Search Documents

By S. D. Van Nort

The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc., an 81% owned subsidiary of Freeport-McMoRan Inc., lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in early 1988. Production at the open pit Grasberg deposit commenced in December 1989. The Grasberg copper-gold orebody is contained with a young igneous complex of dioritic composition which intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork.

Jan 1, 1991

By Michael Schultz, Gregory Sanders

In 2017, the North Texas Municipal Water District (NTMWD) initiated the design of the Sister Grove Regional Water Resource Recovery Facility (SGRWRRF) to provide additional treatment capacity for future population growth within the Lavon Lake watershed. To provide a discharge location for SGRWRRF approximately 4.5 miles of 2.4- meter (96-inch) internal diameter pipeline will be constructed, including 2.3-kilometer (7,800) feet and 487-meter (1,600 foot) long tunnel segments. This paper will discuss the anticipated geology of the two tunnel segments, selection of the tunnel alignment, the anticipated initial tunnel support requirements and other aspects of the project design

Jun 13, 2021

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector is one of the leading sectors where work accidents are most intense because of the constant change of work environment and heavy working conditions. The losses and the halt of production after the accident negatively affect productivity and production efficiency. It has been found that there are very few studies on the use of Data Envelopment Analysis (DEA), which is one of the nonparametric efficiency analysis methods, in the evaluation of mining sector occupational accidents. According to parametric activity measurement methods, it has been tried to show that the DEA can also offer the opportunity to interpret work accidents by taking advantage of its advantages. Due to the application of open-pit mining methods along with underground working techniques which increase the risk factors with respect to accidents at work that occurred between 2012 and 2018 of Western Lignite Corporation (WLC) were tried to be analyzed in the present work. As a result of the analytical work using Data Envelopment Analysis (DEA) for the years 2014, 2015, 2016, 2017, and 2018, inefficiency has been determined in both underground and surface operations. According to the results obtained, it was determined that WLC could not produce enough production in both the underground and surface coal mining operation, despite the accidents that occurred, while it had the opportunity to produce more. In addition, it was found that the increase in accidents occurred more than the increase in the amount of production during the years studied.

Jul 4, 2021

By Ryne Goodnough

INTRODUCTION The Wyodak Mine is located in the northern Powder River Basin of Wyoming and is thought to be the oldest continuously operating coal mine in the United States, having recorded yearly production since 1923. The mine has expanded over its 80-plus-year history from an underground room and pillar operation to a modem surface snip mine. Currently, the mine feeds four on-site power plants using conveyors, has a filly automated truck load-out, and ships coal by rail to nearby Wyoming power plants. Annual production of 4.8 MTFT is accomplished on a single-shift basis with 53 fill-time production, maintenance and administrative personnel. In 1990 a decision was made to modernize the coal feed system to the power plant complex with modular conveying equipment. The project involved constructing coal storage silos, overland conveyors, feeder breakers and modular conveyors to follow the mining benches. Total project cost in excess of $25 million was used to construe or commission: A 2,150-TPH 48-inch overland conveyor with horizontal curve A 2,150-TPH 48-inch plant feed conveyor 13 shuttle conveyors, each 150 feet in length 2 front-end loaders equipped with large coal buckets 2 crawler-mounted feeder breakers with compatible discharge conveyor 1 high-lift shuttle conveyor with adjustable discharge height 1 high-angle conveyor 2 4,500-ton coal silos with automated truck load- out capabilities. Conceptually, the plan was to develop 33 MTONS of reserve adjacent to the plant complex and use front-end loaders to tram ROM coal to in-pit feeder breakers. The primary crushing would reduce coal to 6-inch minus and feed through a series of shuttle conveyors to an overland supply conveyor. The overland conveyor would feed the secondary crusher, and the crushed product would be moved to any of four storage silos using conveyors. The in-pit crushing and conveying system is a unique fit for the power plants and provided many interesting challenges for the coal mine to overcome. System integration, maintenance windows, equipment availability and the like had a major role in engineering the system to a power plant complex having no emergency coal stock- pile and limited plant storage. In crediting the designers and operators, the in-pit conveying system at the Wyodak Mine has delivered coal to the power generators since 1994 with little or no downtime. ENGINEERING CONSIDERATIONS Yearly production for the mine is based on 3.5 MTPY which requires about 1,550 TPH on an 8 hour, one-shift- per-day, 5-days-per-week basis. Considering efficiencies for starting and stopping, crew transport, loader trams, and operational delays, a nominal conveyor feed rate of 2,150 TPH or 72% system utilization was used in engineering design application. This ton-per-hour basis is used to size and commission the remaining components of the in-pit system. Coal quality requirements also played a role in equipment selection. The mine reserve grades vertically and coal from Upper and Lower benches needed to be mixed in any given proportion. This required equipment to be filly variable and capable of producing all or part of the 2,150-ton-per-hour requirement. Bisecting the 80-foot- high coal face for quality required construction of a high lift module capable of reaching a single overland conveyor 40 to 50 feet above the pit floor. Designers built a high-lift, adjustable and portable module specific for this application Having two bench systems capable of each producing the required feed for the power plants required computerized control processes to control on-line production. RSLinx, RSLogix, and RSView were chosen as the communication and control software, and a Data Highway Plus serves as the communication backbone. Each of the two in-pit benches are controlled with a data center equipped with Allen Bradley 5-40 processors. This

