Search Documents

By Pier-Olivier Devin, Daniel Hodouin, Maryam Sadeghi, COREM, Claude Bazin, François Lavoie

"Spiral concentrators are used for processing coal and heavy minerals such as it is the case for the concentration of iron oxide from light silica gangue. The concentration process for iron ore usually consists of a rougher bank of spirals followed by two stages of spiral cleaning. The process control applied to the concentration circuit aims at maintaining a target iron content of the final concentrate and is mainly conducted by adjusting the wash water addition and the position of the splitter gates at the discharge of the spiral. This paper describes the use of a simulator to study control strategies for a gravity concentration circuit using spirals.INTRODUCTION The Canadian iron ore mines are located in the Northern part of Quebec and in Labrador (Neal, 2000). These iron ores consist mainly of hematite with some ore bodies rich in magnetite and ilmenite. The processing of the coarse hematite iron ore consists of the extraction from an open pit mine, followed by the conventional crushing and autogeneous grinding of the ore to obtain a particle size smaller than 1.2 mm. The ground ore assaying 40% hematite (Fe2O3) with quartz (SiO2) as the main gangue is processed by spirals to produce an iron oxide concentrate assaying 90 to 95% hematite.Spirals separate the particles according to their specific gravity and size (Burt, 1984; Bazin et al., 2014). These environment friendly devices have been used for decades and are still used for the preparation of coal and for the concentration of heavy minerals such as iron oxide (Staff, 1977; Wills, 1992). However very little information is available concerning the control of gravity concentration circuits. This paper analyzes the control practice of a gravity concentration circuit using a simulator. The paper consists of 3 sections. The first section describes the operation of spirals and spiral concentration circuits. The second section briefly describes the simulator and shows some simulation results for a gravity concentration circuit. The third section shows the application of the simulator for the study of control strategies for a spiral concentration circuit."

Jan 1, 2016

Roasting of molybdenite concentrate is an important stage in the production of commercial molybdenum trioxide. The oxidation kinetic and mechanism of molybdenum sulfide concentrates from two plants were investigated at temperatures from 444 °C to 640°C. The rate of reaction was determined for thin layer samples in a muffle furnace at controlled temperatures, oxygen excess and removal of sulfur dioxide. For both concentrates the rate of reaction is fairly slow at temperatures below 500°C and remains fairly constant from 540 to 600 °C. It was observed that the concentrate from the first plant presents a tendency for sintering or glazing at temperatures above 620°C, whereas the same phenomena was observed at 20 or 30 °C higher temperature for the second concentrate. A kinetic model of two reactions, involving the formation of Mo02 as intermediate oxide for the production of Mo03 is proposed and activation energies of 23.0 and 20.8 kJ/mol for the first and second reaction were calculated for temperatures between 520 °C to 600 °C. These low values of activation energies indicate that the overall rate of oxidation is controlled by mass transfer, particularly in a porous layer of oxides. Therefore, the renewal of the surface by mixing and motion of the concentrate layer is of great importance. Sublimation of Mo03 becomes significant for temperatures above 650 °C.

Jan 1, 2007

By John Lamb

"The French Mine (formerly the Oregon) is 4 miles by road south of the Nickel Plate Mine. It lies on the steep eastern slope of the Similkameen River valley at elevation 4,000 feet, between Cahill and Winters Creeks.The property was discovered in .1901 and bought 4 years later by Messrs. French and Deardorf. It was developed in a modest way by the owners and by several companies until 1947, without success. The spectacular showings of bornite and chalcopyrite in the outcrop drew attention to its possibilities for copper rather than gold. Diamond drilling by the owners in 1947 yielded several high-grade gold intersections and created new interest. In 1949 the property was purchased by Kelowna Mines Hedley Limited. Exploration drilling and geological mapping outlined sufficient ore to commence production in 1950. Except for a few months each winter the operation has been continuous, and to the end of 1954 had produced almost 30,000 tons of high grade ore. The ore is crushed at the mine and hauled 8 miles by truck to the Company mill at Hedley, where it is treated together with the ore from Nickel Plate.Regional GeologyThe country rock consists of brown tuff, flows, limestone, and cherty formations belonging to the Nicola group (Rice 1947) of Triassic age. West of and just below the mine is a large mass of granodiorite which is part of the same body that underlies Nickel Plate Mountain. Bedding attitudes in the mine area are locally complicated, but dips are generally less than 45 degrees. To the south and below the mine the beds stand almost vertical, continuing downward with this attitude for 2,000 feet to Winters Creek. The main granodiorite contact is also steep, conforming to the sedimentary formations, whereas northward towards Nickel Plate it dips gently to the northwest, slightly flattter than the thick westerly dipping pile of sediments above it. The interpretation of this structure by Billingsley (1936) is that the French mine lies near the crest of the large northeasterly trending asymmetrical anticline which contains in its gently dipping western limb the Nickel Plate orebodies. The granodiorite body conforming roughly to this shape seems to occupy the core of the anticline. Sill-like prongs of granodiorite extend upward to the east from the main mass, outcropping over wide areas at the head of Winters Creek (Figure 1). There is a possibility that overthrusting from the west, similar to that on Nickel Plate Mountain, occurs not far below the French mine.An interesting feature of the granodiorite-sediment contact is that where it dips gently westward no alteration exists in the sediments, but where it has a steep front pronounced heat effects are indicated by the presence of a thousand-foot-wide zone of reddish garnet skarn."

