Search Documents

By Z. D’Amico

"IntroductionWE HAVE HEARD quite a lot recently on newer methods -of supporting roof, such as roof bolting or the use of metal props and •booms, but, with the exception of roof bolting, these methods are confined mostly to comparatively low, regular seams and even .bolting cannot be used to hold soft sides. Thus, where a seam of coal has great variations in thickness, or where it is faulty, or where the coal sides must be supported, nothing can wholly take the place of timbering with wood. This paper will deal mainly with the method of timbering such a seam, namely, the No. 3 seam mined by Brazeau Collieries, Limited, at Nordegg, Alberta, where the full height of a thick seam is mined in development. However, a few words on one or two other systems practised in Alberta when, in development work, a thick seam is only partially mined, should be of interest.Examples of Timbering in High SeamsThere .are several methods in use today for dealing with high seams of coal. The most popular is to develop the seam by driving road-ways in the coal by some conventional method, usually recovering the full thickness of the seam on the retreat. The following examples illustrate two variations of this method.In Figure I we have a thick •seam of friable coal, with a good roof, pitching about 30 degrees, which is being mined by taking the upper part of the seam in the development work, leaving the •bench coal in place. Figure 1A shows a section through a room."

Jan 1, 1954

By Xian Jian Guo, Lei Li, Hua Wang

Direct smelting of copper concentrate to blister copper has the advantages of energy saving and environmental protection. There has been a lot of effort invested in process development including test work and theoretic analysis in the past half century. However, the process has only been applied commercially to a few smelters that treat chalcocite types of copper concentrate. The main limitation to treating chalcopyrite types of copper concentrate is high copper content in smelting slag and low direct copper recovery. Thus intensive slag cleaning is needed. In this paper, the thermodynamic analysis was mainly carried out for the multiphase equilibrium of direct to blister copper smelting for both chalcopyrite and chalcocite concentrates. The practical problems in direct to blister copper smelting, which are mainly in copper content in slag, are clarified. The operational window of slag composition for different temperatures and oxygen partial pressure for the treatment of chalcocite type concentrates is identified. The process operation optimization for the blending of chalcocite, pyrite and chalcopyrite concentrates was done. INTRODUCTION The extractive metallurgy of copper can be divided into two broad groups of processes, namely, pyrometallurgy and hydrometallurgy, and the former is dominant. About 80% of copper in the world is produced by pyrometallurgy (Christopher et al., 2006). The first stage of conventional copper pyrometallurgy processing is to smelt copper concentrate to copper matte composed of FeS and Cu2S with slagging to remove a proportion of the iron (Gargul, Boryczko, & Bukowska, 2017). The smelting processes include bath and flash smelting. The second stage of the process is to convert copper matte to blister copper. In most cases, the copper matte is converted in Peirce Smith (P-S) converters, which are batch operations (Kubiszewski, 2015). The P-S converting can be divided into two periods, slagging and copper blowing. During slagging period, FeS in copper matte is oxidized to FeO, which reacts with silica flux forming slag. When the iron content in matte is less than 1%, copper begins to oxidize and reduce to form blister copper (Kucharski, Sak, Madej, Wędrychowicz, & Mróz, 2013).

Jan 1, 2019

By L. W. F. Mackenzie

The influence of rolling temperature and annealing on the recrystallization and texture of magnesium AZ31 has been investigated. 100x125x6 mm AZ31 plate was cast in a permanent steel mould and then homogenized at 380°C. As-cast and homogenized microstructures were then characterized, and 35x30x6 mm specimens were machined from the homogenized material. Specimens were rolled up to 40% at temperatures between 25 and 350°C; selected specimens were subsequently annealed at 400°C. Following rolling, the microstructures were compared. The influence of rolling temperature on as-rolled texture has been demonstrated, and texture evolution has been evaluated following annealing. The recrystallization behavior has also been characterized. Optical microscopy, scanning electron microscopy and electron backscattered diffraction (EBSD) were used to characterize the microstructures of the alloys. X-ray texture analysis was used to investigate the texture in as-rolled and annealed specimens.

