Search Documents

By S. N. Rossovsky

"A new method for the hydrometalfurgical treatment of refractory gold arsenosulphide concentrates is presented. Themethod involves a combination of' finegrinding, intensive agitation, flotation, and cyanidation, and consists of leaching of -10u pyrite and arsenopyrite particles in alkaline solution under intensive agitation without the application of costly high-pressure and roasting techniques. Consistent extractions of gold, in excess of 96%, are achieved.IntroductionConventional methods of alkaline leaching of gold arsenosulphide concentrates in an autoclave» and under electrochemical oxidation( 2) require expensive equipment as well as high-cost energy and reagents. In other cases, processing of gold concentrates inelude: ultra-fme grinding, calcination at 200°C to 250°C with the addition of an oxidant (NH4NOJ followed by alkaline leaching of the resulting calcine with hydrogen peroxide, the latter being a complicated method yielding poor extractions of gold (89% to 90%). In this paper, a hydrometallurgical method is described for processing refractory gold arsenosulphide concentrates in which alkaline leaching is followed by cyanidation of the residue."

Jan 1, 1993

By T. Abu Leil

A new class of ternary Mg-Sn-Ca alloys is being developed to address the dual demands of corrosion and creep resistance at service temperatures. While tin has proven to enhance the corrosion resistance, calcium is expected to significantly increase their creep resistance of binary magnesium alloys. Their effects in ternary magnesium alloys are not yet known. The series of alloys studied has Sn and Ca in the ranges 3-6% and 1¬2%, respectively. The results indicate that these alloys have two-phase structures with CaMgSn phase dispersed in a matrix that is predominantly a solid solution of magnesium. The corrosion behavior of these alloys has been investigated by means of salt spray tests and potentio-dynamic measurements. Creep behavior of these alloys was measured at a temperature of 135 C under an applied compressive stress of 85 MPa. Scanning Electron Microscopy with Energy Dispersive X-ray facility and X-ray Diffraction techniques were used to characterize the microstructures. The results indicate the prospect of designing alloys that can provide optimum combinations of corrosion and creep resistance by adjusting the relative compositions of Sn and Ca in the system.

Jan 1, 2006

By Wojciech Naworyta

The development of the Gubin lignite deposit, located in western Poland is the first mining investment of this magnitude in 30 years. Gubin is the second largest prospective lignite deposit in Poland, with over one billion tonnes of indicated reserves, which would be sufficient for a 2700 MW power plant for almost 50 years. The paper presents select problems related to the mining development of Gubin deposit. Attention has been paid to changes in legal and formal requirements for mining investments that were introduced after the change of Polish social and economic system. The significance of spatial, environmental and social conditionings has been emphasized. Typical attributes of the mine planning process have also been presented. Those include the long time horizon of the investment, uncertainty of external conditions and resulting difficulties in the project?s economic evaluation. Focus has been placed on mutual connections between particular elements of the project and time dependence during the process of their development. Iterative characteristics of the design process have been proven, together with resulting necessity of frequent verification of previous assumptions. As a background for presenting selected problems related to future development of Gubin lignite deposit, the methods of design have been discussed ? the variants method, the empirical method and the method of consecutive approximations. The tools and the possibilities of their use for solving specific problems related to mine design of an open pit have been broadly discussed. The chapter in which the authors relate to the specific problems of Gubin deposit development constitutes the main part of the paper. It depicts the assumptions on which the annual production and the total extraction of lignite during life-of-mine period have been based. The process of mine designing has been discussed, taking into consideration environmental, geotechnical, spatial, social and mining conditions. The criteria for choosing the location of the opening cut and the external dump have been mentioned. In the summary, the present state of mine design progress has been presented, together with some problems that will need to be solved during the next stages of the deposit?s development.

