Search Documents

By P. C. Schutte, N. B. Strydom, A. J. Kielblock

Three groups of unacclimatized men were subjected to five-day climatic-room procedures at wet-bulb temperatures of 29,30, and 31 C respectively. The findings indicated that individuals reach a satisfactory level of heat acclimatization for work in environmental temperature conforming to those at which they were acclimatized. It is, therefore, superfluous to acclimatize men at wet-bulb temperatures that exceed those at which they are destined to work. These methods of acclimatization can be linked advantageously to heat-tolerance testing at mines with suitable underground temperatures.

Jan 1, 1983

By A. A. Hazell

Mine management by objectives By A. A. HAZELL The author discusses the objective areas of mine management. Setting objectives is seen to be a conscious process which starts at the highest level of management. This enables clear objectives to be set at each lower management level. The methods of setting objectives in the areas of stope production, productivity and manager performance are set out in detail. In the area of manager performance emphasis must be placed on the practice of management. It is concluded from results obtained that "management by objectives" produces better than average perormances.

By A. D. Thomas, K. C. Wilson

Some years ago, the authors developed an analysis of non-Newtonian pipe flow based on enhanced turbulent microscale and associated sub-layer thickening. This analysis, which can be used for various rheologic modelling equations, has in the past been applied to smooth-walled pipes. The present paper extends the analysis to rough walls, using the popular Bingham plastic equation as a representative rheological behaviour in order to prepare friction-factor plots for comparison with measured results. The conditions for laminar-turbulent transition for both smooth and rough walls are also considered, and comparisons are made with earlier correlations and with experimental data.

Jan 1, 2007

By A. Smith

After the introduction of mechanized bord-and-pillar development at Dumacol in 1958, pillars were being developed at a much faster rate than they could be extracted by hand loading methods. Efforts were therefore made to increase the rate of pillar extraction by mechanization. Following two partially successful mechanized stooping trials in 1964 and 1971, it was decided that mechanized pillar extraction with 1 m3 cable-reel front-end loaders should be introduced. The first section to employ the new equipment started production in May 1979, and the mine now has four mechanized pillarextraction sections in operation. Considerable improvements in production, productivity, safety, and percentage extraction have been achieved.

Jan 1, 1985

By J. A. L. Napier

The application of excess shear stress as an aid to the design of mine layout is reviewed, and the critical parameters required to describe slip on a plane of weakness are noted. A design procedure that is required to model the cyclic build-up of excess shear stress is described. A number of simple examples of mine layouts on two reef planes intersecting a fault plane are then considered to illustrate the application of the design concept and to highlight some of the pitfals that may be encountered

Jan 1, 1987

By G. J. Kringe

The results of a series of measurements of accelerations and guide-roller loads made on mineshaft conveyances are given, together with the predictions of these accelerations and loads based on a computer programme. The analysis of the measurements is described, and the results of the measurements and computer predictions when compared show reasonable agreement. Some parameters that increase the guide-roller loads are identified, and their effects are studied, together with some comments on the total loads. Finally, a possible format for a design specification is discussed, and some tentative design values are given.

Jan 1, 1986

By C. O. Beale

This paper is the first part of a two-part review on the subject. , , .. Here reference is made to the place of copper among the elements, Its properties, Its historical significance, and its 'end uses both in general and in South Africa. Its current market situation and its prospects are dealt with briefly. Some account is then given of the mining and metallurgical techniques employed. in South Africa in the production of copper, together with the names of the companies at present Involved and brief descriptions of their operations, ,... . .. The operations of these companies are described In greater detail In Part 11(Apn11985 Issue of the Journal).

Jan 1, 1985

By O. G. Pauw

The relationships between mill power and pebble load, bulk density of the load, and circulating load were investigated on the pebble mills in the grinding circuit at Buffelsfontein Gold Mine. This paper describes the most significant relationships among the operating and control variables on the plant, and illustrates these by reference to experimental data gathered from the plant during operation. The results were used for the development of very successful multivariable peak-seeking controllers for the pebble load and bulk density of the load on these pebble mills. The peak-seeking control algorithms are described in detail. The control system has operated successfully at Buffelsfontein for more than 18 months and is still in operation.

Jan 1, 1985

By M. J. Nicol, G. Cromberge, C. A. Flemming

A relatively simple rate equation for the kinetics of the absorption of gold from cyanide solutions onto activated carbon was lI5ed as the basis in the development of a model for multistage carbon-in-pulp and carbon-in-Ieach absorption circuits. The model was used in the prediction of both the steady-state and the transient behaviour of the absorption process, and the results were found to be in reasonable agreement with those observed in an extended pilot-plant campaign. A number of practical implications of the model are discussed, and an assessment is made of the economic consequences of the various process options available for the design of a carbon-in-pulp plant.

