Search Documents

By V. A. Leão, M. L. M. Rodrigues, L. C. Sicupira, I. C. B. Rodrigues, T. C. Veloso

Brazilian sulphide ores can contain a significant content of chloride and fluoride, which are harmful to bacteria and thus bioleaching. This work summarizes a four-year research investigation on the effect of fluoride on both bacterial growth and sulphide bioleaching, supported by studies carried out with secondary copper ores. Firstly, the influence of fluoride on the kinetics of ferrous iron bio-oxidation with Sulfobacillus thermosulfidooxidans was addressed. Values as low as 10.0 mg/L F- fully inhibited bacterial growth, although fluoride toxicity could be overcome by the presence of aluminium, which reduced the concentration of hydrofluoric acid through the formation of aluminium-fluoride complexes. This required at least a 2:1 aluminium/fluoride molar ratio, which ensured bacterial growth rate values similar to that observed in the absence of fluoride ions. Subsequently, both batch and column bioleaching with mesofiles (30 ºC), moderate thermofile (50 ºC) or hyperthermophiles (67.5 ºC) of two secondary copper ore samples were analyzed with focus on the relevant effects of fluoride-containing minerals on the bioleaching of such sulphide ores.

Jan 1, 2014

By Ruan Chi, Zhenyue Zhang, Zhengyan He

In order to understand what governs the leaching of exchangeable rare earth (RE) and impurities and enhance the RE leaching process, the effects of the concentration of ammonium sulfate, pH and leaching temperature on the migration of RE and aluminum (Al) during the leaching of weathered crust elution-deposited rare earth ore was studied. The elution curves for ammonium ion (NH4 +) were also studied to reduce the consumption of the leaching agent. It was found that a high concentration of leaching agent can enhance the leaching process of RE and Al, reduce the breakthrough volume of NH4 + and more rapidly obtain the equilibrium of NH4 +. However, excessive leaching agent can both increase the cost and the burden on the environment. There is almost no variation on the elution curves of RE and Al in the pH range of 4-8 and control of the pH of the leaching agent can be omitted. It is better for the leaching work to be done in summer since higher temperatures can enhance the RE leaching process and improve the use ratio of ammonium. Using 0.1 mol/L ammonium sulfate for leaching 250 g RE ore, 95.42% RE extraction can be obtained when the volume of leachate is 102.6 mL. At this moment, only 18.17% of NH4 + is used to exchange RE and 49.22% of NH4 + is left in the leachate that can be reused as leaching agent by replenishing ammonium sulfate. The results of our studies can provide theoretical guidance for high efficiency and low consumption exploitation of RE ores.

Jan 1, 2016

By R. B. Fermor

"The tyndalloscope is used in Europe for dust-hazard assessments in both coal and metal mines. Dust-hazard conditions can be directly evaluated by the tyndalloscope in many underground working situations, once the basic standard table or tables have been prepared from representative mine-rock samples.The tyndalloscope is excellent, in many cases, for diagnostic dust sampling during a working shift, because individual readings can be taken to within three-minute intervals. The limitations of the tyndalloscope are also discussed.The author suggests that a combination of both the tyndalloscope and gravimetric sampling methods would be an ideal match for most mine dust-hazard assessments."