Aug 1, 2013

By P. Wanjara, M. Xiao, M. Jahazi, C. Poon

Using a robotic 4kW Nd:YAG-laser system, Inconel 718 (1 mm sheet) was welded with and without filler wire to investigate the effect of processing parameters, including power input and welding speed, on the weld geometry, microstructure and mechanical properties. By means of both nondestructive testing and microscopic examination, the weld quality was studied to determine the nature of the welding defects (porosity, cracking and bead shape) over the processing range of 3-3.5 kW for the power input and 4.5-6 m-min-1 for the welding speed. Application of the design of experiment methodology permitted the examination of the relationship between the process parameters and mechanical properties, from which the optimized laser welding conditions could be determined for joining Inconel 718. In particular, the research results indicate that Nd:YAG-laser welding technology can achieve defects free, mechanically sound welds with narrow fusion and heat effected zones.

Jan 1, 2006

By H. E. Johnston

There are currently a number of options in terms of plant feed comminution tests: Bond work index tests, JK drop weight and SMC tests, SPI, low impact crusher work index tests, to name a few. However, information regarding specific energy requirements for regrind mills is often requested, which can be difficult or very expensive when only a small mass of concentrate is produced from bench-scale flotation tests. This research was aimed at developing a test methodology that would produce a similar result as an IsaMill Signature Plot but require less sample mass allowing for preliminary estimates of regrinding power at a lower cost. Initially, the laboratory test methodology was completed on a single sample in comparison to the IsaMill Signature Plot for that sample. Results indicated a very good correlation between the laboratory tests and the IsaMill Signature Plot for this sample, though some parameters did impact laboratory regrind mill efficiency. The developed methodology is subsequently being applied to a range of concentrates, investigating a range of material particle sizes and material types, in comparison to a full IsaMill Signature Plot on the same sample. This new test procedure has been called ‘The Eliason Test’.

Jan 1, 2014

Presentation Overview ?? Project Setting ? Project Context ? Challenges ?? Managing Commitments ?? Project Update ?? Maximizing Aboriginal Economic Participation in Resource Development PROJECT SETTING ?? Developed on the traditional lands of the Labrador Inuit, and the Labrador Innu ?? Courts have held that Aboriginal peoples in Canada possess special rights to traditional lands ?? Rights can include requiring resource developers to enter into Impacts and Benefits Agreements ?? Development agreement with Newfoundland and Labrador was required

May 1, 2004

By Larry Urbanoski

"This paper describes the application of a radioisotopic energy dispersive X-ray aY1alyser to complete on-stream analysis in a base metal concentrator.The major components of the system are outlined and some description of the application, operating experiences and benefits are provided.IntroductionThe ma1n intent of this paper is to describe the on-stream analysis system in operation at the Geco concentrator. X-ray analysis systems installed in Canadian concentrators to-date may be broadly classified as wavelength dispersive analysers whereas the installation described herein is an energy dispersive x-ray analysis system. Energy dispersive x-ray analysis techniques may utilize radioactive sources to provide primary x-rays for excitation of elements and separate the secondary x-rays on the basis of energy levels. In contrast wavelength dispersive analysers apply high voltage x-ray tubes to provide primary x-rays and utilize crystals to disperse and thereby separate x-rays generated by bombardment of the sample."

