Search Documents

By Li Qihou, Liu Zhihong, Liu Zhiyong, Yao Wei

Black copper sludge, which mainly contains copper, arsenic and a little antimony, bismuth, selenium, tellurium, is an important recyclable secondary resource. In this paper, selective removal of arsenic from black copper sludge by alkaline oxidative pressure leaching was studied. The influences of alkali concentration, leaching time, leaching temperature, oxygen pressure, liquid-solid ratio and other variables on the leaching rate of arsenic, copper and tellurium were investigated. The results were as follows: when the leaching process was conducted at initial alkali concentration of 1mol/L, liquid-solid ratio of 10, stirring rate of 500r/min, leaching temperature of 140°C for 5 h and oxygen pressure of 2.5MPa, the leaching rates of arsenic and tellurium were 85.43% and 59.7% respectively, and copper, antimony, bismuth were not leached. Hence, arsenic has been removed effectively from black copper sludge, while the valuable metals such as copper, antimony and bismuth remained in the residue that can be further recovered easily. INTRODUCTION Black copper sludge is a byproduct in the purification process of copper electrolyte. Arsenic, antimony and bismuth are major harmful impurities in copper electrolytic refining system. The accumulation of these impurities will cause adverse effects, such as the increase of electrolyte resistance and power consumption and deterioration of cathode copper quality (Wang, Liu, & Zhang, 2001). Hence, electrolyte purification is an essential part of the electrolysis process (Liang, Chen, & Guo, 2009). Electrolyte purification methods include electrowinning (Davenport, King, Schlesinger, & Biswas, 2002), solvent extraction (Navarro, Simpson, & Alguacil, 1999), ion exchange (Arroyo et al., 2017), coprecipitation (Wang et al., 2003, 2018; Xiao et al., 2007; Xiao, Cao, Mao, Shen, & Ren, 2014), activated carbon adsorption (Navarro & Alguacil, 2002), electrodialysis (Cifuentes et al., 2015), redox process (Zhou, Peng, Zheng, Ma, & Cui, 2011; Peng, Zheng, Zhou, & Chen, 2012; Zheng, Peng, Ke, & Chen, 2013), among which the electrowinning method is simple in operation and effective in impurities removal, making it the main process for current electrolyte purification. Some copper ions can react with harmful impurities to form complex black copper sludge by controlling the operation conditions of electrowinning process. Based on the estimated data provide by Davenport et al. (2002), an annual output of 400,000 tons cathode copper could produce 432-2168 tons of black copper sludge by electrowinning method. Black copper sludge contains 30~50% copper, 15~30% arsenic and a small amount of rare elements such as selenium and tellurium. Thus, recovery of valuable metals can bring huge economic interests. Moreover, arsenic in these sludges could cause significant environmental pollution. Therefore, effective removal of arsenic from these sludges is urgent and significant.

Jan 1, 2019

By M. Amsden

"Since the computer program is far from complete this must be only a brief progress report on the computerization of flotation metallurgy at the Ecstall concentrator at Timmins.Ecstall is currently treating about 10,000 tons per day of two different ore types. One is a low sulphide copper-zinc ore, the other is a high sulphide lead-zinc-silver ore. The concentrator is divided into three individual grinding and flotation circuits. In effect there are three mills under one roof. Normally there are two circuits on copper-zinc ore and oneone lead-zinc-silver ore. At this point in time one of the copper-zinc circuits is under computerized metallurgy control.The first step in this control is the use of an ARL on-stream x-ray analyzer, coupled with a Honeywell 21 computer which types out assays and recoveries for each individual circuit. Our approach to a computer program was to keep it simple. The program was written to coincide as closely as possible to what an operator would do in the performance of his duties based on the in-formation he was getting from the x-ray analyser read-out. Initially, computer control was put on just the copper circuit of the ""A"" Division, controlling the collector addition at three points in the circuit; primary, secondary, and scavengers. The control was based on recoveries and the grade of the copper concentrate. Targets like 95% recovery and 24% copper concentrate grades that it was felt the circuit could achieve were set to start with. It quickly became apparent that this alone was not enough because if on a certain ore the best recovery that could be made was only 94.9% the computer kept calling for more reagents until the circuit was completely out of control. On another ore it might have been quite possible to get 96% recovery but when the set point of 95% was reached the computer stopped trying for any more. To overcome this problem a very simple optimum seeking program was devised by one of the Ecstall staff and it has worked very satisfactorily since being put into use in July 1970.In the copper float only the two collectors R-208 and the xanthate R-317 are under computer control. The addition of frother and depressant is left to the operator. The flotation cells have automatic level controls which can be adjusted by the operator. pH is controlled automatically through a lime loop-sensor arrangement."

