Search Documents

By G. Wilson

"Satisfactory hydraulic performance of a centrifugal slurry pump is not the only design criterion. If abrasive wear exists the severity of any damage can be reduced and the life of the wearing parts prolonged by selecting the correct pump to suit the conditions of service. This paper is concerned with the design and construction of centrifugal pumps for handling abrasive solids. The wear phenomena due to the slurry being pumped and the materials used to combat abrasive, wear are outlined. The hydraulic design of the impeller and casing and their relationship to wear and the hydraulic radial and axial unbalance are discussed. The prediction of abrasive wear in pumps can not be precise, as many factors are involved - and this is the object of current research."

Jan 1, 1973

By The Staff

THE property of McKenzie Red Lake Gold Mines, Limited, consists of eleven claims located on McKenzie island in Red lake. The mine is about 4,Y:l miles by water from the Howey townsite on the same lake, and about 95 miles north of Kenora, Ont. (see Figure 4). Mail and express are flown-in daily, winter and summer, from Sioux Lookout, Hudson, Kenora, and Winnipeg. All heavy supplies are freighted-in during the summer over a water route, using four marine railway portages, from Hudson, Ont., a distance of about 180 miles. During the winter, freighting over the same route is clone by tractor if necessary, but costs are three to four rimes the summer rate. Due to these conditions, large inventories of supplies must be kept on hand, varying from a spring minimum of $45,000 to a peak of $110,000 early in November. The average cost of all freight brought in from steel during 1937 was $0.01 per pound.

Jan 1, 1938

By R. W. Coburn

The results of field experiments on wells which required stimulation indicated that engineered well-completions will cause an increase in ultimate recovery at reduced costs. Techniques and tools have been developed which can be used to establish well conditions most conducive to successful stimulation. Cementing, perforating and treating are bound together so completely that the success of one phase is completely dependent on the .effectiveness of the preceding phase. A method of determining the efficiency or effectiveness of any given well-stimulation treatment has been derived. Pressure behaviour during a treatment can be analyzed to yield the total percentage of the formation which has been treated.

Jan 1, 1960

By T. G. Joseph, E. Lampard

ABSTRACT: Surface mining operations must manage variability from within their operations as well as variability imposed upon them by external forces. A framework to manage both internal and external variability through the continuous review and adjustment of a mine plan during active mining lifetime operation is introduced, to minimize lost production and maintain operational safety. The observational approach of “observe, evaluate, interpret, predict, and adapt” is employed as the backbone of this approach. Although written with a surface mining operation in mind, the framework outlined in this paper would be equally applicable to any mining or processing operation.

Jan 1, 2011

By T. Avilez, D. Salari

"The economics of developing gold deposits containing elevated levels of cyanide soluble base metals is often challenged by high cyanide consumption and increased operating costs. SART is a chemical process that enables cyanide consumed by base metals to be recovered and recycled for gold leaching. The process also provides concurrent recovery of the base metal to generate incremental revenue from the sale of high-grade base metal sulphide concentrates. Although SART was developed and successfully piloted by Lakefield Research and Teck Corporation in the late 90’s and is now a public domain technology, the adoption of SART has been relatively slow due to concerns about implementation costs and the reliability of metallurgical performance. Through extensive experience in selective metal sulphide precipitation applied to mining wastewater since 2007, BQE Water has provided process know-how, design along with operations and maintenance experience to a number of projects involving the integration of SART into various metallurgical flowsheets on an industrial scale. This paper presents the commissioning experience and operating data from a SART plant treating up to 500 m3/hr of leach solution at a heap leach operation in Mexico. INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes to the traditional gold extraction metallurgical flowsheet. A tool available to the industry to help manage the interference of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle."

