Search Documents

By Kallioinen Jouko

"Advanced Flotation Technology is the application driven design of Don-Oliver flotation cells to achieve the optimum performance for each type and grind of flotation. Optimum performance is the combination of both recovery and selectivity.Optimized performance is the combined product of optimized mixing and effective froth removal. Optimized mixing is applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Effective mixing for fine material is easy, but overmixing reduces selectivity in frothbed.Selectivity in flotation is an important target, especially when treating complex ores, and parameters in frothbed have been examined to improve the separation of minerals and eliminate circumstances that reduce separation rate.Advances in process control have been achieved with expert controls and instructive operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed to be used in future process development work. Excellent results of this Advanced Flotation Technology have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified."

Jan 1, 2000

By Rudy Tenbergen, Dick Farmery, Jim Naylor

"Paste backfill has replaced cemented rock fill as one of the components to improve ground · control and mine safety at the Macassa Operation of Kinross Gold Corporation in Kirkland Lake, Ontario. It is the first operation to utilize "" flash thickening ""of very fine gold tailings to a paste consistency in the ""Paste Production and Storage Mechanism"", a joint technical development of Inco and GL&V. The tailings paste is mixed with alluvial sand to produce an engineered quality paste backfill. The development leading up to the decision to proceed with this novel technology is discussed, as well as commissioning of the backfill operation.IntroductionThe occurrence of a major rockburst on November 23, 1993 prompted a review of mining and backfill procedures at the Macassa No 3 shaft . This shaft is some 7238 ft deep and lies in a mining belt that is prone to seismic events. The recommendations were to change the mining from underhand cut and fill to mechanized long hole stopping and to look at alternatives to the rockfill backfill system in place. The Macassa cemented rock backfill operation, while producing the desired fill stiffness had drawbacks as compared to paste fill. With paste fill, placement rates are faster, more openings can be filled, it is less expensive and less prone to the occurrences of compensable incidents.Macassa mining personnel visited the Sudbury operations of Inco in 1993, where development on paste backfill was in progress. As some of the R&D was taking place with funding from the Premier's Council Technology Fund of the Ministry of Trade and Technology of the Province of Ontario , Inco personnel at that time did some feasibility and conceptual consulting on the use of paste fill for the industry. Inco had developed the use of alluvial sand paste fill, an engineered blend of alluvial sand and tailings fines and was doing development work to eliminate the ""conventional"" way of producing paste from mill tailing by thickening and filtration. This latter development work was taking place with GL&V Ontario. That work led to the filing of a joint Inca/ GL&V patent application for the PPSM, the Paste Production and Storage Mechanism with all marketing rights being held by GL&V."

Jan 1, 1997

By Norman O. Lotter, Dominic Fragomeni, Lori J. Kormos, Guy Comeau, Antonio Di Feo

"A performance opportunity was identified for the Raglan concentrator operation by changing the selection of xanthate from Potassium Amyl Xanthate (PAX) to Potassium Isobutyl Xanthate (PIBX). This opportunity was identified by a Statistical Benchmark Survey of the operation and QEMSCAN measurement of these survey samples, in which fine liberated pentlandite was found in the final tailings. This was confirmed by some laboratory scale flotation testwork using High- Confidence Flotation Testing. A statistically designed plant trial was implemented in 2007 to measure and confirm the performance gain. This trial design used on-off switching following a three-month reference distribution of normal operations using PAX. This layout provided both external and internal reference distributions on PAX to be established. These were used to evaluate the internal reference distributions on PIBX. This trial format was deliberately designed so as to block out the effects of autocorrelation in the operations data. In this way, small but significant metal recovery gains may be measured and proven in a plant trial. The paper describes the case study to show that this approach successfully blocks out autocorrelation in time, which is an obstacle in analysing concentrator operations data. The results showed that the PIBX had produced clear and statistically significant recovery gains for Ni, Cu, Pt and Pd. Adjusted for feed and concentrate grades, these recovery gains were: Ni: 1.00, Cu: 0.96, Pt: 5.07 and Pd: 1.90%.INTRODUCTIONConcentrator OperationsMilling and flotation, sometimes accompanied by gravity separation, are well-established unit processes. These have traditionally been used to treat ore that has been mined, producing a lowbulk concentrate containing a high percentage of the paymetal(s) in the ore mined. These concentrates are more economically treated in subsequent beneficiation processes than the ore from which they were produced.This choice of a concentration process results in a significant and variable paymetal loss to the concentrator tailing. This tailing is discarded and disposed of in an impoundment area, and has no immediate business use. This paymetal loss forms the largest loss of paymetal in the entire flowsheet by which refined, or saleable, metal(s) are produced [Cramer, 2001]. The question arises as to whether any particular concentrator is performing at its full potential, and how this answer may be determined. In a concentrator operation, there is always an ongoing performance improvement programme for this reason."