Jan 1, 1971

By C. B. Ndimande, C. Ntsele, M. Lisso, L. Arlow

"In the processing of UG2 platinum ore, stirred milling technologies are dominating regrind applications that require grinding the particles to P80s’ in the region of 45 µm. For this application stirred mills are 30–40% more energy efficient and require a smaller foot print compared to traditional tumbling mills. In this work a study was carried out using a batch pin mill and three scales of Stirred Media Detritors. A laboratory scale pin mill, a pilot scale Stirred Media Detritor with an installed power of 18.5 KW and two industrial scale Stirred Media Detritors in continuous operation, with an installed power of 355 KW and 1,100 KW were used. The industrial scale SMDs were in the secondary grinding section of a mill floatmill float (MF2) UG2 processing plants. The tests were focused on assessing the effect of feed rate and percent solids on power consumption and product fineness at lab scale, floatation response of the SMD product at pilot scale and on an industrial scale, the effect of feed rate on energy consumption and product fineness. The measurements obtained were feed flow rates, mill power and from the samples cut, particle size distribution of both feed and product. Specific energy was observed to increase with increasing percent solids over the 30wt% to 80wt% studied. Floatation response tests of the pilot scale SMD products show improvement in grade. Specific energy and reduction rations are observed to decrease with an increase in feed rate.INTRODUCTIONThe purpose of comminution in most mineral processing applications is to liberate the valuable minerals from gangue so that they can be recovered in subsequent separation stages. Most precious and base metal plants treat low grade fine-grained ores which require a higher degree of size reduction to yield the necessary degree of liberation (Partyka & Yan, 2007). Many authors have shown that the relationship between product size and grinding energy consumption is exponential, the finer the product from the comminution device, the higher the energy consumption (Gao & Weller 1993; Napier-Munn, Morell, Morrison & Kojovic, 1996; Jankovic, Valery & La Rosa, 2003). The suggested reason for this kind of relationship is that smaller particles have fewer flaws and higher strength than larger particles. Particles with fewer flaws and higher strength require higher energy for breakage to occur. One of the challenges most plants face is that of efficient energy utilisation in the liberation of the mineral from these complex ores. Conventional tumbling mills are not energy efficient in fine and ultra-fine grinding applications because some of the energy is spent on moving the charge and does not go directly into breakage. Stirred mills have been found to be about 30% to 40% more efficient and require a smaller foot print compared to traditional tumbling mills for regrind applications that require product size with P80s’ in the sub 45 µm regions (Radziszewski & Allen, 2013). Stirred mills are able to produce fine product because they can achieve a high number of stress events per unit time and volume compared to tumbling mills (Kwade, 1999a). To minimise energy usage without compromising product quality, the mining industry has adopted stirred milling technologies for fine and ultra-fine grinding (Radziszewski & Allen 2014; Kwade, 1999b). The south Africa platinum group metal (PGM) industry alone had over 40 stirred media mills installed by 2011 (Rule, 2011). Of that 40, 13 were in the ultra-fine grinding (UFG) application and the rest in main stream inert grinding (MIG)."

Jan 1, 2016

By J. Kronsteiner, E. Kabliman

"In the present work, we developed a Smart Process Control Toolkit (SProC) as a single simulation environment for the modelling of materials microstructure and its interaction with the local microchemistry during manufacturing of semi-finished products. This toolkit supports the data communication between sub-sequent processing steps such as casting, homogenization, pre-heating to deformation, etc. The thermo-kinetical simulation software MatCalc of MatCalc Engineering© GmbH was used for modelling of precipitation kinetics, such as formation of primary and secondary phases and their evolution. An import/export functionality of the precipitation distribution after each processing step was implemented to follow the parameter history. For the evolution of the local microstructure, a Mean Dislocation Density based Model (MD2M) was used. This model consists of two parts: (1) Flow Stress Model for calculation of the total strength during the deformation and (2) Static Recrystallization Model for account of the recrystallization and grain growth after the deformation. Validation was done by a comparison of experimental and simulated hot compression tests of a conventional AA2024 alloy.INTRODUCTION Optimization of a semi-finished products quality, elimination of typical production issues and cost savings are of a great demand for supply industries. However, it is currently not feasible to investigate the whole manufacturing process in detail at an industrial level. Concerning the processing parameters, one must understand the correlation mechanisms between macroscopic properties and microscopic material behavior. Numerical simulations, which could reproduce the real processing conditions on the one hand, and employ a physically based modelling on the other, are thus attracting a lot of attention and their power is no longer under the question. It is well known that e.g. the total strength of the material depends directly on distribution of precipitation particles and mean grain size. In order to follow their evolution during the manufacturing process beginning from casting to the final semi-finished product, and thus be able to control the process, one should use the techniques which would at the same time reproduce experimental processing conditions of real size objects (e.g. sheet, extrusions, etc.) and account for the evolution of a local microstructure and its interaction with the microchemistry. A commonly used approach is to implement a model which would describe the evolution of microstructure based on a dislocation density approach into a user defined material subroutine of some finite element solver. There is, however, also an influence of the manufacturing process by e.g. the evolution of a local microchemistry (formation, transformation and dissolution of the precipitation particles) on the microstructure and thus the macroscopic material behavior. Thus, a method is needed to follow the variable history through the simulation of the whole production chain."