Jan 1, 2004

By P. Schmäh

Nowadays, small diameter tunnels are increasingly considered in pipeline projects as an alternative for sensitive crossings or when soil conditions limit the use of conventional pipeline installation methods like HDD. Safety concerns play a key role, especially for inner-city installations. Pipe jacked microtunnels and small segment lining tunnels can serve as casing tunnels if access is required during construction for the change of cutting tools in challenging ground conditions or for maintenance of the pipeline in operation. Small diameter tunneling solutions offer a high degree of flexibility for alignment design in terms of geology, length and radius.

Jun 13, 2021

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By Wayne D. Gould

Planning for a project does not start with the announcement of the approval for a project. Planning actually begins when the project is only a prospect and it involves the years of experience of many people because their expertise influences the final decisions. In partial anticipation of the Pinto Valley project, as well as a search for improvement in the Copper Cities operation, two projects were undertaken. The first project was to substitute one 26" cyclone for three 20? cyclones in the single stage grinding circuit. The second project was to replace the Hunt air flotation cells with 300 cubic foot mechanical cells. The 300 cubic foot cells were just being introduced, consequently two types of cells were selected for testing. The results from both projects influenced the decisions on equipment for the Pinto Valley project.

Jan 1, 1975

By D. L. Langhans

Platinum-group metal (PGM) converter matte from the Stillwater Complex, MT, was subjected to chemical and biological leaching in an effort to upgrade the matte by decreasing the Cu and Ni content. Copper and NL extractions were optimized in a two-stage chemical leach. Atmospheric pressure sulfuric acid leaching removed over 90 pct of the Ni and Fe in the first stage, while 95 to 98 pct of the Cu was removed is the second stage using an acidified cupric chloride leach. This two-stage leach, followed by an elemental sulfur removal step, decreased the weight of the matte by 90 pct. The combined Cu and Ni content was reduced from 65 pct to less than 20 pct, while the PGM content was increased from less than 2 pct to 26 pct. Biological oxidation using Thiobacillus ferrooxidans also proved to be an effective method for removing Cu and Ni. Over 90 pct of the sulfide was oxidized and 99 pct of the Cu and Ni were solubilized, leading to a 60 pct reduction of sample mass during the 17 week bio-oxidation of the Stillwater converter matte. The final residue, after removal of jarosite that accumulated during bio-oxidation, contained less than 3 pct combined Cu and Ni and 6 pct MM.

