processing and to illustrate how some of these techniques can be applied to the industry. The need for applying these techniques is generally recognized, but not much information is readily available on specific applications. This paper briefly describes high-speed data processing and reduction equipment in an effort to familiarize the reader with the functions of the equipment. A list and explanation of some of the possible applications of high-speed data processing for the mineral industry are included. A few of these applications are illustrated by the use of specific examples of existing computer programs or processing methods, including their calculation times and costs. Some of the programs cited herein were developed by the author at the University of Arizona for a Masters thesis in mining engineering. When a reference is made to a specific computer, the reference is given to make the information that is being presented as factual as possible; most of the manufacturer&apos;s equipment that is mentioned in the references was available at the University of Arizona, and no specific endorsement of that manufacturer is intended.

Jan 1, 1962

By Luis W. Pommier

Large quantities of sea sludge containing halogenated organic compounds, such as PCB, oils and metals like arsenic and lead have accumulated throughout the years at the bottom of sea channels and harbors and are obstructing navigation and creating environmental problems which need to be resolved. A sludge from a California port would be dredged by suction pumps, it would be processed in a plant which would be built either on firm soil or on floating platforms. The sludge shows contents of up to 1 ppm of PCB, 15 % oil and 10 ppm of arsenic, which generates a very fetid odor. Bench scale work indicates that most of the contamination concentrates on the solid phase, in fact, only minor amounts of oil report to the sea water and can be readily removed by physical means. After separation of the sea water from the solids of the sludge by decantation, it is possible to solubilize the PCB, the oil and the metals into an organic solvent leaving a non-hazardous soil for disposal near the harbor. The PCB is dehalogenated during the solubilization process leaving a liquor solution containing the oil and metals. The oil is extracted leaving an aqueous solution containing the arsenic. Further process extracts the arsenic from this solution rendering the liquid non-hazardous. Transportation and disposal of the sludge is impractical. There are hundreds of thousands of tons of hazardous soils accumulated in each harbor, which would fill the hazardous waste disposal sites available and it would be, prohibitively expensive to do so. It is not possible to compare the costs of decontamination with a competitive method. If it were, the proposed process would be less expensive than transportation and disposal and it has the advantage of removing the liabilities from the Responsible party. After a full scale continuous pilot project is run to decontaminate a small, 500 cubic yards accumulation of this type of sludge in a California harbor, a full scale environmental project would be initiated. The decontamination of one million tons of sludge would be completed in five years.

Jan 1, 1995

By R. V. Higgins, H. C. Miller

"INTRODUCTION The development of methods for determining the total quantity of crude oil that a given pool could be expected to produce in the future and the well-spacing and drilling programs most likely to result in the recovery of the maximum quantity of oil at the minimum cost became problems of acute concern to American oil producers and petroleum engineers during the second decade of the twentieth century, The United States faced what seemed at that time to be a serious shortage of petroleum, and it appeared that the constantly increasing demand for petroleum and its products could not be adequately supplied. Undrilled prospective acreage, which until then had been plentiful, seemed to be getting scarcer, competition was increasing, the margin of profit to the producer was shrinking, and the need for developing constructive policies of conservation appeared paramount. As a result of physical and economic changes then taking place within the petroleum industry prompted by the seemingly uncertain future, accurate knowledge pertaining to the probable future production of oil wells and of oil lands especially was needed and greatly desired. Furthermore, the need for obtaining the maximum quantity of oil from known fields caused technical information - which up to that time had not been deemed essential to the successful and profitable operation of oil lands - to be sought eagerly. The need for technical information, such as methods for determining future reserves of oil and the rate at which the oil could be obtained under a specific program of drilling, was emphasized further with the passage of the Revenue Act of 1918, and oil producers with enough income to place them in the taxable class were compelled, for the first time, to report their taxable income 4/ to the Treasury Department."

Nov 1, 1939

By Oliver Hall

This paper sketches the mining at Noranda as it would be sketched to a visiting engineer. It does not follow quite the usual form, but is presented somewhat along the lines of a conversation. TO give the mining at Noranda its proper perspective, it is necessary to sketch the whole picture and outline: 1. History 2. Metallurgical Problems 3. Exploration 4. Mining Methods 5. Mining Details 6. Filling 7. Pillar Extraction 8. Costs HISTORY Noranda is a relatively young enterprise, with much of the personal character of its founders woven into it. The name Noranda is an abbreviation of Northern Canada and the name has been a happy one for an enterprise based on northern resources, tenacity and courage. The discovery credit goes to Ed. H. Horne. This intrepid prospector returned again and again to his sulphide discoveries on the shores of Osisko lake and, in 1922, after ten years of prospecting, succeeded in interesting S. C. Thomson and H. W. Chadbourne in his discoveries. The early exploration by L. K. Fletcher, from 1922 to 1925, for Thomson and Chadbourne, indicated promising, but somewhat perplexing, ore conditions. Mr. E. Hibbert and Mr. H. L. Roscoe rook on the task of preparing the mine for production and building a smelter in 1926, and this difficult task in this isolated area made steady progress and the smelter was blown-in in December, 1927.

Jan 1, 1937

By Steve Kral

As the current boom in the global mining industry rumbles on, mining companies have had to step up their efforts to replace mined reserves. Many of the majors are replacing and adding to their reserves and resources through acquisitions. This situation has allowed junior mining and exploration companies to do what they do best. They have been re-examining once uneconomic gold, copper and other metals properties with an eye to partnering with a major to develop them. And mines that have been closed for years due to poor economics are being given another look.

Jan 1, 2006

By Y. M. Chen, H. L. Zhang, W. U. Bing, C. Q. Zhou

Multiphase flow in the widely used Vanyukov furnace was numerically studied. An unsteady three-dimensional and three-phase flow model was firstly built using the computational fluid dynamics (CFD) software ANSYS FLUENT®, and then solved with the volume of fluid (VOF) and k - ??model. The results showed that the proposed model could be used to predict the multiphase movement, the slag/air fluctuation, the vortex formation, and effects of structural and operational parameters. By fast Fourier transform (FFT), the dominant frequency of density with time signal was calculated as 0.29 Hz. The analysis of different injection flow rates of enriched air indicated that this variable has a major effect on the mean slag velocity. The peak mean velocity increased from 2.17 to 4.99 m/s while the flow rate of enriched air varied from 70 to 160 m/s. The proposed model provides a method to optimize the furnace structure and operating conditions for the best furnace performance and lowest energy consumption.

Jan 1, 2015