Search Documents

By Yahia M. Al-Smadi

Effect of lateral loading against existing sheet pile wall and distribution of gravity loading due to various number of construction loading scenarios were studied. The objective of this effort was to determine the loading case that permits the contractor to utilize a 400 ton crane at the specified location with the existing limitation imposed on site. Staged analysis was determined as the methodology that will more accurately predict the exiting and additional stress due to the impose crane loading. A reliable and robust analysis (ANSYS) software was used to complete both 2D and 3D finite element model and analysis. Analysis model parameters such as material properties, non-linear behavior of the soil, and meshing are presented and discussed. At the conclusion specific range of crane operation and pick weights operating on existing concrete mat supported on top of an existing tunnel was reviewed and deemed acceptable.

Jan 1, 2010

By Lee S. Vanzler

Atlantic Wharf involved the construction of a six-level underground parking garage and a 32-story high rise tower along the historic Boston Harbor waterfront. The site, historically known as ?Russia Wharf,? consisted of filled land initially created in the late 1800s by extending the shoreline toward the harbor as the urban population and land needs grew to support expansion of commerce and trade. Redevelopment required solutions to address relics of waterfront structures (granite block seawalls, piles, and piers), weak subsurface soil conditions, tidal groundwater levels, and contaminated soils resulting from previous site usage and filling. The foundation system, consisting of drilled shafts with column loads up to 14,000 kips (62,272 kN), concrete diaphragm wall (slurry wall), and up-down construction methodology, was chosen to address these factors. As a prerequisite for development, selected portions of the façades of the former historic buildings were required to be preserved, protected, and incorporated into the final building configuration. The historic façades were temporarily braced and supported prior to the demolition of the buildings and commencement of below-grade construction. This paper will describe the considerations in the selection of up-down construction methodology along with a discussion of the design and performance of the concrete diaphragm wall and drilled shaft foundations. Up-down construction methodology shortened the overall construction schedule while addressing the lateral bracing requirements for the concrete diaphragm wall and restrictive ground movement tolerances to protect adjacent structures. Below-grade construction was completed in March 2010, and the building was opened for tenant occupancy in January 2011.

Jan 1, 2011

By Patrick van der Schaaf

"During 2016, foundation piling works were completed to allow for the construction of a production and storage/handling terminal in Rotterdam. It is there that steel foundations will be produced for offshore wind farms and the oil and gas industry. Several Dutch contracting companies were involved in constructing: foundations for an assembly hall, a barge quay and a deep-sea quay wall. For the hall foundations, cast in situ concrete vibro piles were created. Open ended steel casing piles were also installed due to very high cone resistances which made it impossible to perform cast in situ piles in certain areas. The quay wall was constructed with open ended steel casing piles in combination with sheet piles. A deep-sea quay wall was also constructed to provide enough storage area for the offshore mono piles. This project was unique and challenging due to the use of different foundation technologies in challenging circumstances and soil conditions. This paper will give an insight into the Dutch use of varying foundation piling techniques for deep-sea quay wall constructions. It can be concluded that even experienced local contractors can be surprised by variations in soil conditions. It will also show how the contractors adapted to the difficult circumstances.PROJECT OUTLINEThe project consisted of a barge quay near the assembly hall with a length of 500 metres, width of 42 metres and a height of 35 metres, and a deep-sea quay wall 480 metres in length. This paper concentrates on the foundation works for the construction of the deep-sea quay wall. The construction of the deep-sea quay wall consisted of a combination of open ended steel casing piles with a diameter of Ø 1420 mm and a wall thickness varying between 21 and 23 mm. The lengths of the steel casing piles varied between 32 and 37 metres. Between the steel casing piles triple PU 28 sheet piles were installed with lengths varying between 26 and 29 metres. In the Netherlands, a combination of open ended steel piles and sheet piles is known as a “combi wall”. For the deep-sea quay wall a steel combi wall was shored with steel H- section profiles that were driven in a raked position whilst being injected with grout, so called MV-piles. The MV piles for this project consisted of steel HEB 600 sections with lengths from 52 up to 59 metres and were installed with angles varying between 42.5 and 47.5 degrees. For a detailed overview regarding the project specifications reference is made to table 1 which is presented below."

