Search Documents

By Alban Lynch, Benigno Aquino, Hakan Dündar, Alexander Kalugin, Marco Delgado, Alberto Palomino, Ali Türkistanli

Dynamic separators are efficient dry classifiers because new designs during the last 50 years have reduced the by-pass and improved the partition curve. By contrast cyclones have been used as classifiers in wet grinding circuits for 50 years but without serious change and the early problems which were caused by high and variable by-pass, and different mineral specific gravities, still exist. High frequency screens are now used for wet separation and the operating characteristics of closed grinding circuits using cyclones or screens are discussed. Data come from circuits at the Condestable, Cerro Lindo, El Brocal and Catalina Huanca mines in Peru, the Eczacibasi mine in Turkey, and the Apatit mine in central Kola Peninsula in Russia. All classifier data are described by their partition curves and all mill data by their breakage rates. With cyclones the by-pass, d50, and sharpness of the partition curve change as operating conditions change but with high frequency screens the values vary little because the by-pass is low, the sharpness is high, and d50 depends on the aperture size. Data from all plants indicate that lower by-pass and sharper separation improve breakage rates and throughputs. An initial model of the screen is proposed.

Jan 1, 2014

By W. Yao, M. L. Li, R. Cui

"The purpose of this research is providing a flotation process for recovery of lead in lead silver residues from a zinc smelting plant with a new hydroximic acid collector (HOC). The collecting ability and reaction mechanisms of HOC were investigated based on pure mineral flotation tests and analysis of zeta potential. The pure anglesite flotation tests showed that HOC has a good collecting ability for anglesite. Zeta potential measurements proved that HOC adsorbed on anglesite surface physically and chemically. The lead-silver residues in a zinc smelting plant with lead grade about 17.5% was used as raw material for flotation tests. The results showed that under the conditions of pH adjusting agent lime 500g/t, inhibitors sodium silicate 2000g/t, collector HOC 1500g/t, frother alcohol oil 75g/t, the grade of the lead concentrate can be reach 47.18% and the recovery was 76.39% by one roughing-one scavenging-three cleaning and middles back to the flow-sheet in turn after the lead-silver residues were washed by two stages of cleaning-filtration.INTRODUCTION Nowadays, with the increasing exploitation of natural mineral resources, more and more secondary resources should be researched and used for the valuable metals. Hydrometallurgical zinc leaching residues, which contain a considerable amount of zinc, lead, silver and other minor valuable constituents, is a typical and abundant secondary resources (Zhang et al., 2011). A huge quantity of zinc leaching residues (ZLR) had been produced per year (Jiang et al., 2017).This residues not only occupy precious land but also threaten the environment because of the dissolved heavy metals especially in rainy days (Han et al., 2014). Consequently, it is urgent to develop an effective and clean method to dispose this residues which can benefit not only in economical but also in environmental (Jha et al., 2001)."

Jan 1, 2018

By E. A. Brocchi

This work is dedicated to the chemical treatment of a typical EAF dust by chlorine content agents. The residue contains 48% Fe2O3 and 28% ZnO mainly in the franklinite structural form. The others less compounds are: 4.00% CaO, 2.60% MnO, 2.20% MgO, 1.08% PbO, 0.36% Cr2O3, 0.21% B2O3, 0.03% CdO and 0.01% NiO. The experiments purpose is selectively to remove zinc from the residue leaving the iron behind. Thermodynamics studies have indicated some roasting possibilities. The experimental results have shown that both HCl leaching and carbochlorination will remove iron and zinc without any selectivity. However, either the chlorine or the calcium chloride roasting seems to form, preferentially, the zinc chloride. So, it will be presented how the EAF Dust can be treated by the using of chlorine roastings process such as carbochlorination in order to separate the zinc and iron present in the frankilinite, main EAF dust content.

