Search Documents

By Š. Šachlová, T. Lokajícek, M. Petružálek, T. Svitek, A. Štastná

During the past 20 years, alkali silicate reaction (ASR) as a cause of concrete deterioration has been studied by a wide range of experimental methods such as microstructural and macrostructural analysis, bulk chemical analysis, X-ray and neutron diffraction analysis, etc. All of these data are compared with expansion values of mortar bars (following ASTM standard C 1260). Recent studies indicate the useful application of non-destructive methods with the aim of better reflecting mechanical properties and the degree of deterioration of real concrete. Ultrasonic testing methods (including ultrasonic pulse velocity UPV) are widely used to determine material mechanical properties and the changes induced by a variety of mechanical or chemical processes. However, only a few laboratory studies of ASR focused on ultrasonic testing of mortar bars. Due to this fact, a heating chamber was designed and constructed to enable ultrasonic sounding of mortar bar specimens while stored in accelerating solution. Regular ultrasonic sounding of mortar bars reveals significant dependence of ultrasonic data such as longitudinal P-wave velocity, signal energy, signal amplitude and signal frequency on mortar bar storage time. Ultrasonic data were subjected to time domain as well as frequency domain analysis. Different storage conditions were used to determine the effect of ASR on ultrasonic parameters. Mortar bars, prepared in the same manner with one type of aggregate, were stored in cold or warm water or in an accelerating warm medium. Ultrasonic data accurately reflects the differences in hardening and deterioration of tested mortar bars due to different storage conditions. Ultrasonic results showed very good correlation with the results of ASTM standard expansion tests and much higher sensitivity to ASR-induced concrete deterioration. Expansion tests showed 1% measured length differences in comparison with up to 80% resolution of ultrasonic data. The ultrasonic testing proved to be a suitable laboratory method for investigating ASR-related processes and could lead to an improvement of standard testing procedures.

Jan 1, 2015

By E. V. Neelands

THE Canadian Malartic mine is in Western Quebec, about fifty miles east of Noranda and forty miles south of Amos on the Canadian National railway. The recently constructed branch of the railway from Rouyn to Senneterre passes half a mile north of the mine. HISTORY he property was discovered in 1923 'by St. Barbe Sladen, H. S. Kennedy, and J. C. Carroll, who were prospecting for an Ottawa syndicate and found gold in a small quartz vein near the present workings. Five claims were staked and were optioned to an exploration company, who allowed the option to lapse after surface sampling and diamond drilling eighteen holes. Some months later, the property was sold to Malartic Gold Mines, Limited, who carried on development until 1929. A vertical shaft was sunk and exploration work done on three levels, supplemented by diamond drilling 16 surface holes and 62 underground holes. The work indicated that the important ore occurred in two silicified.zones in schisted greywacke which intersected west of the shaft and were believed to be controlled by a drag-fold. The ore grade was not considered sufficiently favourable to war-rant an operation, and work was terminated. With the advance in the price of gold to $35 per ounce, interest was revived and a new Company, Canadian Malartic Gold Mines, Limited, was incorporated for further development. The shareholders of the old Company accepted a new position under which their interests were protected, and sufficient treasury shares were optioned to Ventures, Limited, and Sudbury Basin Mines, Limited, to provide funds for further exploration of the prop-erty to determine whether, under the new economic conditions, profitable operation would be possible, and, if advisable, to provide the equipment for production. Additional claims were acquired, bringing the total area up to 1,029 acres.