Jan 1, 2006

By J. B. C. Wu, B. McKee

"Mining along with subsequent processing of the minerals often presents conditions where a wear- and/or corrosion-resistant alloy is needed to minimize downtime and maximize efficiency. This paper is intended to give an overview of the alloys that are currently being used, as well as those developed in recent years that could be used in the mining industry. Emphasis will be put on the iron-, nickel-,cobalt-based alloys and composites containing a variety of carbides. The characteristics, properties, product forms, and methods of application are presented. In addition, examples of the actual use of these wear-resistant materials are illustrated.IntroductionPreventing wear and corrosion is important in any industrial operations. In the mining industry, the process equipment typically suffers many different types of material degradation. Abrasion, impact, erosion, metal-to-metal wear and corrosion are typically encountered. Each situation requires different material characteristics to retard the degradation process. Therefore, it is essential to understand the characteristics of the materials and the effects of the alloying elements.There are four common classes of metallic materials for resisting wear and corrosion; namely, iron-based alloys, nickel-based alloys, cobalt-based alloys, and carbide-containing composites. Each class of material has its own characteristics. Depending on the chemical composition, the materials within each class can be vastly different in properties. In recent years, there have been materials developed in each of the four classes using the knowledge of the metallurgical principles and the effects of the alloying elements on the material degradation process.To use a wear-resistant alloy, it is also necessary to understand the available product forms and their application methods. Weld overlaying is a traditional way of using these alloys (Wu and Redman, 1994). In recent years, thermal spray is becoming popular. For applications where over-laying and spraying are impractical, solid components can be made by a variety of casting and powder metallurgy techniques. They can also be fabricated from the wrought products.To select a proper material for an application, it is important to understand not only the characteristics of the wear-resistant materials but also the degradation process. Due to the complexity of the processing environments, past experience is also helpful in making the decision on the material selection."

Jan 1, 1997

By P. E. Cavanagh

Abstract Many investigators have been interested in developing some non-destructive method for detecting or determining the changes in physical properties in steel occurring during endurance tests or normal service life of a part which fails in fatigue. This paper presents a broad discussion of some of this work and the possibilities of developing useful test procedures based on some of the information obtained in the past. Changes in magnetic properties, electrical resistance, damping capacity, X-ray diffraction patterns, and remaining fatigue life at load different from service load have all been investigated as possible means for following the sequence of events during fatigue failure. In some special instances, tests such as these may be used to predict fatigue failure. As an in stance of practical application of the continuous determination of changes in magnetic properties during fatigue, a brief account is given of work done in non-destructive inspection of mine hoist-rope. As a result of extensive experiments and field crisis, it has been found possible to detect the beginnings of failure in a wire rope in service. The test method used will detect plastic deformation in a wire rope, no matter what its cause. There is no possibility of determining the remaining useful life of a rope by calibrating changes in magnetic properties in terms of remaining fatigue life. A change in magnetic properties at a point in a rope may indicate a decrease or increase in fatigue life, depending on the overload history of the rope. A continuing change in magnetic properties ac a point, however, does reliably indicate a developing weak point which will eventually lead to failure. The important point about any change in magnetic properties is not the magnitude of the change, but whether or not it continues.