Jan 1, 1970

By G. S. Cole

By 2025, the U.S. automotive industry will have to average 54.5 mpg (4.3l/100km) Corporate Average Fuel Economy (CAFÉ). While new/improved powertrain technology (turbocharging, electrification, diesels, transmissions and stop/start) will be critical, it is estimated that 25-40% of the new CAFÉ standards will require significant mass reduction, and lightweight structural materials will be required. This presentation examines vehicle mass reduction based on new developments in manufacturing automotive structures and components using light metals (aluminum and magnesium), conventional heavy metals (iron and steel), polymers, and carbon-fiber reinforced polymer composites. Components that used to be sand cast or pressure die cast provided minimal fatigue strength and ductility. But greater mass reduction uses more light metals in structural applications. They require eliminating porosity and inclusions to improve ductility and fatigue strength. Improved casting processing, with vacuum die casting, counter pressure and squeeze casting, and new forging and extrusion applications are being developed for this purpose. New grades of ultra-high strength steels can be made thinner, and save over 1/3 the mass vs conventional mild steels. But more complex and expensive processing, such as hot stamping and in-mold quenching, is required. Most engine block structures have migrated from grey cast iron to aluminum over the past 40 years. But compacted graphite cast iron has higher strength at high combustion temperatures and pressures so that high powered engines can be smaller and even lighter than aluminum. Assembling a range of lightweight materials into vehicle structures requires specialized assembly techniques, including sophisticated structural adhesives that can mitigate vehicles’ unique corrosion environment. The presentation will conclude with discussing lightweighting strategies of Asian, American and, European marques and the materials, component designs and assembly techniques used to achieve 2025 CAFÉ.

Jan 1, 2016

By Stanley G. Butcher

Predictions of coal cleaning plant performance from the washability data are traditionally used at the conceptual design stage of a coal preparation plant to confirm process selection. The development of computer programs which simulate the operation of a plant facilitates the optimization of product yield and quality, and ultimately proceeds. It is shown that the optimum is sensitive to changes in mine operations and market price structure. A computerized review of operations is thus recommended as an on-going activity .

Jan 1, 1979

By C-D. Johansson, B. Ögren, B. M. Ludvigsson, K-Å. Johansson, R. Lindh, G. Berg, M. Maliarik

This paper presents the High Current Density (HCD) Silver Electrorefining Process. A 25-year history of development of the silver electrorefining process as well as associated equipment is given. The process is simple and robust, but at the same time highly automated. With low operating costs and man power requirement it allows consistent production of 99.99 % quality cathode silver. The process ensures that no toxic gases are formed in the working environment. Silver Electrorefining is a heart of a Silver Refinery plant covering the complete range of processes from casting of silver Doré anodes to casting of the bars of refined silver or/and silver granulation. The process has been successfully applied at 11 installations world-wide with plant capacities ranging from 30 to 1500 tpa.

Jan 1, 2014

By N. E. Nelson

"The Hidden Creek mine is about l~ miles north of the north end of Granby bay; a nearly landlocked body of water on the west side of Observatory inlet; 90 miles north of Prince Rupert; British Columbia.The main haulage way of the mine at 385 feet above sea-level has been driven north into the somewhat precipitous end of a north-south ridge that rises from the tide flats between the east and west forks of Hidden creek. The outcrops of the principal orebodies, two prominent bluffs of stained rocks and sulphides, were higher on the face of the ridge and extended from about 530 to 850 feet elevation. North from the bluff tops, the ridge comb rose gradually to about 1,200 feet elevation. The name of the discoverer and the date of discovery of the Hidden Creek orebodies are probably unknown, but the discoverer is believed to have been an Indian from one of the reservations along Observatory inlet. The deposit was brought to the attention of John Flewin, Government Agent at Post Simpson, near the beginning of the present century. Mr. M. K. Rodgers, developer of the Nickel Plate mine at Hedley, did the first organized work on the deposits. Next the Hidden Creek Copper Company prospected the property. Rodgers acquired the prospect a second time, did more work, and finally in 1910 optioned the property to the Granby Consolidated Mining, Smelting and Power Company, Limited, at that time operating at Phoenix and Grand Forks in the Boundary district of British Columbia. The optionees stepped up the development work and brought the property to production in 1914. The ores were direct smelted until 1924. In that year a mill was built. From 1930 until the end of the productive life of the properties in 1935, all of the ore was milled and the concentrate smelted. From March 17, 1914, until July 31, 1935, the production from the Hidden Creek mine was, in round numbers, 18,000,000 tons of 1.70 per cent copper ore and 6,000,000 tons of low grade dilution rock. The Hidden Creek mine ""died with its boots on"". During 1934 the average monthly production was 146,377 tons of 1.06 per cent copper ore. For 7 months of 1935 the average was 161,750 tons of 1.03 per cent ore, and for the final month, July 1935, the production was 156,950 tons."