Jan 1, 2014

By Ricardo Montero

At this time, over 300 tons of Au are used in electronic equipment each year with other precious and strategic metals such as Ag, Pt, Pd, Cu, Nb, Ta, etc. After the use-phase, the electronic devices become electronic waste (e-waste); consequently it is important to consider e-waste as a secondary supply for recovery of these metals. One of the most important components is the printed circuit boards (PCBs) because the amount of their precious metals is ten times higher than rich precious metals bearing ore. This paper presents the recovery of Au, Ag, Cu and Nb from PCBs of discarded computers using leaching column technique. The amount of these metals in used PCBs was: 613 g/ton of Au, 1515 g/ton of Ag, 36 g/ton of Nb and 23.4 % of Cu. The PCBs were crushed with a hammer mill until reaching a particle size between 3.33 mm to 0.43 mm. Then, it was leached with sodium cyanide solution in a glass column using the following conditions: sodium cyanide concentration 4 g/L, flux 20 L/kg PCBs day, pH between 10.5 to 11 and leaching time 15 days. Every day, after leaching, the pregnant solutions passed through a column with activated carbon to complete the closed loop system. The following recoveries were obtained: 46.6% of Au, 51.3% of Ag, 47.2% of Nb and 62.3 % of Cu. The products obtained are: a) loaded carbon that contains the desired metals and b) processed PCBs with precious metal contents. A preliminary technical-economic study shows the feasibility to create a small-scale PCBs recycling plant. The initial investment is on the order of US$ 155 639, considering the recovered metals from loaded carbon. The internal rate of return for 10 years period (IRR) and net present value (NPV) estimated are 27% and US$ 105 926 respectively. Keywords: printed circuit boards, recovery, precious metals, niobium, leaching column

Sep 1, 2012

By S. Patra, R. Venugopal

"The quality of pellets produced is affected by quality anssastd quantity of green pellets, amount of addition of binders, type of binders added, amount of moisture added along with the other variables like rotation, inclination and fineness of feed. The green pellet quality depends upon chemistry, mineralogy and granulometry of fines used for pellet making, the feed size, its moisture content and porosity. During firing of green pellets ingredients present within reacts to form different phases and microstructure. So in turn physical and metallurgical properties of pellets are influenced by amount and type of binder and flux addition, induration time and temperature. During iron making process, the metallurgical properties of fired pellets are decided by the type and amount of these phases and their chemistry. Green pelletizing and induration studies have been already carried out with hematite ore fines. Indian iron ores of high alumina content showing different pelletizing characters, these studies can’t be directly interpreted. The main objective of proposed research work is to understand the green pelletizing process and determine the water bentonite interaction at different levels. Detailed investigation on swelling behavior of bentonite and microstructure of the green pellets of iron ore fines from SAIL captive iron ore fines from the Barsua in the state of Odisha. To convert these ore fines into pellets, the key raw material, additives and process variables that influence the pellet quality needs to be identified.INTRODUCTION Pelletization is the unit operation of agglomerating iron bearing fines (generally below 150µ with 65-80% passing 40µ) by tumbling in horizontal rotating drums or inclined discs, (Sivrikaya and Arol, 2013; Bhuiyan et al., 2011; Forsmo et al., 2006; Sastry et al., 2003) and the pellets are approximately spherical lumps formed by this process in presence of water and binder, on subsequent induration at 1300°c (Sivrikaya and Arol, 2014; Sivrikaya and Arol, 2013; Sivrikaya and Arol, 2012; Sivrikaya and Arol, 2010; Sastry et al., 2003; Kawatra and Ripke, 2003; Iveson, 2001a; Iveson, 2001b)."