Jan 1, 1939

By H. G. Wang

The production process of a coal mine can often be interrupted by all kinds of events scheduled or unscheduled and thus often needs gas drainage for a temporary or long-term sealed area. Gas drainage has a relatively high risk, therefore attention must be paid to its design to keep the process safe. Based on the conservation laws of mass and constituents, and under the conditions of the allowable gas concentration limit in the return air route, the relationship between gas concentration and gas drainage flow rate as a function of time during the drainage process is discussed in detail to build a mathematical model of gas drainage from a sealed area. With respect to the gas drainage process, two different conditions need to be considered: one with a methane free fresh air supply, the other with a low gas concentration. This paper presents the derived mathematical models for these situations and then shows that they can be incorporated into one model with some modification. This combined model can be employed to determine the optimum gas drainage flow rate with the shortest drainage time. The application is coded using the C# programming language within the .NET framework. Finally, the application program developed by the author is used to validate the mathematical model through an example of gas drainage with varying rate.

Aug 1, 2013

By H. J. Handewith

"After having performed qualitative and quantitative tests on nearly 550 rock specimens from tunnel projects throughout the world and comparing the results with actual boring in eight distinctly different rock types which varied in compressive strength from 12,000 to over 34,000 psi, it has been concluded that any rock -andesite, granite and even taconite -can be machine-bored. The question is -can it be bored economically? The intent of this paper is to delineate the investigative needs to accurately and reliably answer this question. A piece of NX core in the hand represents less than 50 per cent of the worthwhile geologic information that could have been obtained from a given core hole. A thorough site investigation by competent personnel can gene-rally foretell to what extent, if any, varying geologic conditions will hinder machine progress.A laboratory testing technique has been developed that has been correlated well (80 to 120 per cent) with actual boring results. This technique will be discussed in detail. Rock cutter life is a function of the penetration rate and the forces required to sustain that rate. Cutters are now, and will be for .some time to come, the single, most expensive consumable item involved in continuous tunneling in hard rock. It is by strict attention to predicting these rates and forces that tunneling costs can be optimized."

Jan 1, 1970

By J. Tuominen

Outokumpu Direct-to-Blister Flash Smelting is currently in operation in two smelters, a third one is under construction and a fourth one is in the design phase. The two smelters in operation are the Glogow 2 smelter of KGHM Polska Miedz S.A. in Poland and the Olympic Dam smelter of BHP Billiton in Australia. The Outokumpu Direct-to-Blister smelter of Konkola Copper Mines Plc. in Zambia is under construction and the new smelter of Glogow 1 is under design and waiting for final go-ahead decision. Additionally, the Garfield smelter of Kennecott Utah Copper Corp. makes blister copper out of matte in a Flash Converting furnace. A similar operation is under construction for Y anggu Xiangguang Copper Co. in China. The slag cleaning process, which is needed to clean the slag of the Direct-to-Blister Flash Smelting Furnace, has different requirements depending on the feed to the flash furnace. These differences are discussed in the paper. The differences between the processes and slag produced are discussed as well as the metallurgical requirements for slag cleaning. The Direct-to-Blister process, where the blister copper is produced directly from concentrate in one step, requires at least a partial treatment of the slag in an electric slag cleaning furnace. The existing impurities determine the specific requirements of the actual cleaning process. The different processes are discussed in the paper. The newest developments of Outokumpu Technology Oy for electric slag cleaning furnace design are presented as well as the characteristics which the furnace shape gives to the process.

Jan 1, 2007

By Roger K. M. Bellows

The last coal-fired power plant to be built in Canada came into operation in 1994. Since then, Canada?s electricity requirements have grown substantially but no new coal-burning plants have been built. This country has abundant resources of coal from coast to coast, but in recent years, this has not affected our choice of fuel. In many other countries this is not the case, and the use of coal is growing rapidly. Although this presentation covers the topic from an Alberta perspective, some of the conclusions can be extrapolated to the rest of the country, and perhaps even to other countries. The coal found in the Alberta plains is particularly attractive because of its low cost and low sulphur content. Yet coal is no longer the fuel of choice, and a long-standing provincial government policy to favour coal for electricity generation has been ignored for more than a decade. Considering the lack of good alternatives, it seems obvious that we should look to coal as our primary energy source in the generation of electricity and for other industrial applications. This paper discusses some of the reasons that coal has fallen out of favour, particularly with respect to electricity generation. The significance of the deregulation of the electricity industry will not be ignored. In addition, the author will offer his opinion on the question of what it will take in order for coal to once again become the favoured fuel.