Jan 1, 1954

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"The McClean uranium deposits are in northern Saskatchewan, 11 km west-northwest of the Rabbit Lake mine. Their average grade is 1.8% UJ0 8 and they contain 6,350 tonnes of uranium oxide in seven pods of variable grade and mineral assemblage. They are hosted by both basal Athabasca Group and the regolith developed on the underlying crystalline basement. The major mineral facies are: sulphide, arsenide, 'bleached', and hematite, with the important uranium minerals being coffinite, uraninite and pitchblende.Abundances of carbon and sulphur isotopes are consistent with their derivation from pyritic graphite in basement gneisses. Isotopes of oxygen and hydrogen suggest mineralizing fluids were aqueous and at temperatures of about 200°C. Ar39/ Ar40 laser age determination of illite indicates mineralization began about 1300 m.y, ago and that significant hydrothermal alteration ceased about 1170 m.y. ago though Pb/U data suggest the deposits continued to evolve into the Mesozoic.The deposits are interpreted as the result of oxidizing ground water stripping uranium and other metals from either the Athabasca sandstone, especially the heavy mineral layers, or from the regolith, and precipitating these when encountering a warm reduced fluid emanating from the basement."

Jan 1, 1984

By E. A. Haack, L. A. Warren

Microbial biofilms are essentially biologically driven, geochemically reactive interfaces between solid surfaces and aqueous solution. Field investigation of acid rock drainage (ARD) associated biofilms at the Onaping nickel mine (Onaping, ON, Falconbridge Ltd.) characterizing: (1) micro-geochemical gradients (pH and 02) (2) metal fractionation amongst biofilm solid components, and (3) microbial communities; over both seasonal and diel timescales, indicates biofilms are highly metal reactive. Results show that biofilms accumulate metals seasonally within two microbially controlled solid fractions: amorphous hydrous manganese oxide (HMO) biominerals and the organic biofilm matrix. The biofilm geochemical microenvironment, driven largely by microbial activity, dynamically impacts biofilm metal behaviour over diel timescales. These results indicate that microbes can play significant roles in bulk system reactive metal transport. On-going investigation seeks to characterize the microbial players and the microbial-geochemical linkages involved in Mn oxyhydroxide formation and subsequent metal sequestration, with the goal of engineering this microbial activity as a bioremediative approach. This approach will have utility beyond specific application to the Falconbridge Onaping site to ARD mine environments in general, as the likely microbes involved in these processes are typically common across ARD systems.

Jan 1, 2004

By Balmer Neilly

We are regularly told that before making a new investment one should seek the advice of his banker. If we were to place the subject matter of this paper before bankers. other than those who have experience in our mining camps, their reply would probably be evasive. However, if for example: a mining company asks them for a loan and offers as security certain mining investments, they are, in most cases, explosively candid. The idea is preposterous, unless, under Section 88 of the Bank Act, the mining company is able to deposit with the bank, gold or silver bullion, to an amount sufficiently in excess of the loan, to provide for what the banker describes as a reasonable margin of safety in case of contingencies. In addition the directors of the mine personally must jointly and severally guarantee payment of the loan. With any of these conditions missing the banking atmosphere becomes chilly. The local manager explains that the general situation, and particularly European conditions, are so unsettled that head office has warned him that his discretionary powers must not be exceeded under any circumstances.