Jan 1, 2009

By Dan Alexander, Ivan Crnkovic, Sarah Schwarz

"Several plant studies have been conducted at the Zinifex Century Mine over the past 5 years. For each of the plant studies, surveys of the zinc primary circuit were conducted, characterisation measurements for each operating cell taken, and the floatability components of the ore mapped to develop a model of the circuit. The floatability components and machine parameters were then used to simulate changes in circuit configuration and operating conditions, enabling further potential improvements in circuit performance to be identified.This paper reviews the current flotation practice at the mine, as well as various circuit changes and developments implemented by site. The application of the methodology and the evolution of the standard procedure are also discussed.INTRODUCTIONBase metals were first discovered in the Lawn Hill region of Queensland’s North West in 1869 and the first mining lease in this area was pegged in 1887 over what is now known as the Silver King vein deposit. The area encompassing these veins, which includes the Century deposit, was proclaimed the Burketown Mining Field in 1899. Exploration titles were granted to CRA in 1987, precisely 100 years after the initial discovery at Silver King, hence the name ‘Century’.Century was commissioned by Pasminco in late 1999, with the mine becoming fully operational on 1 March 2000 and the official opening taking place in April. Pasminco had bought the Century and Dugald River deposits from CRA in 1997 for A$345 million, and invested some A$710 million in bringing Century into production. Today, Century is the world’s second-largest zinc mine in terms of its output, having reached full capacity in 2003.The Zinifex Century Limited (“ZCL”) lead-zinc-silver deposit is located approximately 250 kms north-north west of Mt Isa in north-western Queensland. The deposit is a large flat-lying ore body covering an area of some 1.2 by 1.4 km, the 45 m-thick stratabound sulphide orebody is hosted within an 850 m-thick sequence of Proterozoic siltstone, shales and sandstone, amenable to open-cut mining methods. The mine has ramped up to full production delivering five and a half million tonnes of ore per annum, yielding approximately 900,000 tonnes of zinc concentrate and 90,000 tonnes of lead concentrate. Mine life is expected to be about 8 years"

Jan 1, 2008

By B. G. Cousins, L. Racine, R. S. MacPhail

"FLEX 31 is a chemically enhanced sodium isopropyl xanthate that has shown improved collection properties over SIPX for copper-bearing and copper-activated minerals. Characteristics such as improvement of recoveries with lower dosages and high pyrite and pyrrhotite rejection capabilities have all been exhibited by FLEX 31.The most improved results have been seen insphalerite flotation. Plant trial work carried out in the zinc circuit at the Louvicourt Concentratorin northern Quebec has produced data showing superior grade and recoveries from rougher concentrates that previously had not been attain-able with other reagents effectively. The improvement over SIPX adds up to an almost$1,000,000 annual improvement on the mine’s bottom line at present zinc prices.IntroductionSodium Isopropyl Xanthate (SIPX) is one of the most popular flotation chemicals on the market today. Somewhat more specific than amyl xanthates, SIPX is used in a variety of ores like copper/zinc, lead/zinc, arsenopyrite/pyrite, and many others (Melis et al., 1991). An investigation carried out by Tennants Research Technology Applications (TRTA), a division of Charles Tennant & Co. (Canada) Ltd., produced a chemically enhanced SIPX that has shown all the advantages of normal SIPX along with improved recoveries of copper and copper activated minerals. The new product has been named FLEX 31. Currently, FLEX 31 is manufactured at the Prospec Chemicals, another division of Charles Tennant & Co. (Canada) Ltd.A large amount of laboratory testing pro-grams have been carried out with FLEX 31 todate (MacPhail and Cousins, 1995; Cousins and MacPhail, 1996). One of the minerals that has a defnite affinity to improved fotation is sphalerite (ZnS). Once activated with copper sulphate, sphalerite has produced some of the most spectacular test work when FLEX 31 is compared directly to SIPX. Plant trials of FLEX31 at Aur Louvicourt Inc. carried out in 1995show that FLEX 31 is far superior to SIPX for activated sphalerite flotation."