Jan 1, 1900

By David K. Crapps

The drilled shaft load tests at Port Orange were part of a demonstration project sponsored by the Federal Highway Administration (FHWA) and the Florida Department of Transportation (FDOT). Three load tests were conducted. Test 1 was a conventional test with the test shaft loaded from the top. Test 2 included an Osterberg load cell at the tip and a conventional load test from the top. Test 3 used an Osterberg load cell at the tip of a production drilled shaft. All three test shafts were socketed into limerock and were carried to failure. This paper describes the test program and presents a summary of the test results. Figure 1 presents some photographs of the load test setups and Figure 2 shows the location of the drilled shaft load tests. SITE CONDITIONS The Port Orange Bridge is located on US A1A over the Intercoastal Waterway in Port Orange, Florida (south of Daytona Beach). The new bridge will provide four lanes of traffic with a 65 foot vertical clearance for Intercoastal Waterway traffic. The channel and flanking piers will be supported by 54" drilled shafts socketed into the rock. The bridge is being constructed in two phases. The southern half will be completed first, the old bridge removed and then the northern half will be constructed. The first phase is scheduled to be opened to traffic in October 1989. Each of the four piers near the channel will be supported by 12 drilled shafts with 6 shafts per pier being constructed in each phase.

Jan 1, 1989

By C. Guney Olgun, Mohammad Khosravi, Daniel W. Wilson, Deepak Rayamajhi, Scott A. Ashford, Shuji Tamura, Ross W. Boulanger

"Dynamic centrifuge tests were performed on unimproved and improved soil with soil-cement column models. The reinforcing effect of isolated soil-cement columns for reducing liquefaction potential and ground deformation in improved soil were investigated. This paper presents the observed acceleration, pore pressure, and settlement responses under an earthquake base motion for both unimproved and improved soil models. In addition, lateral reinforcing effects of soil-cement columns were also investigated in terms of site stiffening effects and the increasing natural frequency of improved soil. The test results show that the soil-cement columns were rather ineffective in preventing liquefaction triggering in improved soil and in significantly reducing the magnitude of the resulting soil settlement compared to the model with unimproved soil profile. Furthermore, the predicted natural frequency of the improved soil profile estimated using existing design equations is shown to be significantly higher than the observed natural frequency inferred from centrifuge tests results. These design equations assume shear strain compatibility between the columns and the surrounding soil. On the other hand, revised design equations that account for shear strain incompatibility between column and surrounding soil are shown to give reasonable estimates compared to the observed natural frequency of the improved soil model.INTRODUCTIONGround improvement using stiff columns (e.g., stone columns, deep-soil-mixing columns, and jet-grout columns), are often used in practice to reduce liquefaction potential (and associated deformations) in loose soil sites. Typically, saturated silty soils are difficult to densify or drain rapidly due to their lower hydraulic conductivity, so densification and drainage techniques of improvement are often found to be ineffective. Instead, the shear reinforcing mechanisms of stiff columns are considered effective for reducing the seismic stresses and strains, and thereby reducing liquefaction potential in the enclosed saturated silty soils (Baez 1995, Adalier and Elgamal 2004, Mitchell 2008)."

Jan 1, 2015

By Prasanta Paul, Aminul Islam

"Nhava Sheva (India) Gateway Terminal Private Limited proposed to construct a container terminal yard, comprising a back-up area at Jawaharlal Nehru Port Terminal (JNPT), Uran, Maharashtra. The proposed container terminal yard is located on a recent reclamation on the Thane Creek, which was developed by land-based reclamation method. The underneath soft marine clay was treated, using vertical band drains and placement of surcharge upon.Settlement of the reclamation during its construction was monitored using settlement plate installed at +4.8m CD elevation which was above the highest high water level.This paper examines the settlement behaviour of the reclamation during the ground improvement works. The geotechnical parameters are back-analyzed by the authors from the field settlement results and the concerned preloading details. The back analyzed coefficients of consolidation due to horizontal flow (Ch) are compared with laboratory determined parameters and the estimated value, using Asaoka Method (1978). The authors also studied field compression ratio [CR= Cc/(1+e0)] vs. the compression ratio determined by laboratory test using back-analysis method.1. INTRODUCTIONNhava Sheva (India) Gateway Terminal Private Limited proposed to construct a container terminal yard, comprising a back-up area of approximately 27 hectares, complete with associated buildings and services on a part brownfield/ greenfield site. The back-up area shall include a heavy duty block paved pavement with band beams for electric Rubber-Tyred Gantry Crane (eRTGC) alongwith surface water drainage system and other services including area lighting, provision of fire-fighting facilities , sources for potable water and power.Based on the Employer’s Requirement and the available geotechnical investigation report, ground improvement scheme is designed by the construction contractor. Ground improvement works included the installation of prefabricated vertical drains and subsequent placement of surcharge for accelerating the consolidation of the underlying soft marine clay."