Jan 1, 2018

By Derek H. C. Wilton

"The Cape Ray Fault Zone of southwestern Newfoundland contains two notable electrum/ base metal sulphide quartz vein lode occurrences hosted by two contrasting lithological units, viz. a graphite schist horizon and a granite. The two occurrences, although in proximity, are not in direct contact, but, based on geochronological, geochemical and isotopic evidence, they were apparently deposited from hydrothermal fluids generated as a vapour phase from the magmatic progenitor of the Windowglass Hill granite.This paper provides further evidence, from REE and background A u and Ag data, for the magmatic origin of the hydrothermal fluids. Wall rocks to the electrum-bearing quartz veins in both the schists and granite have experienced a LREE depletion probably due to leaching by Cl-bearing solutions. Gold and silver contents are typically low in all rock types but there is a slight elevation in gold concentrations in those units in contact with the Window glass Hill granite. The granite also has the relatively highest gold and silver contents of any unit in the region.IntroductionThis paper presents the evidence from rare earth element (REE) and gold/silver concentration data for the magmatic origin of hydrothermal fluids responsible for deposition of the Cape Ray electrum deposits of southwestern Newfoundland. The two deposits occur in the Cape Ray Fault Zone (Fig. I) within the Windsor Point Group and Window glass Hill granite. The larger occurrence is called the Main Shear Showing and consists of a deformed quartz vein horizon, which extends for - 6 km, within the late Devonian Windsor Point Group. This unit is an intermixed ignimbrite and mafic tuff sequence with associated schists (metasediments) and gabbros. The host rocks to the mineralized quartz veins are interleaved graphite, chlorite and sericite schists. Basal ignimbrites within the Windsor Point Group have been dated, by Rb/Sr isotopic methods, at 377 ±21 Ma (Wilton, 1983a). The basal ignimbrites also have enriched REE patterns, an elevated initial Sr ratio (0.709) and a peraluminous-siliceous nature which suggest they resulted from the partial melting of continental crust (Wilton, 1984)."

Jan 1, 1985

By J. W. M. Porritt, K. C. Cheng

Knowledge of radon emanation rates from uranium-bearing rocks is essential to the design of mine ventilation systems for uranium mines. Measurements of equilibrium ratio between radon and its daughters in mine air are important for a better control of mine radiation conditions. The concentrations of radon and daughters were monitored at cut-and-fill stopes in the Beaverlodge Mine of Eldorado Nuclear Ltd. during all phases of the mining cycle. The radon emanation rates of ore and rock samples were measured at the laboratory and the results were compared with in-situ emanation tests in an isolated ore drift. Samples of backfill solution, backfill drainage and ground seepage water were measured [or radon and analyzed for radium and uranium. The results showed that discharges of backfill solution and daily shift-end blasts were the two major sources for a rapid release of radon gas in the ventilation air. Other mining operations, such as drilling, mucking, etc., contributed little effect on radon release to the mining environment. Radon emanation rates of the Beaverlodge are samples ranged from 13 x 10-18 to 600 X 10-18 Ci/cm2/ sec and that of waste rock samples from 0.54 x 10-18 to 13.4 X 10-18 Ci/cm2/sec. The in-situ emanation rate of mine walls with ore-to-rock ratios of 1 to 7 was 60 x 10-18 Ci/cm2/sec. The average equilibrium ratio of radon and its daughters in stapes was 32.6%. Under a normal ventilation condition, the average background levels of radon concentration in cut-and-fill stopes ranged from 13 to 80 pCi/L. The discharges of backfill solution during backfill operations at 100 tons solids per hour released approximately 1.8 x 106 pCi/min of radon and elevated radon concentration in stapes 2 to 5 times above the background levels.