Jan 1, 1947

By Donald S. Cameron

By dispersing gold in high surface area form supported on metal oxides, its inert character can be transformed to make economical, effective catalysts. Gold has already been demonstrated in a number of fuel cell applications such as gas phase catalysts, electro-catalysts, and electrical connectors. In this paper, the various types of fuel cell systems are reviewed, and several opportunities for gold identified. Low temperature fuel cells, including alkaline and solid polymer electrolyte types rely on high surface area platinum group metal catalysts which are highly susceptible to poisoning by low concentrations of carbon monoxide in the fuel supply. Hydrogen is frequently obtained by steam reforming hydrocarbons, followed by the water gas shift (WGS) reaction. A promising initial use for supported gold catalysts is in catalysing this WGS reaction. Research has shown that gold supported on iron oxide (Au/a-Fe2O3 ) WGS catalysts are more active than the current commercial copper oxide / zinc oxide catalysts, and effective at temperatures as low as 120oC. Products from reformer/ water gas shift reactors can be further purified by removing traces of carbon monoxide. If a small proportion of oxygen is introduced into the fuel gas stream, carbon monoxide can be preferentially oxidized to carbon dioxide even in the presence of hydrogen. Gold nanoparticle catalysts on iron oxide support (Au/a-Fe2O3 ) have exhibited higher activity than commercially available platinum on alumina (Pt/?- Al2O3 ) preferential oxidation catalysts. The low temperature of this reaction may make it feasible to incorporate these catalysts within the fuel cell itself. Proton exchange fuel cells provide several possible applications for catalytically active gold and its alloys. Carbon supported platinum group metals would benefit greatly from improved electrical conductivity if gold replaced some or all of the carbon support material. As electrode current densities are raised, electrical resistance constitutes an increasing proportion of voltage losses within the fuel cell. Dramatic reductions in cell stack voltage losses have already been demonstrated by reducing inter-cell contact resistance using gold plating. The low temperature oxidation properties of gold catalysts have been investigated in controlling gaseous emissions from direct methanol fuel cells, and gold also provides essential catalysis in building direct borohydride oxidation fuel cells. The prospect of a range of other applications for gold in fuel cells to contribute useful improvements in corrosion resistance and conductivity is assessed. Globally, fuel cells have been developed for a wide range of applications including stationary generators, cars and buses, industrial vehicles and small portable power supplies, each of which represents a substantial market. Hence there are likely to be many and varied opportunities for gold catalysts to contribute to the performance and economics of the systems being commercialized.

Oct 1, 2003

By E. J. Marcotte

"BRIEF DESCRIPTION OF GRINDING CIRCUITCrushed ore at -5/ 16 in. is delivered by a conveyor system from the crushing plant to two 1250 ton fine ore bins. The ore is transferred from each bin by a 30 in. feeder conveyor belt, operated by a Link Belt P.I. V. (variable speed) drive, to a 24 in. conveyor that feeds the 8 x 10 Allis Chalmers rod mill.The rod mill discharges to a common mill discharge pump box. Three 6 x 6 SRL pumps are employed to pump the combined mill discharge pulp to a common distributor box which distributes the feed to two of the three Kreb D lSB cyclones in each of the two banks at a hydraulic pressure of 6 psi.The cyclone overflow at a specific gravity of 1. 25 (i.e. 32% solids) is transferred by gravity to two revolving chip screens for wood chip removal and from there to a pump box. Two 5 x 5 SRL pumps feed the pulp to the thickeners. The underflow from the cyclones is fed to two 8 x 8 Allis Chalmers ball mills which discharge to the common mill discharge pump box. Thus, a closed circuit is formed between the ball mills and their respective bank of cyclones. The circulating load as most recently calculated is 262%."

