Search Documents

By D. F. Machuca-Mory

The new algorithm for high-order simulation of ore deposit grades termed HOSIM is based on the concept of spatial cumulants. The algorithm is tested using data from Apensu, a structurally controlled gold deposit in Ghana. The required high-order spatial structures are obtained from a training image or analogue of the deposit. Using the available drillhole data and training image, HOSIM realizations are able to model well the grades and geometry of the large and well sampled mineralized structures. However, under-sampled small structures remain difficult to model. HOSIM offers a promising alternative for the spatial simulation of complex non-Gaussian orebody attributes of interest.

Jan 1, 2011

By J. Font

New approaches for the fire refining process of blister copper have been carried out at the Codelco Norte Smelter. These have been mainly focused on modification and improvement of the process configuration based in fluid-dynamic and metallurgical studies of the oxidation and impurity treatment stages. This paper presents the results of the laboratory simulations and industrial tests performed in the 250 t anode furnace, evaluating two different process configurations: ? Bottom Bath Agitation System in the vessel during the oxidation stage, ? Dual Flux Injection System during the impurity treatment stage. The results show the possibilities of effective removal of high content of sulfur from the melt during the oxidation stage by using the bottom bath agitation. The use of the dual injection system demonstrated the significant improvement in the removal efficiency of impurities. Cu2007

Jan 1, 2007

By V. K. Srivastava1

Coal mine fires burn about 20?21 million tons of coal per year throughout the world, which not only results in loss of valuable coal reserves, but also cause serious environmental hazards over large areas. The famous Jharia Coalfield of Dhanbad, India is no exception; here a coal mine fire originally reported nearly a century ago is still continuing unabated in vast areas of the coalfield. In this paper, an attempt has been made to analyse high resolution multispectral thermal images of ASTER for mapping and delineating surface and subsurface coal mine fire areas of this coalfield. From the generated temperature gradient map, as well as from the surface temperature anomaly map, it has been possible to differentiate shallow and deep coal mine fire regions and other erroneous cultural features. It is observed that the coal fires are distributed mostly in the eastern part of the area, which has branched into two major coal fire zones: one along Lodna- Tisra-Bhulanbarari-Kujama-Jealgora Jharia and the other along the Kusunda-Kendudih area. The western fire zone is restricted in Dumra-Nadkhurkee-Jayramdih area. From ASTER thermal infrared data from 2006, the total affected area is estimated to be about 7 km2, of which the deep subsurface coal mine fire area is around 3 km2 and the shallow surface coal mine fire area is around 4 km2, as compared to 18 km2 coal mine fire area estimated in 1987 using Landsat TM thermal band data. In other words, the fireaffected region has decreased by about 50 % during the last 18 years. However, such decrease in coal fire area is seen in the central portion only, and has in fact increased in the south eastern parts of the Jharia coalfield. Study of Differential Interferometery images, generated from Earth Resources Satellite (ERS) synthetic aperture radar (SAR) tandem data has shown that the active coal mine fires are in general associated with low topography/subsidence areas.

Aug 1, 2013

By A. W. Chan

"An interactive computer simulation model of conveyor systems used in oil sands mining has been developed to aid in the selection of mining equipment and the evaluation of operating policies. The materials handling links between supply points, such as bucket-wheel excavators and draglines, and demand points such as bins and extraction plants are modelled in such a way that the conveyor model can be interfaced with any combination of these equipment submodels. Detailed calculations of the power demand of each conveyor section based on operating characteristics and conveyor design parameters are included to permit the close monitoring of energy requirements. Various interactive features are incorporated so that an operator can not only monitor, but also control, the mining operations in the model and experiment with different operating strategies.IntroductionThe interactive simulation model of conveyor systems described in this paper is one of a number of detailed computer models being jointly developed by the National Research Council and Canstar Oil Sands Ltd. on the mining equipment and operations used in oil sands mining. Reference I presents an overview of this whole series of models, their interrelationships and the underlying motivation for their development.A network of conveyors constitutes one of the practical ways for transporting mined material in an oil sands plant. The materials handling links between supply points, such as bucket-wheel excavators, bucket-wheel reclaimers and bins, and demand points such as dumps, bins and extraction plants can be represented by a series of interconnected conveyor sections. For example, the fluctuations of the feed rate at the bucket-wheel excavator, the flow of ore material through the conveyor network and the arrival of this material at the extraction plant can be simulated."