Jan 1, 1997

By Alexandra Kozak, Rodrigo Costa, Bob Fukuhara

"The Jacobina project in Bahia, Brazil commenced operations in 2004 with a design capacity of 4,200 tpd. A project development plan to increase plant capacity to 6,500 tpd will be discussed. The project included an evaluation of the existing circuit and addressed bottlenecks in the crushing, milling, sedimentation, leaching and tailings transport. These circuits and the methodology used to provide higher capacity will be presented.INTRODUCTIONThe Jacobina mine is located in the state of Bahia in northeastern Brazil approximately 330 km northwest of the state capital city of Salvador and 9 km from the town of Jacobina. The Jacobina Mine (Figure 1) is owned by Jacobina Mineração e Comércio, a wholly owned subsidiary of Yamana Gold Inc.The gold mineralization of the Jacobina mine is hosted within quartz pebble conglomerate reefs of the Serra do Córrego Formation which together with the Rio do Ouro Formation forms the Serra do Jacobina mountain chain.The Serra do Jacobina mountains have been mined for gold since the late 17th century. Since the 1970’s, the Jacobina mine has been operated by Anglo American, Williams Resources Inc., Desert Sun Mining Inc. The mine is currently owned by Yamana Gold Inc.In December of 1998, operations at Jacobina were suspended and the property was placed under care and maintenance. Desert Sun Mining Inc. began exploring the property in 2002 and eventually purchased the Jacobina mine in 2003. In 2003, a feasibility study was completed that evaluated the economics of re-developing the mining operations and expanding gold production. In 2004, refurbishment and re-development of the mining operations began and the milling facility throughput capacity was expanded from 1.08 to 1.512 Mtpy (3,000 to 4,200 tpd). The milling operations were commissioned in the 1st quarter of 2005 and commercial production was declared 1 July 2005. In April 2006, Yamana Gold Inc. acquired the Jacobina mine through its acquisition of Desert Sun Mining Inc."

Jan 1, 2008

By François Robert

"The Eastern Abitibi Sub province (Quebec segment), contains two main types of gold deposits: the common quartz-vein type and the rare pyritic type. Both occur in areas dominated by volcanic rocks and are spatially associated with major fault zones.Quartz-vein gold deposits consist of simple to complex networks of quartz-carbonate-pyrite veins in reverse shear zones and extensional fractures. They occur in areas dominated by mafic volcanic rocks and are commonly associated with small syn- to late-tectonic porphyritic felsic intrusions. Associated alteration, which postdates peak metamorphism, is dominated by carbonatization, sericitization and pyritization of the wallrocks. These deposits formed late in the geologicalevolution of the Abitibi.Pyritic gold deposits range from deformed massive sulphide lenses to zones of syntectonic pyrite-rich veinlets and associated pyrite disseminations. These deposits occur in environments dominated by felsic volcanic rocks that are typically converted to sericite schists near the deposits. The associated pre-metamorphic aluminous alteration is now characterized by metamorphic sericite, andalusite, kyanite and chloritoid, overprinted by a late retrogression of alumino- silicates. These deposits probably represent deformed volcanogenic massive sulphide deposits, but the timing of gold introduction in these is not fully understood.The differences in geological attributes reflect significant differences in the genesis these deposits: the pyritic deposits probably have a multistage genesis, including a pre-tectonic stage, in contrast to a single stage late-tectonic genesis for the quartz-vein deposits.RESUMELa partie Est de la Sous-Province de l’Abitibi( segment québécois) renferme deux types de gites d' or: ceux de type ""veine de quartz"" et ceux, plus rares, de type ""pyriteux"". Ces deux types se trouvent dans des secteurs particulièrement riches en roches volcaniques et mantrent une association spatiale avec des zones de failles majeures.Les gites de type ""veine de quartz"" correspondent à des réseaux de complexité variable de veines de quartz-carbonate-pyrite se développant dans des zones de cisaillement inverse et des fractures de tension. Ils se concentrent dans les régions dominées par des roches volcaniques mafiques et s’associent fréquemment à de petites intrusions porphyriques felsiques syn- a tardi-tectoniques. L’altération associée ace type de glte est postérieure à la phase majeure du métamorphisme et consiste en une carbonatisation, une sericitisation et une pyritisation des épontes. La mise en place de ces gites est tardive par rapport à l'évolution géologique de l'Abitibi.Les gites d' or de type pyriteux consistent en des lentilles de sulfures massifs déformes, des zones d' abondantes veinules pyrite uses syntectoniques, et des zones de pyrite disséminée. Ces gites se retrouvent dans des empilements contenant surtout des roches volcaniques felsiques qui sont transformées en schiste à séricine pres des gisements. L’altération a l’umineuse pre-metamorphique associée a ce type de glte a donné naissance, lors du metamorphisme regional, a la sericite, a 'andal ousite, a Ia lcyanite et au chloritoi""de; par la suite, les alumino-silicates ont été affectes par une alteration retrograde tardive. Ces gites representent probablement des depOts de sulfures massifs volcan gènes déformes, mais la chronologie de la mise en place de l'or dans ceux-ci est encore mal comprise.Les caractéristiques géologiques propres à chacun de ces types de gites reflètent des conditions de formation différentes: le type ""pyriteux"" montre une histoire génétique polyphasée, incluant une étape pre-tectonique alors que le type ""veine de quartz"" s’est développe au cours d’une seule phase tardi-tectonique."