Jan 1, 1966

By A. A. Nourbakhsha

During the last few years, low cement castable refractories found more application in industry, because of good low and high temperature mechanical properties.In the case of alumina based castables ,usually fume silica or reactive alumina are used as superfines in the matrix to form mullite at high temperature which depends to source of alumina . Mullite network formation improves the hot mechanical properties and thermal shock resistance of bodies. The mullitisation of andalusite (so called primary mullite) also produces a certain amount of rich silica glass, part of it being expelled out of the grain. This phenomenon restrict the application of andalusite low cement castable in pig iron ladle. In this research, firstly 8 pig iron ladles from ESC(esfahan Steel company) with different conditions selected and monitored during usage to determine of main factors affecting on corrosion of refractories. Results showed that tap to tap time and undischarged pig iron are the main ones.Therefore monolithic refractories such as castables which increase thermal shock resistance could be substituted. Regarding to ternary phase diagram of Al2O3-SiO2-CaO ,fumed silica was selected as fine particle.After optimization of particle size distribution by using of modified andreasen equation and rehological properties ,different mixture were composed with andalusite ,fume silica, reactive alumina,secar 71 ,SiC and kyanite.All aggregates system components were mixed dry for 1 min in hobart mixer .After water addition wet mixing was continued until getting flowing about 4 min.The ready mixes were poured in the moulds of of 25mm X 25mm X 140mm with vibrations .After demoulding the samples were cured for 24 hrs and dried at 110OC/18hrsand then fired at 1100-1500OC. Physical ,mechanical ,phase analysis(XRD) and microstructure studies (SEM)were carried out according to ASTM standards. Results showed that by addition of kyanite ,more mullite phase formed through the matrix but,because of expansion occured during this phase transformoration, some cracks formed and mechanical properties decreased.By SiC addition the silica film on the surface of SiC lead to improvement of mechanical properties at high temperature

Oct 1, 2011

By G. E. Wood

THE INSTABILITY of copper prices and their low levels since late 1974 are of great concern to both producers and, to a lesser degree, consumers of copper. The price levels portrayed by the "neutral long-term" price trend are assumed to have been enough to encourage sufficient investment to provide adequate world production capacity and yet not so high as to encourage development of excessive over capacity. The identification of the present level of this trend has taken on special importance for governments and for corporations active in the world copper industry. One approach to the possible determination of such a price is through the use of moving averages. In this way, the effects of relatively short-term price movements can be dampened, as can those related to business cycles. From such averaged price data, long-term trends can be sought over a selected time period. The choice of the past time period for which a price trend is sought may have a major effect on the result'. For example, in the period 1885-1973, the long-term price trend for copper in constant dollars showed a decline, whereas in the period 1919-1973 it was rising. For the purposes of discussion, an appropriate choice of period might be a relatively short and recent one so that the majority of the present cost factors would be present throughout. It should also be long enough to cover a number of full business cycles.

Jan 1, 1977

By A. Probst, N. Moores, J. A. Finch

"In 1994 McGill and INCO (Sudbury operation) initiated transfer of technology originally developed to detect level in flotation columns to thickeners. A conductivity probe was installed in a concentrate thickener to monitor the mud-line and solids load. The probe consisted in a vertical tube with 32 equally-spaced electrode rings connected in pairs to give 31 conductivity cells. Conductivity was measured as a function of depth (so-called conductivity profile) from which the mud line and % solids could be inferred. The probe was installed in October 1994 and has been successfully detecting profiles since then. This communication includes a description of incidents and experiences during this technology transfer process including: probe installation and start-up; software modifications to accommodate operating conditions and operators' needs; calibration procedures to adjust to changes in performance as a consequence of long term use; and preliminary observations on the last stage, still in progress, signal interpretation and use to facilitate operation, particularly by providing early reaction to upstream disturbances.IntroductionThickening is one of the basic unit operations in mineral processing and hydrometallurgy used to separate suspended solid particles from a solid-liquid dispersion by gravity settling. As the dispersion enters the thickener, the solids settle and clarified water overflows the top. A thickener, which may be continuous or batch, is basically a large vertical cylindrical tank provided with devices to feed the dispersion and to remove the settled solids. The tank provides residence time for the particles to settle. The dispersion enters the thickener through the feedwell whose function is to dissipate the momentum of the feed stream and to create relatively quiescent conditions around the entering point. Rotating rake arms move the settled solids towards the discharge point located at the bottom centre of the tank.There are normally three distinct zones in a thickener: a top layer of clear water, a middle layer called a sedimenting zone in which particles are settling, and a bottom layer called a compression zone in which particles are pressed together as a consequence of the weight of accumulated particles. Proper operation of a thickener requires two simultaneous conditions: no solids in the water overflowing the top and the target solids content in the underflow pulp. To achieve these conditions is difficult because sensors for detecting the sediment line (interface between clear water and sedimenting zone) and the solids content in the compression zone are not commercially available."