Jan 1, 1924

By A. M. Simons

Cyanide destruction by Caro’s acid is one process commonly employed by gold operations to meet regulatory requirements and/or the International Cyanide Management Code compliance for weak acid dissociable (WAD) cyanide in cyanidation tails or waste water from such operations. Typically smallscale bench tests to evaluate and assess the suitability of the Caro’s acid destruction process are conducted. Additionally, the experimental procedure used during these preliminary investigations may also differ from that implemented at the full-scale. This paper presents the results from a fundamental investigation of the Caro’s acid process to establish a more detailed understanding of the impact that the experimental procedure has on the destruction of cyanide. In particular, it was found that the control of pH was important to avoid copper(I) cyanide precipitation at low pH and maximise WAD cyanide destruction. Residual peroxide in the preparation of Caro’s acid has the potential for subsequent cyanide destruction and could be exploited.

Jan 1, 2014

By P. C. Santos-Munguía, F. Nava-Alonso, O. Alonso-González

"The gold recovery of a Mexican cyanidation plant, in Sonora, has been decreasing due to the increasing presence of gold tellurides. This work presents the results of different processes aimed to recover the remaining gold from the cyanidation tailings of the operation. The cyanidation in the mine is performed at 0.1 g/L NaCN and pH = 10.3, adjusted with lime. The treatments studied in the laboratory with these tailings were: cyanidation at higher cyanide concentration than that used in the plant, cyanidation with oxygen injection, cyanidation with oxygen and lead nitrate addition, and thiourea leaching. The results obtained with each of these treatments are presented and discussed with the final objective of proposing a method to recover the gold associated with tellurium.INTRODUCTION It has been demonstrated that gold telluride is refractory to the conventional cyanidation process and, for this reason, some alternative methods to recover precious metals from tellurides have been proposed. (Zhang et al., 2010). These include cyanidation with modified conditions or the use of non-cyanide leaching agents. This work presents the gold leaching results of tests performed with a sample of cyanidation tailings obtained from a Mexican deposit containing telluride species. The mine exploits a mesothermal deposit with a molar Te/Au ratio of 1, containing also lead, molybdenum, bismuth and tungsten. Gold is recovered from the ore by standard cyanidation, however, lately the gold recovery has decreased, likely due to the tellurium content of the ore. The sample used in this work was the cyanidation tailings of this deposit. It was treated in the plant by cyanide heap leaching (0.1 g/L NaCN, pH = 10.3 adjusted with lime). Some gold remained after the cyanidation and it was thought that this gold was associated with tellurium. The objective of this work was the recovery of the remaining gold from the tailings by an alternative process."

Jan 1, 2017

By A. C. Stevenson

"The most common theory is that, since thyristors, diodes, and insulated gate bipolar transistors (IGBTs) are “solid state” they will live forever. This is not so. They have wear-out mechanisms (e.g. insulation) and other mechanical parts such as motor bearings. These wear-out phenomena can be easily calculated. In this paper we will look at some of the failures and the failure rate of thyristors in power converters to see what affects them and to see what improvements can be made. If converter failures do occur, some simple forensic engineering steps will show if this is the root cause of the problem.IntroductionLook at the general failure rate curve for thyristors, diodes, gate turn off devices (GTOs) and IGBTs shown in Figure 1. We see that there is an initial high failure rate due to manufacturing defects, application problems, and drive start-up stresses that lasts for a few weeks. This is followed by a long period of (hopefully) several years with a relatively low but very slowly rising failure rate. At the end of this period, the devices start to wear out and the failure rate suddenly starts to increase rapidly over a few months. This signals the end of life for the devices in the system. We will start by looking at this end of life area."