Jan 1, 2015

By Seth H. Hamblin, John E. Regan, Dimitrios Palantzas

"Through reliability-based calibration of larger pile load test databases, recent developments of the Load Resistance Factor Design (LRFD) methods, which include geotechnical load and resistance factors for deep foundations design, have advanced the state of practice for geotechnical engineering. These load test databases upon which the current geotechnical load and resistance factors have been developed are limited, however, and do not provide sufficient data to support the development of resistance factors for uplift (tension) pile capacity. As such, some recommended resistance factors for uplift capacity estimation methods are simply derived by reducing the recommended resistance factors for piles in compression by a factor of 0.10.The results of three (3) tension loading tests performed to failure on 508 mm (20- in) square precast, prestressed concrete piles, driven though granular soil in southeastern Massachusetts, are presented and compared to static pile capacity calculations and dynamic analyses performed using the Pile Driving Analyzer (PDA) during installation. These results are presented along with current recommended LRFD resistance factors for driven piles under uplift (tension) loading conditions. These comparisons offer an assessment of the applicability and limitations of current resistance factors methods for piles under uplift loading and may be useful additions to the existing database for future calibrations of LRFD resistance factors for driven prestressed concrete piles in sand.IntroductionIn 2010, two (2) natural draft cooling towers were constructed by Kiewit (Kiewit) Construction Company of Woodcliff Lake, New Jersey at the Brayton Point Power Station in Somerset, Massachusetts. These massive 500 foot tall, 400 foot diameter cooling towers were designed to convert the existing “open loop” system into a “closed loop system” thereby dramatically reducing the thermal impact to Mt. Hope Bay.Based on design guidance from the German VBG Design Code and the Massachusetts State Building Code (MSBC), tension (i.e. uplift) and lateral loads due to wind loads and design seismic events represented the critical loading conditions.Weighing approximately 190,000 kips upon completion, the cooling tower loads are transferred to 44 foundation nodes (i.e. pile caps) evenly spaced along ring beams which run the circular perimeter of each tower base. Each pile cap node was designed to resist a 2,000 ton compression load, 200 tons in tension (i.e. uplift), and 600 tons in the lateral direction."

Jan 1, 2015

By Matthias Pulsfort, Jiarui Du, Torsten Wichtmann, Achim v. Blumenthal, Diethard König, Rowena Verst

The influence of the interaction between support fluid and soil, e.g., filter cake formation, on the shear stress transfer in the soil-concrete interface of diaphragm walls and bored piles is still controversially discussed. Actual research on the soil-concrete interface using bentonite suspensions indicates that shear stress transfer is underestimated by existing standards. Investigations on the soil-concrete interface using polymer solutions are rare. Therefore, complementary field investigations and systematic laboratory studies were conducted to analyse the soil-concrete interface using both bentonite suspensions and polymer solutions. Thickness and composition of real-scale filter cakes were investigated on several slurry wall construction sites, where bentonite suspensions were used. Direct shear tests (60 mm x 60 mm) were executed for soilbentonite mixtures with varying amounts of bentonite and different granular fines representing a realistic bandwidth of in-situ filter cake compositions. Larger direct shear tests (300 mm x 300 mm) with preceding horizontal penetration, subsequent vertical tremie concrete placement, and filter cake consolidation were performed using both bentonite suspensions and polymer solutions. The results support the view that shear stress transfer in the soil-concrete interface can be described by a wall friction angle in a range of 25° to 30° for bentonite suspensions and between 35° and 40° for polymer solutions in non-cohesive soils.