Jan 1, 1993

The 26th international APCOM symposium, hosted by The Pennsylvania State University, was held Sept. 16 to 20, 1996 in University Park, PA. Conducted about every 18 months throughout the world, APCOM symposia focus on the Application of Computers and Operations Research in the Mineral Industry. The APCOM International Council is the governing body of the symposia and determines the symposium’s locations and sponsorships. This group is composed of the nine permanent (voting) members. They include the University of Arizona, Colorado School of Mines, Pennsylvania State University, Society for Mining, Metallurgy and Exploration, Inc., Canadian Institute of Mining, Metallurgy and Petroleum, South African Institute of Mining and Metallurgy, Technical University of Berlin, Institution of Mining and Metallurgy and Australasian Institute of Mining and Metallurgy. The three nonvoting members are Moscow Mining Institute, China Institute of Mining and Rudarski Mining Institute of Slovenia.

Jan 1, 1996

By Irwan Halim, Stephane Polycarpe, Brian Hann

The Narragansett Bay Commission Phase III CSO Program includes construction of the 11,600-foot long, 30-foot ID, deep rock Pawtucket Tunnel in Rhode Island. This paper provides an overview of the Design Build Project features and highlight some of the important design considerations, features, and innovations, including geologic conditions and related TBM design, and deep shaft and tunnel segment designs. The paper provides the most recent updates on some of the project construction activities including TBM tunnel progress and retrieval schemes, tunnel pump station and deep vertical shaft liner installations, SEM construction, and microtunneling for the longest adit using Fiberglass Reinforced Polymer Mortar pipes.

Jun 23, 2024

By Roland Arnold, Richard Gradnik, Martin Zeindl

This paper presents the details of the Kramer tunnel project in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of GarmischPartenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million (incl. VAT), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for single-tube tunnels is solved by a parallel escape tunnel passable for vehicles. All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). In order to reduce the geological risk for the owner, the escape tunnel was supposed to be completed before the design process for the main tunnel ever began. The exploratory tunnel was awarded to a competitor with an separate contract.

Jun 13, 2021

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications. KEYWORDS: Gearless Mill Drives, Gearless Conveyor Drives, Availability, SAG Mill, Ball Mill, Overland Conveyor, Antapaccay INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump…) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch…), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment) Intermediate gearboxes are not required when a motor is used with a rated speed that directly matches the speed requirement of the driven equipment. Furthermore the VSD can be used to smoothly start the motor and to vary speed during operation, which means that it satisfies both requirements."

Jan 1, 2015

By E. Molleman

This paper reports on testwork exploring the dissolution/reprecipitation reaction: ZnS + 2HCl ? ZnCl2 + H2S, as part of a process for the production of pure ZnS. In spheroidal form, this would constitute a premium fonn of zinc refinery roaster feed enabling the production of pure ZnO. The research focused on the influence of proton activity on dissolution of zinc concentrates from Brunswick Mining & Smelting, Red Dog and Tara. The results and thermodynamic data suggest that the three concentrates contained significant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1997

By M. E. Kuchta

Surface coal mine design can be facilitated with the use of an interactive graphics personal computer program. This mineral inventory and planning program (POLY CALC) is described and its use is illustrated with a case study. The case study deals with investigating a stripping sequence and associated dragline stripping requirements.

Jan 1, 1986

By Klaus Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300 and 600 °C is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies depending upon structural homogeneity, porosity and gangue quantity. Especially sinters with heterogeneous structures transmit stress to the hematite phase and this favours disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 1, 1981

By Vishnu S. Gupta

A modular computer program APEX (AMAX Process Evaluation Executive), has been developed at AMAX Extractive R&D, Golden, Colorado to facilitate rapid simulation of steady state material and energy balances of existing and/or proposed metallurgical process flowsheets. Currently, APEX is being used for the design, analysis, and evaluation of several of AMAX?s Nickel, Molybdenumand Tungsten processes. A unique feature of APEX is that it allows specifications of flow rates and compositions for different solid size fractions in addition to aqueous organic and gaseous phases. Thus, a metallurgical process which may involve crushing, grinding, flotation, leaching, washing, solvent extraction, precitation and refining operations can be simulated in a single computer run using APEX. APEX requires two input data files. The first is a process data file which includes physical and thermodynamic properties of the various chemical components of interest. This data file is unique to the process under study and does not require changes for alterations in the process flowsheet. The second data file is specific to a simulation case and includes descriptions of the flowsheet, various feed streams and the process equipment's operating conditions. In addition to temperature, pressure and percent solids, calculated information for each stream includes weight and volumetric flow rates, chemical compositions, specific gravities and enthalpies of solid, liquid and gas phases. For each process equipment in the flowsheet, APEX prints its operating conditions and detailed information about the streams that enter and leave the unit. Models of several general unit operations are preprogrammed in APEX. Also, the modular design of APEX permits quick and easy additions of simulation models which are specific to new and/or unique process operations. To study process stability and optimization, APEX permits several cases of a flow-sheet to be run together. Three simulations of the Moa Bay Nickel process have been excluded to illustrate the ease and flexibility of using the APEX system.