Jan 1, 1949

By J. F. Dorion

This paper presents the results of on-going investigations on the performance of support systems in Québec underground mines. The focus of these investigations is on site observations complemented by laboratory investigations. Of particular interest is deducing the corrosion rate, at selected mine sites, as determined by the installation of monitoring coupons.

May 1, 2009

By A. E. Gran

"QIT -Fer et Titane Inc. currently produces and markets four main products: a titania slag named SORELSLAG for the white pigment production, a high purity pig iron known as SOREL-METAL mainly used in the ductile iron casting industry, an ilmenite ore for blast furnace applications called SORELFLUX and high quality steel billets SORELSTEEL employed in the wire rod fabrication. Moreover , QIT also manufactures high quality iron and steel powders labeled ATOMET for the powder metallurgy industry through its wholly owned affiliate. Quebec Metal Powders Limited. The company operates. rock ilmenite mine near Havre St. Pierre and produces its slag and ferrous products from its metallurgical installations located in the Sorel/Tracy region. QIT. born in 1948 from a joint-venture between Kennecott Copper Corporation and New Jersey Zinc Company, was acquired from BP Minerals by RTZ Corporation PLC in 1989 and remains its wholly owned subsidiary ever since.lImenite is a mineral rich in both titanium and iron oxides. QIT's proprietary mineral enrichment and electric smelting processes permit the concentration of the ilmenite ore and the separation of its main constituents to produce a 80% TiO2, slag and a high purity molten iron which is further transformed into iron ingots (pigs), steel billets, iron and steel powders.QIT's ilmenite deposit is located in the Lake TIo-A1Iard area, 43 km inIand from Havre St. Pierre, a community on the north shore of the St. Lawrence River some 960 km from Montreal. The orebody, covering some 542 000 m2, consists primarily of coarse-grained ilmenite (FeO.TiO2) with disseminated fine lenses of hematite (Fe2O3). The worthless mineral (gangue) associated with ilmenite is mainly anorthosite, a complex silicate. QITs mining operations are carried out using conventional open pit methods in a 500 m by 600 m horse-shoe shaped mine with nine benches developed. Primary blasting is performed on a weekly basis during the mining season. Blasted ore is trucked to the crushing station to be broken down to 15 cm and 7.5 cm sizes, respectively, by means of a primary jaw crusher and a secondary cone crusher. Minus 7.S cm ilmenite is then loaded into hopper cars for the 43 km trip to the Havre St. Pierre terminal where it is stockpiled and reclaimed by under-ground conveyor chutes to a ship loading tower at the dock. The crushed ore is shipped to QIT's smelter located in Sorel in 40 000 tonne carriers from April to December."

Jan 1, 1995

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present investigation flotation was used as a diagnostic to understand the effects of changes to the media during the grinding stage. The observations from flotation for different media are discussed in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. The chemical parameters; pH, redox potential (Eh) and dissolved oxygen (DO) levels were measured. A Base Metal Sulphide (BMS) ore was ground under media of different shapes and compositions to determine the effect of different rod/ball material on the flotation performance of the ore. For a given grind (D80 = 75 µm), media shape had no effect on flotation performance of a BMS ore. Different grinding media had significant effect on slurry chemical properties and flotation performance. Mild steel rods (RMMS) produced the highest solids recovery, nickel and pyrrhotite (Po) recovery, with the highest ethylenediaminetetraacetic acid (EDTA) extractable iron and the lowest DO level. Chrome steel balls and stainless steel rods produced the lowest metal recovery, EDTA extractable iron and the highest DO level. A complementary study was conducted to investigate the effect of using different grinding media compositions, viz, ceramic, forged steel, 15% chrome steel, stainless steel and a mixture of stainless steel and 15% chrome steel (50:50) balls were investigated using a Platinum Group Mineral (PGM), UG2 ore. Grinding products of five different media produced the same solids and water recovery, but the grades and recoveries of Platinum Group Elements (PGE) and chromite were different. Grinding products of ceramic media showed the best flotation performance, with the highest PGE recovery and the lowest Cr2O3 recovery. While grinding products of stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery in the concentrates.