Jan 1, 1990

By Martin Plante, Denis Hamel, Marie-Pier Bédard, Jeff McLaughlin

"The results and methodology for the optimisation of the zinc flotation circuit at the Matagami Mill using the 6-Sigma methodology are shown in detail while only the base line and final results are presented for the copper circuit. As a result of the six sigma project, the zinc concentrate grade was improved by 2% and the zinc recovery by 3%, with reduced dosage of reagents while the copper concentrate was improved by 2.4%. The process variation in the zinc concentrate grade and recovery was also reduced by over 50%. The main factors contributing to the project success were identified to be improvement in the plant measurement systems, an internal benchmarking exercise and statistically designed laboratory and in plant tests to guide the process improvement. The annual value to Noranda resulting from this project has been estimated at approximately $5 million.INTRODUCTIONThe Matagami concentrator started ore processing from the new Bell- Allard deposit in July 1999. Concentrator performance (grade and recovery of zinc and copper concentrates) was highly variable and work was ongoing to fix the sources of variation. In the mean time, Noranda embarked on its 6-Sigma initiative across the company. The 6-Sigma DMAIC (Define, Measure, Analyse, Improve, Control) methodology was used in the two flotation circuits to reduce variation and improve performance. The statistical 6-Sigma methodology moves towards identifying and controlling critical process operating variables (the X' s) to achieve customerspecified performance (the Y's). The goal of the methodology is to describe a process in a numerical equation known as the transfer function, given as Y = f (XI, X2, X3.. .), where Y could be concentrate grade or recovery and examples of X's are reagent dosage, particle size, etc. With the transfer function, optimal operating conditions and control tolerances are established for the key X's to ensure the desired Y performance is obtained.Each phase of the 6-Sigma methodology is explained below with examples from the Matagami project."

Jan 1, 2001

By Mike Samuels, John Starkey

"This paper examines test results and grinding mill design for the recent Fortune Minerals’ NICO Project, located in the Northwest Territories. SAG milling and rod milling options are compared. Rod milling is clearly shown to be the best option because of the ore’s extreme resistance to breakage in a SAG mill environment.Surprisingly, the Bond Ball Mill Wi was 13 kWh/t for this ore. The Bond Rod Mill Wi was 20 kWh/t, whereas the SAG pinion energy to grind the ore to T80 1.7 mm was 30 kWh/t. The existence of ore with this ratio of SAG hardness to Bond BM Wi has not been previously observed. If not considered, this critical relationship may adversely impact the accuracy of mill design. This paper substantiates the significance of these findings to achieve successful grinding design on ore that is macro-competent during primary size reduction, but relatively normal during secondary grinding.INTRODUCTIONThe NICO Cobalt-Gold-Bismuth-Copper deposit is located 160 km northwest of the City of Yellowknife, Northwest Territories. It is the largest IOCG-type deposit (aka Olympic Dam-type) currently recognized in Canada with Mineral Reserves of 21.8 million tonnes contained within a larger 57 million tonne, lower-grade Mineral Resource. The project, owned 100% by Fortune Minerals Limited, has been assessed in a positive definitive feasibility study, subject to underground test mining and pilot plant testing, and is now in the permitting stage to develop a combined open pit and underground mine and process plant. An updated process flow sheet incorporates conventional crushing, grinding and bulk flotation, followed by filtration for shipment of a concentrate to a purpose-built refinery proposed to be built near Saskatoon, Saskatchewan. At the refinery, separate bismuth and cobalt concentrates will be produced following regrinding. The hydrometallurgical process methods include: pressure acid leach, precipitation, ion exchange, and electro-winning for recovery of cobalt as 99.8% cathode; solvent extraction and electro-winning of by-product copper cathode; ferric chloride leach and electro-winning for recovery of bismuth as 99.5% cathode; and cyanidation of the leach residues for recovery of gold as doré."