Jan 1, 1998

By W. F. James

"The property of Siscoe Gold Mines, Limited, comprises about 1,600 acres, including Siscoe island and adjacent claims under water in Montigny lake, in Dubuisson and Vassan townships, Quebec.For many years the property was reached by way of Harricana river and its chain of lakes from Amos, Quebec, about 45 miles distant. In later years a highway has been built from Noranda east through Val d'Or, about 5 miles distant.Gold was discovered on one of the claims on the north shore of Montigny lake as early as 1911, but these gold discoveries have never been economically important. Several years later gold was discovered on Siscoe island and considerable surface work was carried out. Still later, iscoe Gold Mines, Limited, was formed and carried out further work, some of it through shallow shafts. In 1928, larger scale operations were undertaken and a 100-ton mill was constructed. In the years following, production· was on a larger scale with lower grade, until finally a milling rate of over 1,000 tons a day was attained. Approximately 1,500,000 tons were treated between the end of 1940 and mid-year 1945. At present the milling rate is down to about 200 tons a day and work is confined chiefly to some of the less important veins that have been recently developed.The following is a summary of production up to December 31st, 1946:"

Jan 1, 1954

By A. F. Beck

Abstract Canada has opened up a geological province in ?Western Canada which offers a new .stimulus to oil exploration geophysics. The problems of instrumental technique, interpretation, and logistics involved in the exploration of this new territory are presented in this paper and some of the efforts being undertaken to overcome them are discussed. The scope of this programme, its possible trend and extent, especially when viewed .against the background of the exploration effort in the United States, is touched upon. Introduction The science of earth physics was first applied to the search for oil on this continent some twenty-five years ago when torsion balance and refraction seismic methods were initiated in the Gulf Coast area of the United States. Since that time advances in the various branches of the science have been sporadic as new fields for their use opened up in the search for deep salt domes as well as less well-defined geological structures; in the application to well logging as part of the exploitation of petroleum; and in underwater surveys, aerial surveys, etc. In the present paper, attention has been concentrated only on the Western Canada plains area because of the recent remarkable growth of geophysics as an oil finding technique in this region. The other prospective oil areas of the West Coast and the Eastern Provinces of Canada are at present of minor importance, although they will undoubtedly receive increasing consideration in the future as accessibility to markets becomes a major factor and more improved geophysical and geological techniques are developed. A vast province in Canada, covering some 655,000 square miles of prospective oil territory (approximately one-half of the prospective oil area in the United States), has provided the new sphere of activity for geophysics (see Figures 1 and 2). Included in this area are immense inaccessible, uninhabited frozen regions which pose a new problem in logistics and operational techniques.

Jan 1, 1950

By O. Lashkari

Swirled Enthalpy Equilibration Device (SEED) is a new patented Slurry-on-Demand, SoD, processing route. The semi-solid slug preparation is carried out by off-center swirling of aluminum melt in a metallic mould. As part of the current research program on the semi¬solid processing of aluminum alloys, the morphological evolution of 356 aluminum foundry alloy microstructure is reported here. Semi-solid slugs were prepared using two different pouring temperatures of 645°C and 695°C respectively. Morphological evolution of the semi-solid microstructure was characterized using image analysis through measuring of primary a-Al particle size, number density, aspect ratio and sphericity. The possible relationships between microstructural features and process parameters were also investigated. The current report covers the effect of pouring temperature on the morphology of primary a-Al dendrites and attempts are made to explain the differences between the predicted percentage primary a-Al phase and those of the actual values in the as-cast slugs.