Jan 1, 2018

By Arkady Senchenko

At present, there are different traditional and modern methods for ore grindability evaluation. The correct and rational approach to sampling, testing methods and mill sizing enables one to design a workable technology. This paper contains TOMS institute experience in different grinding indices determination over the last 7 years (SAG Design Test, BWi, CWi, RWi, and other). Mill sizing examples and circuits modeling for the projects in Russia and Kazakhstan are considered. Keywords: ore grindability, SAG Design Test

Sep 1, 2012

By N. Pajunen

The basic objectives of current EU waste policy are to prevent waste and promote re-use, recycling and recovery to reduce negative environmental impact (2008/98/EC). In this paper, we focus on drivers and barriers for sustainable development by decreasing amount of waste and increasing material efficiency. Main target is to understand what are the most efficient drivers for environmental friendly decision making for reasonable consumption and use of raw materials. Environmental control instruments usually mean those actions the regulatory authority uses to control and limit environmentally harmful behavior of companies. A major change in the environmental control system took place in the 1980s with the focus moving from specific environmental issues to the environment as a whole. The environmental control system i.e. the legal (administrative), economic and informative instruments focuses on prevention. Before and still, the legislation is one of the main drivers in improving material efficiency. In this paper, we focus on drivers and barriers for effective industrial material use, and mainly on drivers. The objective of this study is to analyze how the drivers are working and are there any possibilities to influence on those. Our aim is also to introduce few examples of the existing supply chains and the drivers for better environmental performance and material efficiency. These examples are also compared with ideal reference scenarios. Our main research question in this article is: ?Are the financial issues the most important driver for environmental friendly strategic decisions?? In addition, retell the story from another perspective: ?The most important barrier for environmental friendly innovations seem to be the investment cost, the high risk involved in committing capital to unproven technology.? Other drivers, like the corporate social responsibility, stakeholder pressure, and general public pressure, will also affect the final decision. This article is based on research projects and literature. Keywords: drivers, decision-making, environmental management, saving primary raw material, material efficiency, sustainable production, critical raw materials

Sep 1, 2012

By Osvaldo A. Bascur, J. Pat Kennedy

"The profitability of mining and metallurgical operations continues to lag behind that of other industries despite the technical advances that have occurred in recent years. A primary reason for poor performing in this economic sector is the lack of integration of mining and metallurgical information. The mine cut-off grade can be optimized if mining and metallurgical engineers have the data to optimize milling for the type of ore in hand.Integration of mine transactions, stockpile inventories, process flows and assays is the key to determining the economics for each blast strategy in a mining site. Real-time information from manufacturing assets greatly affects the profitability and flexibility of a company, but gross errors from faulty sensors, inaccurate instrument calibration, or incorrect process models may corrupt actionable information. New software tools can model the process, sift through available data to identify and eliminate gross errors, and use statistical data reconciliation to create materially balanced and consistent readings. The reconciled data is unified for use by both monitoring and decision making processes.Creating a real-time information environment where upgrade and change are allowed is becoming an accepted methodology to accelerate and simplify the integration of applications such as production monitoring, equipment performance management and yield and inventory management.This paper describes the data integration requirements in a mine, concentrator and port for unification of the redundant data. The capture of the mining events, stock pile management and the metallurgical information is the base requirements for a dynamic environment to reduce the overwhelming amount of information to unified set of information. Part of any decision support program should entail these results to continuously improve the measurement system to address the costs in mine and milling the ore."

Jan 1, 2003

By Z. L. Huang

A new porous apatite product was prepared using phosphorite from Yichang China by a tem-plate-directed method in self-made reaction equipment under constant temperature and pressure. The product was characterized by XRD, FT-IR and SEM. The results showed that the product was a kind of micrometer porous sphere three-dimensionally structured by apatite nanoflakes, that the average thickness of nanoflakes was about 50 nm, that the average pore size was about 1.2 µm and that the particle average size was about 20 µm. Great amounts of Ca2+channel, high special surface area and regular spherical shape show the potential promising applications of this special porous apatite product in the fields of catalyst, medication, chemical engineering and environment engineering