Jan 1, 2000

By J. G. Kelly

"IntroductionOver the past twenty-five years of improvements to scooptrams In the Ontario Division of Inco Ltd., records indicate that on average, an 8 yard capacity machine at 80% availability will load, haul and dump about 100TPH from an average stoping area. This, essentially, means that Inco mines are limited to 2000 TPD as an approximate maximum production cap per minute. Some of the improvements made to scooptrams over this period have been:• dry disc and oil immersed brakes on larger loaders;• to replace air over hydraulic systems;• modulated shift transmissions;• greater breakout and tramming capacities by using larger engines and buckets;• operators' compartments have been enlarged and better seats,• joystick controls and air-conditioned cabs have been utilized'• major cost savings have been realized through tire maintenance improvements; and• major savings, safety improvements and increased ore recovery by using remote controls.After reciting the improvements listed above, and the list is by no means exhaustive, it is quite obvious that scooptrams are a mature product and that major design or performance improvements will not occur in the futre. Any futher improvements will be incremental in nature. Loading, hauling, and dumping with scooptrams is a batch process and as such is limited in its total output.Continuous Load/Crush/Convey Systems:In order to improve productivity, a radical new system was required. The target was 2000 tons per shift. In 1984, to meet the goal, Inco acquired the rights to a contiunous loader from Canadian Mine Services. Inco made modifications to the original prototype machine, such as: (I) conversion from rail mounted to crawlers for increased mobility; (2) a hydraulic cooling system was added; (3) flight bars were changed from cast to forged; (4) motor horsepower increased to 200 hp from 150 hp. Emerging from these modifications came a machine known as the CL-looo Oscilloader (Fig. 1).The CL-looo Oscilloader is an electric hydraulic 35-ton machine which is crawler mounted and has a drawbar pull of 30 tons. It has an adjustable frequency, oscillating lip which simulates the digging action of a manual .shovel. This action agitates and lifts the muckpile enough to allow it to settle by gravity onto the chain and flight conveyor table which then removes the ore to the tail end for discharge into either a crusher, a conveyor, a truck, or a combination of these.Late in 1985, six oscilloaders were fabricated and put into Inco mines for field trials. At Creighton Mine some early field trials were conducted with a rail mounted continuous loader loading directly into 140 cu.ft. Granby cars. Much of the field testing was in VRM drawpoints with the Oscilloader loading into 20-ton trucks or into Teletrams . At Levack Mine, by puttmg the truck on remote control, it was possible to have the operator run the Oscilloader and load his own truck (Fig. 2). At McCreedy West Mine, Copper Cliff North Mine, and Copper Cliff South Mine, the Oscilloaders discharged directly into 26-ton trucks."

Jan 1, 1988

By Trevor McGiddy

"Australia's prosperity relies significantly on income generated from exports of resources and agricultural products. In 1989-1990, coal was Australia's most valuable export commodity, contributing. A $5.7 billion or 14% of all export income.The abundance and quality of its coal resources and the proximity of Australia to the rapidly developing economies of Southeast Asia were significant factors that encouraged export-oriented growth and investment and will continue to do so. On the other hand, the 1980shighlighted the sensitivity of the industry to international changes in supply and demand, currency and socio-political forces.Following many years of disappointing returns for investors, mainly as a result of falling Australian dollar coal prices, resolve will be necessary to maintain competitiveness with resource-rich nations. In recent years, operators, unions and governments have begun to embark on a long overdue rationalization of domestic issues in a bid to increase productivity and reduce costs.The nature of mining operations is also changing; deeper surface mines and the growth of longwall mining will require the development of new technology and skills. Other challenges emerging from the international environmental debate will require that Australia responds appropriately to demands for cleaner fuels, energy efficiency and environmental responsibility.The future development of the Australian coal industry will therefore be influenced by its own ability to become more efficient and mature in the production of quality coal products and through rational international response to environmental questions."