Jan 1, 2016

By James R. Hein, Jane Reid, Robert W. Embley, Se-Won Chang, Randolph A. Koski

"Abstract - This is the first reported occurrence of an active hydrothermal field in an oceanic fracture zone setting. The hydrothermal field occurs in a pull-apart basin within the Blanco Fracture Zone (BFZ), which has four distinct mineral deposit types: (1) barite mounds and chimneys, (2) barite stockwork breccia, (3) silica-barite beds, and (4) silica, barite, and Fe-Mn oxyhydroxide in sediments. All deposit types contain minor amounts of sulfides. In barite stockwork, silica-barite beds, and mineralized sediment, Ba, Pb, Ag, S, Au, Zn, Cu, Hg, Tl, As, Mo, Sb, U, Cd, and Cu are enriched relative to unmineralized rocks and sediments of the BFZ. Fe and Mn are not enriched in the barite stockwork or silica-barite beds, but along with P, Co, and Mg are enriched in the mineralized sediments. Silver contents in deposits of the hydrothermal field range up to 86 ppm, gold to 0.7 ppm, zinc to 3.2%, copper to 0.8%, and barium to 22%.Mineralization occurred by diffuse, low to intermediate temperature (mostly <250°C) discharge of hydrothermal fluids through pillow lavas and ponds of mixed volcaniclastic and biosiliceous sediments. Bacterial mats were mineralized by silica, barite, and minor Fe hydroxides, or less commonly, by Mn oxyhydroxides. Pervasive mineralization of bacterial mats resulted in formation of silica- barite beds. Silica precipitated from hydrothermal fluids by conductive cooling and mixing with seawater. Sulfate, U, and rare earth elements (REEs) in barite were derived from seawater, whereas the REE content of hydrothermal silica deposits and mineralized sediments is associated with the aluminosilicate detrital fraction. Fe-, Zn-, Cu-, Pb-, and Hg-sulfide minerals, Ba in barite, and Eu in all mineralized deposits were derived from hydrothermal fluids. Manganese oxides and associated elements (Co, Sb, Mo, W, Cl, and Cu) and Fe oxides and associated elements (Be, B, P, and Mo) precipitated as the result of mixing of hydrothermal fluids with seawater."

Jan 1, 1999

By Z. Farhat

In spite of advances in cutting tool technology, the understanding of the basic wear behavior and failure mechanisms needs further study. Tool wear is the main factor contributing to geometrical error and thermal damage in machined components. Manifested as a reduction in tool life, it also affects the workpiece surface finish, increases cutting forces and induces residual stresses. Furthermore, the emergence of high and ultra-high speed machining processes necessitates the investigation of tool wear under these severe working conditions. Tungsten carbide-cobalt composite material has been used traditionally as wear resistant materials for many years. One main application of this material is in cutting tools. WC-Co tools consist of hard WC particles imbedded in a tough Co matrix, which functions as a binder phase. More recently, Cubic boron nitride (CBN) tool material have attracted special attention due to its high hardness and excellent wear resistance. Boron nitride in its cubic form is known to be the hardest material next only to diamond. In this paper microstructural and tribological properties of commercial grade WC-Co and CBN cutting tool materials are investigated under high speed cutting conditions. The CBN cutting tools were found to be superior to tungsten carbide (WC) tools. Four-fold increase in productivity and significant reduction in chipping and cratering was achieved for CBN as compared to WC. Wear mechanisms are proposed and are related to the observed wear characteristics in the cutting zone.

