Search Documents

By Hector Carreon

During fretting, high points or asperities of the mating surfaces adhere to each other and small particles are pulled out, leaving minute, shallow pits and powdery debris. Sometimes these surface conditions are neglected, but they are important in some application such as the aerospace industry. In this research work, non-contacting and contacting thermoelectric power techniques are performed in fretted 7075-T6 and Ti-6Al-4V samples. It has been found that the contacting and non-contacting thermoelectric power measurements are associated directly with the subtle material variations such as work hardening and residual stresses due to plastic deformation produced in the fretting zone but surface topography. Therefore, both techniques could be used for a global characterization of the most relevant fretting induced effects. Potential of these techniques to monitor subsurface changes in other severe surface plastic deformation processes are clearly envisaged.

Jan 1, 2015

By Susumu Okabe

Top blow injection has been applied to continuous copper smelting and converting by Mitsubishi Materials Corporation since 1974. In this process, injected feeds are captured by and dispersed in the molten bath immediately and effectively, and the reaction is enhanced by the agitation of the bath. The continuous motion of the molten bath, however, may cause severe damage of furnace lining materials, if the injection is not controlled and the furnace is not designed properly. In order to suppress refractory wear, especially at the bath line, surface wave of the molten bath should be moderated. A cold model study was carried out with water bath in a cylindrical vessel and the physical model was derived which correlates the oscillation of gas jet impingement on the bath surface and the surface wave. It was found that a half of the proper frequency of the gas jet impingement coincides the proper frequency of the surface wave.

Jan 1, 1998

Gas flow and heat transfer phenomena in two industrial-scale waste-heat boilers of the Outokumpu copper flash smelting process were analyzed with a commercial computational fluid-dynamics (CFD) package Phoenics. Various operating conditions were simulated for the first boiler and particularly for the second boiler. The gas flow pattern was compared qualitatively with the physical laboratory models, and the general flow pattern was consistent with the laboratory visualization. The heat transfer simulation was validated with, temperature measurements for both boilers, and good agreement was reached between the computed temperature profiles and the measured data. The computational results indicate that gas flow in both boilers is of three-dimensional and recirculating nature. The numerical tracer experiments indicate that some dead volume is present in both boilers, and the boiler modification reduced the dead volume from 38% to 15% under basic operating conditions. Radiative heat transfer accounts for 65-90% of the total 'heat transported in the radiation sections of both boilers under different operating conditions. The modified boiler is very efficient for cooling the off-gases at almost doubled volume flow rate. The CFD modeling proved to be a useful tool for numerical experiments and analysis of boiler performance for process: optimization.

Jan 1, 1998

By Alfonso Nájera

Turbulent flow of liquid steel and its control is studied using different geometries of turbulence inhibitors. Four designs of turbulence inhibitors were characterized through experiments of tracer injection I a water model and mathematical simulations using the Reynolds Stress Model (RSM) of turbulence. Geometries included octagonal-regular, octagonal-irregular, pentagonal and squared. A layer of oil was used to model the behaviour of tundish flux during steel flow. Fluid flows in a tundish using these geometries were compared with that in a bare tundish. Experimental and simulation results indicate that the flow in the bare tundish and a tundish using turbulence inhibitors open large areas of oil due to strong shear stresses at the water-oil interface but the squared inhibitor. These phenomena are explained by the high gradient of the dissipation rate of the turbulent kinetic energy using the squared inhibitor. Using this device the kinetic energy reports a high gradient from the tundish floor to the free bath surface as compared with other geometries.

Jan 1, 2006

By F. Qian

An impinging gas jet on a liquid surface is found in many industrial process systems such as electric arc furnace, welding, steel-making operation and others. Fundamental understanding of the interaction of a gas jet on a liquid pool can provide important insights into process behavior resulting in improved efficiency. A numerical model is developed for solving the flow fields of both impinging gas jet region and liquid pool below, in which the deformed interface shape is predicted simultaneously. Using curvilinear coordinates, the Navier-Stokes equations of each phase are solved separately through coupling of static pressure, shear stress and velocity at the interface. Several cases for jet distances and flowrates were investigated both numerically and experimentally with an air-water model. Favorable comparison of numerical results with experimental data confirms the validity of the present numerical approach. An existing phenomenological model for 'penetration depth' prediction was extended for smaller 3et exit height to jet diameter' ratios.