Jan 1, 1992

By G. M. Ritcey, M. Silver

"The processing of uranium ores produces tailings that could constitute environmental problems. At most operations the tailings are dumped into a designated area, with the ultimate acid drainage occurring if sulphides are present, together with the release of metal constituents to the rivers and streams. If the chemical reactions occurring within the tailings could be predicted, perhaps methods could be developed to either increase or decrease 'the rates of reaction. One such study has been in progress at CANMET during the past three years. The paper describes the use of Iysimeters containing low-grade and complex uranium tailings to determine the effects and interactions of bacteria, sulphides and solvent extraction organics on the release of radionuclides and on acid production. A simulated rain cycle nine-fold the normal was used and the Iysimeters were subjected to timed intervals of light and darkness. As a result, the tests simulated a 25-year period.IntroductionAlthough Canadians derive major benefits from uranium, there are environmental and health consequences, not yet fully understood, from the associated mining and milling operations. A major project at CANMET (Canada Centre for Mineral and Energ y Technology) has the ultimate goal of ensuring that any adverse effects on man and environment, now or in the future, resulting from the processing of uranium should be acceptably low. The magnitude of the task was exacerbated by the fact that the increased demand for electrical energy and the resultant increased prices for uranium oxide during the 1970s led to a rapid expansion in the industry. Annual world demand for uranium was expected to increase 12-15 fold in the next quarter century, with annual requirements of between 200,000 and 300,000 metric tonnes anticipated by the year 2000. Currently, the demand is low and the prices for the oxide have decreased."

Jan 1, 1982

By W M. Cameron

Geophysical studies have extended seaward in recent years, and the important discoveries which have been made have led to a better understanding of geological processes. A present source of certain minerals, the sea will eventually serve as an important source of desalinated water. The continental helves, in particular, represent a potential mineral resource. The expansion of Canadian oceanographic effort that is now underway will eventually lead to the exploitation of the wealth beneath the sea. THE subject of this symposium, which emphasizes the word "geophysics," the specialties of the speakers who are contributing and the nature of the audience at first made me believe that I, a a physical oceanographer, would be out of place. However, I shall undertake to classify myself as a geophysicist, and shall arrange my remarks on my specialty o that they might be of interest to those of you who are predominantly geologists, metallurgists or mining engineers.

Jan 1, 1963

By B. F. Giyani, D. Rahal

"Stirred media mills have proved to be more energy-efficient than the conventional ball milling for fine grinding applications. The mill performance is governed by a number of operating variables including mill stirrer speed, feed particle size, solids content and slurry rheology. A study was conducted to assess effects of mill speed, media size and density, and slurry density on the Stress Intensity (SI) in a VXPmill and thereby the relationship to mill performance. For the mill speeds tested, it was found that the optimum tip speed is 7 m/s. If the speed is too high (12 m/s) energy losses result due to mechanical friction losses and heat generation. If the speed is too low (3 m/s), the kinetic energy is not sufficient to promote breakage. The size reduction ratio increases with the increase in mill speed and the decrease in solids content especially in the coarse fraction particle sizes. The effect of slurry rheology on mill performance was shown by assessing the effects of increasing solids concentration and decreasing particle size. Rheological effects seemed to interact with mill speed such that the mill was less energy-efficient at higher solids content and at higher mill speeds particularly for grinding to fine particle sizes. There is an opti"

Jan 1, 2017

By N. E. Izatt

Molecular recognition technology (MRT) has a wide range of applications in the hydrometallurgical and chemical processing industries for the selective removal of iron as well as various other impurities from a variety of streams, including aqueous solutions through a wide pH range, as well as organic solutions. An example of a commercial application is provided for the removal of iron from an aluminum chlorohydrate stream. In this example, MRT has a selectivity for iron relative to aluminum which is significantly higher than that of ion exchange resins. A discussion of MRT capabilities for other impurities and streams is also provided.

Jan 1, 2006

By H. Nouranian, M. Askari

GOLGOHAR Mining & Industrial Co., with annual production of 16 million tons, is one of the largest pelletizing and iron ore supplier in Iran that recently this year, because of using mineral processing techniques and extraction of ore body positioning between the metamorphic rocks, about 150 million tons of dry tailings has been created as a result of concentrate production. On the other hand, many environmental issues such as groundwater pollution have been developed by sulfide and silicate gangue minerals, which containing heavy metals such as mercury and arsenic. In this study, a new product with high added value has been introduced for the company by identification and extraction of industrial minerals in dry tailings. Also, by removing large masses of dry tailings, environmental pollution sources were gradually eliminated. This method can be used as a modern waste management approach in the world.

Jan 1, 2017