Search Documents

By G. A. Irona

Solids injection into non-ferrous converters and furnaces is becoming increasingly important for concentrate injection, removal of impurities, and recycling of dusts and other waste materials. The fundamental design aspects of these technologies will be reviewed, including gas and particle trajectories, lance clogging, heat transfer, and mass transfer including reaction rates and mixing. The use of soda ash for removal of impurities such as antimony and selenium will be used as an example of versatility of powder injection processes.

Jan 1, 1993

By Sungdon Kim, Chuljoo Kim, Joonsoo Kim, Hosung Yoon

"This study was performed to establish the optimum leaching condition through the experiments for the oxidized roasting followed by leaching of fluorocarbonate rare earth mineral (bastnasite) using sulfuric acid, and to establish the optimum condition for the recovery of cerium by ion- sieve method from the leached solution of bastnasite. The optimum conditions for the sulfuric acid leaching by the oxidizing roasting of bastnasite concentrates are that the roasting temperature is 550 -600 °C, the roasting time is 2 hrs, the concentration of sulfuric acid is 6N, the leaching temperature is S0°C and the leaching time is 3 hrs. At this time, the leaching yield of total rare earth oxides in the leaching of bastnasite concentrates is about 91%. When cerium is recovered by ion-sieve method from the solution obtained by the sulfuric acid leaching of the roasted bastnasite, the optimum conditions are that the TREO(total rare earth oxide) of leached solution is below 70 g/l, the flow rate of leached solution is 9.6 ml/min and the ratio of height to diameter of resin packed in column is above 9. In these conditions, the recovery of cerium of yield 85% and purity 96% is possible.IntroductionThe rare earths are generally called to Lanthanides, which are totally 17 elements including Scandium of atomic number 21 and Yttrium of atomic number 39 in addition to 1 S elements from Lanthanum of atomic number 57 to Lutetium of atomic number 71. Since the separation to each element is very difficult because of their similar chemical properties, the rare earths were used as the mixed rare earths and the mischmetal without separating to each element. However, the high purity rare earths are recently produced commercially to each element so that they are used as the materials for high tech. industry such as electric and electronic materials, catalysts, optical materials, special alloy and 8Uperconductive materials, and their consumption is rapidly increasing. Therefore, the purpose of this study is firstly to prepare leached solution by using the series of process of the oxidation-roasting and leaching by sulfuric acid. Next, second purpose is the separation and recovery of cerium by ion-sieve method."

Jan 1, 1998

By Dumitru Mitrica, Vasile Soare, Elvira Alexandrescu, Mihai Ghita, Marian Burada, Petru Moldovan, Raluca Maria Florea

"Aluminum metal matrix composite Al-Si /SiCp was prepared by reactive gas injection and subsequent remelting. The influence of the remelting process on the microstructure and physicalmechanical properties of the resulted material was investigated. Samples resulted from the synthesis process contained silicon carbide agglomerations in the vicinity of primary silicon and large pore concentrations. In-situ formed silicon carbide presented mostly a polymorphic structure with particle sizes varying from 1 to lOµm. Physical and mechanical properties were largely influenced by the porosity distribution. The remelting process provided a decrease in the composite material porosity and pore size, with significant improvements in the particle distribution and physical-mechanical properties of the composite material. Additions of up to lwt.%Mg in the starting alloy improved the in-situ carbide formation and particles distribution in the solidified material. However, stable and large particle agglomerations were detected in the material in absence of conventional stirring or controlled solidification techniques.IntroductionThe remarkable properties of composite materials (yield strength, stiffuess, hardness and resilience at a reduced specific weight) make them attractive for applications in automotive, aerospace and military industries. Particle reinforced aluminum metal matrix composites (PAMMC) are known for their high strength to weight ratio. The recent development of P AMMC created the possibility to obtain large particles concentrations, exceeding 10% by volume ofreinforcement (SiC, AIN, Al203, etc.). The improvement ofhigh temperature strength and wear resistance made them appropriate for the use in automotive applications, such as the pistons, rotors, disc brakes, and propeller shafts [ 1]. The present main disadvantage of the P AMMCs is their high costs for obtaining and processing related to the final product performance. In order to benefit from the advantages that offer composite materials properties a reasonable production cost - performance ratio must be obtained [2]. Recent innovations in the manufacturing of aluminum-based metal matrix composites provided notable performance improvements but no feasible solutions were found for lowering their present high prices."