May 1, 2022

By William M. Dalrymple, William P. Owen, Benjamin S. Rivers

For the California Department of Transportation (Caltrans), geophysical applications have played an important role as part of a successful multidisciplinary approach to subsurface characterization for the design of high value structures. Since at least the 1950’s, geophysical methods have been deployed to guide the exploration drilling program and to maximize the return on drilling investment by increasing the amount of data obtained from test borings. Geophysical applications saw increased use beginning in the 1990’s, during the seismic retrofit of the state’s toll bridges and the replacement of the west span of the San Francisco-Oakland Bay Bridge. Over the intervening years, increases in computing power and increasingly sophisticated commercial off-the-shelf software applications have allowed Caltrans to leverage advancements and perform geophysical investigations of increasing complexity and scale. Ultimately, the goal of these efforts is to maximize return on investment, whereby increased investigation costs at the design phase are offset by reduced uncertainty regarding subsurface conditions, leading to reduced cost overruns related to change orders and unforeseen site conditions during construction. These objectives are consistent with the recent Every Day Counts (EDC) initiative to incorporate Advanced Geotechnical Methods in Exploration (A-GaME) into routine engineering practice. Caltrans is an implementation partner of the A-GaME initiative, and Caltrans’ practices represent a model toward the institutionalized geophysical site characterization practices for other transportation organizations. The authors provide a retrospective on 70 years of experience with geophysical applications for transportation infrastructure, with examples and observations on potential future direction of the industry.

By Gerald Verbeek, Erick Baziw

Stone columns are used in geotechnical site remediation to increase load-bearing capacity and reduce settlement of foundations. Stone columns also improve slope stability and increase the shear strength of a soil. A very challenging problem is to characterize the in-situ shear wave velocities from data acquired from Downhole Seismic Testing (DST) after the insertion of stone columns. DST is an important geotechnical testing tool for site characterization that provides low strain (<10-5) in-situ interval compression and shear wave velocity estimates, but the postanalysis of seismic data acquired from DST in the presence of stone columns is very challenging due to the resulting complicated in-situ soil conditions. To obtain the right results it is necessary to use an algorithm that incorporates source wave raypath refraction. Starting with the Normal Moveout Seismic Cone Tomographic Testing (NMO-SCTT) algorithm developed some years ago, this paper outlines the modifications and additions made to this NMO-SCTT algorithm to facilitate stone column site characterization. To dramatically reduce the optimal solution space for the estimated interval velocities the paper also described a priori conditions that are applied based on the unique nature of the stone column site conditions.

By Paolo Cavalcoli, Federico Pagliacci

"As opposed to the static functional recovery of existing structures, the construction of infrastructures in an urban environment, when combined with complex geological situations, often involves building foundation structures, whether circular or rectangular in section, through rock formations or chaotic strata (sand and gravel with cobbles). Until a few years ago, these formations or strata were sometimes an insurmountable constraint on traditional foundation installation techniques. The difficulty in overcoming these geological situations is sometimes added to the increasingly frequent need to reach depths that were unimaginable just a decade ago. These are real challenges for those carrying out these works and for those manufacturing the necessary equipment. There are two main methodological approaches to these problems, that can be summed up in the rhetorical figure of ""David and Goliath"": cunning versus force. In reference to the case studies in this article: the permanent retaining walls for the Copenhagen Metro, and the structural repairs to the Arapuni Dam in New Zealand and the Wolf Creek Dam in the U.S., we will describe the foundations constructed in presence of rock using combined small-diameter direction drilling solutions, associated with their enlargement up to the project’s size, at depths exceeding 300 feet. Finally, a case study will be presented on the implementation of a large cross-section of an excavation in the rock, at depths greater than 800 feet.IntroductionAs opposed to the functional recovery of existing structures, the construction of infrastructures in an urban environment, when combined with complex geological situations, often involves building foundation structures, whether circular or rectangular in section, through rock formations or chaotic strata (sand and gravel with cobbles).Until a few years ago, these formations or strata were sometimes an insurmountable constraint on traditional foundation installation techniques. The difficulty in overcoming these geological situations is sometimes added to the increasingly frequent need to reach depths that were unimaginable just a decade ago.These are real challenges for those building these works and for those manufacturing the necessary equipment. There are two main methodological approaches to these problems, that can be summed up in the biblical figures of ""David and Goliath"": cunning versus force. In the engineering field, the force is summarized in the use of ever-larger drilling equipment in terms of installed power, weight in working conditions, winch and rotary capacity."

Jan 1, 2015

By Vivek Samu, Murthy Guddati

A new method called Effective Dispersion Analysis of Reflections (EDAR) was recently developed to effectively analyze the dispersive waves generated from lateral impact to piles. This paper presents the results of nondestructive length estimation of existing piles through EDAR. EDAR provides a new visualization method for analyzing wave reflections by transforming the response into the frequency domain thus eliminating the need to perform difficult peak picking in the time domain. In addition to being able to analyze dispersive waves, EDAR also incorporates the effects of radiation damping due to the surrounding soil leading to more accurate length estimates. Concrete filled steel tubes of different embedment depths were tested both in laboratory and field conditions. Length estimates obtained were within 10% error margins after careful analysis accounting for the presence of soil effects and effects from pile top reflection.