May 1, 2001

By E. Yan, M. Mankosa, E. Wasmund

"Rougher flotation in sulfide ore applications is typically performed using conventional flotation machines. The trend over the last 100 years has been for these cells to become larger in volume with cells reaching sizes of 600 m3 and in some cases even larger. The associated foundation loadings, transport and installation requirements along with building size have also increased. In an economic environment where projects must be executed with dwindling capital supply, bigger is not always better. More recently, industry is being challenged to identify new technology that allows for improved flowsheets and financial returns through efficiency gains. To meet this challenge, a novel high-intensity two-stage flotation system known as the StackCell™ was tested to potentially achieve installation volume and required retention time gains when compared to conventional flotation circuits. The results from on-site pilot scale work conducted on typical copper concentrator rougher flotation feed showed retention time gains on the order of 6 to 9 times when compared with conventional flotation equipment. This finding has the potential of reducing capital demands for rougher flotation circuit designs when incorporating the StackCell. The results from test work will be discussed in this paper showing comparative test data generated with a Denver bench batch test, pilot StackCell and large conventional cells, all receiving the same feed.INTRODUCTION Over the last few years, a number of flotation devices have been described as two-stage or multi-stage flotation units. The idea behind multi-stage flotation devices is that flotation performance can be improved by utilizing cells with multiple specialized units in series, but not all units of the same type, as is practiced in trains of multiple tank cells or columns. Instead, each unit is specially designed to provide the optimized fluid environment for each stage of the sequential flotation process. This idea has been proposed based on a study of the fundamentals of the flotation process, and the realization that the process consists of discrete sequential processes, that are each optimized with dissimilar process conditions (Finch et al, 1995), (Zhou, 1996). Instead of executing each step simultaneously in a homogeneous fluid environment, where the conditions would be a compromise between particle collection and froth recovery, the multi-stage flotation unit operates in a set of segregated process environments, each with a set of conditions optimized for that step."

Jan 1, 2018

By George Kellock

In presenting this paper for discussion at the Western Annual Meeting to be held in Edmonton, it is with the idea of creating a full and general discussion by the mining men in the Province as to the best way to eliminate, or at least hold down to a minimum, the dangerous coal-dust which is made in mining pitching seams in our Alberta mines by the chute method. Also, an alternative method is outlined, whereby the percentage of lump-coal mined can be increased, and the mining costs reduced-although the paper does not go into any detailed consideration of costs. The general trend of mining practice and lay-outs is at present towards mechanization, and the results being accomplished by the substitution of machines for manual labour are fully justifying the changes. In the technical mining journals, there are published from time to time papers dealing with a variety of methods of mining, which are descriptions of actual operations, and a great deal of interesting and valuable data is given as to the comparative values of the different methods, insofar as the percentage of grades of coal produced, the cost of production, etc., are concerned; but the mechanical methods described in these papers are nearly always suitable only for flat seams, or seams with a very low inclination.

Jan 1, 1929

By M. S. Badollet

Introduction The manufacture of some asbestos products involves the use of asbestos in combination with water, cement and granular fillers. This type of production is often called the wet or semi-wet process and requires the use of either pressure or vacuum to eliminate the excess water in the fibrous blend so that the product may develop the proper strength during the curing stage. Asbestos - cement products available today are numerous and are a valuable contribution to the building industry. Their production in quantity depends upon the type of equipment employed, the speed at which it can be operated, and the factors involving the? blending of asbestos, cement, water, and fillers. Assuming that all mechanical troubles at a plant have been eliminated or are under control it is still advisable to study the basic properties of the raw materials used in the asbestos-cement products. The type of cement used is an important factor, but usually the manufacturer of the cement is willing to work with the asbestos development engineer and recommend the proper type to be used for the product. The source of the water should not be overlooked as a general factor involved in the production cycle. Waters containing a high percentage of contamination such as silts, humus, or soluble salts may adversely affect the setting of the cement or cause a slowing down of the production rate in the factory. Asbestos in combination with cement is an ideal material fo1 building products. It is inorganic, will not deteriorate, and can be handled by mechanical equipment with a minimum reduction of fibre length. The many physical properties peculiar to asbestos fibres should be well understood by the manufacturer. They may be briefly enumerated as follows: fibre strength, fibre composition, sliminess, length, harshness, softness, and filterability or porosity. This last named property is important and it is the purpose of this paper to present some basic studies on filtration as applied to production problems.