Jan 1, 1980

By Don C. White

Santa Rosa is a mid-Tertiary, volcanic-hosted, bulk-mineable, open-pitable, heap-leachable, gold-silver deposit. It is the product of hydrothermal mineralization along an arcuate segment of a caldera collapse ring fault in a probable maar volcanic setting. This segment was later broken by radial faults. Gold occurs principally as electrum finely disseminated through intermediate tuffs, and associated with pyrite, at Santa Rosa. The nearby Alto de la Mina deposit displays stockwork silica-pyrite-gold in a tectonically and hydrothermally shattered andesite flow. Miocene epithermal mineralization was accompanied by central silicification and pyritization and more distal argillization. An andesite flow cap rock at Santa Rosa played a pivotal role as an upward permeability barrier. Highest gold grades and most intense alteration occur closest to the ring faults and immediately beneath the andesite flow. Supergene alteration effects on the gold distribution are minimal.

Jan 1, 1993

By A. Lashgari, V. Kecojevic

This paper presents research on the environmental impact of digging and loading equipment used in surface coal mining. Environmental impact was assessed through the measurement of equipment exhaust and dust emissions, and sound level. In this study, exhaust emission refers to carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur oxides (SOx) and volatile organic compounds (VOCs). Dust generation refers to fine particles (PM2.5), inhalable particles (PM10) and total suspended particulate matter (TSP). Sound level refers to the sound pressure level at different distances from the equipment. Modeling of the environmental impact of digging and loading equipment was conducted using the Microsoft Visual Studio.NET software package. This research was a part of a broader project involving the development of a software system for the selection of productive, cost-efficient and ecofriendly mining systems, sponsored by the Appalachian Research Initiatives for Environmental Sciences (ARIES). This research may assist mining professionals in quantifying the environmental impact of digging and loading equipment, and developing strategies for reducing the overall impact of such equipment in surface mining.

Jan 1, 2013

By D. W. Alexander

Researchers from the U.S. Office of Mine Safety and Health Research (OMSHR) of the U.S. National Institute for Occupational Safety and Health (NIOSH) completed field trials during coal mine rescue contests using simulated gas detectors in place of placards. The gas monitor simulator (GMS) devices replaced static, paper placards to deliver gas concentration data. Eleven teams were observed during the field contest, which was approved by the Mine Safety and Health Administration (MSHA). GMS devices were given to three team members (the captain and both gasmen). Observation of teams revealed that team members changed behavior by acknowledging and sharing information more often while using the GMS. As a result of this research, it has been demonstrated that under the existing contest format, the newly developed GMS device may be used with no adverse impact on team contest performance. Furthermore, when GMS technology advantages are used, contest realism is improved. In the future, competency assessment may be incorporated.

Jan 1, 2012

By Ilmar J. Martens

The statistical information and cost data used in this report has been made available by NICKDATA INC. Since 1982, NICKDATA INC. of Toronto, Canada, has produced an annual comprehensive nickel industry cost study. Up to date information on 22 mines, 21 smelters, and 16 nickel refineries representing 30 nickel production operations in 17 countries are included in the computerized cost analysis. The report is compiled from information obtained through regular annual visits to major nickel operations and continuous monitoring of information on all nickel producers. The 1984 report which was completed this summer, reveals drastic changes in the nickel industry cost structures.

Jan 1, 1984