Jan 1, 1995

Novel techniques were developed to obtain samples from and make measurements in the shaft of the flash furnace at the Kalgoorlie Nickel Smelter. The data obtained was used to validate mathematical models of the burners and the reaction shaft. Particle, gas and wall temperatures were measured along with the oxygen potential of the molten particles. Collected particles were characterised by sizing, chemical analysis and optical microscopy. The region of the shaft immediately beneath the burner where the rate of change was most rapid received special attention.

Jan 1, 1993

By Marco Olper

Zinc bearing materials containing chlorides and fluorides of alkali metals, such as EAF dust, Waelz oxides, galvanizing ashes, zinc & brass foundry fumes and converter fumes are little attractive, both technically and economically for processing in ISF plant or in a conventional zinc sulphate electrolysis works. The Ezinexm Process allows for the recovery of high purity zinc in cathode form, from these materials, regenerating the leaching liquor. The process is based on a new electrochemical system which depolarizes the anode reaction with reduction of the cell voltage, compared with the traditional sulphate electrolysis method. The electrolyte, based on a chloroamrnino complex, allows for the recovery of other valued metals present in the zinc bearing materials such as lead, copper and silver, these being recovered as a metallic cement consequently improving the economics of the process.

Jan 1, 1994

By Alex Moyano

The Peirce-Smith converters are traditionally carrying out the converting process of a copper matte in the smelters of Codelco-Chile. However, its production increment is very limited due to the investment magnitude associated to the fulfillment of the environmental regulation. The objective of this paper is to present the Codelco continuous converting process technological advance when converting mattes and/or white metal into blister copper in a Teniente converter unit as an alternative to increment the corporative anode copper production. In 1994, Codelco-Chile started evaluating its ?home made technology? as an alternative to the traditional batch-type converting process. By the year 2001, the Caletones smelter converted liquid white metal to blister copper in a rearranged PS converter continuously. Then, during the 2001-2003 period, several pilot and industrial scale tests were done in a Teniente converter unit at Codelco Norte smelter, evaluating the continuous converting process, i.e., processing liquid mattes (62-68% Cu) to blister copper, demonstrating its technical feasibility with: (i) both constant production of gas flow and SO2 concentration, (ii) production of liquid slag, and (iii) production of a clean blister copper, suitable for the refining process. The promising results have led Codelco-Chile to plan for the 2006 period, a next advanced stage for the continuous converting process evaluation by carrying out a new campaign of tests in a Teniente converter unit at the Codelco Norte smelter.

Jan 1, 2006

By Hebi Yin

A two-dimensional finite element solidification model was developed to simulate the transport phenomena occurring during laser deposition of AISI 410 stainless steel during the Laser Engineered Net Shaping (LENS®) process. The molten pool geometry and the distribution of temperature, solute concentration and velocity were calculated during deposition of a thin wall plate. An analysis of the simulations results revealed the importance of heat transfer by both conduction and convection as well as the roles of the driving forces for convection in the molten pool. The heat transfer and the flow pattern in the molten pool are considerably dependent on the travel speed of the laser beam. For the alloy and process parameters in the simulations, no significant macrosegregation was observed. The temperature-dependent properties and thermodynamic variables involved in solidification modeling were calculated using Thermo-Calc software. The results of this work contribute to the current understanding of transport phenomena in the molten pool of laser deposition processes.

Jan 1, 2008

By Yong .. Jun Wu

Laminated ceramics have received widely scientific and commercial attention because their properties, such as mechanical properties and electrical properties, can be tailored by adjusting the structure, thickness and composition of the different layers. For example, ferroelectric Bi4Ti3O12 (BIT) which has a positive temperature coefficient of dielectric constant (,E) can be used to modify the negative tE of typical microwave dielectric ceramic BaNd2Ti4O12(BNT), However, BaNd2Ti4O12/Bi4TiO12/Bi4Ti3O12/BaNd2Ti4O12 (BNT/BIT/BNT) laminated ceramics could not be prepared by the general method because the optimal sintering temperature of BaNd2Ti4O12 ceramic (around 1350°C) was much higher than that of Bi4Ti3O12 ceramic (around 1100°C). In this research, a new method of spark plasma sintering (SPS) combined with post-sintering was successfully proposed to prepare BNT/BIT/BNT laminated ceramics. It was divided into three steps. In first step, the BaNd2Ti4O12 ceramics were prepared by conventional sintering method. In second step, the calcined and pre-pressed Bi4Ti3O12 powders were sandwiched between BaNd2Ti4O12 ceramic pellets and spark plasma sintered at 900°C for 10min to synthesize BNT/BIT/BNT composite ceramics. In the last step, a post-sintering was employed to reoxidize the partially reduced BNT/BIT/BNT composite ceramics. The results of scanning electron microscopy (SEM) and electron probe microanalysis (EPMA) showed that BNT layer and BIT layer were well bonded and no significant interfacial infiltration between them was observed. The sandwiched BNT/BIT/BNT ceramic with 10.7% BIT in volume has a dielectric constant of 92.85, a low dielectric loss of 01068 and a small temperature coefficient of dielectric constant of 35 ppm/°C at MHz.