Jan 1, 1949

By M. Lindgren

"Hydrometallurgical processing involves process stages, like leaching, that create harsh environment for stainless steels. High acidity, the presence of chlorides and oxidizing ions combined with relatively high temperature create risk for both uniform and localized corrosion. Advanced electrochemical techniques were employed to study uniform and pitting corrosion of two stainless steel grades 316L and 2205. Results obtained with the linear polarization resistance technique combined with the harmonics distortion analysis, electrochemical noise and coupled multielectrode array systems are compared to the results of conventional electrochemical techniques and immersion tests.INTRODUCTIONHydrometallurgical processing has become favoured in metals production in recent years due to energy costs, leaner ore bodies and environmental factors. Because the hydrometallurgical processing route is flexible, various types of secondary raw materials, like flotation tailings, dusts, sludges and slimes can also be treated in addition to conventional mineral concentrates (Sarveswara Rao & Acharya, 2008).Hydrometallurgical processing relies on aqueous chemistry, usually acids, at temperatures around 100°C for the recovery of metals from ores, concentrates, recycled or residual materials. The processing route can typically be divided into three stages: leaching, solution concentration/purification and metal recovery. The processing environment is aggressive, especially in leaching. High acidity, relatively high temperature together with impurities, like chloride ions, place high demands on the corrosion resistance of construction materials. The dominant corrosion mechanism may be uniform corrosion or localized corrosion depending on the process conditions (Ekman & Torsner, 2010). This complicates the prediction of corrosion rates and, consequently, cost effective material selection.Traditional means to evaluate uniform corrosion resistance of stainless steels are immersion tests and the results are published in the form of iso-corrosion diagrams (Outokumpu Stainless, 2010). For the localized corrosion, namely pitting and crevice corrosion, immersion tests can be used but the duration of the test is rather long because an incubation period takes place prior to the occurrence of the actual localized corrosion damage. Electrochemical techniques, traditionally in the form of cyclic polarization scans, have been employed to assess the susceptibility of a material to pitting corrosion (Papavinasam, 2008). They cannot, however, give any indication of the pitting corrosion rate and lack potential for on-line measurements."

Jan 1, 2012

By D. S. Hines

The purchase of mechanical equipment for mines is not unlike the purchase of other materials or supplies in general principle, but on account of the major part such equipment plays in the operations, and of the fact that life and valuable property are at stake, the matter demands the most careful attention on the part of the purchaser. The problems and difficulties encountered are dealt with below in their sequence in the purchasing procedure. Requisiting Although it is quite a common practice to submit a tentative specification of requirements to recognized manufacturers of equipment- soliciting alternative propositions or recommendations for study in the selection of certain equipment-as a rule the first step in purchasing procedure is the requisition. Primarily, it is the form that carries to the purchasing department the record of equipment wanted. A full and complete description or specification, and accuracy of record, are the important points to be insisted on in a requisition. Too much attention cannot be given to this detail, as this is one of 'the most important phases of purchasing work. Incomplete information, either in specification or detail, leads to delay in handling the requisition, and, if not detected in the purchasing department, may mean receipt of material which cannot be used for the purpose intended. In addition to description of material or equipment to be ordered, the requisition should also show where or what the equipment is for, whether for operating or new work. If for capital account, the number of the authority for expenditure should be given for record and distribution purposes.