Jan 1, 2014

By Bo Jiang, Jiusan Xiao, Hongmin Zhu, Kai Huang, Shuqiang Jiao

Carbothermal selective reduction of simulative titanium slag and various titanium raw materials were presented and SiO2 was found to be partially reduced, forming a series of Fe-Si alloys during the process. Thermodynamic analysis of the selective reduction between TiO2 and SiO2 was performed using HSC 6.0 software, then a series of equilibrium experiments were designed and presented. The activity of Si reduced from SiO2 was affected by the presence of Fe reduced from FeOx and the generation of Fe-Si alloys, promoting the reduction of SiO2 in the whole process. The results of experiment are in great accordance with the calculated data obtained from thermodynamic analysis.

Jan 1, 2016

By D. Y. Wang, G. Y. Sha, X. L. Shen, D. R. Gu

The study of the volatilization kinetics of zinc and lead in pellets made of zinc-leadbearing dust mixed with coal powder, in a nitrogen atmosphere and at a temperature range between 1100 °C and 1300 °C, shows that the reduction temperature has a significant effect on the volatilization rates of zinc and lead, and that both the particle size of the coal powder and the extra carbon content has no effect on the volatilization rates. The obtained activation energies for the volatilization of zinc and lead are 79.42kJ/mol and 88.74kJ/mol respectively. The volatilization rate of zinc is controlled by the reaction between the zinc oxide and carbon monoxide while that of lead is controlled by the lead evaporation reaction, and the diffusion of gaseous lead through the gas boundary layer covering the surface of the reduced liquid lead.

Jan 1, 2000

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-Al intermetallic compounds were transformed into Mn-Fe-Si-Al and Mn-Fe-Al compounds by the addition of manganese into molten aluminum. In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnA4 and FeMnAI6 are paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By Rodney J. Ishak

The reduction of Mn3O4 to MnO has been investigated in a thermobalance apparatus. The charge was composed of manganese ore (decomposed by heating/calcination or pre-reduction to mainly Mn304) and coke. The material was charged to a crucible, which was suspended in the balance. CO-gas was distributed through a grid in the bottom of the crucible. Two sizes of ores were used; 2.4-4.8 mm and 6.7-9.5 mm. Coke particles were in the size range 4.8-6.7 mm. Experiments were conducted in the 900-1100°C temperature range. The composition of the product gas was monitored continuously. External mass transport between bulk gas and particle surface does not seem to limit the rate of reduction. Assuming that both diffusion through product layer and chemical reaction at the interface between MnO and Mn304 are rate controlling, the data was tried both in a shrinking core model and in a grain model using regression. The grain model gives the best physical description of the process, because the reactant is in fact a porous medium. With this model the effective diffusivity was calculated to be in the 1.5-6.10-5 m2/s range. The pore size was mainly between 0.1 and 10 um.

Jan 1, 2003

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuOQs) increased with increasing slag basicity, defined by Xcao /XSiO, The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By Kim Verbeken, Evelien Van de Steene, Marc Verhaege, Jeriffa De Clercq

"AbstractThe industry is confronted with stricter discharge levels and an increasing awareness to avoid toxic waste (such as heavy metal containing sludge obtained in physicochemical water treatment) and recover valuable metals. This can be realized by ion exchange or by electrodeposition. Both techniques however show an optimum concentration range to efficiently remove and/or recover metals: electrolysis can recover the metal in its metallic form but suffers from low efficiency when applied to diluted solutions, whereas ion exchange can only be applied economically in the low ppm range.A combination of ion exchange followed by electrodeposition was applied to an industrial wastewater. The strong acidic ion exchange resin was stripped with H2SO4 giving a solution of 9g/L nickel. From this solution, nickel was electrodeposited in an ammonia buffer on a Ti-mesh cathode with high current efficiency. It is shown that organic compounds (surfactants, brighteners, …) present in the industrial wastewater do not influence the recovery process.IntroductionAlmost all rinse waters emerging from metal plating plants are generated during the washing operation of plated materials. These solutions with low metal content must either be recycled within the process or be discarded to the surface water after decreasing their metal content to acceptable levels determined by the local environmental regulations, which become more and more stringent. Today, the most commonly used practice is a physico-chemical treatment (precipitation) and a resin post treatment to meet the standards. A more sustainable approach should use a technology to recover efficiently the metal or metal salt without the production of sludge and the effluent should be consistent with environmental regulations."

Jan 1, 2008

By Isıl Kerti, Sibel Daglılar, Sinem Yıldırım

In this study, effect of rolling and coiling temperature in thermo mechanical controlled process (TMCP), on the microstructure and mechanical properties of dual phase (DP) steel according to martensite volume fraction (MVF) rate was investigated. By using various finishing mill exit temperature and cooling conditions that is controlled laminar cooling system, the microstructural evolution of coil improves the mechanical properties with lower costs and higher productivities, in comparison to the heat treatment after rolling. The main part of the paper contains the result of tensile, yield and microstructure properties of DP600 steel produced on hot strip rolling plant and run- out table line. The results show that a higher MVF and an increasing cooling rate after the last deformation raised strength of the DP600 steel. The yield strength and ultimate tensile strength increase by decreasing coiling temperature.