By Takefumi Takuma, Ali Fayad, Shigeru Kambe

"This paper discusses the unique design and construction circumstances of the cantilevered dual sheet pile walls and the Accordion Sheet Pile Wall for the repair and upgrade of the East Garden Grove-Wintersburg Channel in Huntington Beach, California that was concluded in 2014. It also describes the 2008 Emergency Sheet Pile Project for the same channel. Both projects utilized the Press-in Piling Method for its low noise and almost no vibration advantages.BackgroundThe East Garden Grove-Wintersburg Channel is part of the Orange County Flood Control District (OCFCD) and is operated and maintained by OC (Orange County) Public Works (see Figure 1 for its location). The channel, referred to as OCFCD facility # C05 (C05), had suffered significant toe undercutting and slope erosion of its levee due to a series of storms. These began after the facility was constructed in the 1960’s and culminated in 2005. Consequently, the levee was deemed significantly deficient and was eventually declared as a local emergency in 2007. C05 was an incised channel and its levee was constructed primarily from native materials. Operation and Maintenance (O&M) personnel notified the design staff at OC Public Works to be aware of major consequences associated with the dilapidation problem in the most downstream reach of the channel in the vicinity of the Bolsa Chica Wetlands Restoration Project. In 2007, the Orange County Board of Supervisors declared a local emergency to fix the levees with sheet piles to be driven by the Press-in Piling Method, hydraulic pushing piles into ground by holding onto previously installed piles. The project that ensued represented the first in-tandem use on the West Coast of the United States of the Press-in pile driver with its GRB System (Press-in pile driver, a support crane and pile transporter travel on top of already-driven sheet piles). This is further discussed in this paper in the sections titled “Press-in Piling Method” and “GRB System”, respectively. The project repaired approximately 3,800 feet of erosion on the north levee of C05 with 45-foot long cantilevered sheet piles. The sheet piles design constraints are discussed in this paper in the section titled “C05 2008 Emergency Sheet Pile Project (Phase 1)”. Between 2012 and 2014, another mile’s worth of levee reach was improved with the Soil-Mix-Sandwich (SMS) Method. This concept consisted of deep soil cement mix (DSCM) columns sandwiched within the dual rows of sheet piles. Additional details on the SMS, its DSCM construction, and its hybrid geo-structure design concepts are well beyond the scope of this discussion, which is primarily focused on sheet piles. Instead, the interested reader is referred to two papers on the SMS and its DSCM metrics (Fayad, 2015; and Arora, et al., 2015). These were presented and published in the Proceedings of the Deep Foundations Institute (DFI) 2015 Conference on Deep Mixing. Hence, in the section of this paper titled “C05 SMS Dual Sheet Piles Project (Phase 2)” only the sheet pile design constraints of the SMS are covered. Finally, in the area where the project traversed the Alquist-Priolo zone of the Newport-Inglewood tectonic fault, an expandable and deflectable sheet pile wall was used to isolate the flood channel from the Bolsa Chica wetlands. Its details are addressed in the section titled “C05 Accordion Sheet Pile Wall (Phase 2)” of this paper."