Jan 1, 1930

By M. W. Grabinsky, P. B. Tomory, J. Carvalho, J. H. Curran

Many underground mining operations use Split Set friction stabilizer bolts for rock support. Currently, however, little has been done to quantify the effects of various rock mechanics and operational parameters on the capacity of frictional support systems. The strength of Split Sets is usually measured by means of a pull test wherein a jacking force is applied to the bolt and a slip load is obtained. In order to evolve a rational design procedure for this type of support, an extensive database of over 900 pull test results from more than 50 mines through- out North America has been assembled and analyzed. Associated relevant rock mechanics parameters (rock type and quality) and operational details (drilling method, bit size, drive time, time to pull test) were also obtained, as completely as possible, for each test. Analysis of the information has yielded several charts that relate pull-out strength to relevant parameters and simple statistical analyses were conducted where necessary. Quantified distributions for pull-out strength were also produced for several operating conditions. The factors that most significantly affect bolt strength have been identified and specific applications to design are discussed. The information presented will assist mining engineers in designing safer and more economic support using Split Sets.

Jan 1, 1998

By G. Binks

In 1997, the Zinifex Hobart Smelter ceased ocean disposal of jarosite and the flowsheet was converted to reject iron as paragoethite. This paper describes the evolution of the flowsheet since the changeover and considers future flowsheet developments. The major change to the flowsheet has been an increase in the silica content of the calcine resulting from treating increasing levels of Century concentrate. The high silica levels impacted on the paragoethite precipitation stage, causing a deterioration in the settling and filtration characteristics of the paragoethite and an increase in the contained zinc level. The implementation of a two stage neutral leach step has enabled the flowsheet to cope with the higher input silica levels. Future developments include an understanding of the form of the zinc in the paragoethite and options to lower the zinc level to improve the overall zinc recovery.

Jan 1, 2006

By D. Raicevic

Interest has recently been revived in the recovery of tantalum from the Bernie Lake pegmatite deposit. A gravity concentration process was developed to give satisfactory recovery and concentrate grade. The application of high-intensity magnetic separation was also stud1ed. A pilot-plant investigation that confirmed the laboratory testing and provided a commercial-grade concentrate 1s described.

Jan 1, 1968

By Michio Okada

Dissociative adsorption of hydrogen (deuterium) on thin gold films grown on Ir{111} surface has been studied with temperature-programmed desorption using a quadrupole mass spectrometer and nuclear reaction analysis. Thin Au{111} films are epitaxially grown on Ir{111}. Surprisingly, H2 (D2) can dissociatively adsorb on these Au{111} films, although it is well known that Au surfaces are noble enough not to dissociate hydrogen molecules [B. Hammer and J.K. Nørskov, Nature 376, (1995) 238]. We attribute this to the sensitivity of hydrogen to changes in the local surface properties, e.g., electron localization (the narrowing of the s-band, the s-band center model), which could explain the upto now unexpected high for the reactivity of a thin Au{111} surface. Moreover, we found that H (D) atoms can be confined into a Au thin film and/or the interface between an Ir surface and the thin Au film. We demonstrate how anomalously reactive thin Au films grown on an Ir surface are, and also compare the Au films with Ag films grown on Ir to test the validity/generality of our proposed s-band center model.

Oct 1, 2003

By I. Spector

A SHORTAGE of cement in the Prairie Provinces, together with an aggressive policy on the part of the Saskatchewan Government in bringing new industries to the province, combined to create a favourable set of conditions for the establishment of Saskatchewan's first cement plant on the outskirts of Regina. Built by Saskatchewan Cement Corporation Limited, this single-kiln plant, tl1e latest addition to cement producers on the Prairies, began operations in the Fall of 1956. Location of the plant followed the trend of building cement manufacturing facilities in market areas rather than at raw material sources. In 1957, all assets of the Corporation were taken over by Inland Cement Company Limited and the plant and quarry now operate as Saskatchewan Cement Company, an Inland division. The Regina plant's production makes up approximately eleven per cent of the productive capacity of all plants in the Prairie Provinces. At present, two types of cement are manufactured -normal portland and sulphate resisting.