Jan 1, 2004

The successful application of color sorting machines has established sensor-based sorting in the mineral industry in recent years and is considered today as a significant innovation in processing technology. However, we are only at the beginning of (market) introduction. New sensor systems have been developed, which exploit material properties such as electrical conductivity, magnetization, molecular structure, thermal conductivity etc. This opens up new exciting pre-concentration and upgrading possibilities for many applications such as nickel, gold, copper and other ores as well as for industrial minerals, diamonds and other gem stones.

Oct 1, 2009

By D. S. Cronan, S. P. Varnavas

Abstract - Metalliferous precipitates from submarine hydrothermal discharges have been investigated at four inshore locations off Milos in the Hellenic Volcanic Arc. The fine fraction of the sediments shows considerable variability in the concentrations of elements frequently associated with hydrothermal activity. Manganese varies from 30 ppm to 2500 ppm, encompassing the entire range of values found off Santorini also in the Hellenic Arc. Iron occurs in lower concentrations than off Santorini and Yali, while other elements often associated with hydrothermal activity such as Pb, Zn, As, and Cu also show enrichments in sediments from the hydrothermal vent areas. Selective leaching studies have shown that most elements are variably distributed between the different phases of the sediments but with enriched Pb, Zn, and Mn mainly in easily soluble secondary phases. Hydrothermal inputs are strongest at Palaeochori Bay, less at Voudia Bay and lowest at the Airport Springs and Rivari. The weathering of sulfide and possibly other orebodies is also thought to contribute to some of the elements enriched, while background concentrations are largely supplied from detrital sources.

Jan 1, 1999

By F. Charette

The paper reviews the requirements of the instrumentation required to monitor mining excavations in a high stress environment, and the development plan to instrument the D-Bolt in such a fashion as to be able to follow the behaviour of the bolts in relationship to the ground movements and support performance. Recent field observations of D-Bolts under static and dynamic conditions are also presented. Also discussed is the assumed mechanical behaviour of the D-Bolt. D-Bolts are used in two (2) Canadian underground mines operating in high stress environments and tested in three (3) other operations.

Jun 1, 2012

By N. Moelans, I. Bellemans, K. Verbeken

In this work, we present a phase field model to simulate the facetted crystallization of Fe3O4 in a quaternary FeO-Fe2O3-Cu2O-SiO2 melt under different partial pressures of oxygen. An important focus in creating more realistic phase field models is the incorporation of the thermodynamic driving forces in multicomponent multiphase-field models by coupling to thermodynamic databases. The diffusion of FeO, Fe2O3 and Cu2O is considered. The ratio of FeO/Fe2O3 at the upper boundary is in equilibrium with the oxygen fugacity of the atmosphere, while conserving Fe. Two-dimensional simulations are performed with different varying oxygen fugacity in the atmosphere. For the considered composition range, the growth velocities of the spinel crystals increase with decreasing oxygen fugacity. INTRODUCTION Crystallization of silicate melts has its applications in geology, pyrometallurgy and glass making. In pyrometallurgy, the solidification of slags influences the freeze lining behaviour (Campforts et al., 2007) and the cooling of slag after tapping (Durinck, Jones, Blanpain, & Wollants, 2008). Modeling of silicate melt crystallization is frequently done on the macroscopic level, using thermodynamic equilibrium calculations to determine the fractions of all phases as a function of temperature. The Factsage software and database package (Bale et al., 2016, 2009, 2002) already proved its usefulness in pyrometallurgical applications, for example to model the phase mixture after solidification of a stainless steel slag (Durinck et al., 2008). Crystallization of phases typically results in complex morphologies on the mesoscale, e.g. dendrites or facetted growth. On this mesoscale, the phase field concept has proved to be a very powerful tool (Moelans, Blanpain, & Wollants, 2008) for modeling crystallizing microstructures, because it can treat arbitrarily complex interface shapes with minimal mathematical complexity. In contrast to macroscopic models, the diffusion profiles and crystallization kinetics can be described as well as the morphology of individual crystals. First, Kobayashi (Kobayashi, 1993) simulated a growing dendrite in a pure undercooled metallic liquid. Then, Warren and Boettinger (1995) simulated a dendrite in an isothermal system considering a binary alloy. The extension to multi-phase systems was done by Steinbach et al. (1996). This was further extended by Tiaden, Nestler, Diepers, and Steinbach (1998) to a framework with coupled diffusion and phase field equations in multi-component systems.