Jan 1, 1982

By Sean Dessureault

Technological Revolution ?Information age ? brought about by: ?Low-cost processing, storage, information sharing ?Shared & integrated data ? Increasingly more sensors & data sources From data collection to data use ??Data mining??analyzing the huge volumes of data ?Key example used in MBAs: ?Wal-mart, Google Explosion of data, trickle of information ?Paralysis of action Outline Trying to provoke- What drives innovation now? ?Challenges in mining Data Action Approach ?Examples from research & consulting upon request Conclusions ?Unaddressed challenges (Research Opportunities)

May 1, 2006

By Irving Wigden

The world is fast becoming information based. Mine companies migrate business infrastructures to be handled electronically. Suppliers move onto the worldwide web. In this ?e-world? successful suppliers will recognize they no longer trade in just equipment, but in knowledge. Companies can no longer just provide products and services, but instead must find ways to harness their knowledge to provide new value for customers. Mine customers will be attracted to suppliers that can help them streamline the process and use Information Technology to optimize operations, increase profit, reduce cost and enhance shareholder value. With the continued move to industry standard communications and software platforms, technology that formerly stood alone can now be integrated with other technologies. This creates more powerful systems that mine operators can use quickly, easily and cost effectively. These unified architectures improve productivity, provide higher asset optimization and allow more informed decision-making. As a leading supplier of process automation solutions for the industry, ABB provides a dynamic range of such control systems. These systems are designed for instrumentation controls, variable speed drives, electrical distribution, electrical equipment and related services for Mine Automation. Enhanced by ABB´s new family of integrated software solutions ? collectively known as Industrial IT ? ABB´s control and Scada systems place you in the best position to optimize your plant, process and enterprise operations. The paper discuss system integration and installation of High-Tec system in an underground mine. ABB has the ambition to be a System Integrator and co-operate with partners in different areas of technology. To day it is a problem to find one Supplier that can be responsible for the complete Automation System. The design of the system is also much depending of the design of the mine and also which caving procedure that is used in the current mine. Much of the work must be done in a feasibility study and during the design phase. If there is careful planning and consideration during these phases is vital in order to avoid costly changes during the commissioning phase The paper will also include a presentation of the benefit of using Automation in an Underground Mine, and how important the integration of the Human Being is to the Automation System. The most profit gained in mining industries are received when the mines can reduce internal and external disturbances in the production flow and speed. Must of the experience and discussed in this paper is from advanced technology, that has been developed in Scandinavian and adopted of LKAB in Kiruna. The author of this paper has been responsible för the Automation projects in the Kiruna Mine during 1994 - 1999. These projects include: Broadband communication of data, audio, compressed video in one data stream. Control System for Haulage -1045m Automation of Load Haulage and Dumping machines (LHD) Control of Production Drilling Riggs from a Central Control Room.

May 1, 2002

By Shantanu Patel, C. Derek Martin

"The objective of this work is to develop a practical numerical approach for applying the confining pressure to discrete element cylindrical triaxial tests. A layer of membrane particles with very low stiffness and extremely high contact bond strength was created around the lateral boundary of the cylindrical numerical specimen. To prevent the membrane particles from penetrating into the rock specimen on application of confining forces and to provide a smooth boundary surface, the space between the membrane and rock particles was filled using small-diameter packing particles. The results of this method were compared with those of rigid boundary method with confining pressure of 20MPa. The results obtained show that new approach gives both peak strength and post peak response that are in closer agreement with laboratory findings. BACKGROUNDThe discrete element method (DEM) has become the cornerstone for simulating both intact material and discrete fractures for low porosity strong rocks (ISRM Classes R3 to R6). Despite the advances in its application, simulating realistic behaviour of intact rock using the DEM remains a challenge. The bonded particle model was introduced as a potential solution for simulating the complex mineral grains in strong rock and other granular materials (Potyondy and Cundall, 2004; Utili and Nova, 2008; Salot et al., 2009). While some issues were resolved, a remaining challenge is the lack of the bonded particle model to simulate the brittle response commonly observed in strong rocks during the triaxial compressive test. Such behaviour is shown in Fig. 1 for Lac du Bonnet Granite at a confining pressure of 20MPa."