Jan 1, 1978

By B. McFadzean, I. Achaye, T. Chidzanira, J. Wiese

"Froth stability has an overriding effect on metallurgical recovery and grade for many ore types. Froth recoveries of less than 10% are common for low stability froths such as those in sparsely mineralized ores or in cells at the back end of flotation circuits. It is well known that, aside from chemical factors such as frothers and electrolytes, the mineral particles themselves have the dominant influence on froth stability. The particle properties of size and hydrophobicity are expected to have the greatest effects on froth stability. The aim of this study was to understand the effects of particle size on froth stability and to quantify these relationships.The study compared a synthetic ore of pyrite and quartz, with carefully controlled size ranges and hydrophobicity, with conventionally milled platinum-bearing UG2 ore and the bulk reverse flotation of hematite ore. A novel bench-scale continuous column flotation cell and continuous mechanical hybrid cell with large relative froth volumes, as well as a three-phase froth stability column were used to characterize the froths.It was found that froth stability could be related to the concentrate particle surface area by a Langmuir-type relationship. This is indicative that the mechanism by which particles stabilize the thin films in froths is similar to the mechanism by which surfactants lower surface tension. Different froth stabilities were found for different ores and this was thought to be the result of different particle sizes and distributions, which resulted in different packing densities in the thin films and Plateau borders. Interestingly, there was a clear relationship between the feed particle size and the froth stability even though froth stability was dependent on the concentrate particle surface area. It seems that the feed particle size is a good predictor of the surface area of particles in the concentrate. Concentrate particle size did not show a clear relationship with froth stability since it was already shown that it is both the size and the amount of the particles in the froth that contribute to the stability.INTRODUCTIONThe stability of the froth in froth flotation is important to the recovery and grade of the valuable mineral. Too stable a froth and the grade is reduced; not stable enough and the recovery may be compromised. Platinum-bearing ores with fragile, poorly mineralised froths are known to have froth recoveries that are routinely less than 10% (Crosbie et al, 2009). There are a number of chemical, physical and operating parameters that can affect froth stability, including reagent dosages, air flow rate, pulp density and particle properties. Arguably, the largest contribution to froth stability is from the particles that stabilise (or destabilise) the thin films in froths. Particle size, hydrophobicity and shape all affect froth stability to some extent."

Jan 1, 2016

By Qidong Xu

Abstract - The metavolcanic rocks of the Dahongshan area have been subjected to both widespread hydrothermal alteration from circulating seawater and to regional metamorphism, such that their mineralogic and chemical compositions have been changed significantly. Studies of immobile elements show that these rocks were originally tholeiitic basalts with geochemical characteristics of T-type MORB formed in a mid-ocean ridge environment. The accompanying Cu-Fe-rich VMS mineralization is in keeping with the original petrology and tectonic setting of these metavolcanic rocks. Regional alteration evident in K-Mg enrichment is related to sericitization and chloritization. Local alteration associated with Cu-Fe mineralization appears to have been accompanied by Si enrichment and Na depletion. P enrichment identifies metasomatism related to Cu-Fe reconcentration in the mineralized zone.

Jan 1, 1999

By Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the North American database.

May 1, 2006

By Miguel A. Cuba

Trends in the mean and/or variance are a longstanding challenge in mineral resource modeling. Geologic modeling and/or grade domaining are often employed to account for heterogeneities in mineral grades; however, this is only practical up to a certain point since the number of data available for reliable model construction can be severely reduced. In such cases, trends remain present in certain geologic/grade domains and directly impact the modeling methodology; the trend must either be handled explicitly or a suitable approach is adopted to implicitly account for it. This is highly dependent on understanding the source of the trend. We propose an approach that detects the source of non-stationarity, which is based on quantifying the impact of non-stationarity in the mean and the variance via the semivariogram. By expanding the methodof- moments approximation of the semivariogram, we decompose the experimental semivariogram is into three terms: 1) trend in mean component, 2) trend in variance component and 3) stationary component. We can then assess the source of trend by calculating the contribution of each component at every lag. Two cases are presented to illustrate this tool. Firstly, a synthetic reference model is simulated and different trend patterns are added; the influence of these patterns in the experimental semivariogram calculation are analyzed and discussed. Secondly, a real dataset is considered where the impact due to the presence of trends in the mean and variance are assessed. The results of this paper reveal the semivariogram to be a tremendously powerful tool in determining the source of the trend. This insight may be useful in the selection of a suitable modeling approach for resource estimation.