Jan 1, 1981

By M. K. Abel

"The Strathcona Mine is located in Levack Township on the North Range ofthe Sudbury Basin. The main orebody consists of pyrrhotite-pentlandite-chalcopyrite mineralization associated with an embayment of the footwall of the Sudbury Irruptive. A zone of massive chalcopyrite-cubanite-pentlandite mineralization occurs in a complex vein system in a series of mixed gneisses and breccias in the footwall. Vein widths vary from a few millimetres to 6 metres. In December 1979, this zone was estimated to contain 976,000 metric tonnes, with a grade of 9.31% Cu and 0.46% Ni. The vein system has a general strike of N 68°W at an angle of 60 degrees to the average strike of the footwall contact of the Irruptive. The dip of the vein system is 45 degrees sw. The strike and dip of individual veins in the system coincide with the directions that would result if a compressive stress had acted in a direction normal to the footwall of the Sudbury Irruptive, producing a conjugate set of fractures. The strike of the Irruptive at the Strathcona Mine is parallel to the long axis of the basin.IntroductionThe Strathcona Mine, owned and operated by Falconbridge Nickel Mines Limited, is located in Levack Township on the northwest rim of the Sudbury basin (Fig. I) . It is one of a group of nickel-copper sulphide ore deposits present along an 8.2-km section of the North Range of the Sudbury Irruptive. In the mines of the North Range, subunits of the Irruptive, going from hanging wall to footwall , include felsic norite, dark norite and dark norite breccia. The footwall complex at Strathcona includes the late granite breccia, which hosts a large proportion of the nickel-copper ores, and a compositionally variable group of brecciated and migmatized rocks, herein referred to as the feldspathic gneiss complex. It is within this latter group of rocks that the vein system of the Copper Zone occurs."

Jan 1, 1981

By A. P. Annan, C. Vaughan, J. L. Davis

"The increase in the price of gold in the last decade has led to a significant increase in placer gold exploration around the world. Placer deposits occur in depressions along ancient river and stream channels. In many instances these channels have been covered with materials from subsequent erosion or glacial activity. Use of high resolution geophysical techniques to map the bedrock and soil strata can improve the probability of finding the placer deposits. The buried bedrock surface is often the factor controlling deposition. Ground probing radar (GPR) and seismic sounding are complementary high resolution techniques which can be used to map bedrock topography and soil stratigraphy. Current radar instrumentation operates best in coarse grained soils. Penetration depths of up to 30 m have been attained, and stratigraphic horizons have been mapped with spatial resolutions of better than 0.5 m. Although its spatial resolution is considerably lower than radar, seismic refraction achieves superior penetration in electrically conductive environments such as clay and silt soils. The seismic refraction method thus proves to be complementary to the radar method. The seismic reflection technique is analogous to the radar method. Current seismic instrumentation and energy sources however, provide limited spatial resolution and do not permit the use of seismic reflection for reflecting horizons lying at depths of less than 20 m to 30 m.This paper discusses the use of both radar and seismic methods for placer exploration. The radar and seismic techniques, the field methods, equipment, and data displays are presented. Field examples illustrate the high resolution mapping capabilities of the techniques. The radar data agree very well with the borehole data, and in fact they sometimes detect subtle soil strata variations associated with changes of permeability that were not initially observed in the borehole logging. The radar method can give a continuous profile of water table and bedrock in sandy soils. Seismic soundings are necessary to differentiate between the bedrock and water table reflections observed by the radar."

Jan 1, 1987

By N. Hwang

There has been increasing interest in the use of robotic machines, and several prototype robotic machines have been developed to automate the grit-blasting process for the purpose of steel bridge maintenance. To utilize such a robotic grit-blast machine effectively, the first consideration is automating the determination of the rust surface area to blast, on the basis of standards of practice, in a rapid manner. This study aims to propose a method to rapidly and accurately determine the rust surface area on steel bridges to blast, with consideration for the standards of practice, from images acquired via a blasting machine. The first step is to perform a color space conversion to transform the input image from a red/green/blue (RGB) color space to a hue/saturation/intensity (HSI) color space. The next step is to detect the presence of rust, using pixel-level classification via the C4.5 decision tree algorithm. Then it is necessary to confirm the blasting area by verifying whether the rust detection result satisfies the specified criteria on the basis of standards of practice. The proposed method was validated on 39 test images with various characteristics with respect to the degree of rusting and rust distribution type. The experimental results showed that the average accuracy rate of rust area classification was about 97.63%, and the success rate of the final decision of blasting area determination was 100.00% for 39 test examples. The whole processing time took an average of only 0.86 seconds per image. The preliminary results demonstrated that the proposed method not only determined whether rust was present in an image and the amount of rust but also indicated whether blasting was necessary, and, if necessary, it rapidly specified the rust surface area that should be blasted on the basis of standards of practice. The proposed method could be successfully incorporated into a robotic grit-blast machine.