Jan 1, 2015

By Jonathan Peck, Jim Gray

"With the implementation of more advanced monitoring, control and locating systems in surface mines, there is an ever increasing need for their mine-wide integration toward achieving over-all optimization. AQUILA Mining Systems Ltd. is developing the basis for a comprehensive real-time monitoring, control and information system called the Total Mining System or TMS. This system is being designed to address both current and future needs of open pit mines toward improving productivity and minimizing costs, through better two-way information flow between each component in the operation. At a basic level, feedback from equipment and process monitoring will enable decision making to be based on quantitative, on-demand information, thus permitting proactive rather than reactive planning. Dynamic planning would be a valuable tool as market conditions fluctuate, equipment fleets age and variations in the grade, quality, geometry and hardness of the mined material all contribute to either changing production targets or levels of achievable performance. Such a capability could be implemented within the next two years.At a higher level, and within five years, autonomous operation and/or real-time supervisory control of mobile and stationary equipment in open pit mines will be achieved. A discussion is provided in regard to the development and implementation of an autonomous haultruck and blasthole drill, to demonstrate the need for such a system.This paper outlines a preliminary program for the design, development and implementation of this system, primarily in relation to high-level communications and its role in the future automation of open pit mobile equipment."

Jan 1, 1995

By M. A. EI Zeky, A. E. El-Nikbaily, M. A. Shahin

"Possible mechanisms of microsilica dust formation and factors affecting its quantity have been discussed. General mathematical models to predict the dust quantity based on electrical and coke consumptions, and flue gas temperature as functions of silicon recovery in the process and silicon content of the alloy have been established. It has also been shown that the flue gas temperature can be used as an additional process control parameter. Comments are made on the effect of the dust formation on the whole process economics and it is pointed out that the formed microsilica dust is a valuable by-product and not an industrial waste. INTRODUCTIONFerrosilicon is produced in electric arc furnaces with submerged electrodes. The charge mixture consist s mainly of quartzite, coke as the reducing agent and iron chips. The products are ferro silicon and carbon monoxide, various other volatile materials, water vapour and silicon monoxide gas. Carbon monoxide and silicon monoxide oxidize at the charge surface when mixed with air entering through the furnace hood openings. The off-gas contains a considerable amount of dust, which is mainly very fine particles of silica formed as a result of oxidation. The emission of dust containing gases to the atmosphere causes serious pollution problems to the environment. Therefore, the control of the formation of the dust, preventing it from escaping to the atmosphere, and dealing with this very fine dust collected from the flue gases represent important technological and economical parameters in the ferrosilicon production industry.This paper is concerned with the relations between the quantity of formed micro silica dust, as a function of both silicon recovery and silicon content in the alloy, and various other technological parameters; and their possible effects on the energy consumption and economics of the whole process."