Jan 1, 2014

By Zhang Zhonghan

A domestic tungsten-tin ore presents very complex property. How to effectively recover the scheelite, wolframite and cassiterite in the ore has long been a difficult problem to be solved urgently. On the basis of process mineralogy study, a main flow-sheet for effective recovery of tungsten-tin minerals has been developed, which including ?fine grinding of feed?bulk flotation of all sulfides followed by their selective separation?iron recovery by LIMS?tungsten-tin minerals bulk flotation using new technique developed by our institute?tungsten-tin recovery by gravity from above tungsten-tin bulk flotation tailings?. As for the treatment of tungsten-tin bulk rougher concentrate, several flow-sheets of tungsten-tin separation by direct hydrometallurgy or a flow-sheet consisting of scheelite cleaning at elevated temperature followed by the gravity separation of scheelite cleaner tailing?separation of wolframite from cassiterite by dry HIMS or by direct hydrometallurgy are developed. For a low grade head ore, all valuable sulfide, magnetite, scheelite, wolframite and cassiterite are recovered with satisfactory in lab scale test. Keywords: micro-fine cassiterite, tungsten-tin bulk flotation, gravity separation-flotation-dry HIMS combined flow-sheet, hydrometallurgy

Sep 1, 2012

By Y. S. Li

The life cycle assessment method is applied to investigate the environmental impacts of cop-per-slag and copper-ore concentration process. Some environmental load data of copper production are obtained. The result indicates that damage level of human health, ecosystem quality and re-sources respectively is 0.174, 0.0203, 0.246 in the copper-slag concentration and 0.112, 0.0136, 0.299 in the copper-ore concentration. Environmental impact of copper-slag production (0.44) is more than that of copper-ore production (0.42), but can meet the environmental protect demand. With domestic copper concentrate supply gap enlarging, recovering copper from slag will lead to a significant improving of resource utilization and development of circulation economics.

Jan 1, 2014

By Evgeni Visariev

In Copper smelter Aurubis Bulgaria, the copper in slag from the Flash furnace and the Converters is recovered by flotation. The scheme of slag processing is crushing, two stage grinding (autogenous and ball) and flotation. Till 2010 the grinding cycle in the plant was in two stages ? the first stage was AG Mill 70?23 working with a classifier and the second stage was ball mill 3.6/5.5 working with a hydrocyclone. In 2010 a new AG Mill 65x78 with hydrocyclone was put in operation in order to increase throughput of the plant. The second stage of the grinding cycle is with the same ball mill. The Old AG mill processed 55-60 t/h slag with particle size -0.071 mm 75% or over 75 t/h with particle size -0.071 mm 35-40 %. The new AG Mill was designed for throughput 105 t/h with particle size -0.071 mm over 70 %. After the start up there were some problems with the equipment ? block up of AG Mill?s grate and pumps for feeding of the hydrocyclone. For optimization of the process a lot of general tests were made. One of the main problem was a wearing of the sand nozzles. Different materials (rubber, ceramic, metallic) for the sand nozzles were tested. The openings of the grate were changed. This paper presents: ? the optimal technological parameters of the old and the new working scheme; ? how the technological parameters of the new working scheme change when the hydrocyclone works with different nozzles; ? the effect of the change of the grate openings; ? the problems with the increase of the circulating load; ? a final decisions for improvement of the grinding cycle work. Keywords: spigot, wearing, classification, effectiveness, circulating load, autogenous, mill

Sep 1, 2012

By M. Kalicinski, M. Lyssyy

"Access to information is a key component for making improvements to any process. This is particularly true for all aspects of the iron mining and steelmaking process. The ability to make rapid control decisions can significantly influence process outcomes, including ensuring product specification, mining quality, transportation limits, upgrade factors, waste bypass and direct shipping, among many others. While traditional laboratory methods provide feedback for such processes, having access to analysis results in real-time can lead to positive reactive and predictive control decisions to be made rapidly, leading to significant improvements throughout the process. Scantech has been designing, manufacturing and supplying technological products to the minerals industry since 2002 to enable the availability of such real-time information to a mine or plant, with the benefits being enjoyed by a wide range of operators. This paper provides a summary of the available technologies used in the iron ore and steel industries, as well as providing case studies of their use in African and Australian iron ore and European steel, as well as a description of the potential benefits of a range of analysis equipment.INTRODUCTION Access to information is critical for any process, and is a fundamental component for making process control decisions. In order to yield effective processing outcomes, it is important for that information to be readily available, preferably as quickly as possible, and to be as accurate as possible. While speed and accuracy are often traded off against each other, there are numerous technologies available in a processing environment that allow for both rapid flow of information and a high level of accuracy. The use of on-belt analysis equipment has a long trusted history of use in a number of mining and processing environments and industries, providing information such as elemental composition and grade of conveyed materials, moisture content, waste proportion and energy information. Australian company Scantech has been a provider of such equipment since 1981, and has become an industry leader in both the supply and development of on-belt analysers across a range of industries."