Oct 1, 2009

By M. F. Gallerneault, V. Fallah, A. Howells, W. M. T. Gallerneault

"The occurrence of recrystallization in cold-worked aluminum sheet during the brazing process leads to loss of strength, an inhomogeneous grain structure and reduced corrosion resistance. AlMgScZr alloys are known for their extraordinary recrystallization resistance due to the influence of Sc and Zr addition on their microstructure. Here, we investigate the effect of alloy composition (i.e. Mn, Mg, Sc, Zr content), cold-roll reduction and pre-aging treatment on the recrystallization behavior of cold-rolled sheets at brazing temperatures typically used during the manufacture of heat exchanger units. The analysis of recrystallization behavior is carried out through microstructural characterization and the results are compared with the behavior of a commercial, AA3xxx-based heat exchanger alloy.INTRODUCTION Control of recrystallization is of critical importance during brazing, which is a widely-used joining technique for aluminum alloys in aircraft structures (Heinz, 2000) and automotive heat exchangers (Miller, 2000; Marshall, 1993). Due to excessive local heat at brazing temperatures, the cold work texture of aluminum alloys in the cold-rolled sheets may undergo a local recrystallization process (Marshall, 1993). This leads to the formation of an inhomogeneous microstructure and thus anisotropic mechanical properties (Miller, 2000) and low corrosion resistance (Marshall, 1993) across the sheet. X800, a commonly-used Al-Mn alloy series for automotive heat exchangers applications, has been developed specifically for a higher strength as well as an enhanced corrosion resistance as opposed to the traditionally-used AA3003 alloy (Marshall, 1993). X800 alloys, however, exhibit a low recrystallization resistance at normal brazing temperatures, i.e. 590°C. In contrast, Al-Sc-Zr alloys have been shown to exhibit an extraordinary recrystallization resistance at such temperatures (Riddle, 2004) while also being corrosion resistant and possessing a high room-temperature strength (Fuller, 2002). This has been shown to be due to the formation of coherent, nanoscale Al3(ScZr) precipitates that effectively impede grain boundaries while also exhibiting very slow coarsening kinetics at high temperatures (Riddle, 2004; Jones, 2003; Ocenasek, 2001). In this study, we analyze the recrystallization behavior of X800 alloys under brazing conditions through introducing Sc and Zr into the system as well as varying the Mn and Mg content. The effect of processing route is also studied by introducing a pre-aging stabilization treatment as well as varying the cold-roll reduction prior to the final brazing anneal."

Jan 1, 2018

By O. Guyot, A. Broussaud, M. Revalor, G. Legrand, D. Kok, E. Roux

"The paper describes the advanced grinding control system implemented at Newmont Ahafo gold mine, Ghana in 2009 and 2010. It shows how the different components of the Advanced Process Control (APC) system cooperate for increasing plant performance.The SABC circuit processes hard rock from different pits mixed with a variable proportion of oxides. The control strategy is designed to address specific disturbances, including start/stops of pebble crushers, unavailability of oxides, changes in rock size distribution resulting from segregation in the stockpile, and changes in ore type and hardness.The system consists of an expert system per se with extensive use of fuzzy logic, supplemented by an online dynamic model of the process used as a soft sensor, a VisioRock™ rock size measurement system over SAG mill feed before addition of recycled pebbles, and an AudioMill™ system to analyze the SAG mill sound and detect impacts on liners. All these components are embedded in the same OCS© software platform, which, among other benefits, makes it easy to support the entire system remotely. The paper details the physical constraints and the variables that are manipulated. It describes the control strategy and the contribution of each component of the system. It also describes the project implementation and the performance of the system. In addition to a strong involvement and support of management, the very good acceptance of the operators has been facilitated by the remote access system that made it possible to immediately modify the system each time it was needed during the baby sitting phase.The system made it possible to increase gold production significantly through increases in tonnage and recovery thanks to a better control of the grind size through a stabilization of the secondary ball milling circuit and an improvement of the operating conditions of the classifying cyclones."