Jan 1, 1989

By G. C. Weatherly, L Beitelman, M Gray, M. W. Bates, R Hadden

"A program of evaluation of in-mould electromagnetic stirring on the product of a straight-mould, billet continuous casting machine has been carried out. The effects on macrostructure, surface and internal quality, chemistry segregation and mechanical properties on carbon, low-alloy and resulphurized, free-machining steel billets and rolled bars are discussed. Operational aspects as a result of in-mould stirring are highlightedIntroductionA development program on electromagnetic stirring (EMS) in the mould of a continuous caster was started by Ferrco Engineering Limited in 1979, with the first experimental device being developed and installed at Lake Ontario Steel Company. As a result of these initial trials, new designs of in-mould EMS systems have been developed and are currently being used in continuous casters in North America and Europe. The rapid progress which has been made is in large measure due to the fruitful cooperation which has existed between the various parties, including Ferrco, the EMS equipment manufacturer, several operating plants and the University of Toronto.A brief review of some of the basic ' principles of electromagnetic stirring action on solidifying metal, and the landmarks of this process development, will explain the philosophy of this cooperation.From casting practice, it is well known that an equiaxed dendritic structure provides better' material properties than a columnar dendritic structure. Homogeneity of the equiaxed structure leads to better control of material properties, such as strength and ductility. Therefore, many efforts are being made to obtain this structure in continuous casting.The extent of the equiaxed zone is determined to a large degree by convective flow in the liquid. Fluid flow can fragment dendrites in the columnar zone, which then act as nuclei for grains in the equiaxed zone farther down the sump. This process is referred to as dendrite or grain multiplication."

Jan 1, 1982

By S. M. Bulatovic, D. M. Wyslouzil

"This paper presents the results of a study of the effect of flowsheet configurations on metallurgical results and describes a general method for developing and optimizing flowsheets used in the treatment of massive sulphide ores. The flowsheet configuration can have a significant effect on recovery and selectivity between valuable minerals and gangue minerals. Placing of intermediate products within the flowsheet, positioning of various pretreatment units, such as conditioners or regrinding mills, and the ability of the flowsheet to cope with wide swings in the feed grade and composition are the major parameters that determine the optimum flowsheet configuration. The complexity of the flowsheet is largely a function of the ore itself and of the number of final, marketable products that have to be recovered from the ore. INTRODUCTIONTechnological ExpansionThe trend of past decades has been towards larger equipment and a better understanding of the chemistry of the flotation process. Despite appreciable progress in these areas little attention was given to the study of the actual configuration of the flowsheet, although the arrangement of the flotation equipment significantly affects the overall performance of the circuit."

Jan 1, 1989

By Simon Pelletier, Jose Delgadillo, Dave Page, Pramod Kumar, Raj Rajamani, Dilek Alkac, Martin Fillion

"In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal’s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned.First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized."

Jan 1, 2012

"This paper discusses the use of risk assessment and risk management techniques within the Australian underground coal mining industry, within the context of geotechnical risk. The industry works within a pro-active, “enabling” legislative framework, where companies and management apply a range of risk assessment tools as part of their everyday management processes. Different geotechnical risk factors and approaches are reviewed, together with application examples – ranging from mine planning and design, operations, and accident investigations.A particularly powerful resource in each of the above stages of geotechnical management is the RISKGATE system. RISKGATE is an assembled “body of knowledge” structured under different topics across the Australian coal industry, of which three topic areas address rock mechanics issues for both the underground and surface mining sector. This paper will provide an overview of RISKGATE in the context of risk-based rock mechanics applications in underground coal mining."

Jan 1, 2015

By Don McColman

"Tires, although not always the largest single cost item in open-pit mining operations, will place in the top three, along with explosives and fuel. How this high-cost supply is controlled is dependent upon on an efficient tire program. The success of this program is, in turn, dependent upon the people who are directly associated with tires and their use, namely: the mine's tire personnel, the tire sales representatives and a technician for the rubber company. The technician will relay his observations and information received from the mine personnel back to the manufacturer with recommendations to overcome current problems .Haulage truck tire life and costs in a hard rock open-pit mine are governed and controlled by four important factors:I) Field control.2) Operating within manufacturer's guidelines.3) Different tire purchasing methods.4) Scrap piles.Field ControlPerhaps the most influential people involved in this program are those who live with the tire through every hour of its lifespan: the truck driver, the shovel operator, the dozer operator, the grader operator and the shift boss. Of these, the truck driver has the most control, in that he can drive over or around rock s as these situations arise. The loading area, the edge of the haul road and the dump account for most of the tire injuries.This is why shovel, dozer and grader operators must appreciate their influence on haulage tire life. Spillage cleanup must be ongoing and is not being done adequately if any of these operators are idle. The shift boss that drives by a rock on the road without removing it or calling for a cleanup has little recourse with the truck driver who runs over it-he has sanctioned the driver's actions by his own neglect."