Jan 1, 2006

By Fatemeh Pourakbari, Mohammad Reza Yarahmadi, Abbas Sam

Pyrite is the most abundant sulfide gangue mineral in copper porphyry ores. In spite of addition of lime in large quantities to depress pyrite in flotation, considerable amount of this mineral is reported to concentrate, particularly in rougher and scavenger stages. With the Sarcheshmeh pit advancing to a greater depth and reaching to the hypogene zone, the amounts of pyrite and chalcopyrite in the feed are increased. Hence, a reduction in the copper grade and increase in the sulfur content of the concentrate are observed. In this study the effective factors on the pyrite floatability at the circuit flotation was considered at Sarcheshmeh Mine. Mineralization zones in the pit were firstly identified. Then, sampling points were located using GPS system. On the basis of mineralogical composition and morphology, the ore was categorized into five main classes. In this classification the amount of lead and zinc and also pyrite locking with other minerals were analyzed. The study of polished section indicated that inclusion in pyrite was very frequent in all classes, mostly composed of the floatability of pyrite. Flotation tests were performed on the samples of different classes at pH of 11.8 after conditioning time. It was shown that, pyrite floatability was decreased with a decrease in the lead content of the feed samples except for the second class, while for all classes an increase in zinc content contributed to a decrease in pyrite floatability and recovery. It was found that, the lowest pyrite recovery (1.89%) was corresponding to pyrite–molybdenite dominant mineralization with Zn of 0.33% and the highest recovery (86.89%) corresponding to pyrite vein dominant mineralization with Zn equals to 0.9%.

Jan 1, 2016

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By R. Roufail

Mineral liberation is accomplished by comminution and is the first step towards achieving successful downstream processes such as flotation or leaching. In metal mining, one of the most effective comminution methods that is used to grind particles below 10 microns is stirred milling. In this paper the study of particle breakage mode vs. mill operating parameters is addressed. Stirred mills&apos; grinding action is mainly attrition, but operation can be manipulated to include breakage by compression or impact loading. Macro and micro analysis of particle breakage and grinding mechanisms are correlated. Macro analyses convey information that relates grinding mechanism to particle size and shape. It is speculated that the breakage mechanism in the horizontal stirred mills is massive fracture for the coarsest particles and attrition (abrasion) close to the grinding limit where the size reduction ratio approaches 1.0. For micro analysis, the particle breakage mode has a direct impact on fracture type either transgranular or intergranular. Intergranular particle breakage leads to higher mineral liberation compared to transgranular breakage. Similar minerals would have more homogeneous properties that convey a stronger bond compared to dissimilar, heterogeneous mineral bonds. Transgranular fracture requires higher energy than inter granular fracture; trans granular fracture toughness of pure single phase mineral is about 10-14 % higher than the intergranular fracture toughness. This communication presents the results of an investigation to assess how operating conditions can affect trans- vs. inter-granular breakage.

Jan 1, 2009

By J. R. del Castillo, J. Ruiz, N. Kuyucak, J. Chavez

Environmental Impact Assessment (EIA) and Feasibility Studies (FS) were carried out to evaluate the potential use of treated acid mine drainage (AMD) occurring at the Kingsmill Tunnel in the Central Andes of Peru. The 11-km long tunnel drains the underground works of the Morococha Mining District and discharges about 1.25 m3/sec of AMD directly into the Yauli River, which is located within the Amazon Basin. The communities living downstream cannot use the Yauli River water due to its low pH and elevated concentrations of metals (e.g., Cu, Zn, Fe, Mn, As, Cd) and sulfate. Studies carried out for this project included technical feasibility, EIA, economic viability and social impact assessment phases. During the "Technical Feasibility" phase, the treated AMD was produced by simulating a high density sludge (HDS) lime neutralization/precipitation process and was evaluated for various potential uses. Mining companies located in Morococha, in particular Centromin Peru S.A., and the Water Works Company of the City of Lima (Sedapal) collaborated with Golder Associates during the studies. The Canadian International Development Agency (CIDA) provided the financial assistance. The results of the physical, chemical, biological and toxicological analyses demonstrated that the treated AMD could be used for supplementing the drinking water supply of Lima and for agricultural (e.g., irrigation and livestock) and recreational purposes. Process design and scale-up parameters were also determined for the implementation of the full-scale treatment facility to the site. The use of the treated AMD as a drinking water supplement would be economically feasible.