Jan 1, 2012

By John Eggert, Paul Benford

"Since 1982, Placer Dome Inc. -Dome Mine has steadily increased mill throughput. Tonnage has increased from a nominal design capacity of 3000 short tons per day, attained in 1985, to 4130 stpd by the end of 1992. Many minor and major circuit adjustments were tried to maximize tonnage.Having utilized most conventional means of increasing tonnage, further increases required a newer approach. This paper discusses the Dome experience in the development and implementation of an expert system.The Comdale/C system was chosen for a controlled trial. The criteria for acceptance were: increased tonnage had to be sufficient to pay for the system; the increase had to be visibly sustainable and the mill operators had to be willing to accept the system.The criteria for purchase were met during the trial and the system was purchased. The system continues to perform well. The tonnage throughput increase has been sustained while operator acceptance remains high.IntroductionPlacer Dome Inc. -Dome Mine is Canada's oldest operating gold mine. The mine was among the first established in the Porcupine camp in what is now Timmins, Ontario. The City of Timmins is located approximately 500 miles or 800 kilometres north of Toronto. Figure 1 shows a map of the province of Ontario and the mine location.In 1912, milling began at a rate of 350 short tons per day. With two minor exceptions, milling has been continuous since this time. The first of these shut downs was in 1918 during the first world war. The war created labour shortages which forced the mine to stop production for more than a year. The second was in 1930 when fire destroyed the mill."

Jan 1, 1994

By G. W. H. Norman

The surficial Archæan rocks of the southern gold belt of western Quebec are constricted near Kewagama lake by granite masses to the north and south. This divides the belt into natural eastern and western parts. This paper deals with the eastern part, extending from Malanie to Haig township. In this section the Keewatin-Timiskaming rocks have a length of about 70 miles and end abruptly against garnetiferous gneisses of the Grenville terrain. In the western half of the section where exploration has been under way since the early twenties, there are sixteen mines that are or have been in operation, and eleven prospective mines. In the eastern half where exploration has been carried on since the early thirties, six prospective gold mines are under development, one· of which, Louvicourt Goldfields, is at the initial production stage. Of the sixteen properties in the western half that are operating or have operated, all, except the Golden Manitou, which is a base metal mine, and the old Green Stabell from which there was a small production of copper, produce gold. Of the eleven prospective mines in the western half nine have gold. New Bidlamaque has gold and copper and one, East Sullivan, has copper-zinc ore. Since production began in 1927 gold, silver, zinc, copper, and lead having a total value of about $10,000,000 have been produced from the mines of the eastern section of the southern gold belt of western Quebec.

Jan 1, 1954

By H. J. Glass, J. G. L. Bekkers

"In order to determine the feasibility of a hydraulic ore hoisting installation, the optimal operating conditions were calculated for applying such a system at the Detour Lake Mine of Placer Dome Ltd. Next, a financial analysis was conducted in order to estimate the cost per tonne for hydraulic hoisting of the ore. Subsequently, the cost per tonne was compared with the hoisting costs associated with a new borehole hoist. Installing a hydraulic ore hoist at Detour Lake Mine was found to be feasible with considerably lower costs per tonne of ore. The applied research method appears to be very functional and can be used to do similar research for other mining operations. IntroductionThe principle of hydraulic ore hoisting is well known, yet hardly accepted in hard rock mining. Application of the system would result in a smaller diameter shaft requirement and a flexible, easily expandable system. However, underground ore size reduction might be necessary and practical experience with the system is limited. Following recent innovations in the field of pumping hardware, e.g. new GeHo and Siemag Transplan equipment, hydraulic ore hoisting should be seriously considered for certain mining operations. As a case study, a design was made for the development of the newly found QK-Zone at Placer Dome Ltd.’s Detour Lake Mine. Hydraulic ore hoisting has been compared with conventional skip hoisting by establishing the optimal operating conditions and pumping equipment requirements for similar capacities at a selected mining operation. Generally accepted equations for slurry transport were used to predict the variation of pressure and power requirements as a function of hourly production and pipeline diameter. These data are used to select suitable equipment and estimate cost figures in order to make a financial assessment."