Jan 1, 1960

By E. S. Moore

Introduction The geology of the Sudbury nickel field has been studied extensively, but there are few reports dealing with the structure of the interior of the basin. It was not until the Treadwell-Yukon zinc-lead deposits were discovered that attention was strongly directed toward the large-scale faulting that has split the basin parallel to its long axis. This faulting has been responsible for the , ore deposits in the basin and it may be regarded in many ways as the most important geological event, next to the intrusion and differentiation of the nickel eruptive sheet, that has occurred in the Sudbury region. The early reports on the nickel region by Bell, and Barlow, were chiefly concerned with the nickel-copper ores and with the formations of the region. Coleman was the first geologist to map the nickel eruptive as a continuous sheet around the belt and to emphasize its basin character. On the map accompanying his later report, he shows an important offset in the nickel eruptive at its southwest end, where the large fault cuts this portion of the basin, but the fault was not traced into its interior, as little detailed work was clone in the basin at that time. No ore-bodies had been developed outside of the nickel-copper deposits associated with the norite when the map was prepared, and attention was mostly concentrated on the nickel eruptive. Coleman did, however, map and name the various formations found within the basin and, in general, his delineation of these has remained the standard for prospectors and other workers in the field until the present day.

Jan 1, 1930

By H. Link

"The extremely low permeability of the water-carrying beds in the nevonian formation of the potash district of Saskatchewan does not permit the injection of cement or chemicals to seal off sufficient water from the shafts to guarantee the safety of the mine. Based on many years of experience with wet shafts in the German and French potash mining industry, Alwinsal Potash of Canada Ltd. decided to have their potash mine shaft near Lanigan, Sask., which was completed in September of 1967, lined by means of an absolutely watertight lining of combined concrete and steel-plate construction.This shaft lining, consisting of two steel shells of welded construction with concrete filled in between, has proved itself before in the German coal mining industry. It guarantees a permanently dry shaft. With this type of lining, time-robbing and very often abortive injections are superfluous and the regular repair and adjusting work as well as the corrosion of conveyances and ropes can be avoided. Above all, however, the danger of a water inrush into the shaft is abolished completely."

Jan 1, 1971

By P. G. Killeen

Proper calibration of portable gammaray spectrometers and spectrometric logging equipment is essential if they are to be used for accurate quantitative determinations of radioelement concentrations. In the case of both types of equipment, it is necessary to determine the system calibration constants (stripping factors and sensitivities). In the case of borehole logging equipment, it is further necessary to determine the system response characteristics if the data are to be computer processed to improve the accuracy and resolution of the logs. Facilities are now available near Ottawa for the complete calibration of portable gamma-ray spectrometers and spectrometric logging equipment, in addition to already existing facilities for calibrating airborne gamma-ray spectrometers. Limited additional facilities are also available or planned in several other areas of Canada.

Jan 1, 1978

By R. N. Chakravorty

Environmental monitoring plays a key role in coal mine safety. In recent years, significant advances have been made in the development of systems suitable for monitoring air in underground coal mines. Because of intensive mining and large capital outlay, the need for higher productivity consistent with safety is well recognized and it appears that environmental monitoring may help achieve this objective. This paper reviews the state-of- the-art in the monitoring technology with particular reference to hazardous gas detection in underground coal mines. The preliminary results obtained from ongoing studies, with regard to continuous monitoring of methane and carbon monoxide in mine air in some of the operations in Western Canada, are discussed. The inadequacies of the methods using spot samples are examined and the need to supplement the present practice with continuous monitoring systems is emphasized.

Jan 1, 1979