Jan 1, 2004

By C. A. Pickles, K. Mackowiak

Black Thor chromite ore from the Ring of Fire deposit in Northern Ontario was carbothermically reduced in a microwave system to produce a ferrochromium alloy. The as-received ore contained 43.0% Cr2O3, 19.9% Fe2O3, 14.5% MgO, 13.4% Al2O3, and 7.0% SiO2. Activated charcoal was utilized as the reducing agent. Firstly, TGA/DTA and permittivity studies were carried out in order to determine the relationship between the reduction process and the microwave susceptibility. Secondly, microwave reduction experiments were performed on the chromite ore. The variables investigated were; the amount of carbon, processing time, input power and type of atmosphere. A maximum chromium grade of 76.1% and a chromium metallization of 82.7% were obtained for a processing time of 20 minutes, a power input of 800 W, and a carbon addition of 15% in an argon atmosphere.

Jan 1, 2017

By K. D. Peaslee

Slag splashing is an important development that has dramatically improved BOF vessel campaign life and reduced operating costs. This paper highlights research from physical modeling work using a 1/8-scale room temperature model BOF and slag characterization studies from several plants in North America and China. In the model studies, gas flow rate during blow and viscosity of the liquid were found to be two of the most important factors to changing the overall rate of liquid splashed onto the vessel sidewalls. When the flow rate was increased or viscosity decreased, the lower regions of the walls were splashed at a much greater rate. It was also shown that by changing the lance height, more liquid was deposited in the upper regions of the vessel at the expense of lower regions. Reducing the number of nozzles was found to be the most effective method of selectively coating a particular vertical section of the wall. Studies of BOF&apos;s using slag splashing in North America and China showed a difference in the melting characteristics of the final slag. Generally, slag splashing is successful when the melting point of the slag is 220-270°C below the tap temperature to maintain a balance between fluidity and refractoriness.

Jan 1, 2004

By Al Gagnon

Since start-up in 1972, many circuit problems have been encountered, most of which were related to the abundance of fines (-28 mesh), which the circuit had not been designed to treat. The major problems associated with the original circuit included excessive loss of magnetite, reduced throughput during periods of a high proportion of fine coal in the plant feed and low yield in the fine coal circuit. This paper outlines the coal processing circuit at Fording Coal Limited as it exists today, with emphasis on the changes to the original fine coal treatment circuit.

Jan 1, 1978

By G. J. Hamilton

"THE Royalite-Canada Southern Coleville No. 1 gas strike of August 15th, 1951, and the closely following low gravity black-oil strike of August 23rd, were the first of a series of recent oil and gas discoveries in western Saskatchewan. They are in what is now known as the Coleville field, 25 miles north and west of Kindersley and 30 miles east of the Alberta-Saskatchewan border (Figure 1).Gas flows have been recorded in the Viking sand at daily rates of between 5 and 10 million cubic feet, and black oil of 15° A.P.I. gravity is produced from Mississippian sediments of Banff age at a daily rate .of 50 to 100 barrels on pump.Development drilling was carried on during the winter months, with very little attempt at step-out exploratory ventures. This year, however, a step-out programme to the northeast (Figure 2) is •being carried on in order to determine the position of a possible truncation of Mississippian sediments in that direction. Section 30 of the Coleville area has been fully developed on a 20-acre wellsite basis, and structural information is restricted to local rather than regional interpretation. No attempt will be made in this paper to interpret the Coleville area with respect to the regional geology in any but a general manner."

Jan 1, 1952

By R. S. Douglas

Introduction The mine at Copper Mountain of the Granby Consolidated Mining, Smelting and Power Company was one of the pioneers in the use of blast-hole diamond drilling for ore breakage. This method of mining has now been brought to a high degree of perfection. The system in use has?been described in a previously published paper which has become an important part of the literature o the blast-hole drilling method. At the time of the establishment of the system at Copper Mountain, standardized loading and drilling procedures were set up. These procedures were based partly on the results of experiment and partly upon the judgment of men experienced in breaking rock in the mine. The success of the method has been proof of their adequacy. With the progress of scoping in the mine, the diamond drill method of breaking was applied to other ore blocks where different conditions obtained. It was found necessary to make adjustments in the standard procedures to get the best results under the new conditions. The following paper attempts to express, in terms of mathematics, the relations of the variable factors. Until recently, estimations of drilling required were based upon the tonnage to be broken and the proposed rate of explosive loading. A revised method of estimating is outlined below which is direct and which involves no unrelated variable factors.