Jan 1, 1986

By H. Ikeman

"The highly specialized communication systems used in the mining industry place exacting demands on equipment and transmission media. Safely and reliability of services are perhaps the two most important factors. Fibre optics is ideally suited 10 meet these stringent requirements. Aside from being an intrinsically safe, non-sparking and EMI/RFI immune medium , fibre optics offers greater reliability , higher quality of services and superior flexibility over conventional copper or radio-based communication systems.This paper wilt show how fibre optics can be applied in mining industry applications. Emerging trends and concepts will be presented to show how fibre-optic-based integrated service communication networks and local distribution systems can be implemented.IntroductionCommunication requirements in today's mine s are varied and extensive. The communication system must be rugged , safe and reliable, yet provide an ever increasing amount of high quality services. Presently, these systems are implemented using conventional copper cable. As mining method s and technology advance and the demand for better and more communication services increases, traditional systems quickly reach their limitations. It is under these circumstances that we turn to fibre optic communication systems.Fibre optics is a mature technology which is finding its way into more and more applications worldwide. A fibre optic communication system can provide a level of performance unattainable by conventional cable systems yet ca n be cost competitive. As is well known, fibre optics provides a noise-free, noise-immune, high -capacity communications channel. Glass fibre, being dielectric and non-sparking, is an intrinsically safe communications medium. Clearly, it is ideally suited to the harsh environment present in a mine.From a communication systems point-of-view, the topology of a deep mine is unique. The objective of the systems engineer is to implement a total communications capability throughout this wide spread area. Ideally all classes of services should be accessible throughout the network-an integrated network concept. Recent advances in communications technology combined with fibre optics make this realizable."

Jan 1, 1984

By S. K. Paul

"This paper briefly describes the underground crushing and conveying system at Sherritt Gordon Mines' Ruttan Mine. A series of three steel-cord belted conveyors, with a total length of 2J55 metres and a total vertical lift of 407 metres, convey the muck from the underground crushing station to the mill at the surface. The maximum size of the crushed rock is 6 in. All the conveyors are provided with numerous safety and fire suppression devices. IntroductionThe Ruttan Mine of Sherritt Gordon Mines Limited is located 20 km east of the town of Leaf Rapids, 760 km north of Winnipeg. The orebody is multilensed, with lens width varying from 6 to 45 m. Ore production started in 1973 with the opening of a 10,000-tpd open-pit mine. Initial development of the underground mine was started in 1972 with the driving of parallel conveyor and access declines at minus-2507o gradient to the I 220-m level, and then the access ramp was further extended to the 1160-m level. Exploration drifting was done on the 1280-m and 1160-m levels from the access ramp. The final development plan for the underground project was approved in January 1977, and full-scale development and constructionwere resumed.At present, Ruttan Mine is in a period of transition from open-pit to underground mining. Ore production is now coming from both operations. By mid-1980, open-pit production will cease and all production will come from the undergroundmine.The underground mining method at the Ruttan Mine is sublevel open stoping with delayed backfilling. The orebody is divided along strike into a series of 27-m-long stopes and 15-m pillars, both 60 m high."

Jan 1, 1980

By Tatyana Alexandrova

The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Technological aspects of processing precious metal ores are examined in two respects: enhancing gold recovery from double refractory ores; and using carbonaceous ores on a production scale. The dispersed carbonaceous matter (DCM) present in concentrates causes the adsorption of [Au(CN)2]- complex on their surface during cyanidation process. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The possibility of rare metals recovery, including rhenium, from black-shale rocks, has been examined. Comparative assessment of analytical methods of rare metals detecting has been carried out. It has been proved that neutron activation analysis is a promising technique. It has been shown that colloid-salt fraction (nanofraction) with particle size less than 1000 nm makes up to 3 wt% of black shale samples and is extracted by water under special conditions. The use of water instead of chemically active reagents provides insolubility of the mineral matrix and fully reflects the colloid-salt element of the samples. To sum up, the justification of the choice of technology for processing of carbon-bearing ores is based on examining the type of carbonaceous matter and its adsorption behavior. When the content of carbon of high degree of metamorphism is considerable, it is possible to recover platinum group elements and rare elements from this type of ores. The obtained results predetermine the general guidelines for creating new methods and techniques of processing carbonaceous material for integral development of solid minerals in the mining and oilfield areas of Russia.