Jan 1, 2018

By C. D. Rowe, H. S. Mitri, J. Malki, I. Vennes

Ore extraction at great depths creates high stresses around mine openings, which can result in violent rock failure in one of various forms of strainburst. This is especially true with strong and brittle rocks, which can store a large amount of strain energy that is suddenly released at failure. The strength and brittleness of rocks have been extensively investigated in the past. The most widely accepted method for the determination of rock burstability is the strain energy storage index obtained from a non-destructive uniaxial load–unload test. However, the results of this method are not always conclusive, showing less repeatability when the target test load is changed. This study concerns itself with the introduction of microscopic analysis as a tool to help validate the strain energy index results when burstability cannot be warranted based on mechanical property tests alone. In this study, two types of rocks, namely, basaltic komatiite (BK) and felsic norite (FNOR) obtained from Canadian underground mines are examined. The selection is based on the premise that felsic norite is known to be burstable from the mine experience, whereas basaltic komatiite is not necessarily burstable. A total of 60 mechanical properties tests were conducted including uniaxial compressive strength, Brazilian tensile strength, and load-unload tests. Laboratory tests on FNOR consistently exhibit high burstability; however, the results for the BK tests are not conclusive. To seek explanations for the mechanical rock behavior, 18 thin sections were examined with optical microscopy and image analysis. The findings show the tested BK specimens are dominated by alteration products, and all primary igneous minerals are lost. There is minor quartz, garnet, carbonate minerals, talc, and serpentine, which give the rock its ductile properties. The FNOR specimens are found to be relatively fresh and supported by a strong network of plagioclase with minor pyroxene, biotite, and secondary micas, explaining the higher stiffness. This study demonstrates how optical microscopy can complement mechanical property tests to evaluate burstability of rocks.

May 4, 2025

By J. Olson

"A model was developed to use near-infrared (NIR) analysis of pulverized ore samples to estimate the recoverable gold content for ores from the Barrick Cortez Hills underground mine. Current routing practices use a ratio of the cyanide soluble gold content and fire assayed gold (CN/FA) to classify ores as oxide or refractory. Prediction accuracy of the NIR model was equivalent to the CN/FA ratio. Prediction accuracy was improved by combining the CN/FA ratio and the NIR spectra. Bootstrap validation estimates the root-mean-square error to be 9.92% with an estimated r-squared value of 0.893. This model will allow more accurate estimates of the variability in recoverable gold content throughout this mine. These data will aid in building an improved geo-metallurgical model or in making better informed routing decisions during the production cycle.INTRODUCTION The contained gold of an ore available for cyanidation is often related to subtle variations in the mineralogy. It is difficult and expensive to collect enough mineralogical information in order to predict how the variable mineralogy will impact the metallurgical results and project economics throughout the life of the mine or mill. Near-infrared spectroscopy may be an effective tool to rapidly and inexpensively collect discrete, quantitative mineralogical data for minerals that contain transition metal oxides, metal sulfides with semi-conduction properties, rare earth metals, and some chemical groups having di-pole covalent bonds such as carbonates, sulfates, and various types of clays (Hunt, 1977). Near-infrared spectroscopy can be a powerful tool for geo-metallurgical characterization of deposits where the presence of these minerals has direct or indirect relationships to metallurgical results such as grindability, regent consumption, or recovery. Near infrared spectroscopy is a rapid analysis that measures the intensity of reflected light in the near-infrared spectrum. The ranges for the ASD-Panalytical units used in this study extend through the visible spectrum and into part of the UV spectrum, reporting reflection by wavelength from between 350 nm to 2500 nm. Absorption peaks visible in this range are a result of interactions with outer valence elections or chemical bonds. The location and intensity of the peaks vary depending on the chemical composition and crystal structure of a solid indicating the presence and abundance certain minerals (Hunt, 1977; Clark, 1984)."

Jan 1, 2017

By C P. Gravenor

In 1953, a deposit of sedimentary oolitic iron ore was discovered in the Clear Hills area of northwestern Alberta. Since that time, detailed drilling has outlined reserves in excess of 200 million tons of ore grading 30 to 35 per cent iron. Attempts to physically beneficiate the ore to meet blast furnace or direct reduction feed specifications have been, in general, unsuccessful. In 1960, Premier Steel Mills Limited and the Research Council of Alberta jointly sponsored a pilot-plant test at the R-N Corporation at Birmingham, Alabama. About 5,000 tons of ore were treated, and briquettes containing 90 per cent Fe were produced, with 83 per cent recovery. At the same time that the R-N tests were being made, the Research Council initiated a program to produce high-purity powders by chemical methods. Several purification techniques were investigated; hydrochloric acid dissolution of reduced ore was finally adopted. Briefly, the steps involved in this acid process are as follow

Jan 1, 1964

By H. Tsuruta, A. Fujibayashi, I. Sumi, A. Murao, R. Murai

Injection of biomass into blast furnace as alternative reducing agent is so effective for the purpose of mitigation of carbon dioxide emissions from steel industries, because biomass is considered to be carbon neutral raw materials. Certain amount of Palm Kernel Shell (PKS) is abandoned after Palm oil extraction process. To use as a reducing agent of blast furnace, PKS was carbonized and classified by 100 mesh sieve. To examine the gasification behavior of PKS carbide under the blast furnace conditions, several combustion experiments were conducted using hot model experimental furnace. The experimental results showed that the gasification efficiency of PKS carbide increased as the quantity of volatile matter increased. This tendency is the almost the same for the pulverized coal, so carbide of PKS can be used at blast furnace at appropriate amount of volatile matter that can be controlled by carbonization condition. In addition, the pressure drop of the furnace tends to decrease because the amount of ash in PKS carbide may be smaller than that of pulverized coal. PKS carbide is a suitable reducing agent in that respect.