Jan 1, 2003

By Jeong-Hwan Kim

The liquid-liquid reactive process (solution process) is often adopted as a synthetic method for precipitated calcium carbonate (PCC) in laboratory studies for its simplicity in operation or ease in controlling process variables. Still, PCC are produced commercially by passing carbon dioxide through a milk of lime, i.e., by a gas-liquid reacting method (carbonation process). Few studies on the carbonation process have been conducted, since the process variables are interrelated and difficult to control compared to the solution process. In this study, both carbonation and solution processes were employed to study the polymorphs of calcium carbonate and growth rate of PCC crystals. The effects of the characteristics of limestone ores as a raw material in the synthetic system of PCC on the synthetic characteristics of PCC were also investigated. To control the nucleation rate in the synthetic systems, the shape factor was considered most important. Single-phase aragonite PCC could be synthesized under a variety of controlled experimental conditions such as ionic strength, solution composition, concentrations of additive ions, and temperature.

Jan 1, 2006

By Takeo Fujino, Nobuaki Sato, Yarong Wang, Kohta Yamada

"Ternary mixed sulfides of some transition metals MTS3 (M=Ba, ·Pb, T=Ti, Zr) were synthesized by a relatively low temperature process using sulfur melt. The mixture of starting materials, such as, metals and/or binary sulfides and a large excess of sulfur was reacted in a vacuum-sealed Pyrex or quartz ampoule at 350- 600 °C for one to three weeks. After the reaction, the remaining sulfur was completely removed by a process composed of filtration of sulfur melt and followed dissolution in CS2• The binary sulfides impurities coexisted in the products were removed by rinsing the products in water and acetone. By using the above method, BaTiS3, PbTiS3 and BaZrS3 'Were obtained in pure form. The effect of addition of halides on the yields of these ternary sulfides were also discussed.IntroductionThere have been a vast number of studies on the preparation and physical and /or chemical properties of mixed metal oxides. As is well known, some of such compounds exhibit excellent materials properties, causing them for use in mechanical, electronic, magnetic and chemical devices. Not a few mixed metal sulfides show similar physico-chemical properties to those of the corresponding mixed metal oxides. However, the study of the mixed sulfide crystals is rather sparse mainly due to difficulties in preparing these compounds. In various methods which have been adopted for preparing mixed sulfides, the simplest method would be the solid-solid reaction of the component binary sulfides or elements. However, there are always diffusional constraints with regard to the reactions in solid phases causing it necessary to heat the reactants at sufficiently high temperatures, viz. 800-1200°C. On the other hand, some mixed sulfides are unstable at high temperatures or to change their materials properties due to sulfur nonstoichiometry and structural modification depending on temperature, i.e., synthesis of such compounds needs to be made at lower temperatures. Processing in alkali halide melts is hopeful to overcome the above problems but to obtain the halide melts the temperatures above ~ 600 °C is needed. Low temperature reaction has been carried out for the preparation of Hg1.24TiS4, which was formed by the ·combination of TiS2 and molten Hg metal at 320°C[l]. Reaction of WS2 with LiBH4 melt at 350°C yielded LixWS2[2]. These sophisticated methods, however, can be applied only to the vary special cases."