Jan 1, 2016

By T. P. Kostek

"Historically, gear pumps and motors have been popular in the mining industry because of their competitive cost, simple yet rugged construction, ease of rebuild, and relative long life and insensitivity to contamination. However, with the ever increasing ""popularity"" of fire-resistant hydraulic fluids, both users and manufacturers of gear equipment must make special considerations to enable the equipment to continue giving satisfactory performance even with the water-containing fluids.The paper discusses 60-40 invert emulsions and waterglycolsIntroductionMuch information has been published on the specific characteristics of the various types of fire-resistant hydraulic fluids. Fluid manufacturers' literature and other publications have dealt with such specifics as fire resistivity, seal compatibility and wear rate characteristics. Gear pumps and motors have been, and will continue to be, applied successfully in hydraulic systems employing both the ""invert"" emulsions (60-40) and water-glycols as the hydraulic fluid.Because most external spur gear equipment has been designed to function with petroleum oil as the fluid medium, certain guidelines must be followed to ensure satisfactory service life. FluidsThere are a number of different types of fluids which fall in the category of"" fire-resistant"" , the most common'being phosphate esters, water-in-oil emulsions, oil-in-water emulsions and water-glycols. The two in most prevalent use today as hydraulic fluids are the water-in-oil emulsions and the water glycols"

Jan 1, 1980

By G. Tairova, J. Ioffe

Arsenic, selenium and mercury species are common contaminants in mining aqueous streams and present significant environmental and health problems. The objective of this project is to investigate methods to lower the concentrations of these elements in mining aqueous streams. A new composite media for removal of these elements of concern from mining effluents was developed. The results of bench scale and pilot plant experiments, using the media, indicated removal of arsenic, selenium, mercury and other elements of concern below detection limits.

Jan 1, 2014

By Paul E. Mather, Matthew J. M. Krane

Anode or fire refining is the final pyrometallurgical step in the production of copper anode. Part of this process purifies liquid copper by reducing its dissolved oxygen with a natural gas-steam mixture. Until now there have been no transient models of this process coupling the injected gas jet mass transport with its chemical reactions. A transient, 1D flow, chemical reaction model was made to estimate the time-dependent behavior of anode copper composition, soot formation, and the transient gas jet composition along its height. Model estimates were made for reduction rate, soot emission rate, and exergy loss and destruction distributions for two melt temperatures and a range of steam addition rates. It was found that increases to melt temperature and steam addition rate increased reduction rate and decreased soot emission, while having little effect on exergetic performance. Estimates for reduction histories were compared to industrial data. INTRODUCTION Anode/fire refining is the final pyrometallurgical step in the production of copper anodes; it is essential for removing dissolved gases which cause porosity in cast anodes. Despite its significance, the open literature appears devoid of any transient models of the entire process; furthermore, there are very little published process data with which to validate any models made. This dual dearth of modelling work and process data inhibits studies of the tradeoffs between process and performance changes, desirable for decreasing reduction time and soot formation as well as quantifying changes in the exergy losses and destructions of the process. This work introduces a reduced-order, transient model of reduction during fire refining, examines performance trends with operating conditions, and compares model estimates with industrial data. Overview of anode refining The purpose of anode refining is to produce liquid copper which can be cast with minimal gas porosity, which disrupts the downstream electrorefining process. Dissolved sulfur is removed first, then oxygen, by reactions with different injected gases. The removal of oxygen (the reduction step) is the subject of this proceeding and is effected by the bubbling of natural gas, typically mixed with steam, through the melt from tuyeres. A typical refining run reduces dissolved oxygen from 3000 ppm to 300 ppm in 2–3 hours (Schlesinger, King, Sole, & Davenport, 2011). The refined copper is then cast as anodes. Figure 1 shows a schematic of the furnace vessel.

Jan 1, 2019