Jan 1, 2010

By Norman O. Lotter, Simon Yu, Tony Deng, Antonio Di Feo

"Xstrata Nickel’s Raglan operation, northern Québec, achieved paymetal recovery gains in 2007 by switching the collector from potassium amyl xanthate to sodium isobutyl xanthate. To follow on from that position, Xstrata Process Support (XPS) and A. Di Feo of Raglan proposed that a mixed xanthate system be formulated and tested towards further performance gains. This work selected ethyl and isobutyl xanthates as the candidates. An optimized ratio of these was to be determined by a designed experiment. This suggestion was based on an abundance of published literature that reported mixed collector systems outperformed single ones. A partial factorial design was used to configure four test conditions and a mid-square for the flotation work. The testwork was conducted using High Confidence Flotation Testing. The raw data were analyzed and modelled by Design-Expert software. An optimum ratio of 1.6:1.0 by mass (1.32:1.0 in molar terms) of isobutyl:ethyl xanthate was determined. Without this modelling, the optimum ratio would have been missed. Results obtained with the new baseline flotation test using this optimized mixture showed a 3.3% Ni recovery gain in the bypass concentrate and more than 1% recovery gain for PGM over the single PIBX system. This system has been proposed for and accepted as a plant scale trial in the first half of 2010.INTRODUCTIONConcentrator OperationsMilling and flotation of sulphide ores ahead of smelting and refining is a common practice. This choice results in the larger and more variable paymetal loss in the production of saleable metal [Cramer, 2001]. For this reason, it is common to see an ongoing performance improvement programme at the operations level. When successfully performed, these e"

Jan 1, 2010

By Jessica Egan, Daniel Hodouin, Claude Bazin

"The recovery of gold by leaching is influenced by the size of the gold carrier particles and the chemical environment. Using the relationships between the leaching rate, infinite recovery and particle size for a given set of chemical conditions, it is possible to simulate gold recovery for various feed size distributions. However the use of these particle size relationships is only valid if the leaching of gold from a given size class is independent of the production history of this size class. For instance, to use these relationships it is necessary to verify that gold recovery from the leaching of the 200-270 mesh size class remains the same if the size fraction is taken from a coarse or finely ground ore sample. Several laboratory tests were carried out to answer that question. Results of the tests show that within the large error margin associated to gold content measurements, the history of the production of a size class does not affect the gold leaching from that size class. Emphasis of the discussion is put on the difficulty associated with the processing of data containing significant measurement errors as it is the case for gold assays of leaching tests.INTRODUCTIONMore than 75% of the gold produced in the world is extracted by cyanide leaching of gold ores. The ore is ground to expose the gold carriers and the ground material is reacted in an oxygenated cyanide solution that dissolves gold, leaving solids gangue minerals that are disposed to tailings ponds or returned in underground mines as paste fill. The gold contained in the solution is recovered by either the carbon in pulp process or by cementation onto zinc powder, before being melted and casted into a brick (Marsden and House, 2006)."