Aug 1, 2013

By Chri Langille, Dougal McCreath, Samantha Espley

"In 1993, trials of two innovative applications of liner support involving the replacement of bolts in the ground support system were undertaken at Inco mines. The first trial involved an evaluation of the effect of dynamic loading on mesh-reinforced boltless shotcrete in a sub-level cave mining area on 2400 level at Stobie Mine. The second trial involved an evaluation of the MIROC Mineguard spray-on liner as a replacement for bolts and screen support, or as a replacement for screen support alone, in a topsoil heading of a bulk, VRM (vertical retreat mining) stope on 3240 level at Lower Coleman Mine.In the Stobie Mine trial, an uppers retreat heading was supported using a two-pass system. First, shotcrete was applied 2 inches thick, followed by pinning of mesh screen to the back and walls. A second pass of another 2 inches of shotcrete was then performed. For recovery of the ore zone, a vertical slot was created using a Borepak blind boring machine. The uppers rings were blasted, one or two rings at a time, starting at the slot and retreating out of the heading. During blasting of the production rings, blast monitoring was used to record the ppvs (peak particle velocities). For a series of 5-ring blasts, the maximum ppvs were measured to be 0.4 m/s (16 in./s) with a maximum charge weight per delay of357 kg (800 Ib). Six 5-point convergence measurement stations were set up and after each blast the total rockmass convergence was measured using a tape extensometer. Although a maximum displacement of 100 mm (4 in.) was measured, the shotcrete still managed to provide some support junction. A support damage assessment was also done to try and relate blast vibration to effectiveness of the mesh reinforced shotcrete liner. This trial demonstrated the effect that blasting has, on a support system, and it also demonstrated the necessity of having the mesh reinforcement properly placed within the shotcrete."

Jan 1, 1995

By R. Chen, K. Xia

In deep mining activities, blasting induced compressive stress wave would be reflected as tensile wave at a free surface around the openings, which would facilitate the tensile failure of the deep rock since it is much weaker in tension than in compression. It is thus critical to understand the dynamic tensile failure of rocks subjected to static tension for deep rock engineering applications. A modified split Hopkinson pressure bar (SHPB) system is adopted to load Brazilian disc (BD) samples statically, and then exert dynamic load to the sample through stress wave generated by impact. The pulse shaper technique is used to generate a slowly rising stress wave and thus to facilitate the stress equilibrium of samples during each test. Five groups of Laurentian granite (with tensile strength of 12.8 MPa) BD samples under the pretension stress of 0 MPa, 2 MPa, 4 MPa, 8 MPa, and 10 MPa are tested under different loading rates. The result shows that the dynamic tensile strength of the rock decreases with the increase of pre-tension stress, which is easy to understand because pre-tension stress weakens the rock sample. It is also observed that under the same pre-tension stress, the dynamic tensile strength increases with the loading rate, revealing the so-called rate dependency that is common for engineering materials. Furthermore, it is found that the loading rate sensitivity of the rock increases with the increase of pre-tension stress. A qualitative explanation for this phenomenon is that more microcracks are generated and activated under higher pretension stress, resulting in a more viscous material. Based on the results, an empirical equation is proposed to fit the data and explain the dynamic tensile behaviour of rock under pre-tension stress. A physical model is used to simulate the dependency of the dynamic tensile strength of rock on the pre-tension stress and the loading rate, which is shown to be in good agreement with the experimental results.

Jan 1, 2015

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations for the smelting and refining of non-ferrous metals, and it is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate. It is also the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y zinc. Since then, production capacity has increased, and at present, it stands at 240,000 t/y zinc. In this paper, the leaching process and particularly the operation of the jarosite circuit is reviewed, specifying process improvements to treat high iron calcines.INTRODUCTIONTwenty years ago the Electrolytic Zinc Plant in Peñoles was treating high quality zinc concentrates with low concentrations of iron (~7.5 wt.%) and silica (1.8 wt.%). Nowadays the quality of zinc concentrates is poor with a typical iron content of around 11 wt.% and silica at 2.0 wt.%. This has created numerous processing problems in our roast-leach-purification- electrolysis sections. In order to meet customer requirements it is necessary to find processing solutions to assure the operational continuity of the plant. These processing solutions are the focal point of this paper.REVIEW OF THE LEACHING PROCESSThe purpose of the leaching process is to recover the metals, mainly zinc, through a series of extraction stages with sulphuric acid solutions, which progressively increases the zinc dissolution. After the series of acidification stages, the solution, which is rich in iron, is sent to the jarosite circuit to separate zinc from iron (Garcia & Valdez, 1996). The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper. Then this solution is sent to the tank house to feed the electrolytic cells."