Jan 1, 2017

By Masaki Kitazume

"Many earthquakes take place every year in Japan, in which the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake induced both a humanitarian crisis and massive economic impacts. As liquefaction which occur in a loose and saturated sand layer, induces quite large damages of infrastructures, the importance of liquefaction mitigation has been emphasized to minimize earthquake disasters for many years. Many kinds of ground improvement techniques based on various improvement principles have been developed for earthquake disaster mitigation. Among them, the grid type deep mixing method has been often applied to liquefaction mitigation. In the method, the stiff grid walls are constructed by mixing the soil and binder in-situ, which are expected to restrict the shear deformation of the soil within the grid walls so that the pore water pressure generation can be remained small. The high applicability of the method was confirmed in several earthquakes, including the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake. In this paper, the development of the method, some applications of the deep mixing method to earthquake disaster mitigation are briefly introduced. INTRODUCTION In Japan, many earthquakes take place every year in Japan, in which the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake induced both a humanitarian crisis and massive economic impacts. As liquefaction induces quite large damages, the importance of liquefaction mitigation has been emphasized to minimize earthquake disasters for many years. Table 1 shows the amount of damage to port facilities (Noda, 1991). According to the table, the amount of damage when liquefaction takes place is about 20 to 50 times larger than that without liquefaction. This highlights the importance of liquefaction mitigation to minimize earthquake disasters. There are many kinds of soil stabilization techniques developed for liquefaction in Japan. Among them, the deep mixing method (DMM), an in-situ cement stabilization techniques, was developed in 1970s in Japan and has frequently been applied to improvements of clayey and sandy soils (Kitazume and Terashi, 2013). The grid type DMM has been often applied to prevent liquefaction, where the grid of stabilized column walls function to restrict generation of excess pore pressure in the soil within the walls by confining the soil particle movement. The improvement effect of the method was first evaluated in the Hyogoken-Nambu earthquake in 1995 and was also evaluated in the Tohoku earthquake in 2011. In this paper, some successful performance of the deep mixing method to earthquake disaster mitigation in the two earthquakes are briefly introduced."

Jan 1, 2015

By Georgette Hlepas

How often phrases like these have been made by project managers and project teams trying to explain why there has been cost growth, project delays and differing site conditions claims. But does it really take x-ray vision? Do we really approach geotechnical construction projects unprepared for the subsurface that may be encountered because we can't get the answer? Too often our industry seems to think the answer is, "yes." However, this is not because we can't understand the subsurface. All too frequently it is because a choice is made to save money or time by foregoing or shortchanging upfront subsurface investigations. This is accepting a risk at the beginning of the process and realizing it during construction. Case histories have proven time and time again that upfront investment in site exploration and constructing a ground model mitigates risk in design and construction. But how much do we prepare? What level of investigation (or investment) is appropriate? The answer of course, is it depends; how much risk are you willing to take for your project and what are the potential consequences?

May 1, 2022

By Alper Turan

The use of aggregate pier foundation systems has become widespread as the engineering practice moves towards cost-effective ground improvement solutions that provide accelerated construction schedules. Increased bearing capacity, effective settlement control and potential for liquefaction mitigation are commonly acknowledged benefits of aggregate piers. This paper studies the mechanisms by which aggregate piers interact with each other and with the surrounding ground when excited by seismic loads. A particular emphasis was placed on the response of a raft foundation supported on a site improved using aggregate piers. Three-dimensional nonlinear finite element analyses were conducted using commercial software package, ABAQUS. Non-linear soil behaviour is modelled using a three-dimensional total stress-based bounding surface plasticity model, which is able to simulate stiffness degradation and damping increase in the soil. The soil stratigraphy considered in this study was a 30 m deep soil deposit that comprised a very stiff base layer and a shallow soft surficial clay layer. Ricker Wavelet time histories with different frequency contents are used as the excitation force in the analyses. Various area replacement ratios (ARR) for aggregate piers are studied for a square plan layout. The results presented in this study are considered to be of interest to researchers and designers in evaluating the seismic ground response of the sites improved using aggregate piers.

By Satyajit A. Vaidya

This paper presents a case-study in the design and construction of deep foundation element supported mats for two residential towers on an18,000-square-foot site in Brooklyn, New York. Based on site sub-surface conditions, conventional mat foundations bearing on medium dense sand, having an allowable bearing capacity of 3 tsf, were originally anticipated for the 16 and 25-story towers. However, when the tower shear walls were relocated to the edges of the mat foundations due to architectural revisions, the significantly increased mat edge contact stresses applied to the soil subgrade resulted in calculated settlements of a magnitude that would adversely impact the proposed structures and the neighboring/bordering lot-line building and rail transit subway structures. To address this issue, deep foundation element supported mats were designed for the towers. The design was performed as an iterative process involving structural SAFE and geotechnical Plaxis finite element computer analysis to develop a coordinated geo-structural model of the foundation system. Initial presumptive design values of 45 pci and 445 kips/inch were used for the modulus of subgrade reaction and minimum deep foundation element stiffness, respectively. The designed foundation system consisted of 40 and 60-inch-thick mat foundations for the 16 and 25 story towers, respectively. Initially, the deep foundation elements were designed as 50-foot-long, 14-inch-diameter elements installed to sustain a maximum individual compressive load of 250 tons. The final deep foundation element design was subsequently refined to consist of a 48-foot-long, drilled and grouted IBO Titan 103/51 element designed to sustain a maximum load of 167 tons. Subsequent field load tests on the deep foundation elements confirmed element stiffness ranging from 1,040 to 1,530 kips/inch, with measured mobilized side shear of about 29 psi. The mat foundation reinforcement was adjusted for the pile stiffness values determined in the field load tests, and the deep foundation supported mats were constructed. The two towers were subsequently constructed, and have performed successfully.