Jan 1, 2015

By Jean Scott, G. A. Collins, G. W. Hodgson

WHILE it is well known that trace metals in crude •oils and distillates have been a matter of deep concern to refining engineers because of the damage done .by the metals to cracking catalysts and refractories (8, 5), the trace metals in crude oils may be of great benefit in correlation studies and in origin studies. During the geological processes in which the oil is formed from •animal and vegetable life, the hydrocarbons are subjected to a host of inter-related reactions, both physical and chemical. It has been well demonstrated that the lighter materials, certainly the short-chain paraffin hydrocarbons, are degradation products of the heavier molecules, and it might be concluded that for correlation studies it would be advisable to direct attention as much as possible not to the degradation products of the large molecules but to the large molecules themselves. Be this as it may, the methods at •hand to conduct the study are not particularly precise and, in the past, attention has centred on the simpler small molecules, as evidenced by the great mass of work involving distillation and chromatography with painstaking separation of the simpler 'front-end' hydrocarbons.

Jan 1, 1954

By B. Zeifert, C. Martínez-Morales, A. Romero-Serrano, A. Pineda-Rivera, H. Martínez-Gutiérrez, G. Diaz-Sandi

In this work, the effects of CaO/SiO2 ratio and the FeSO4 and FeS2 contents on the stability of the mineralogical species in chromium-based slags were studied. The chemical stability was evaluated by leaching with an acid solution. The main Cr-compounds in slags with FeSO4 and CaO/SiO2=1 were FeCr2O4 and Ca3Cr2Si3O12, while Cr3S4 predominated in slags with FeS2. The slags with CaO/SiO2=2 mainly contained CaCr2O4. The highest Cr concentration levels in the leaching liquors corresponded to slags with CaO/SiO2= 2, and the lowest Cr concentration corresponded to slags with high FeSO4 or FeS2, owing to the stable binding of chromium in the compounds FeCr2O4, Cr3S4 and FeS•Cr2O3.

Jan 1, 2011

By F. P. Morawski, J. E. Schelske, J. R. Geddes, B. R. Eberts, D. M. Wilson, J. D. Jeffries

"The Griffith Mine is located 200 miles northeast of Winnipeg and is 30 miles south of Red Lake, Ontario. Owned by The Steel Company of Canada Limited and managed by Pickands Mather & Co., it has an annual rated capacity of 1.5 million tons of high-grade iron ore pellets with an analysis of 66.3 per cent iron and 4.5 per cent silica.Development of the mine and construction of the plant got underway in January of 1966 and operations began in February of 1968. The orebodies outcrop on the shore of Bruce lake and run under the lake. The ore in its crude form is a metasedimentary low-grade magnetite and occurs in a highly folded banded formation. The average iron analysis of the crude is 29 per cent and the over-all weight recovery is 32 per cent.In order to mine the portion of the orebody under the lake, the soft varved clay on the lake bottom was hydraulically dredged and a dyke constructed of rock, with till used to provide an impervious seal on the lake side of the dyke, prior to dewatering.Mining is carried out by conventional open-pit tech-niques. Ore dressing is achieved by combining one crushing stage and a two-stage grinding system, with beneficiation by magnetic separation, hydroseparation and flotation. Agglomerating is done with conventional balling drums and pelletizing is carried out in shaft furnaces.Of interest and discussed in detail are the 32-foot autogenous cascade mills ."

