Search Documents

By Donald Jonson

Stockholm’s Northern Link, currently Europe’s largest urban road tunnel project, will be about 5 km long from west to east. Running through two separate, mostly parallel tunnels, each with 2-4 lanes, the complex will include numerous entries and exits, as well as a major branch to the north. The total length of tunnel will be 11 km, of which 9 km will be in rock. Over million m3 of rock will be blasted. The Northern Link will open to traffic in 2015. After a 10-year stop to deal with environmental questions regarding Ekoparken, Stockholm’s unique “national city park”, the Northern Link project in the Swedish capital was restarted in the autumn of 2006, with the construction of five works-access tunnels.

Jan 1, 2009

By Robert Hopler

INTRODUCTION NOT so very many years ago the farm was about the last place where one would expect to find up-to-date mechanical appliances. Steam, explosives, electricity—the factors which have made the world in general, and America in particular, what it is today— were indispensable for the railroad and the steamboat, the factory and the mine, but the farmer’s work was generally run on a comparatively small scale, and was mostly done by the muscles of men or draft animals. Today, however, the farmer as well as the manufacturer, the contractor and the miner, fully appreciate the value of labor-saving devices. Every up-to date farm, large or small, has modem machinery that tends to reduce the cost of production or to improve farm products.

Jan 1, 2011

By Leslie C. Taylor, Scott A. Yamada, William L. Fourney

Previous studies have shown that the pressure load on a target by a buried explosive charge is not smoothly distributed. The effort reported here was undertaken to explore the mechanisms believed to cause this uneven pressure distribution: jets from the surface originating in instabilities caused by the explosive shockwave interacting with surface irregularities. Small-scale tests using conical, hemispherical, and cylindrical indentations in the sand surface above a buried charge were conducted to identify trends in the velocity and form of the resulting jets. In these tests, the most important factor affecting the resulting jets was the distance between the bottom of the indentation and the top of the charge. Cylindrical indentations resulted in higher jet velocities than those from comparable hemispherical and conical indentations.

Jan 1, 2012

By Robert B. Hopler

The history of bulk loaded explosives begins with the loading of black powder and RRP (Railroad Powder) into vertical boreholes. The early air place, net of black powder and nitrostarch dynamites is covered, as are the brands and formulas of the nitroglycerinsensitized "Bagged" powders.

Jan 1, 1993

By Jennifer Paukula, Steven Lindsay, S. Joon Kim

String loading is the placement of a bead or ‘string’ of emulsion along the lower edge of a development drill hole. The loading hose extraction rate controls the amount of emulsion placed in each drill hole. This allows a controlled distribution of explosive energy throughout the development round. Center holes are loaded using the slowest extraction rate causing the majority of the explosive energy to be placed in the center of the round. The loading hose is extracted successively faster for the buffer and perimeter holes causing less explosive energy to be placed near the edge of the blast. This causes less damage to the rock mass that remains in place after the development blast.

Jan 1, 2012

By Italo Onederra, Jason Furtney, Ewan Sellers

The Hybrid Stress Blasting Model (HSBM) is a high level blast modelling research tool which provides results that can still be used implicitly for practical blast design. The code is being developed through an international collaborative research project funded by a consortium of companies which is comprised of explosive, equipment suppliers and major mining houses. A key component of the HSBM is the numerical code and user interface designated as Blo-Up 2.5. To date validation work has focussed on breakage, fragmentation and damage outcomes in controlled laboratory experiments and using large concrete cubes

Jan 1, 2012

By Jeff Gore, Jack Dermody, David Gribble, Brett Macaulay, Bart Sharpe, Paul Klaric, Paul Thornley, Ben DeVries

Optimal Fragmentation in Block Caving is difficult to achieve as it is generally defined by the rock mass itself and the way in which the cave is initiated. The lower portion of the cave has even less chance as the material has little time for self comminution. Blast Preconditioning of the Block Cave is designed to engineer the lower section of the rock mass to produce material of a suitable size to assist in the initial cave propagation and improve initial drawbell productivity. At Cadia East a plan was developed to drill 150-metre long, vertical up-holes from the undercut level and blast them fully confined to produce fractures in the rock mass. The blast itself was a simple undertaking. However, in the year preceding the first production blast, all aspects of the process were designed, tested and refined across multiple trials. As this type of challenging application had not previously been encountered in Australia there were many unique situations to address. Products and systems had to be developed and adapted to overcome these challenges. These included: Formulating and manufacturing an explosive that is robust and of a high VoD; designing and manufacturing easy to use electronic initiation systems; and, designing pumping systems to combat high head pressures to allow for successful and safe loading of the holes. Close collaboration with the customer ensured that the trials culminated in successfully blasting a hole containing almost 3.3t of explosive. These trials have since led to the blasting of four holes instantaneously, which contain almost 13t of explosive. This paper describes the various components of the system, the challenges and the final result.