Jan 1, 2009

By J. Lee, M. Peart, T. Bhambhani, D. R. Nagaraj, P. Riccio

"Over the past decade or so, our efforts have focused on developing the rationale and concepts for new technology in reagent development and optimization in the processing of base and precious metals. A major outcome of these efforts have been the development of a novel family of collectors, principally driven by the MAXGOLD® and Aero XD-5002® chemistries, for precious metals recovery from primary Au ores and Cu-Au ores. These chemistries was developed to be robust to address the complex mineralogy and gold deportment in these ores. Plant trial data for a variety of ores have confirmed that the both Aero® XD-5002 and MAXGOLD® chemistry are indeed versatile in recovering gold values occurring as gold alloys and/or associated with many types of sulfides, and in altering the deportment of certain sulfides (such as those bearing As, Bi etc). An overview will be given in this paper using plant data to highlight the application of these reagents.INTRODUCTIONThe subject matter of this paper is the flotation of Au containing minerals from their ores. The motivation from this manuscript comes from the several challenges faced with the processing of Au ores, as was articulated in detail by Nagaraj (2008). The biggest challenge is the complex mineralogy; most easy-to-treat free-milling ores bodies are largely depleted. The Au values are distributed in multiple host minerals such as pyrite, pyrrhotite, arsenopyrite and Cu minerals such as chalcopyrite. Au values also happen to be finely disseminated within the various minerals and are sometimes invisible in optical microscopy. Additionally, on any given day, some mines treat multiple ore types, and the mineralogy is different for each ore type.Xanthates continue to be the collectors of choice at most Au and PGM operations around the world. Most primary Au operations tend to consume very large amounts of collectors; the dosage ranges anywhere between 40-400 g/t and this has been attributed to both mineralogical and non-mineralogical factors (non-mineralogical factors include the low cost of xanthates and the mindset that “more is always better”, which is not necessarily the case). In addition, several studies now show that xanthates alone are never sufficient where multiple value minerals are present, and that supplementary collectors are required. The large doses present a substantial cost to the minerals industry, and many mining companies have expressed the need for more efficient reagents that can improve metallurgical performance at low dosages."

Jan 1, 2013

By G. Couture, J. -F. Dubé, F. Letarte-Lavoie

"The Xstrata Nickel Raglan concentrator, located in Quebec’s Nunavik region, has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high-grade nickel ore, the plant’s current capacity is 1.3 million tonnes per year due to various optimization projects. In 2011 and 2012, the Metallurgical group, with assistance from BBA, updated and optimized the variables affecting SAG throughput in order to optimize process stability while maintaining maximum plant throughput. This project consisted of reviewing the control strategy and completely updating the pre-existing Fuzzy Logic controller. This paper describes the successful update of the controller including a complete revision of control rules, a new process control strategy and the integration of new process variables, most notably mill rotational speed. It will also show how this new approach has provided a simple and robust way of delivering both an increase in throughput while reducing process variability.INTRODUCTIONThe Xstrata Nickel Raglan Mine concentrator is located in Northern Quebec along the 62th parallel. It has been in operation since 1997 and was originally designed to treat 800,000 tonnes of ore annually. The Raglan Agreement held with the Makivik Corporation and the Inuit communities limits the annual tonnage of ore that can be processed at 1.32 million tonnes.The ore is processed in a 24 foot variable speed, semi-autogenous grinding mill (SAG). The conversion from Autogenous Grinding (AG) to SAG was completed in 2006. Before the ore is processed by the SAG, its size is analyzed by a Wipfrag camera that provides a granulometry estimate. A cone crusher reduces the SAG’s discharge screen’s oversize material. A 14 foot diameter ball mill ensures final grinding before the flotation stage.Many control strategies were used at the SAG over the past few years. Fuzzy Logic was first used in 2007 in order to control tonnage feed to the SAG. This first version only measured the value of the variables without taking into account their rate of change. Revisions were made over the course of the last few years to improve controller performance. Other variables were added such as slurry density and crusher Closed Side Setting (CSS). The previous revision of the Fuzzy Logic was done in 2009 with a review of the rules only."

Jan 1, 2013

By Kjell Winther

"Hydralift Scanmec introduced early in the eighties a new and different mill design for very large grinding mills. The design described has actually no size limitation upwards and is so far suggested with motor power up to 40 MW. The mill is furnished with gearless ring motor drive transmission. It is totally fabricated, without heavy castings. The first installation, an 8, 1 MW ball mill dia. 6,5 m x 9,65 m length, has been in continous operation in 13 years without problems. Total grinding costs has been reduced with 3 0% compared to traditional smaller mills. Reductions has been achieved in maintenance cost, power consumption, liner wear and grinding media consumption.So far 3 ball mills of the described design are delivered and in operation, one grinding Iron ore and two grinding Nickel ore.IntroductionThe design of mills for mineral ore dressing has basically been unchanged since grinding in mills started some I 00 years ago, in spite of the fact that mills have grown larger and larger. This has resulted in structural and mechanical problems, causing expensive failures and loss of production.Hydralift Scanmec engineers were designing mills for more than 20 years according to the old «rules». As they experienced interest for an increase in the mill size at the time when reports about failing mills were published, they started analyzing the different mill parts to find new solutions. One goal was to only use elements from proven technology in the new design. Two key items were ring motor (wrap around motor)(Isch et al. 1977, Meintrup and Klein 1982, Ranze 1983) and large diameter pad bearings (wrap around bearings)(Fuller 1984), both acknowledged from other industries."