Jan 1, 2015

By S. Yuan

Oxygen ion conducting yttria-stabilized zirconia (YSZ) tube was used to remove oxygen from molten Cu at 1373K. Outer surface of the tube was in contact with the melt and the inner surface containing a thin layer of porous Ni-ZrO2 cermet electrode was in contact with a reducing gas. The migration of oxygen species (O2-) from the Cu melt through the YSZ tube is accompanied by an equal and opposite flux of electrons maintaining electroneutrality. Without applying an external EMF, the fluxes are maximized by short circuiting the melt with the cermet electrode. For efficient oxygen removal, the YSZ tube must be thin, contact resistances should be negligible, and the electrodes must be porous and cover the entire electrolyte surface for charge transfer. This refining process is environmentally sound, can use reducing gases such as H2, CH4 and CO without running the risk of increasing H or C content of the melt.

Jan 1, 1993

By Qingchun Yu, Bin Yang, Yong Deng, Heng Xiong, Fei Wang, Minxiu Chen

"Metal aluminum produced by non-electrolysis process received much attention due to its lower energy consumption. In this paper, carbothermic reduction and carbothermic-chlorination of alumina in normal pressure and vacuum were studied. The products were examined by means of XRD, EDS and SEM. During the carbothermic reduction process using carbon reductant in normal pressure, no metal aluminum was found. However, when coal was used as reductant, a mixture containing metallic aluminum, A14C3, and silicon was obtained, but metallic aluminum couldn't be separated from the mixture. During the carbothermic-chlorination process in vacuum, Al404C and Al4C3 were produced by the reaction between alumina and carbon, and Al Ch gas reacted with Al404C and Al4C3 to produce Al Cl gas. Metallic aluminum was produced due to the disproportionation of A!Cl gas and condensed on the collecting plate. Meanwhile, the initial temperature of carbothermic reduction of alumina reduced in vacuum compared with that in normal pressure.IntroductionIndustrial production of primary aluminum is carried out in alumina cell by the so-called Hall- Heroult process, necessitating the use of very high currents of low voltage. The alumina from which metallic aluminum is gained must be chemically pure, otherwise impure metal results. The main drawbacks of the electrolytic production are its very high energy consumption, the release ofperfluorocarbons, and the high specific C02 emissions [1]. During the past years, there were a lot of attempts to produce metallic aluminum by carbothermic reduction of A1203 [2, 3]. Cox [4] determined the vapor pressure over the A1203-C system and performed X-ray diffraction analysis of condensed products. It was demonstrated that an increase in the carbon content in the system leaded to the sequence of transitions: A1203~Al404C~A1zoc~A14C3 ~AI [5]. In any carbothermic reduction process for aluminum, extremely high temperatures (2000 °C ) were required [6]. In spite of considerable effort, the carbothermic reduction of alumina to aluminum remains a formidable technical challenge, due to the high temperatures required, and to the formation of aluminum carbide and oxycarbide byproducts [7]."

Jan 1, 2013

By M. Cavallini, G. Cannavale, P. P. Milella, A. Pescetelli, C. Lupi

Ni-Cd sealed and vented cells have been widely used in the last few years. The environmental hazard related to the heavy metals contained in Ni-Cd batteries is well known. Therefore, a number of scientific studies and commercial processes have been implemented in order to recycle them. Since spent batteries are a heterogeneous and complex material, any kind of recovery process needs some preliminary treatments. The proposed process described in this paper has been tested in laboratory and further developed in a pilot plant. It consists of a combination of mechanical and hydrometallurgical treatment steps, and is able to treat all type of Ni-Cd batteries. In particular, the mechanical treatments have to be done separately on vented and sealed cells, while the hydrometallurgical step is performed on a mixture of the two products obtained from mechanical steps. A fully automated dismantling line would allow the separate recovery of the plastic or metallic casing, terminals, KOH electrolyte, and electrodes to be further processed· for Ni and Cd recovery. The electrodes coming from dismantling line and sealed batteries are submitted separately to an original crushing and elutriation treatment to separate metallic and active paste in the first case and metallic, plastic and active paste in the second case. The hydrometallurgical treatment is carried out on active paste bearing product to produce Ni, Cd, and Fe comn1ercial salts through acidic leaching followed by a multi-step solvent extraction operation to obtain pure solutions.