Jan 1, 1983

The Institute has concluded an agreement with the Chamber of Mines whereby the Chamber Librarian maintains a section in the Library for the Institute. Surface effects of underground mining South Africa is blessed with vast mineral resources. It is essential to exploit those reserves if the country is to remain economically viable. Surface-mining equipment The Goldfields Mining Expo '86 is to be held in Kalgoorlie, Western Australia, from 30th October to 1st November, 1986, in conjunction with the Annual Conference of the Western Australian School of Mines. Mintek reports Report M142D Characteristics of gold and pyrite flotation at the Chemwes plant. (1st issued May 1984.) Report M159D Beneficiation tests on andalusite ore from the Marico district. (1st issued Aug. 1984.) Report M164D The recovery of tungsten from South African low-grade schee/ite concentrates. (1st issued Sep. 1984.)

Jan 1, 1986

By V. M. Lovell, N. P. Finkelstein

The concepts involved in flotation research are discussed and aims are presented. Three different method. of investigation can be used, all of which are applied at the National Institute for Metallurgy (N.I.M.), and these are the empirical, trial and error method, the chemical engineering method, and the physicochemical approachs This paper is devoted to the last of these. Because of the complexity of the physicochemical interactions involved, the work has, to a large extent, been concentrated on only one aspect, viz. the interaction between the mineral surface and reagents in solution, which was considered of major importance in the understanding of the process. The aspects on which work has been done are the concentration of uranium, the reaction between salt minerals and fatty acids, mixed xanthate-cationic collector systems, and the reaction between sulphide minerals and thiol reagents. Selected problems from the first two of these are discussed in some detail and deal with the agglomeration flotation of uranium and the chemical control of the flotation process for phoscorite. A detailed discussion is also presented of the progress made in the understanding of the interaction between sulphide minerals and thiol reagents, which is of more general application. Finally, an indication is given of the future direction of physicochemical research at the N.I.M.

The AK6 kimberlite is situated 25 km south of the Debswana Orapa Mine in Botswana and was discovered by De Beers geologists in 1969 during the follow-up of geophysical targets in the Orapa area. The kimberlite was not extensively pursued at the time as the initial bulk sampling indicated it to be of limited size and low grade, factors largely contributed to by the basalt breccia capping. Completion of high resolution integrated geophysical techniques and drill bulk sampling to depth recovered 97 tons of kimberlite during 2003 and 2004, which led to the increased size and grade estimates. Bulk sampling by Large Diameter Drilling (LDD, 23 inch diameter) commenced in 2005; 13 holes were drilled to a cumulative depth of 3,699 m and 689 carats of diamonds were recovered. In July 2006 the De Beers Mineral Resource Classification Committee classified these Phase I LOO results at a High Inferred level with an average grade of 24 carats per hundred tonnes (cpht) at a bottom cut-off of +1 mm, and a modeled average diamond value of 150 dollars per carat. A second phase of LDO drilling was initiated in 2006, and bulk sampling by trenching commenced in 2007 in order to deliver a resource estimate at indicated level. An Indicated Resource of 11.1 million carats at an average grade of 22 cpht was declared for the deposit mining lease application lodged in 2007.

Jan 1, 2010

By R. J. Davidson, V. Veronsee

Some of the parameters affecting the elution of gold from freshly loaded activated carbon using pure water as an eluant were studied. The procedure involved pretreatment of the gold-loaded activated carbon with a strong reagent of sodium cyanide and sodium hydroxide, followed by elution of the gold with water. Gold-loaded carbon obtained from three different sources was studied. It was shown that the elution temperature was the most critical parameter, and column operation at I !OCC (gauge pressure of 50 to 100 kPa) is suggested. The effects of variations in the concentration of sodium cyanide required for the pretreatment of loaded carbon and of variations in elution flowrate were also investigated. Both these parameters were found to have only a marginal effect on the efficiency of gold elution. The investigation also indicated that gold-elution rates were affected to a considerable degree by the particle size of the carbon concerned. Higher elution flowrates could be used when carbons of finer particle size were eluted. A modified eluate-collection procedure was also developed during the course of the investigation. Oven-drying of the loaded carbon was shown to have little or no effect on the efficiency of the subsequent gold elution. The calcium and silica contents of the various carbon samples were also determined. It was immediately evident that the calcium content was very considerable in the case of loaded carbons originating from carbon-in-pulp operations. Calcium concentration was particularly high where air agitation had been employed in the carbon-contacting circuit. To some degree, the calcium build-up explains the serious carbon fouling taking place, resulting in a decreased efficiency of gold adsorption. The fouling problem was found to be less severe when mechanical agitation was used. No poisoning by calcium carbonate was observed where the pregnant solution had been acidified before it was contacted with the carbon.