Jan 1, 2013

By Per-Anders Persson

TIGERWIN, now on CD, is a user-friendly personal computer code (running under Windows) which determines the detonation and expansion state of an explosive from its known chemical composition. TIGERWIN is intended for users in the mining and commercial explosives industry who do not routinely program or run Fortran codes. The code allows the user to open a window on the computer screen and enter the initial density and the weight percentage composition of an explosive, ingredient by ingredient. Alternatively, the code can balance the composition with one or more ingredient percentages fixed, while proportionally adjusting the others automatically to give a total of 100%. The equation of state and its parameters can be user-selected from several proven and tested versions of the BKW, the JCZ, and the ideal gas equations of state. TIGERWIN allows the user to select several options for different additional calculations, such as determining the constant volume explosion, the Chapman-Jouguet (C-J) point, the detonation Hugoniot, the expansion isentrope from the C-J point, and point calculations with selectable specific volume and temperature. Additional options include calculations of detonation data with one or more ingredients partially reacted, assuming either temperature equilibrium between reaction products and unreacted material, or keeping the unreacted material “cold” at the initial temperature. Thus the code can run both ideal and non-ideal detonation calculations. The code automatically saves the input and output files in a separate directory for future reference. The output from several calculations can be displayed and printed in the form of a comparison table. In it, the key results of up to five calculations with different explosive compositions can be compared. The results from an individual calculation can be displayed graphically and printed with expansion work, pressure, or temperature as functions of specific volume. A complete listing of the details of the calculation results, similar to those from the original Fortran Tiger calculations, can also be displayed and printed. No computer experience is required to run the code and workshop participants are encouraged to bring in their own formulations to try out on TIGERWIN

Jan 1, 2000

By Mark A. Rugen

It may be difficult to imagine but small engineering companies do exist, even in relatively large cities like San Antonio. Due to the limited capital available for the purchase or use of equipment such as computers, many times the small company must evaluate a blast damage claim by limited means. This paper will discuss how a relatively small company has managed to become the leading blast damage experts in an area without the use of computers or sophisticated equipment. It will be shown that a single individual in a company who is familiar with vibration theory, local soil conditions and who does not mind spending long hours with a calculator and reference books can satisfy both the insuranc e adjuster or attorney, and the homeowner concerning the claim. Several examples will be given which show the typical flow of work and the ultimate outcome. This paper will focus on the special problems encountered by a small firm and how these can be overcome, and the unique interaction of a small engineering firm with both the insurance adjuster/attorney and the homowner that can lead to an equitable settlement of the claim.

Jan 1, 1983

By Ian Tolliday

Emulsion Explosives manufacturers are aware of the destabilizing effect that the presence of inorganic impurities such as magnesium and iron and organic impurities such as naphthalene sulfonates and alkyl amines can have on their emulsions. This destabilization often manifests itself as severe crystallization and subsequent product loss. This paper describes the performance testing of specifically developed emulsifiers which give greatly improved emulsion stability in the presence of high levels of impurities. The test work involved a series of stability tests using ammonium nitrate doped with various levels of crystal modifier and anti-caking agent. A further series of tests were done to evaluate the stability using ammonium nitrate doped with various levels of iron and magnesium ions.

Jan 1, 2018

By Finn Ouchterlony

"Recently detailed fragmentation data from blasts fired with electronic delay detonators (EDDs) in the Red Dog mine in Alaska were presented. They include a comparison with pyrotechnic detonators fordifferent in-­-row delays in a standard pattern and EDDs in an expanded pattern. Fragmentation was measured on the belt after the primary crusher. The Rosin-­-Rammler function (RR, two parameters) was used to describe the crusher product. This was combined with the JK SimMet crusher model and the CZM blast model (Crushed Zone Model, three to five parameters) to estimate a reasonable crusher feed (muck pile fragmentation or run of mine, ROM) for each fitted product. In this way the effect of delay timing and electronic detonators on the median fragment size x50 and uniformity coefficient n for both crusher product and the blasted rock was determined. "

Jan 1, 2012

By Richard Turnbull

Maules Creek mine is an open cut coal near Boggabri in the Gunnedah Basin of New South Wales, Australia. The mine is currently operating at an annualised run rate of 9.5Mt of saleable coal. The plan is to ramp up production to 13Mtpa. Maules Creek has multiple seams each with varying depths; the inter-burden ranges from a few metres thick to greater than 30m (98ft). Due to this, Maules Creek mine is utilising truck shovel operations rather than a cast/dozer push operation.

Jan 1, 2018

By Joshua Micah Hoffman, Lifeng Li, Jhon Silva-Castro

Since millisecond detonators were first introduced, at least two variables among others have been more closely considered when timing a mining blast; the accuracy and the precision of the initiation system. Unfortunately, those variables are often ignored when designing timing for mining blast. Despite the lack of consideration of the characteristics of the initiation system, in some situations, e.g., firing a blast hole with one deck and two detonators, changes in the blasting sequence can be the results of the overlapping between blasting charges. The consequences of such overlapping involve flyrock events, fragmentation and diggability problems, and other difficulties affecting the operation of the mine.