Jan 1, 2018

By Y. Q. He

The dynamic behaviors of the air bubbles in the dense gas-solid fluidized bed have a significant effect on the performance of dry coal separation. The combined method of experimental measurement and numerical simulation were conducted to conduct the research of the mean diameters and rising velocities of the bubbles in the fluidized bed. The calculation models of mean diameter and rising velocity of the single bubble were proposed. The results indicate that the models of the mean diameter raised by Rowe (1976) and the rising velocity raised in this work could be used to predict the bubble dynamic parameters in gas-solid fluidized bed. With the Geldart B type of magnetite powder as the medium solids and while the gas velocity of 1.5Umf=U=2.2Umf, the mean bubble diameter along the bed height is 36mm<Db<45mm, and the mean rising velocity of the single bubble is distributed in 40~65cm/s. The results of experimental measurement, numerical simulation and model predication provide well agreements finally. Based on the uniform fluctuations of air bubbles diameters and their rising velocities, the separation experiments of 50~6mm dry coal using the mixture of 0.3~0.15mm magnetite powder and <1mm fine coal as medium solids were carried out. The results show that the probable error, E is 0.06, which indicates a good separation performance by using the gas-solid fluidized bed. Keywords: dense gas-solid fluidized bed, bubble dynamic behaviors, numerical simulation, separation performance

Sep 1, 2012

By P. Braga, A. Chaves, S. França, A. Luz

"In Brazil, there are no official reserves of molybdenum, and the unofficial reserves are modest. Therefore, the molybdenum ore (molybdenite) produced as a co-product or by-product of emerald mining in the region of Campo Formoso, BA, has arisen as the only economic option. The flotation process is commonly used in Brazil for the recovery of molybdenite from emerald mining tailings, but it produces low-content molybdenite concentrates, thereby resulting in a product with low economic value. The molybdenite concentrate produced in Campo Formoso contains 83.5% MoS2 (50% Mo), which is less than the international standard product that contains > 90% MoS2 (54% Mo).This low value is due to the presence of talc, which is a naturally hydrophobic mineral that is also floated with the molybdenite during the flotation process. Separability studies were done in a Partridge-Smith cell using dextrin and quebracho as a molybdenite depressor in solution at different concentrations and pH values to produce a technical-grade concentrate (i.e., 90% MoS2). These basic studies were accompanied by measurements of the zeta potential and contact angle, which was determined by the capillary rise method. The results of these floatability studies were used in bench flotation tests, which were performed in a Denver laboratory flotation cell. A molybdenite concentrate of 93.4% MoS2 was obtained when dextrin was used at a concentration of 100 g/t."

Jan 1, 2014

By N. Vorob?ev-Desyatovskii

The process of gold(I) adsorption on activated carbon (AC) from aqueous Na[Au(CN)2] and the state of the adsorbed gold cyanide complex on the adsorbent surface was investigated by photometry, XPS, XANES methods. By DFT method, quantum-chemical calculations were performed of the gold cyanide species on activated carbon surface. It was established that the binding of gold(I) with the surface of carbon involved several simultaneous processes governing the selective adsorption of gold(I) from the cyanide solutions.