Jan 1, 1979

By E. Rex, T. J. Goff, W. S. B. van Beek, P. E. Nel

"The PGM smelting industry is known for operating at significant high superheats. Both the slag and matte phases that separate via gravity need to be tapped out of the furnace in a safe and efficient manner, which can be achieved only through sound tap-hole management practices. This paper gives an overview of the tap-hole management approach followed in the operations at Lonmin’s Western Platinum Smelter.Five circular AC furnaces are operated, with each furnace comprising essentially a crucible and auxiliary equipment. Within the crucible, slag and matte tap-holes are situated at different elevations. The slag phase is tapped at a higher elevation than the matte phase. At the three older furnaces, tapping is done by the conventional method of lancing open the tap-hole and closing it with a dolly. However, at the two newer furnaces, tap-holes are opened and closed with the aid of a drill and mudgun.Tap-hole management can be divided in a number of aspects. In order to achieve a safe opening and closure every time, Lonmin distinguishes between three important aspects - the design of the tap-hole system, the operating practices followed, as well as care and maintenance. This paper briefly describes the tapping channel and cooling requirements for handling superheated matte, together with the difference in design of the matte and slag tap-holes. Mention is also made of the importance of auxiliary equipment, which includes the launders, fume extraction, granulation water, and mudgun and drill units. Improvements made to the matte tapblock design are discussed.The monitoring, alarm, and safety systems related to matte and slag tapping are described. Tap-hole life and different wear mechanisms are mentioned. Tapping can be done safely only if the tap-holes and equipment are maintained properly. Mention is made of the tap-hole refractory repair practices, and the improvements made in order to reduce repair time as well as to extend the time between deep repairs. The importance of the correct tap-hole clay selection in order to nurse the tapping channel after each tap is also discussed.The paper finally touches on some research and development work that was done in order to improve the monitoring of the condition of the tapblock by means of fibre optic temperature sensors"

Jan 1, 2014

The President: We are very fortunate tonight to have with us Professor Franz Pawlek, Head of the Institute of Extractive Metallurgy for Non-Ferrous Metals of the Technical University, Berlin. In him we have a representative from one of the few mining and metallurgical universities in Western Germany, since I understand there are only three such universities, Berlin, Aachen and Kassel. The latter is represented by Mr Schmelling who has accompanied Professor Pawlek here tonight. The famous Freiberg University is on the other side of the Iron Curtain, and so is Breslau. Professor Pawlek was born in Vienna many, many years ago, and he obtained his diploma and then later his Doctor's Degree in metallurgy, in Vienna. For four years he worked for an Austrian company, and then moved to Berlin and joined the A.E.G. Company. After the war, he joined the Institute, which had been very heavily damaged, and he was closely associated with the rebuilding and re-equipping of the faculty of mining and metallurgy. He has written numerous papers, and I am sure we are going to have a most entertaining and interesting evening's talk. The President: Gentlemen, I am sure you would like me to thank Professor Pawlek for his talk tonight. My knowledge of pressure leaching is particularly small, limited to a friendship with Professor Frank Forward, to whose original work at Fort Saskatchewan reference has been made by Professor Pawlek. I enjoyed Professor Pawlek's talk, and as a mining engineer I managed to follow most of the argument, mainly because it was so lucidly presented, aided by these informative slides; but I never realised how complicated a problem this process can be. I am taking the liberty of asking Professor Howat to express our thanks from a more technical point of view. After Professor Howat has spoken, and possibly posed a few questions, I shall throw the meeting open in the hope that various people here will be prepared to ask questions. I see one or two gentlemen who have been over in Canada studying pressure leaching lately, and I hope they will ask questions, informally if they so wish. We will not record the full proceedings of this meeting tonight, in the hope that there will be more questions of a general nature. Thank you. Professor Howat: Mr President, Professor Pawlek, I am afraid I am up here under false pretences, because the matter that I thought I was asked to do was to propose a word of thanks, and I usually thought that a word of thanks was taken at the end,-however. It is always very intriguing to think that for all these thousands of years that have passed, pyrometallurgical processes have provided the main methods of extracting metals from their ores. Within the last 100 years, hydro metallurgical processes have become of increasing importance, and it is quite interesting to speculate that the largest single hydrometallurgical process is the one that we operate in this country,-which was devised by two distinguished countrymen of mine,-namely, McArthur and Forrest.