Jan 1, 2010

By Abid O. Adekunte, David Greentree, David Hilton

"The construction industry is witnessing an upsurge in demand by property developers to have basements incorporated into their residential and commercial development schemes. This is attributable to perceived improvement to aesthetic and commercial values of buildings by underground space, amongst property owners. This trend is compelling more owners of buildings with no basements to explore the possibility of creating underground additional space beneath their existing buildings. The creation of a basement beneath an existing building entails the installation of a reinforced concrete (RC) underpinning system, temporary works, bulk excavation to basement formation level and construction of the basement structure, with associated aesthetic finishes.The L-shaped segmental RC underpins are a common system of choice for such underpinning works. They are multi-functional; providing vertical support to the existing superstructure, providing lateral support to earth and groundwater, supporting temporary and permanent surcharge loads from adjacent structures and services, whilst also forming part of the basement slab. This paper focuses on the first function of the Lshaped RC underpins; capacity under vertical compressive loading from the superstructure. The most common industry approach for the prediction of vertical capacities of L-shaped underpins is the oldfashioned Meyerhof’s (1953, 1963) effective width method, which is based on the traditional bearing capacity theory, whilst accounting for correction factors for eccentricity and foundation depth.The traditional bearing capacity formula is surrounded by a significant degree of uncertainty; estimates are highly user-dependent, as capacity prediction is sensitive to the chosen angle of shearing resistance (?), while there are difficulties in accurately measuring the in-situ ??value of cohesionless soils. In addition, the effective width approach has been shown to be very conservative by many research workers. The segmental RC underpins presented in this paper have been designed with an alternative less conservative method, which involves the use of a recently proposed consistent work-hardening plasticity model calibrated with field-based tests on footings of various aspect ratios and relative embedment in sand. The paper highlights the principles behind underpinning works for urban basement construction, the design of L-shaped RC underpins with the recently proposed plasticity model and the advantages of the method over traditional bearing capacity solutions and pre-existing plasticity models."

Jan 1, 2016

By Garland Likins

The Texas Department of Transportation, now considering using Augered Cast-In-Place (ACIP) Piles (also known as Continuous-Flight-Auger or CFA Piles) in their foundations, awarded a research project to Professor Mike O&apos;Neill at the University of Houston (UH) to study the advantages and potential difficulties with ACIP/CFA piles. ACIP/CFA piles were installed on three sites for UH; they had extra instrumentation and additional measurements by UH staff during installation which are beyond the scope of this paper. Independent visual logging of the pile was done by an experienced inspection firm. The main advantages of ACIP/CFA piles are their speed of installation and their economy. Potential savings are substantial. Disadvantages include an unknown structural condition of the shaft. Inspection is critical, but many simultaneous observations make accurate inspection difficult. Because of resulting uncertainty, many engineers have avoided ACIP/CFA piles in the past.

Jan 1, 1998

By Osamu Taki

The innovative Soil-Cement Mixed Wall Technique emerged in Japan and obtained recognition in the engineering and construction communities in the 1980&apos;s. This technique was introduced to the United States in 1986. It was accepted as the most credible construction technique by the U.S. Bureau of Reclamation for ground stabilization and cutoff wall work in the Jackson Lake Dam Project, Wyoming in 1987 and 1988. It was also accepted as a remediation technique by U.S. EPA for a Superfund Innovative Technology Evaluation (SITE) demonstration on in-situ solidification/ stabilization. The Soil-Cement Mixed Wall Technique consists of mixing in-place soils with cement grout or other reagent slurries using multiple axis augers and mixing paddles to construct overlapped soil-cement columns. The overlapped column panel is then extended to form an underground continuous soil-cement wall for use as a cutoff wall or a structural diaphragm wall for groundwater control and excavation support. By arranging the column panels in various configurations, the technique becomes a versatile tool for stabilization of soft or liquefiable soils.

Jan 1, 1990