Jan 1, 2000

By L. S. Montagna, R. M. C. Santana

"Since the industrial revolution, plastic products sector has growing bigly, however this fact presents as consequence the increase of municipal plastic waste (MPW).The aim of this work is to developmet polymer mixture from MPW with the adittion of rubber tire (TR) post use and to study the mechanical and morphologycal properties. The polymer mixtures Polypropylene/High impact polystyrene/TR (PP/HIPS/TR), where rate weight TR used was 10, 20 and 30 % and with three size particles (500, 710 e 1000 µm). The specimen tests were obtained by injection molding. Preliminary results of mechanical properties showed that the increase of TR influence in a reduction of the flexural and tensile resistance. Results by scanning electronic microscopy on the fracture surface of mixtures PP/HIPS/TR showed a better interaction of TR particle with HIPS than with PP. Also, the presence of microcavoids was observed, characteristic in PP/HIPS blends, favouring in the increase of its opacity.IntroductionOne great part of the municipal solid waste (MSW) is composed of polymer mixed since commodity plastics, blend to polymer composite. The processing of plastics mixtures for recycling has been attempted with some success, but poor mechanical properties and uncertain economic value limit their more versatile reuse. Polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET), poly(vinyl chloride) (PVC) and polystyrene (PS) are among the most common plastic waste, predominantly used in packaging food industry [1].One other problem that preoccupy to the society is the increase of rubber tire waste in the proportion of MSW. In Brazil, from 1999 to 2004, 39 % from 386 mil ton of tire post-use were destined to ciment Industry as source of energy [2]. However this destiny produces one other problem, environment pollution, due to gas mixture emitted.Recycling represents a valid alternative to the disposal of post-consumer plastics in common landfills if it is possible to obtain new materials with good final properties compatible with practical and, above all, by cheap methods [3]The reutilization of group tire rubber (TR) powder as a dispersed elastomeric phase in a thermoplastic matrix offers an opportunity to design second generation materials which would be recyclable due to the thermoplastic matrix and which potentially could present thermoplastic elastomer (TPE)-like mechanical behavior. [4]."

Jan 1, 2008

By Yong Zhao, Yan-hui Sun

Behaviors and evolutions of MgO·Al2O3 in non-oriented silicon steel during calcium treatment were investigated by thermodynamic calculations and high-temperature experiments. MgO·Al2O3 inclusions were the main type of inclusions before calcium treatment, which is also confirmed by the stability diagram of MgO/MgO·Al2O3/Al2O3 from thermodynamic calculations. After calcium treatment, the majority of original MgO·Al2O3 inclusions were mainly modified to CaO-MgO-Al2O3 system inclusions, this would be beneficial to improve castability and product quality of silicon steel. But there was no modification happening to some MgO·Al2O3 spinels which were directly surrounded by CaS inclusions. The content of Al2O3 occasionally existed a sudden increase besides a common decrease in the product layer of CaO·MgO·Al2O3. Then the evolution mechanisms of MgO·Al2O3 inclusions were proposed in present work. Thus, Al/Mg atom ratio had a significant influence on the modification of MgO·Al2O3 spinel.

Jan 1, 2016

By Pertti Koukkari, Nagendra Tripathi, Karri Penttilä, Justin Salminen

A computational fluid dynamic model for a novel flash ironmaking process based on the direct gaseous reduction of iron oxide concentrates is presented. The model solves the threedimensional governing equations including both gas-phase and gas-solid reaction kinetics. The turbulence-chemistry interaction in the gas-phase is modeled by the eddy dissipation concept incorporating chemical kinetics. The particle cloud model is used to track the particle phase in a Lagrangian framework. A nucleation and growth kinetics rate expression is adopted to calculate the reduction rate of magnetite concentrate particles. Benchmark experiments reported in the literature for a nonreacting swirling gas jet and a nonpremixed hydrogen jet flame were simulated for validation. The model predictions showed good agreement with measurements in terms of gas velocity, gas temperature and species concentrations. The relevance of the computational model for the analysis of a bench reactor operation and the design of an industrialpilot plant is discussed.

Jan 1, 2014

By S. Sundarraj

The morphological transition between columnar and equiaxed structures is an important solidification phenomenon frequently observed in castings, especially complex parts with varying cross-section, The mechanical properties and the occurrence of defects such as hot tears are strongly dependent on the structure formed in the casting. Hence, it is important to understand the conditions leading to columnar or equiaxed structures. Although extensive work has been done in modeling solidification systems, almost all of the existing models are based on the assumption that the structure formed in the casting is either purely columnar or purely equiaxed. Prediction of the columnar-equiaxed transition (CET) requires a solidification model which accounts for the formation of both columnar and equiaxed structures, along with related microscopic and macroscopic solidification phenomena. In this paper a CET model is presented which: (i) takes account of both columnar and equiaxed structures, (ii) accounts for macroscopic heat transfer coupled with microscopic phenomena such as nucleation, growth and microsegregation, (iii) satisfies solute conservation, and (iv) is easy to implement in commercial finite element and finite difference software. The proposed model predictions of CET have been validated with available experimental results for a uni-directional solidification of an aluminum-copper alloy. A sensitivity analysis has also been carried out to determine the effects of various parameters on the CET model predictions. The model is being extended to other alloy systems and more complex geometries. This work will be published in due course.