Jan 1, 1995

By Zhuo Chen, Jun Zhou, Jiemin Zhou

Samples of the reacting suspension particles were taken from the reaction shaft of a commercial flash furnace at different heights. The processes of matte and slag formation and morphology of the samples in the shaft were observed and analyzed. Variations of matte and slag composition in the shaft were investigated. By analyzing the samples taken from the settler at different locations, settler processes were studied such as slag formation, agglomeration and separation of matte-slag phases, Fe3O4 reduction, copper-in-slag reduction etc. In accordance with the characteristic of matte and slag formation the flash furnace can be divided into 6 functional regions, and a mechanism model called as “Micro bath process” is proposed for matte and slag formation in a commercial flash furnace. INTRODUCTION During flash smelting, concentrate particles scattered in the reaction shaft complete their oxidation reactions in suspension. The droplets produced fall into the settler beneath with a small amount of un-melted solid particles, agglomerate and separate into matte and slag layers which are tapped out from their tap holes separately. With respect to the extent of slagging reaction in the reaction shaft, there isn’t any commonly accepted understanding in literature (Kimura, Ojima, Mori & Ishii, 1986; Kemori & Kondo et al.,1988; Kemori, Denholm & Kurokawa, 1989; Fagerlund &Jalkanen, 2000). Some assume that the slagging reaction in the shaft can be ignored and some propose that all slag is produced in the shaft. With regards to the characteristics of the physical-chemical changes of concentrate particle in the reaction shaft, although there are some research results reported from pilot scale and commercial scale experiments (Kemori, Ojima & Kondo, 1988; Hagni, Vierrether & Sohn, 1988; Jorgensen, Taylor, Dickinson & Stevenson, 1992; Swinbourne, Simak & Yazawa, 2002; Kivinen & Tuominen, 2005), they are generally limited themselves to theoretical analysis and calculations. No studies are published concerned with the processes of matte and slag generation in the shaft, quantitative analysis of the processes, variations of matte and slag composition and morphologies of the melts along the axis of the shaft, etc.

Jan 1, 2019

By A. Desbiens, A. Pomerleau

During the summer of 1994, a new PID-based control strategy was installed on line B of the grinding circuit at the Kidd Creek Division of Falconbridge Ltd. Part I of this paper described the methodology used to select the appropriate control strategy using a phenomenological dynamic simulator. Part II presents the implementation of the control strategy. Prior to the controller installation, it was necessary to solve various problems related to the process, such as a cyclic behaviour of the rod mill feed tonnage, a problem related to the mill water source and the calibration of the flowmeters. Once these problems were solved, the control strategy was accomplished in two steps. Step 1 corresponds to the installation of control loops to regulate the pump box level and the cyclone overflow density. Step 2 describes the implementation of a loop to control the cyclone feed density. According to Part I, a loop to control the circulating load is also part of the original design. However, reasons are given to explain the rejection of this loop. For both steps, technical procedures such as filtering, process identification and controller tuning are detailed. Finally, the operator’s interface is briefly described.

Jan 1, 1997

By S. Caron, P. Radziszewski

Industrial practice in mineral processing shows that an important problem in understanding and monitoring in-mill parameters is due to the lack of fundamental knowledge and appropriate sensors. However, over the last decade, Discrete Element Method (DEM) modelling has shown an interesting potential in describing the fundamentals of grinding mill behaviour, in improving the understanding of internal grinding mill dynamics, and in developing solutions to industrial practice. With the objective of bringing this modelling technology into the concentrator control room to assist operators, this paper aims to describe the main elements needed to apply this emerging and developing technology to on-line mill performance monitoring.