Jan 1, 1998

By W. A. Kracht

The McGill Bubble Size Analyzer, with the original image-capturing device (digital video camera), has a proven record for measuring bubble size distributions that are relatively narrow, such as in mechanical cells with frother. However, some problems arise when dealing with bubble size distributions characterized by a bi-modal shape and wide range of sizes such as found in some flotation columns. To measure wide bubble size distributions it is necessary to increase both the resolution to image the small bubbles and the viewing area to include the large bubbles. This can be done using a digital still camera: digital still cameras can have higher resolution than the digital video cameras currently used and with the proper lens the viewing area may be increased without resolution loss. The digital still camera approach was used to measure bubble size distributions in flotation columns at different operations in Chile. A comparison with typical bubble size distributions generated with mechanical cells is presented.

Jan 1, 2007

By F. Parada

During copper smelting and converting processes, slag generated is pyrometallurgically cleaned and then disposed, containing around 1 % of this metal. However, important amount of molybdenum initially contained in concentrates also goes to the slag phase. Research on molybdenum recovery from water granulated slags using acid leaching at low temperatures was conducted to find an efficient way for molybdenum extraction with lower magnetite in the slag. However because of the high fayalite content high acid consumption was found. Molybdenum can be recovered from solution using ionic exchange resins, but high silica content interferes with extraction. Some studies addressed to minimize silica extraction as well as alternatives of selective silica precipitation in order to develop a technically feasible process.

Jan 1, 2007

By P. Patnaik, F. Cuneo, D. M. Wang

Microwave (MW) energy has been used widely for several decades for communications, food processing, wood drying, vulcanization of rubber and medical therapy. Recently, this technology was found to be capable of successfully sintering ceramic and metallic powder materials, with the advantages of reducing soaking times and sintering temperatures. Unlike conventional heating, MW radiation works through the absorption of the microwave energy by a material placed in an electromagnetic field within the microwave cavity. A far more efficient heating process is produced due to the unique ability of microwaves in selectively heating a pecific part of the material with desirable dielectrical properties. This exploratory research was initiated with the objective of locally sintering the thermal barrier coating of gas turbine components using MW radiation. This novel technique may allow repairing of the component without subjecting the entire piece to unnecessary elevated temperatures and reduction of process time and cost. Y ttria stabilized zirconia was used in this study and sintering was conducted using a multimodal 1.2 kW microwave facility. Three configurations of heating setup were experimented and the preliminary results will be discussed in this paper.

Jan 1, 2006

By Samantha A. Beeson, Colin Poole

"A selective flocculation-floe flotation technique is already in use in the Canadian potash industry for the removal of water-insoluble slimes, but the process is currently limited in its application and reagent consumption is high. The work described in this paper details investigations into the separation of sylvite and halite from water-insoluble slimes by selective flocculation utilising other commercially available polymers.Preliminary flocculation performance tests were undertaken on pure sylvite, halite and water-insoluble minerals to establish the importance of a number of experimental parameters. The data from these single mineral tests was then used to establish optimum parameters for the separation of sylvite and halite from a synthetic mixture similar in composition to a typical potash ore. Under optimum conditions, separation was achieved with high recoveries using dispersant and flocculant dosages significantly lower than those currently used in plant practice.IntroductionAlthough solar evaporation and solution mining are used in some operations, most potash is extracted by conventional underground techniques and is then processed by froth flotation, in order to separate the valuable sylvite (KCI) from halite (NaCl) and water-insoluble gangue minerals. Flotation is usually preceded by a desliming stage to remove water-insoluble fines, but this also results in high potash losses and affects process brine requirements. To overcome these problems, one plant operated by Cominco in Saskatchewan uses a selective flocculation -floe flotation process (Banks, 1979/1980), in which a polyacrylamide flocculant is added to produce floes of water-insoluble material with minimal incorporation of halides. A collector is then added to render the floes hydrophobic and suitable for removal by froth flotation.A number of workers have also investigated the use of selective flocculation in potash processing, but these too have been concerned with developments in the removal of water-insoluble slimes (Williams, 1960; Brogiotti et al, 1974; Chan et al, 1986; Thompson et al, 1979; etc.). This paper provides results of novel investigations into the selective flocculation of sylvite and halite from water-insoluble minerals and discusses the possible mechanisms involved."

Jan 1, 1995