By N. A. Barcza

This paper describes the development of large-scale thermal-plasma systems, which was motivated, in general, by the potential cost savings that could be achieved by their use as a replacement for the more conventional methods used in the generation of thermal energy. The anticipated cost savings arise not only from the use of plasma-generating devices but from the manner in which they have been interfaced with a furnace to process particular materials, mostly as fines. Thermal-plasma systems fall into two categories: non-transferred-arc and transferred-arc devices. In general, transferred-arc devices have been interfaced with open-bath furnaces in which melting or smelting processes carried out, while non-transferred-arc devices have normally been applied to shaft furnaces. Water-cooled transferred-arc devices are somewhat limited in power (about 5 MW) because of the relatively voltages (300 to 500 V) that can be attained in open-bath furnaces, where very long arcs are undesirable, and because only relatively low levels of current can be carried. Graphite electrodes can overcome the restriction current, and power levels of 30 to 50 MW seem feasible, even with one electrode, if direct current is used. Multiple water-cooled devices are capable of attaining similar power levels, but the capital costs are much higher. Costs due to electrode wear are lower for water-cooled systems, but expensive gases are needed for transferred-arc devices. Mintek conducted extensive pilot-plant work in which water-cooled devices were used initially but graphite electrodes were used subsequently to produce ferochromium from fines. Transferred-arc open-bath configurations were used. This work led to a decision by Middelburg Steel & Alloys (MS&A) to install a 16 MVA furnace of semindustrial scale to produce ferochromium aloys based on the ASEA d.c. arc furnace developed for the Elred process. Non-transferred-arc devices have atained reasonable scale-up to the 6 to8 MW power level, and high-voltage operation, which is inherent in such devices, has enabled lower currents to be used. Nevertheless, multiple systems are still necessary to accommodate large-scale applications, and this can be costly from a capital point of view. The cooling requirements are large, and can represent a considerable loss of electric energy. Shaft furnaces equipped with non-transferred-arc devices are suitable for the processing of materials that have volatile species, e.g. silica or manganese, or where the shaft is used to prereduce oxides that are amenable to gas-solid reactions. It is probably in the treatment of light and refractory metals that plasma technology will achieve its greatest development in the years to come. The energy requirements for the production of these metals are high, and very low oxygen potentials are necessary. These are factors that favour thermal plasma. Much developmental work is still needed in this interesting field. It should be remembered that electrically generated thermal energy is a unique temperature source that, in many instances, cannot be replaced technically or economically by the combustion of a fuel.

Jan 1, 1986

For the past 12 years, the Universities of Stellenbosch and Cape Town have hosted an annual symposium to discuss research topics in Minerals Processing. Since 1987, this meeting has been held under the auspices of the Western Cape Branch of the South African Institute of Mining and Metallurgy, and has enjoyed much national and international support. In 1993, in place of the usual Symposium, the Branch and Universities collaborated with CSM Associates Ltd and Minerals Engineering Journal is organizing the international Minerals Engineering '93 Conference in Cape Town.

Jan 1, 1993

By K. L. Morton

This technical note reviews the status quo of mud rushes and flooding, which have claimed them lives of many people in underground mines in South Africa and globally. Given that the causes are well known and can be managed, the note calls for the development of a national and global standard on flood and mud rush prevention in order to save lives.

Mar 30, 2026

By H. H. McGregor

SYNOPSIS Changes in the national productivity (gross national product per head of the population) have been assessed in order to derive a target figure for the required annual increase. The conclusion reached IS compared with the targets of the economic development programme of the Republic. Productivity and management structure in the gold mining industry is then analyzed together with investment in plant, machinery and equipment for rock handling purposes. The conclusion is drawn that productivity improvement does not appear to have accorded with the massive expenditures in plant and equipment, and in augmented management. The productivity of the manufacturing and construction sectors of the economy has been examined. The principal difficulty is that the main avenue of approach is the value of product divided by the total labour force. This introduces inflationary questions, and the use of a suitable deflator becomes of prime importance. Severa1 different methods of assessing the productivity improvement in the industrial sector have been used with what is regarded as a comparatively high degree of compatibility. Improvements in productivity in the manufacturing industry up to 1966 appear, from the information available, to have substantially exceeded comparable figures for the mining industry. There is however evidence that thereafter productivity of the manufacturing industry has not maintained this satisfactory rate of increase. If the economy is to achieve the planned rate of expansion, there is no doubt that greater attention to this aspect will be required in the future than has been accorded to it in the past.

By R. Perlman

This paper describes the various new computer-aided techniques being used by economists in the construction of economic models. It discusses the relevance of these techniques to mining industries. In particular, it describes their role in making it possible to obtain better estimates of future price and demand developments on the markets on which metals are sold, and how these estimates can be used to improve forward planning by mining companies.

Jan 1, 2014