Jan 1, 2016

"The Pierre Beauchemin Mine attained commercial production in January 1989, and went on to produce 23 968 ounces of gold for the year, 3% higher than forecast. Underground development was accelerated to prepare the way for the production of an estimated 40 000 ounces in 1989.IntroductionThe Pierre Beauchemin Mine is located nine miles west of the city of Rouyn-Noranda (Fig. I).As a result of the amalgamation with Sullivan Mines in October 1987, the mine is now entirely owned by Cambior Inc.The Eldrich deposit was discovered in 1953and began production in 1955, closing in 1962 following the decrease in gold prices and the simultaneous decrease in silica content in the ore, which was sold to the Noranda smelter for flux. A total of 717 000 tons grading 0.14 oz Au/t were produced during this period.From July 1984 to October 1987, an underground exploration program was carried out by Sullivan on the Eldrich mining concession and the nearby Flavel property. The first phase of the program included reinstallation of surface facilities and dewatering of the Eldrich Mine. Following the completion of the first phase, extensive exploration was carried out, including a major program of diamond drilling. It was then decided to deepen the shaft to a depth of 1800 ft to access a new zone called the No.5 Zone .Following the amalgamation with Sullivan in October 1987, Cambior assumed the role of operator for the project, and continued the shaft deepening work that had already been started. A feasibility study was completed in April 1988 and the Cambior board of directors approved a production decision for the Eldrich-Flavel project.The preproduction program extended from May to December 1988 and was aimed at preparing the stopes in the upper part of the mine and at developing the mine infrastructure at the bottom of the mine.The mine was officially opened in August 1988. Cambior renamed the project the Pierre Beauchemin Mine in recognition of Pierre Beauchemin's pioneer-work."

Jan 1, 1990

By W. A. Jones

"The Hollinger gold mine is in the Porcupine area, Cochrane district, in northern Ontario. The adjacent town of Timmins, which has a population of 25,856, lies 490 miles by railway north of the city of Toronto.The property was staked in the late summer of 1909. The original four claims were staked by Benjamin Hollinger, after whom the mine was named. Development commenced in the autumn of 1909 and mill construction in the winter of 1910. A catastrophic forest fire swept the district in 19ll, destroying the surface plant, so that the original 300-ton mill was not completed until June 1912. From that date up to December 31, 1945, 44,280,750 tons of ore have yielded 13,636,796 oz. gold and 2,613,354 oz. silver. The total value of the production has been $363,638,315.0REBODIES AND MINERALIZATIONThe orebodies consist of quartz veins, stringer lodes, and scockworks, with associated pyritized wall-rocks. The width of individual orebodies, as exposed by mining operations, ranges from 1 to 70 feet and averaged approximately 10 feet in 1942. The vein system forms a complex pattern in a favourable zone, which in places is 6,000 feet long and 4,000 feet wide. The deepest level being developed is 5,150 feet below the surface. Few veins are persistent for long distances, although some are continuous for more than 1,000 feet longitudinally and vertically.The host rocks consist of a closely folded series of Precambrian lava flows of Keewatin age. These are schistose and hydrothermally altered, but are believed to have originally been of intermediate to basic composition. The schistosity strikes N.70°E. and dips to the south at 75° to 80°. The structure of the formations is complex, but in the principal ore-bearing zone the general dip of the flows is to the south at a slightly flatter attitude than the schistosity."

Jan 1, 1954

By M. E. Stutt, R. H. Rehder

"The mining industry is taking advantage of the increased performance resulting from the use of variable speed A C drives for large motors. This technology provides increased efficiency under the variable speed and torque requirements of such drives as mine hoists, conveyors, and air moving equipment. The technology does introduce voltage spikes on the voltage wave form that stress the insulation system to a greater degree than would occur with a constant voltage source. These voltage spikes must be considered in the design of the insulation system used for these motors.BackgroundHistorically the insulation systems for large AC motors were designed to withstand with reasonable life the voltage stresses of a 60 Hz constant sinusoidal voltage. One of the design tests is a voltage endurance test that requires the application of a 60 Hz voltage from conductor to ground equal to four to five times normal and establishing a time to failure. These higher than normal voltages accelerate the normal aging process by causing extensive partial discharge activity (corona) within the insulation system and the time to failure is a relative indication of insulation life.In addition to the voltage endurance test at 60 Hz, the individual coils are subjected to a surge voltage test to establish the withstand capability of the turn to turn insulation under switching surge conditions. The surge voltage is a fast rise time, 0.2 microsecond to crest value, voltage spike that can be caused by a circuit breaker or contactor closing operation. These voltage spikes can have a crest value of greater than 3.5 times the normal line to ground crest voltage of the normal 60 Hz power supply. The standard withstand test value is thus 3.5 times normal line to ground voltage. Because the voltage surges or spikes occur mainly during start and stop switching conditions, voltage endurance under these conditions has not been a major factor in insulation system design."