Jan 1, 1970

By A. Giacomini, M. Nazem, E. Fathi Salmi

"Numerical simulation of collapse of tunnels in weak rocks is one of the challenging problems in rock mechanics. Collapse can impose technical and financial difficulties during the construction of underground excavations. This phenomenon, particularly in shallow excavations, may lead to propagation of a caved zone toward the surface and formation of chimney subsidence. Chimney subsidence has numerous catastrophic consequences such as the adverse environmental impacts and damage to surface structures in vicinity of excavations. Due to the importance of subsidence in civil engineering, the main goal of this study is to propose an appropriate method for preventing the formation of subsidence in shallow tunnels in weak rocks. The Dolaei road tunnel is investigated as a case study, where a large chimney subsidence has occurred. The geology of the area and the geostructural characteristics of the rock mass surrounding the tunnel are briefly reviewed in this paper. Two-dimensional as well as threedimensional numerical simulations are conducted to study the tunnel stability. Moreover, the effects of staged excavation and pre-supporting method on controlling the ground movements are studied. Outcomes of this study indicate that employing forepoling and staged excavation can be a practical remedy to control the ground movements and prevent the formation of chimney subsidence.INTRODUCTIONPredicting the formation of subsidence, mainly sinkhole subsidence over civil or mining excavations, is a very challenging task. An accurate prediction of subsidence is required for selecting an appropriate control and mitigation system to reduce the level of ground movements and its impact on the surface life (Bétournay et al. 1994; Leca and New 2007). Excavations, particularly in weak grounds, could result in surface subsidence; they modify the in-situ stress conditions as well as the hydrogeology of the area. Construction of unsupported excavations in soft soils and relatively weak rocks usually leads to the formation of a failure zone behind the face. In a very soft ground, the failure zone can extend towards the ground ahead of the tunnel face. Propagation of this zone toward the ground surface results in generation of sinkholes."

Jan 1, 2015

By W. M. Goodwin

"IntroductionIN THE preceding paper we have learned about Canada's resources of metallurgical coal. There is an adequate amount in Nova Scotia, a very large reserve on the eastern flank of the Rocky mountains, and a strictly limited supply on the Pacific coast. Added to these is an unknown quantity of coking coal in the Peace River district, at present rather isolated but possibly capable of industrial development in the future.The chief use of metallurgical coal is to make iron and steel. For this, an adequate supply of iron ore is required. So we should now scan the Canadian supply of iron ore, the possibility of its increasing use at home, and the probable markets abroad.Trade in iron ore tends to be international, as is the case with many other raw materials. The present tendency with iron and steel, in contrast, is to keep its manufacture within national boundaries, and there is no evidence that this will change much in the years to come. We should keep these two points clearly in mind when considering the disposal of iron ore from Canadian mines. We should remember, also, that the modern blast furnace and steel plant has such a large output that a correspondingly large population, reasonably compact, is needed to consume its products.Large Ore Supply in East, Small in WestCanada has now four major iron ore fields, well situated to serve adequately the eastern half of the country. Wabana .and Labrador are well placed to serve overseas markets and plants on the eastern seaboard and eastern interior of the United States and Canada."

Jan 1, 1952

By B. Westin, G. Voicu, C. Daoust

Orogenic gold deposits represent a major class of deposits that are found in various rock types of various ages. Those deposits show a strong structural control that usually complicates their interpretation at the regional and deposit scales. The Rosebel Gold district located in Surinam (South America) is hosted in a Paleoproterozoic greenstone belt of the Guiana Shield, and has been recently classified as one of those orogenic gold deposits. The gold district comprises eight distinct deposits located along three different structural trends and within different rock types. The mineralization is undefonned and shows a strong structural control characteristic of orogenic gold deposits. All the deposits of the Rosebel Gold district have been subject to a detailed structural analysis that has led to the elaboration of a new structural model for the whole gold district, which is now differing considerably from the previous models. This characterization had direct implications at three different scales. 1- While the older models were considering some areas of the property as gold-barren, the new structural model has led to recent exploration campaigns which have revealed positive results. 2- At the deposit scale, the comprehension of the various vein systems and of the folding of the host rocks has helped the establishment of optimized drilling campaigns. 3- At the mining scale, the comprehension of the architecture of the veins helps for the elaboration of optimized mining method. This study thus shows that the structural analysis of orogenic gold deposits is critical, and should be a priority for exploration and production in any mine.

Jan 1, 2011

By B. J. Keating

"AT PRESENT, it is not certain that any of the sulphide de in the Province of Nova Scotia attain the lower grade limit of 60 per cent sulphides over the minimum area of 1,000 square feet suggested as cut-off specifications for inclusion in this Symposium. However, several of them do include massive sections of substantial size and others represent concentrations of sulphide material that are well above average. It is felt, therefore, that a tentative classification of the deposits and presentation of their geological settings are justified and may help round out the genetic aspects of this study. Accordingly, data considered to be the most pertinent are assembled here in the event that some may fit into larger-scale patterns of mineralization that may take shape as a result of this investigation.The three principal massive sulphide deposits in Nova Scotia are the Stirling, the Smithfield, and the Walton. The locations of these are shown on the accompanying key-map (Figure 1).Three other deposits, the locations of which are also indicated on the map, are the Meat Cove, Rocky Brook, and Gays River de¬posits. Although these fall far short of the minimum dimensions and grade specifications referred to above they are singled out because they have received more than passing attention and are illustrative of the mineralization types to which they belong."