Jan 1, 2000

By Nagahiro Saito, Takahiro Ishizaki, Daisuke Yata, Akio Fuwa

"Ternary compound-semiconductor, CuInTe2, film was deposited cathodically under potentiostatic conditions on titanium substrate from aqueous solution containing CuCl2, InCl3, TeO and HCI in this study.The deposition parameters such as electrolytic solution composition, potential and temperature were optimized· for electrodeposition of CulnTe2. Structural characterization of the: deposited film was also carried out using XRD and SEM. Electrodeposited films Were prepared and analyzed for their chemical composition using ICP. The ICP analyses showed that the stoichiometry of the films could be controlled by (1) the deposition potential and/or by (2) the electrolytic bath composition.1. IntroductionThe ternary chalcopyrite type compound semiconductors exhibit such electrical, chemical and optical properties that make them promising for photovoltaic devices (Kazmerski and Wagner 1985)(1). Many researches have been devoted to the characterization of these materials for over one and a half decades. High efficiency solar cells based on p-CulnSe2/n-CdS have been reported (Mickelson and Chen 1983)(2).The electrodeposited fil ns of semiconductors have more advantage than other physical and chemical deposition techniques; it is relatively easy and economic technique and the semiconducting properties such as band-gap variation, concentration of dopant stoichiometric composition and so on can be controlled with some accuracy. The electrodepositions of the ternary CuInS2, CulnSe2 have been reported by many workers (Hodes and Cahen 1986, Bhattachaya 1983, Singh et al 1986, Lokhande and can be prepared as both p-type and n-type. Therefore, its potential for application in optical and photovoltaic devices is one of the great interests. Bhattacharaya and Rajeshwar (1986)(9) reported the electrodeposition of CuInTe2 from an acidic bath· on indium tin oxide (ITO) and Mo substrate. Triethanolamine (TEA) was used as a complexing agent for indium. The electrodeposited CuInTe2 films were non-stoichiometric in composition under all their experimental conditions by electron-probe micro analysis (EPMA) and Auger depth profile analysis. In this paper, we report our results on the behavior .of Cu-In-Te electrodeposition from ·acidic baths; the preparation of CulnTe2 and the effect of bath composition on electrodeposited films obtained."

Jan 1, 2000

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Kellie Provazi

"The purpose of this paper is to study metal separation and recovery from a sample composed of a mixture of the spent household batteries main types, using liquid-liquid extraction and metals electroplating. The electrolytes preparation consisted: grinding the waste of mixed batteries, reduction and volatile metals elimination using electric furnace and acid leaching. From this solution were studied the liquid-liquid extraction using Cyanex 272 [bis(2,4,4-trimethylpentyl) phosphoric acid] with tributyl phosphate as extracting agent. After study of solvent extraction and stripping has been recover and separate the metallic ions and with electroplating was recovered the manganese, copper, nickel and cobalt in their metallic forms.IntroductionCurrently has increased the consumption of electronics devices such as mobile phones, laptops, wireless phones, comcorders, etc., especially portable devices that use batteries as a power source, and consequently has increased the disposal of such material.Increased consumption of this devices is caused by several factors including increased popularity of consumer electronics devices, has become essential of modem life. Therefore, recycling of batteries is important because its reduces the waste of raw materias and nonrenewable resouces used in manufacturing these materias and help prevent potential environmental risks associated with improper disposal of these products together with household garbage.The batteries have a very diverse composition, containing metals such as zinc, lithium, nickel, lead, mercury, cobalt, cadmium, iron, copper, manganese and rare earths. Some components may contain hazardous materials such as cadmium, mercury and lead, and can contain acids or bases.This research line is a pioneer in dealing with a single process for recycling a mixture with all batteries types, for only processes that exist in the world are based on the recycling a mixture with all types of batteries, for only processes that exist in the world are based on the recycling of one or two types of batteries [1-4]. This process necessitates the previous separation of the batteries by type."

Jan 1, 2012

By Tsutomu Yamamura

The electrolytic reduction mechanism of rare-earth chlorides such as LaCl3, CeCl3, NdCl3, ` SmCl3 and DyCl3 in alkali chloride baths has been investigated in NaCl, KCI and eutectic LiCI- KCI by means of electrochemical transient methods. The thermodynamic behaviors of rare-earth containing species have been discussed in the frame of Electrode potential - P02- diagram. Low current efficiency found in the case of Nd electro-winning has been attributed to the dissolution of Nd into the bath. The analyses of electrochemical measurement required the elucidation of the effects of the factors such as under-potential deposition, metal dissolution, moisture and oxygen partial pressure.