Jan 1, 1995

By C. K. Baxter, A. Odeshi, M. Mohammadi, E. D. Cyr

"Metal additive manufacturing has been a revolutionary step in designing new complex shapes with faster and cleaner building capacity in comparison to subtractive manufacturing processes. The ability to print lightweight alloys such as aluminum has made metal 3D printing attractive to different industrial sector from aerospace to energy and bioengineering. Of particular interest in this study, are the mechanical and microstructural properties of AlSi10Mg-200°C alloys. In this project, samples were 3D-printed in horizontal direction using an EOS M290 machine by Direct Metal Laser Sintering (DMLS) technique. Uniaxial tensile tests and high strain-rate impact e tests were carried out to investigate the mechanical properties and to study the repeatability of the process. A constitutive model is developed to predict the results of the mechanical tests at varying strain rates to better understand the high strain-rate behaviour of these alloys. Using optical microscopy, features such as scan tracks and melt pools within the AlSi10Mg-200°C samples were observed, and the microstructure was observed to be homogenous. The previously listed tests were compared to the results obtained for similar cast alloy counterpart, i.e. A360.0.INTRODUCTION A relatively new way of manufacturing parts is on the increase as rapid prototyping becomes increasingly popular throughout the world. Additive manufacturing is a process which, given a 3D model, uses metallic material in powder form to build a part layer by layer until completion (Gu, Meiners, Wissenbach, & Poprawe, 2013). This way of rapid prototyping is very attractive in comparison to other possibilities because of its ability to accommodate complex design and geometries. Conventional manufacturing methods have limitations when it comes to complex geometries, but additive manufacturing allows for increased design flexibilities while maintaining a light and stable final product (Murr et al., 2012). It also allows for a reasonable cost, especially for small batch sizes that would otherwise be extremely expensive."

Jan 1, 2018

By Darryel Boucher, Thomas W. Leadbeater, Raymond Langlois, Joshua Sovechles, McGill University, Zhoutong Deng

"Spiral concentrators are used to upgrade ore based on the density difference between their component minerals. This simple flowing film gravity separator is of interest for the processing of large amounts of material, as found in the iron ore industry. Addition of wash water at different points on the trough of the spiral affects the grade and recovery of the valuable concentrate by affecting the flow of particles within the thin slurry film. This paper shows how radiolabelled hematite (-355+300 µm) and quartz (–1,180+1,000 µm) tracers were used to determine the particles’ behaviour within the slurry film with and without the addition of wash water. The results presented provide a detailed particle flow pattern around a wash water addition point and its effect on the trajectory and velocity of the particles. This information is of interest in building knowledge about spiral wash water injection parameters such as injection location, direction, flow rate and nozzle orifice type (affecting jet shape and velocity).INTRODUCTIONSpiral concentrators are density based separation devices. They are extensively used in the upgrading of iron ore, fine coal and minerals sands (sources of ilmenite, rutile, zircon and monazite) (Wills & Finch, 2016). A spiral unit is composed of a channel of specific profile formed as a helix of 3 to 7 turns around a central structural post. The feed pulp is composed of 15 to 45% solids with particle size from 75 µm to 3000 µm (Wills & Finch, 2016). Throughput of a single spiraling trough can be up to 8 ton per hour and multiple trough unit (up to four trough) can process up to 30 ton per hour for a footprint of around 0.7 m2 (Palmers & Vadeikis, 2010). They are low cost concentrators considering manufacturing of their trough via polymer reverse molding. The energy intensity of a spiral plan is notably small considering the throughput and is mostly related to pulp pumping and final concentrate dewatering."