Jan 1, 2004

By Dale Lens, W. S. (Wayne) Cusitar

"The use of continuous loading and conveying technology for mining is currently practiced in relatively few mining environments and, even in these cases, on a non-exclusive basis. For the most part, and particularly in hard rock mining, appropriate equipment technology has only recently been developed for continuous loaders, mobile low profile crushers and flexible face conveyors. Mining R&D work by Inco Limited has promoted the development and proving of a loader suited to hard rock conditions and capable of sustained loading rates of500 tonnes per hour. Current R&D work at Inco will test the production capabilities of a low profile mobile crusher by CMS/Eagle and a flexible/ mobile face conveyor system by DME. This follows successful production testing of the Belt Bender concepts in potash mining in Saskatchewan and the development of enhanced extensible conveyor equipment features by DME. Numerous applications are seen for variations of the LCC technology in soft rock, hard rock and surface mining environments. Introduction In some respects, this paper is an announcement of new technology which has the potential to bring revolutionary change to the mining industry. It is also the story of technology transfer, in which mining concepts that have developed independently in underground soft rock and hard rock mines and in surface mining operations are being brought together for a common benefit. It is also the story of key developments in equipment technology which 'complete the cycle' of cooperating technical capabilities to enable the revolution to begin. The phrase ""technological revolution"" requires some defmition: an equipment innovation, or invention, or improvement, will only be revolutionary if its use gives rise to a significant new mining practice."

Jan 1, 1987

By Donald Leroux, Dave Scott, Giovanni Di Prisco

"The Lady Loretta lead-zinc deposit in Northwest Queensland, Australia contains an average of 5.9% lead, 17.1% zinc and 97 g/t silver. Ore mineralization is mostly comprised of fairly complex intergrowths of pyrite, sphalerite and galena. Starting in 1998, Noranda Inc., the major joint venture partner of the project, conducted extensive metallurgical test work, which culminated in July - August 2000 in a series of Pilot Plant tests. A common thread to all the metallurgical work has been the deportment of a large portion of silver into non-payable metallurgical products. Average silver distribution from four Pilot Plants shows a distribution of silver in lead concentrate of 28%, whereas silver in zinc concentrate was 49%, and 23% in the final tails.The consistently poor silver recovery as well as the fairly unusual silver distribution, particularly in zinc concentrate, was considered an issue to be thoroughly investigated. A mineralogical plan was devised to determine if these particular metallurgical results were somewhat related to the nature and mode of occurrence of silver carriers. Work was performed to determine discrete silver-bearing minerals and/or silver contained in solid solution in a suite of commonly occurring sulphides. Ore microscopy, SEM methods, Electron Microprobe and Ion Microprobe analyses were all used to answer these questions, and to find the silver carriers, so a metallurgical plan could be devised to improve silver recovery.INTRODUCTIONPotential economic exploitation of the Lady Loretta deposit in Queensland, Australia is driven by revenue derived from zinc and lead flotation concentrates and co-product silver recovery in lead. Relatively low recoveries of payable silver to lead concentrate, and high silver distribution to zinc concentrate necessitated an investigation into the natu"

Jan 1, 2002

By Dave Price

"Canada is scheduled to become the 4th highest diamond revenue producing country in the world by year 2004 with the already operating Ekati Mine and the anticipated operation of the Jericho Mine in 2002 and the Diavik Mine in 2003.This paper provides an overview of worldwide diamond production statistics and a brief introduction to a diamond processing plant. The dense medium separation (DMS) extraction process is presented and this process is discussed in more detail with respect to the extraction of diamonds in terms of feed preparation, dense medium, dense medium cyclones, ferrosilicon recovery and dense medium cyclone operating efficiencies.INTRODUCTIONThe Ekati Diamond Mine in the Northwest Territories started commercial production of diamonds in the 4* quarter of 1998. At full production, the mine is anticipated to produce annually some 3 million carats of diamonds. The Jericho Mine in Nunavut Territory and the Diavik Mine in the Northwest Territories are anticipated to come into production in the 1'' quarter of 2002 and 1st half of 2003 respectively. The combined annual diamond production of these three mines will total approximately 10.34 million carats by 2004, making Canada the 4~ highest diamond revenue producing country in the world.A diamond processing plant initially utilizes crushing, scrubbing and screening in the beneficiation process to liberate diamonds from kimberlite ore and size the product for further treatment through DMS. Alluvial diamond operations do not require initial crushing and scrubbing but incorporate a feed preparation and sometimes a recrush facility with the DMS plant. The heavy sink product from the DMS, which contains diamonds, is further upgraded through x-ray separation and high intensity magnetic separation prior to producing the final diamond product.DMS is a relatively simple separating principle. A mixture of particles of different density is immersed in a dense fluid, so that particles having a density lower than that of the fluid will float while those of heavier density will sink. The translation of the float-sink principle from a laboratory method to continuous industrial practice offers the prospect of very precise mineral separations based on density differences alone."

Jan 1, 2000