Jan 1, 2003

By Wenjie Zhu

Hexavalent chromium is a widespread environmental contaminant. An Achromobacter sp. strain nominated Ch1 can reduce soluble and toxic chromate to insoluble and non toxic Cr(III) in aerobic cultures, and no Cr(VI) decrease was observed in anaerobic cultures. In contrast with other Cr(VI) reducing microorganisms, Ch1 showed higher Cr(VI) reduction at high pH. Reduction performed under alkaline conditions at pH 7 to 11, and the optimal pH was 10. During the reduction, pH decrease was observed may caused by production of acidic metabolic byproducts from aerobic respiration. In the present study, the ability of Achromobacter sp. Ch1 to reduce Cr(VI) during growth was evaluated with lactate as an electron donor. In NB medium, Ch1 reduced 100% of 24mM of Cr(VI) in 35h, but only 73% of 30mM of Cr(VI) after 48h of inoculation. Reduction was inhibited by metal ions like Ag+, Cu2+, Zn2+, slightly inhibited by Mn2+, and not affected by Mg2+. Results revealed that reduction rate of Cr(VI) also increased with the increasing of concentrations of lactate, and complete reduction was achieved at the concentrations above 40 mM. HPLC analysis demonstrated Cr(VI) reduction was associated with the consumption of lactate. There was a large quantity of dark blue sediment generated in the culture during Cr(VI) reduction by Ch1. Energy dispersive X-ray (EDX) analysis showed that the major element composed the formed sediment was chromium presented as Cr(OH)3 precipitate. The features characterizing Cr(VI) reduction by Achromobacter sp. Ch1 are high Cr(VI) concentrations and high pH.

Jan 1, 2006

By Alessandro Blasi, Massimo Morgana, Corradino Sposato, Pietro Garzone, Giuseppe Devincenzis

The rare earth elements are essential for a diverse and expanding array of high-technology applications, which constitute an important part of the industrial economy of the 21st century. As a matter of fact, rare earth has been listed in the category of strategic elements in many countries becoming a core business for international research. Experimental tests have been carried out on a bench scale battery of mixer settler composed of 24 stages, each one with a volume of 150 ml. These trials have been performed at room temperature checked by a micro-climatic control system. The battery was setted in two sections: extraction and scrubbing section. Rare earths concentrations were obtained by ICP-OES analysis made on aqueous phase and on the stripped from organic phase. We obtained a complete separation of light rare earth (La, Ce, Pr, Nd) in two sub-groups: La/Ce and Pr/Nd.

Jan 1, 2014

By Ricardo Melamed

Metallic mercury has been extensively used for gold recovery. Although the solubility and mobility of metallic mercury is low, this metal can undergo many transformations, leading to mercury contamination in humans. The complexity of Hg chemistry in the environment reflects its different possible oxidation states and species, with different physical-chemical properties. The interaction of Hg in the terrestrial system, as well as in the aquatic environment, is important to understand the mercury cycle. This paper reports data on the adsorption of Hg onto an Oxisol soil. Results show that the interaction of Hg(II) at the soil-solution interface depends strongly on ligand concentration in solution, which can affect Hg mobility. The presence of the chloride anion in solution increases the mobility of Hg(II) through the soil, due to a relative lower affmity of mercury chloride at the oxide surface. In the absence of chloride, Hg(II) form strong complexes with the surface, and its adsorption behaviour is similar to the adsorption of other hydrolizable cations.

Jan 1, 1996

By P. Koskinen

Outokumpu Oy has 30 years' experience in nickel production. It is mainly based on the technology developed within the company. The production chain starts from the mines reaching to the high-grade cathode nickel and the stainless steel manufacturing. As a multi-metal producer Outokumpu has the advantage to exploit from nickel raw materials also other valuable metals and intermediate products which can be processed at the company's various plants. The main source of nickel concentrate is nowadays the Enonkoski Mine started up in early 1986. It is the most modern mine in Finland being provided with the latest Finnish high-tech systems. Nickel concentrates are smelted at the Harjavalta Works using Outokumpu's internationally well-known flash smelting method. Also nickel containing residues and secondaries' are used as raw materials. The high-grade nickel matte from the smelter is then refined at the nickel refinery in a hydrometallurgical process, which was also developed by the company's own research staff. These processes have been continually improved and capacities gradually enlarged to 18 000 mtpy of cathode nickel. Besides plating, melting and superalloying purposes part of the nickel ends in stainless steel at the Tornio Works. The production was started in 1976 and has reached an established position on the European market.

Jan 1, 1988