Jan 1, 2016

By Adam Jordens

Along with gravity separation and froth flotation, magnetic separation is one of the most common techniques for separating minerals. Minerals are separated by a magnetic force that is dependent on a combination of the applied magnetic field, the magnetic field gradient and the magnetic properties of the minerals themselves. Minerals may be classified as diamagnetic, paramagnetic or ferromagnetic based on the way they interact in a magnetic field. The magnetic susceptibility of a material may be determined by using a vibrating sample magnetometer to determine the magnetic moment of the material in an applied magnetic field and then converting this measured moment into the material?s magnetic susceptibility. In the case of rare earth minerals, magnetic separation is commonly used to remove ferromagnetic iron-bearing gangue minerals and to concentrate paramagnetic valuable minerals such as monazite and xenotime. These magnetic separation steps are frequently preceded by a gravity separation step as many iron oxides and rare earth minerals have specific gravities that are much larger than those of typical gangue minerals. By varying the magnetic field intensity it may be possible to use magnetic separation to selectively separate the paramagnetic and ferromagnetic minerals that report to the concentrate after gravity separation. Test work on a Canadian rare earth ore has shown that a gravity concentration step using a Knelson concentrator was able to selectively concentrate heavy magnetic minerals as evidenced by increased recoveries, relative to the Knelson tailings and fresh feed, after processing through a wet variable intensity magnetic separator. Mass pull to the Knelson concentrate was 4.5 % and the magnetic recovery of this concentrate, at 0.94 T, was approximately 40 % higher than the magnetic recovery from the Knelson tailings (70 % versus 30 %). The products of the wet high intensity magnetic separation were also analysed using a vibrating sample magnetometer to determine the magnetic susceptibilities of the various concentrate and tailings products.

Aug 1, 2013

By R. J. McLeod

"Grinding at Giant Yellowknife is done in two stages. The first stage consists of two ball mills in closed circuit will: mechanical classifiers, the classifier overflow goes to flotation. The tailings from this flotation circuit are separated into slime and sand portions, the slimes go to an additional flotation circuit while the sand portion goes to the secondary grinding mills.Milltronic automatic sound control units were installed on each of the two primary ball mills and put into operation September 3, 1966. After about two months adjustments to the control units the operators were taken off the grinding circuit on November 1, 1966. The operators duties were taken over by the automatic control units while miscellaneous work was taken over by the helpers in the mill. The labour saving by the installation is approximately $2250.00 per month.After a short period of operation it was apparent there was a slight change in grind. The screen analysis of the primary classifier overflows for the period May to August 1966 averaged 62.23% minus 200 mesh while for the period September to December 1966 averaged 62.0% minus 200 mesh. This is a slight coarsening of the grind. The change in the primary grind has manifested itself also in the screen analysis of the final grind. Before automation the final grind was 80% minus 200 mesh, while after automation it was 7 5% minus 200 mesh. A change of grind was also noted in the flotation concentrates. Before automation the screen analysis of the concentrates was 35% plus 200 mesh and 50% minus 3 25 mesh. A ft er automation it was 35% plus 200 mesh and 47 .5% minus 325 mesh. In other words the grind got coarser or perhaps we should say there was less overgrinding. Another significant change took place in the assays of the slime and sand portion of the primary flotation tailings. It was usual under manual control for the slime portion to assay higher in gold than the sand portion. The reverse is now true."

Jan 1, 1967

By A. A. Nourbakhsha

The main application of refractories based on andalusite in ferrous metallurgy are in air heaters of blast furnaces, mobile mixers, and hot-metal transfer, pig iron ladle, steel-casting, and intermediate ladles. Three specific properties of andalusite are very interesting for the production of high-quality shaped and unshaped mullite refractories: being free of water, its crystal a remains stable without changing its density or volume after firing and therefore has no internal porosity .Graphite additives due to its great wetting ability play an important role in raising the property of refractory bodies. In order to improve properties of andalusite graphite bodies, oxidant agent for increasing in hot strength and oxidation resistance can not be avoided. In this research, firstly 8 pig iron ladles from ESC(esfahan Steel company) with different conditions selected and monitored during usage to determine of main factors affecting on corrosion of refractories. Results showed that tap to tap time, undischarged pig iron ,penetrated pig iron are the main ones.Literature studies showed that the graphite addition help to thermal shock resistance and liquid penetration(steel,pig iron) effect. In this research particle size distribution of aggregates containing andalusite and graphite determined by andreazen equation. Then different mixes with different percentage of graphite,Si, FeSi, SiC prepared by uniaxially pressing under 1500kgf/cm2 pressure by adding 4%wt novalak resin and 0.4%wt HMTA as hardner. Samples fired at 1100-1500oC under reduction atmosphere. According to specific standards density, porosity and CCS measured. Analytical tests such as XRD, SEM were carried out on sample selected from point of view of mechanical properties at different temperatures. Results showed that optimized amount of Si and Fe-Si for _-SiC formation in body is 4 and 6 %wt respectively at 1500OC. XRD and SEM analysis on sample with Fe-Si additives showed no destructive phase through the matrix, also SiC additives not only increase oxidation resistance but also no effect on thermo-mechanical properties.

Oct 1, 2011