Jan 1, 1960

By Youjun Tao

Falcon centrifugal gravity separation tests were conducted to study desulfurization and de-ashing performance with different size fractions of a high-sulfur Chinese -0.5mm fine coal in a dense medium. Performance indicators such as combustible recovery, ash and sulfur rejection, and desulfurization efficiency were used to evaluate the separation efficiency. The results show that for -0.5 mm coal particles, all performance indicators except ash rejection are higher for the Falcon concentrator than for flotation. More specifically, for the +0.125 mm size fraction, Falcon centrifugal separation produced better ash and sulfur rejection performance than froth flotation. However, the Falcon concentrator also showed higher combustible recovery but lower ash and sulfur rejection than froth flotation for the -0.125 mm size fraction.

Aug 1, 2013

By R. E. MacAfee

THERE have been great changes in the design, capacity, and pressure of steam generating units over the past fifty years. If we go back as far as 1890, the plants then existing were largely horizontal return tubular boilers, hand-fired, with the boilers supported on the brick sitting which was com-posed of red brick with, probably, a refractory lining one brick thick in the combustion chamber. About this time, the water tube boiler began to supplant the H.R.T. boiler and, where new plants were being constructed of any size, water tube boilers were largely installed. In those days, say from 1890 to 1905, a 250 h. p. water tube boiler was considered a large unit. These boilers were largely the straight tube type and were set with the first row of boiler tubes three to six feet above the grates. The brick setting was a combination of red brick and fire-brick. The fire-brick lining in the furnace proper was usually 9 in. thick and in the first pass 4 1/2 in., while the rest of the setting was entirely red brick. These units were largely hand-fired and were expected to produce about 100 per cent rating as a maximum. It may be well at this point to define rating, which is the evaporation of one boiler horse power per hour by each ten square feet of heating surface in the boiler. A boiler horse power is the evaporation of 34.5 pounds of steam from and at 212°F. Consequently, a boiler containing 2,000 square feet of heating surface is rated at 200 h. p. and the evaporation at 100 per cent rating is 200 X 34.5, which equals 6,900 pounds of steam per hour from and at 212°F.

Jan 1, 1939

By M. C. Walton, W. Roelofs

ABSTRACT: In most cases, a refractory repair involves dealing with used refractory linings above shoulder height, defining these as overhead refractories. This paper details a method of personnel protection involving a low-pressure inflatable balloon system, installed to prevent the dislodgement and freefall of in-situ refractories. This system has been successfully applied to numerous types of vessels in the process industries in the last three to four years. This paper, prepared for the CIM Conference of Metallurgists held in Vancouver, British Columbia in October 2010, outlines details of the system and gives examples of successful applications.

Jan 1, 2012

By A. Monballiu, J. A. Martens, Y. W. Chiang, A. Van Audenaerde, R. M. Santos, T. Van Gerven, B. Meesschaert

In this work, bioleaching of non-sulphidic materials by applying chemoheterotrophic bacteria and fungi is studied. It was found that the tested fungus, Aspergillus niger, leached substantially more nickel from olivine than the tested bacterium, Bacillus mucilaginosus. A. niger also outperformed fungal species Humicola grisae and Penicillium chrysogenum in the leaching of olivine. Contrary to traditional acid leaching, the microorganisms leached nickel preferentially over magnesium and iron. On average, a selectivity factor of 2.2 was achieved for nickel compared to iron. This can potentially facilitate postprocessing of the leach liquor and reduce the cost. The impact of ultrasonic conditioning on bioleaching was also tested, and substantial increase in nickel extraction with A. niger was observed. This was credited to an increase in the fungal growth rate, the promotion of particle degradation, and the detachment of the stagnant biofilm around the particles. Furthermore, ultrasonic conditioning enhanced the selectivity of A. niger for nickel, resulting in a selectivity ratio for Ni/Fe equal to 3.5. The chemical resistance of the selected microorganisms to several heavy metal and metalloid (As(III,V), Cd, Cr(III,V), Ni, Pb, Zn) was evaluated. It was found that, with the exception of As(v) and Cd, A. niger has high tolerance to these components. Therefore, this biohydrometallurgical route can potentially be applied to non-sulphidic wastederived materials, such as industrial slags, ashes and sludges.

Jan 1, 2014