Jan 1, 1947

By B. I. Whittington

This paper examines the effect of cation type (i.e. NH4+, Na+ and K+) and anion type (i.e. SO42- and C1-) on the extraction of nickel during the pressure acid leaching of a Western Australian laterite ore. The results are compared with testwork conducted with other Western Australian nickel laterite ores and the possible process implications of adding an additive to a plant autoclave are considered. Addition of either (NH4)2SO4, Na2SO4 or K2SO4 increased both the nickel extraction and the acid consumption, provided that the level of additive was not too great. For example, the nickel extraction of 93% increased to above 96% in the presence of additives, but decreased to 94% when, for example, NH4 levels increased from 7 kg/t ore to 21 kg/t ore. The relative stability of the jarosite species formed when additives were present influenced the amount of jarosite in the residue and, hence, both the final free acidity and overall nickel extraction. The use of Cl- versus SO42- salts as additives had little effect on overall nickel extraction or overall free acid values, although the presence of SO42- additives appeared to enhance nickel extraction kinetics over the first 60 minutes of the reaction. In contrast, manganese extraction was enhanced by the presence of Cl- additives.

Jan 1, 2004

By M. Fafard, F. Chevarin, D. Ziegler, H. Alamdari, M Kavand

"Carbon anodes, used in the Hall-Heroult process, are consumed by the electrochemical reaction to produce metallic aluminum. It is also consumed by parasitic reactions with air and CO2. The carbon anode is made of petroleum coke with different particle sizes, butts (recycled anodes) and coal tar pitch. The mixture of fine particles (less than 150 µm) of coke together with the pitch material forms a matrix, binding the large coke particles together. It is generally thought that the binder matrix is more reactive than the other anode constituents. This conjecture was not clearly proved in the literature. The present study is focused on the CO2 reactivity of binder matrix and anode constituents at 960°C, both under chemical regime (100% of CO2) and under a concentration gradient (diffusion). The apparent reaction rates of these materials were measured. The role of the binder matrix in anode consumption and its disintegration (dusting phenomenon) was discussed.INTRODUCTIONThe metallic aluminum production is one of the most important industries in Canada. The Al metal is obtained by the Hall-Héroult process. The principle of this process is the electrochemical reduction of alumina in molten cryolite carried out by an electrical current between carbon anodes and cathode at 960°C (Equation 1). The carbon anode is typically composed of calcined petroleum coke (65 wt.%) and recycled anode (called also butt, 20 wt.%) with coal tar pitch (15 wt.%), playing the role of cement to ensure the cohesion of the anode block."

Jan 1, 2016

By I. Stefanou, J. Sulem

"In the last thirty years, the study of earthquake mechanisms has emphasized the major role of rock friction. Earthquakes appear to be the result of a frictional instability and occur by sudden slippage along a pre-existing fault or a plate interface. Multiphysics couplings play a major role in earthquake nucleation and seismic slip. The effect of shear heating and thermal pressurization may be of prime importance in the control of the stability of shear deformation inside the slipping zone. Other mechanisms in relation with thermal decomposition of minerals affect the pore pressure and the temperature evolution of the system, and can play a significant role in the extreme strain localization observed in field. The actual width of the localized zone is a key parameter for understanding fault weakening mechanisms. On the basis of field observations, laboratory experiments and recent advanced modeling, these phenomena are analyzed and discussed in order to bring some new insights in the understanding of earthquakes nucleation.INTRODUCTIONIn the last thirty years, the study of earthquake mechanisms has emphasized the major role of rock friction. Earthquakes appear to be the result of a frictional instability and occur by sudden slippage along a pre-existing fault or a plate interface (Scholz, 1998; Sykes, 1978). The conceptual model of spring slider system is commonly used to represent the interaction between an elastic crustal block and a fault zone. Stick-slip instability is possible if the softening rate of the shear resistance of the fault zone is high enough as compared to the stiffness of the crustal block. Therefore, weakening mechanisms that can explain how the frictional resistance of a fault decreases with slip and/or slip rate is of prime importance to understand how an earthquake nucleates. In recent years, several drilling programs in active faults (e.g. the Nojima fault in Japan, Boullier, 2011; the Aigion Fault in Greece, Cornet et al. 2004, the Chelungpu fault in Taiwan, Ma et al. 2006, and the San Andreas fault in the U.S.A. Ellsworth et al. 2000) as well as high velocity friction experiments (e.g. Tanikawa et al 2012a; Tanikawa et al. 2012b) have highlighted the physico-chemical processes involved in the nucleation of seismic slip (see for the example the review paper of Niemeijer et al. 2012)."

Jan 1, 2015