Sep 1, 2012

By Y. C. Liu

Arsenic bearing copper-gold ores deposit have been found in most areas of China, especially in southwest. Due to the very closed association between arsenic, copper and gold, conventional flotation and cyanide leaching process may not give positive results. An arsenic bearing copper-gold ore in Sichuan province ,with gold grade of 10.12 g/t, 0.6% Cu and 0.14% As, is characterized by superfine grains with -40 microns fraction accounting for 70.9% and the gold enwrapped mainly by pyrite and tennanite accounts for 34.31%. Arsenic in this ore occurs in isomorphism, deposited in tetrahedrite. The ore was processed primarily in two stage flotation to get copper bearing gold concentrate and pyrite bearing gold concentrate respectively, and sequentially processed by leaching. Under the pressure of 300 KPa and 110~115 ?, the copper-gold concentrate was leached by an oxidizing and catalyzing leach agent then copper and gold were separated from each other in leach solution. The pyrite bearing gold concentrate was processed by cyanide leaching with the leach residue as sulfur product. The test results showed that copper recovery was up to 88.89%, gold recovery up to 89.18% and sulfur recovery up to 92.64%.

Jan 1, 2014

By W. Y. Gao

Diaojuntai Concentrator adopts a process of low intensity and high intensity magnetic separation and anionic reverse flotation, with all the concentrate from magnetic separation being treated by re-verse flotation to obtain a qualified final concentrate. The high reagent cost and energy consumption of the reverse flotation have led to a high concentrate cost. The test research on reducing the feed to the reverse flotation was therefore carried out. Based on the study of the properties of the ore sample, the concentrate of low intensity magnetic separation was screened at 0.076 mm and the undersize fraction was concentrated by concentrator with gravity and magnetic field. The results show that a qualified concentrate can be obtained at various rising current rate, pulsating current and power-on style, with the operation rate over 85%. The extraction of some part of qualified concentrate from the concentrate of low intensity magnetic separation by magnetic separation can reduce the feed to the reverse flotation by about 35% so as to reduce the production cost of concentrate.

Jan 1, 2014

By Z. S. Abisheva

Results of the study targeted to development of universal acidic-extraction-precipitation technology for gallium recovery from the sublimates are presented in the paper. This will let to utilize a new non-traditional source for gallium production. Phase composition of gallium containing dust was studied. Forms of gallium in the sublimates were determined. The main form is Ga2O3, however, GaP form is also present in the cottrel dust and Na5Ga3F14 form is present in the dust of aluminum electrolysis. The possibility of gallium concentration was established via secondary pyro-selection of the dust. Kinetics of interaction of dust components with sulfuric acid was studied. The products of the interaction subsequently were leached with water. Optimum conditions for direct leaching with HCl and H2SO4 were determined providing gallium recovery from the cottrel dust and the ash carry outs up to 95 %. Gallium recovery from the primary dust and the secondary dust of aluminum electrolysis was at 52; 64 % and 63; 83 % respectively. Effect of Fe, P, K, Na and Al admixtures for gallium extraction from hydrochloric acid solutions was studied. It was shown that gallium chloride complex (GaCl4-) is extracted into the organic phase from the following acid mixtures: HCl + H2SO4, HCl + H3PO4, HCl + H2SO4 + H3PO4, HCl + HF. Kinetic regularities of gallium extraction in the system (tri butyl phosphate) TBP ? HCl - Ga were studied using diffusion cell method with agitation. Optimum conditions for gallium extraction from complex hydrochloric acid solutions with TBP were found providing 99.9 % recovery and separation coefficient for gallium and iron (III) of more than 25 in one stage. Sodium hydroxide and water were selected as reagents for re-extraction of gallium from the organic phase. Different options for disposal of by-products that are formed in the processing of cottrel dust, ash sublimates and dust of aluminum electrolysis were proposed and tested. Keywords: gallium, kinetic, sulfatization, leaching, extraction, technology

Sep 1, 2012

By P. Ying

An auxiliary system connected with SEM-EDX for rapid identification of mineral and rock sample has been developed. With the aid of a synthetic spectrum library created, using the compare and match techniques provided by INCA software in EDX the mineral or rock sample names for refer-ence can be given at the same time analyzed.

Jan 1, 2014