Jan 1, 1996

By J. E. Dutrizac

Mineralogical studies were carried out on nodulated copper cathodes from three primary refineries to characterize the nodular growths and to elucidate the causes of the nodulation. Nodulation is often initiated at the surface of the starter sheet or the stainless steel plating blank, although a layer of smooth copper sometimes is deposited before nodulation commences. In some instances, the "roots" of the nodules exhibit a pronounced dendritic texture that is associated with an abundance of cavities. Slimes particles are not usually associated with these growth features which lead to a globular surface deposit. The globules sometimes develop into larger nodules, and this type of nodulation is likely caused by improper addition agent concentrations. The nodules on most cathodes, however, exhibit "roots" at the contact with the substrate that are associated with microcavities and large clusters (>40 µm) of slimes particles. The slimes constituents are commonly Ag powder, PbSO4 and Cu2(Se,Te) but not AgCu(Se,Te) or Ag,(Se,Te). The size of the slimes clusters, rather than their composition, appears to be the important factor causing the copper to grow into nodules. Tiny individual slimes particles themselves do not appear to cause cathode nodulation.

Jan 1, 1999

By J. L. Hill, M. A. R. Sharif, J. Lin

"A numerical algorithm has been developed to simulate the movement, breakup, and entrapment of the oxide film inclusions encountered during the mold-filling processes of aluminum castings. The flowfield is solved using the well-known Marker and Cell (MAC) method by a time marching process. The Volume of Fluid (VOF) method is used to track the free surface boundaries. A kinematic approach is employed to track the movement and breakup of the oxide films on the free surface or in the bulk liquid metal. The computer program based on the proposed algorithm is able to model the flow behavior and oxide film movement, breakup, and entrapment in mold cavities for aluminum castings.IntroductionMetallographic and fractographic studies of the aluminum castings show tangled networks of oxide films in the castings. These oxide films can form in the furnaces or during the mold filling processes. Green and Campbell [I] concluded that the oxide film defects dominate the strength of aluminum castings. The main cause of oxide film entrapment into the bulk molten metal during the casting processes is the surface turbulence. In film-forming alloys, if the surface breaks, due to a drop, a fountain, or a breaking wave, then the surface film is folded over and incorporated into the bulk liquid. The incorporation of surface films leads to cracks in the casting and other defects that are nucleated by the presence of the folded films, such as porosity and hot tears. Campbell [2] estimated that up to 80% of scrap in light-alloy casting is the result of surface turbulence."

Jan 1, 1999

By Yin Zhang, Xiaoyu Huang, Mi Wang, Bencheng Du, Youduo He

"Burners are important facilities for blast furnace stoves to raise hot-blast temperature up to 1200°C. Common types of two-ring ceramic burners have very long flames so that part of combustion occurs in the upper part of the chequers and will cause damage to the refractory materials. Using computer simulation to analyze the turbulent diffusion flame in the combustion chamber, some good results were obtained. A new type of ceramic burner will be installed by Anshan Steel Complex in stoves of blast furnace number 4. A pilot experiment was done on the new burner. The experimental data have shown that the mixing condition was improved and the length of flame was shorter with the new type of ceramic burner.IntroductionPulverized-coal injection can give significant operating saving, reducing coke rate in blast furnace(BF) operation. However, during high rates of coal injection, extra heat must be compensated in hearth to maintain certain raceway adiabatic flame temperature. One of the effective methods for heat compensation is to raise hot-blast (HB) temperature up to 1200°C. Nowadays, since the fuel being combusted in stoves is BF gas only, in which the calorific value is down to round 3000 kJ/m3 , to increase the combustion ability and to provide a suitable length of flame in combustion chambers of stoves becomes more important. In other words, designing a good ceramic burner which will affect to HB temperature and stove lifetime is drawing more attention."

Jan 1, 1999

By Godwin M. Beene

Large scale mining operations started in Zambia in 1913 and rapidly expanded during the post 1930 period with the opening of several mining and processing plants on the present Zambian Copperbelt. As a consequence of poor tailings dumps design methods at the start of the mines, and in view of stringent Government Legislation pertaining to environment in the recent years, Nkana Mine has developed a unique method of dump construction at its current tailings depository, Tailings Dam 15A. This method has enabled the revegetation of the dump retaining walls while construction is still in progress, a situation which was not possible on the older dumps. Cowdung has proved to be a superior fertilizer for providing plant nutrients on the tailings. The new method of dump walls construction and walls rainwater runoff drainage system has almost eliminated tendency of gully formation which is common on older dumps, as rainfall on the Zambian Copperbelt comes in intense thunderstorms. The decanted water from the dump is discharged to the natural environment in a controlled fashion after ensuring that it meets the Zambian Government Statutory requirements.

Jan 1, 1999