Jan 1, 2019

By Fidelis T. Suorineni

HydraboltTM is a Swellex-type dowel support element developed and manufactured by New Concept Mining in South Africa. Like Swellex, the HydraboltTM is a folded tube which can be inserted into a larger diameter hole without pushing. It is then activated by injection of high pressure water which inflates the folded tube to intimate contact with the walls of the borehole at a set pressure, normally 25 MPa. Unlike Swellex however, the set water pressure at the end of the inflation is maintained throughout the life of the dowel. An integral non-return valve makes this possible. The HydraboltTM is being investigated as a possible stress change measuring cell. This paper presents the results of closed form solutions, numerical modeling and laboratory test to date. Preliminary results indicate that the HydraboltTM can be used as a stress change monitoring cell in addition to its conventional role as a rock mass reinforcing element. If successful, the HydraboltTM will supplement microseismic monitoring systems in rockburst-prone ground conditions where they will give quantitative stress change data for both mine design model calibrations and means for proactive safety measures.

Oct 1, 2010

By Z. Sun

The hydrogen embrittlement and stress-corrosion cracking (SCC) behavior of an a -titanium alloy and its two kinds of welding samples have been investigated. The results show that this alloy has very low susceptibility to SCC, and the values of Kiscc for the alloy are 46.4 MPa ? m' 65.86 MPa ? mu2 in the direction of T-L and L-T, respectively. The scanning electron fractographs show transgranular and quasi-cleavage fracture. The hydrogen embrittlement results show that the notch sample of the alloy is not sensitive to hydrogen, but the electro-beam welding and diving-arc welding samples are sensitive.

Jan 1, 2005

"During the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material from a selection of various drilling products or a sample from a mining test. It can be also a sample from an existing plant in order to investigate process enhancement. This sample can represent several tonnes of material which are analysed and split for use in various tests.In the current case, a composite sample of gold ore is dedicated to a Gravity Recoverable Gold (GRG) test. The properties of interest are the head grade of gold, the size distribution of the material, and the gold assay per size class. The sample is mixed and a sub-sample is taken to measure the feed properties: the size distribution and the gold assay per size class. The remaining material of the sample is subject to the first stage of concentration using the laboratory Knelson concentrator. The concentrate is analysed in its entirety, while a sample of tailings is taken for the same analysis. The remaining part of tailings is subject to grinding to feed the second and third stages of concentration. Similar sampling is performed at each stage.The concentration performances are analysed in light of these measurements. But what is the accuracy of the measurements of the properties? Pierre Gy’s theory of sampling, associated with a heterogeneity model built using the GRG test results, will answer this question. The current paper presents, through a real example, the calculation of the errors of the measurements of size distributions and gold assays performed during the GRG test. The uncertainties of the concentration performances and liberation size estimate are then calculated and their impact on the results interpretation is analysed.INTRODUCTIONDuring the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material from a selection of various drilling products or a sample from a mining test. It can be also a sample from an existing plant in order to investigate process enhancement. This sample can represent several tonnes of material which are analysed and split for use in various tests. In order to take into account the ore variability in terms of gold deportment, it is recommended to perform variability studies (Dominy, Murphy, & Gray, 2011, Dominy, 2013) using samples representing various horizons or years of production. But for a given ore type, it can be necessary to perform many tests with different operating conditions (Brochot, 2012a). In that case, the variability of the samples is not due to the heterogeneity of distribution of the deposit, but only on the heterogeneity of constitution of the primary sample. The level of confidence associated with the estimated performance parameters is directly linked to the overall error (including sampling error) of the measurements performed during the tests."

Jan 1, 2016