Jan 1, 2015

By Robert Jacob Cefalo, Rio Tinto Kennecott

At the end of 2016, the Mine started a new ore phase in the section of the pit located on the East Wall. The East Wall geological structures required controlled blasting for peak particle velocity (PPV) frequency vibrations to protect the wall. Frequency controlled blasting using linear seed wave superposition modeling was required and implemented to reduce the far-field affects to the wall. This paper covers the work done by the drill and blast engineering group, controls used to protect the mine infrastructure, and the continuation of work-to-date of frequency controlled blasting for wall stability. The narrow width of the layback required the combination of hole sizes to blast large diameter production patterns with smaller diameter trim patterns in the same blast. A single blast had to use different burden & spacing and hole diameters and required the use of different timings throughout the pattern. Electronic detonators were required to limit blast vibrations and accommodate the specific timings needed to reduce low frequencies. The geotechnical group with the help of geotechnical radars worked with the drill and blast group on creating a tracking and reporting of blast performance. The radar readings informed the drill and blast engineers of the performance of the blast as it related to the long term performance of the highwall

Jan 1, 2019

By Miquel Lamadrid, Changshow Sun, Chris Johnson

To reduce blasting overbreak and improve stope stability, several new blast designs were proposed for current and future stopes. Based on the analysis of the powder factor, and the extent of damage zone, the appropriate new blast design was selected. Excellent results were achieved from the new blast design. Comparing the new blast design with the old one, the largest of the overbreaks decreased more tan two times and average overbreak reduced more than two times. The new blast design is currently applied in all mining zones in Leeville underground mine.

Jan 1, 2008

By Francisco Sena Leite, Vinicius Miranda

Mine blasting is directly associated with ground vibration. If these affect critical structures (buildings pit walls, etc.) they must be mitigated to reduce the environment and social impacts. Vibration monitoring and control is one of the most important procedures in blasting because it will impact short and long term incidents associated with this blast effect. Technology moves ever forward, and today we have personal devices that are equipped with an array of sensors, for that reason the authors decided to investigate the possibility of using a personal device to do vibration control. This case study compares the same blast measured with a traditional seismograph and a smartphone. To validate this new methodology, attenuation laws were built with data from a traditional seismograph and a smartphone application. Predictions were also made prior to a set of blasts. Residual analysis was used for data validation from the two different sources. From the performed analysis, to prove the validity of this new methodology, the normality tests for statistics residues analysis proves that it is possible to infer that the model has a null residual mean and a small residual error. The achieved results show the accuracy of these devices, the authors pretend to show the potential of this equipment and open a completely new door for vibration analysis.

Jan 1, 2018

By Michael Wieland

The thermodynamics work-principle was used to develop the rupture-fracture-throw (RFT) model for ranking the performance of reduced-density explosives when shot in rock or other stratum. The RFT model revises techniques used for the rock-water-jelly (RWJ) model, where the reaction-zone remains trapped within the rock/stratum. Therein, ranking of performance refers to trends for the two resolved components of the total expansion work: the reversible mechanical work taken as the heave and the residual irreversible portion, taken as the undissipated shock. For numeric tractability, the RFT and RWJ thermodynamic efficiency were taken equal, while the RWJ late-stage confinement was replaced with restrained venting through the rock, to render the RFT inefficient heave. The transfer of heat from the reaction-zone was neglected and the root-power formula was used to render the gas-covolume. Ranking trends were found for a generic charge formulation over a wide ranging density, with underwater results noted for comparison. Realistic compositions, some with natural resource materials, were treated for just typical and reduced density. Rock characteristics, ranging from hard rock to weak stratum, were represented by their density and rupture compression strength. Quantitative test results for shock or heave in rock remain difficult, so qualitative guidelines remain helpful when reviewing the graphic trends. Theoretical refinements for rock fragment size-distribution remain under development, though some relationships are touched upon to gain insight.

Jan 1, 2011

By P. E. Hoffman, Joshua Ph. D.

The Institute of Makers of Explosives (IME) led a post-detonation debris collection project in conjunction with a large AN railcar detonation conducted by the Department of Homeland SecurityTransportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in the IMESAFR (Institute of Makers of Explosives Safety Analysis for Risk) Quantitative Risk Assessment (QRA) tool. The test also provided valuable data about AN detonation characteristics when it is driven to detonation. The test took place at the Utah Dugway Proving Grounds (DPG) on April 27, 2018 and the debris collection was conducted the following two weeks with an average of 20 persons per day and an approximate total of 1,400 manhours. This paper details the collection efforts, challenges, and lessons learned. It also presents some of the initial findings relating to the debris distribution.

Jan 1, 2019

By Alan Bauer

During the past several years, the trend to large-diameter blastholes in both open pits and underground mines along with the continuing developments in slurried explosives and delay systems has kept things exciting for the drilling and blasting engineer. This has been particularly so in underground mining, where new mining systems having lower cost and higher productivity have emerged. Crater technology has produced new large-scale methods for resisting front penetration in tar sand mining and also new underground retreat mining methods and methods of raising.

Jan 1, 1978

By Joel Warneke, Cristian Caceres, Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2008