Search Documents

An intensive safety campaign at Mount Isa Mines Limited from 1956 to 1966 saw the lost time accident frequency rate fall to half its original level. A review of the safety programme was carried out in 1967 and in 1968 the Five Point Safety System was introduced. The seven years since its introduction have been years of significant achievement both in production and safety. Improving safety is a fundamental part of Mount Isa Mines Limited's policy and this system has been a major tool in implementing that policy. To be successful personnel need to be prepared and trained for its introduction and subsequently counselled on its use. A carefully prepared programme is required to phase in various aspects of the system and to make use of complementary steps. The system has been a success and it is anticipated that the continued drive to improve the use of principles of the system will further improve safety. It is hoped that this paper will be of value to those personnel concerned with industrial safety in Australia.

Jan 1, 1975

Since the earliest recorded prospecting of the 1860's mineral exploration and mining in Fiordland has been discouraged by the formidable physical difficulties presented by its isolation, extremely rugged relief, treacherous coastal waters and generally unfavourable weather conditions. Government assistance was often sought by the miners and prospectors but little, if any, support or encouragement was received after the initial period. During the 1840's decorative marble was quarried at Caswell and Dusky Sounds. A prospector discovered and attempted to mine copper sulphides to the north of Dusky Sound (Parks Mineral Beds) and near Mt Solitary. A small Pb, Zn, Cu, Ag, Au bearing quartz reef was discovered and driven on in the granite coast line of Preservation Inlet (Bradshaws Reef) and the ore roasted on site. Alluvial and quartz lode gold was discovered at Preservation Inlet in the 1890's and led to the recorded recovery of 11 000 oz of mainly lode gold. Falloff in grades with depth, thinning and splitting of the reefs and the high mining costs at this location led to a virtual abandonment of the field by 1906. In the late 1950's and early 1960's the geology of Fiordland was mapped by the Geological Survey at 1:250 000 scale, but field work was largely confined to the shore lines of the coast and fiords. In view of the physical difficulties it is not surprising that mineral exploration and mining up to 1970 was limited to the scant attention outlined above.

Jan 1, 1977

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003

This paper discusses the concepts of core risk associated with mining projects and operations and illustrates the types of core geotechnical risks and consequences that may relate to a range of different mining methods, with recommendations on risk management procedures to ensure that the core risks are under constant and ongoing scrutiny and priority management focus. These core geotechnical risks can and should be identified at the initial mining method selection stage, during a feasibility study. They should form part of the auditing of the project and the decision-making regarding the project viability. They should then be built into the ongoing management structure of the project, right through into ongoing operations, with regular audit and review.

Jan 1, 2003

The Mt Lyell Mine at Queenstown, Tasmania was re-opened in 1995 by Copper Mines of Tasmania Pty Ltd, a wholly owned subsidiary of Mt Lyell Mining Co Ltd. The re-opening followed over 100 years of copper and gold mining at Mt Lyell. Major changes in practice were implemented across the site. Preventing further damage to an already disturbed environment was a major priority. Sublevel caving, at a lower cut-off grade, replaced open stoping for the deep underground mining. Development and later stoping are handled by a contractor, National Mine Management Pty Ltd, in the largest underground contract awarded at the time. Large scale sublevel caving was new to Mt Lyell and not widely practised in Australia, requiring studies and systematic development of the method, particularly in drilling and blasting. Rehabilitation and upgrading of mine infrastructure have been and will continue to be a challenge. The mine has, since 1995, returned to being a stable producer with potential for growth.

Jan 1, 1998

By K Sanematsu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Ore deposits of rare earth elements (REE) in South-East Asia are classified into four types: carbonatite, allanite, ion-adsorption and placer. Occurrences of the carbonatite deposits are confined almost exclusively to the Red River Fault Zone of northern Vietnam. Since the carbonatites contain dominantly REE fluorocarbonates (eg bastnasite) and lesser amounts of monazite, they are rich in light REE but poor in heavy REE. The ion-adsorption type deposits and prospects were found in Myanmar, Vietnam and Thailand. The ion-adsorption ores generally show lower REE grades than those of the carbonatite type and placer deposits; however, they could be enriched in HREE, which are more precious and scarce commodities than LREE. The ores consist of weathered granites with a significant amount of ion-exchangeable REE, which are extracted by using a dilute electrolyte solution. The ion-exchangeable REE are likely to be sourced from REE fluorocarbonates, allanite and titanite because these minerals are relatively susceptible to weathering and release REE3+ ions into soil water. In contrast, monazite and xenotime are resistant to chemical weathering and could form placer ores. Placer monazite and xenotime have been processed as by-products of placer Sn, Zr or Ti in Malaysia, Thailand and Indonesia, although the current production is small.CITATION:Sanematsu, K, 2015. Rare earth element deposits and prospective areas in South-East Asia, in Proceedings PACRIM 2015 Congress, pp 671–678 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By A Jyoti, J R. Black, R R. Haese, E O. Ansah

Copper (Cu) is a critical metal in the transition to a low-carbon power supply. Presently, low-grade copper sulfide ores account for almost 80 per cent of the global reserves. Large amounts of water are required to process these low-grade copper ores. The mining industry utilises lixiviants from recycled water from different sources to conserve water, whilst enhancing Cu recovery. Some utilise intermediate to pregnant leach solutions, sea water, and processed water from electrowinning circuits with highly variable concentrations of ions. Previous studies have highlighted the formation of precipitates that passivate the surfaces of minerals in these low-grade copper ores and/or block flow paths for lixiviant during heap leaching. In this study, we utilised concepts of phase replacement to devise an innovative means of controlling precipitation and increasing copper recovery using industrial brine as opposed to freshwater. We propose the formation of Al-rich phases (such as AlSO4 + or alunite) to replace iron sulfate and iron hydroxysulfates (such as jarosite) during the chalcopyrite dissolution-precipitation mechanism. The rationale is to have available Fe3+ throughout the chalcopyrite leaching process. We tested this method by carrying out various batch experiments using CaCl2, AlCl3, and NaCl industrial brine types compared to freshwater and explored the capacity to leach Cu from chalcopyrite. There is higher Cu recovery during oxidative leaching of chalcopyrite in industrial brine with 91 per cent recovery using AlCl3-rich brine, 84 per cent with NaCl-rich brine, and 56 per cent with CaCl2-rich brine as compared to 35 per cent recovery using freshwater. In the absence of Al3+, various forms of iron sulfates, and jarosite are formed, reducing the availability of Fe3+ for chalcopyrite dissolution. The introduction of Al3+ leads to the formation of AlSO4 + species, thus lowering sulfate activity and the tendency for K-jarosite formation.

Aug 24, 2022

By M Ahmed

Reliable face support pressure is necessary for shield driven tunnels in cohesionless soils to prevent excessive ground movements. This paper presents experimental work on stability of a tunnel face using transparent soil models aiming to obtain magnitude of tunnel face minimum supporting pressure, failure pattern and extension of failed zone. A model tunnel was preinstalled in transparent soil which was supported at the face by means of water pressure. Tests were performed by reducing supporting pressure until collapse occurred. Model tests were sliced optically with laser sheet and images were captured for every decrement in tunnel supporting pressure. Later, these images were analysed by digital image correlation (DIC) and vector fi elds of incremental displacements were obtained. Values of minimum support pressures were given for different cover/diameter (C/D) ratios. Geometry of the failure zones depicted for different (C/D) values and appeared to be of chimney shape with a limited extension front of the face. A minimum support pressure was achieved with support pressures as low as 10 ± 1 per cent of the effective vertical stress at the tunnel axis. The stability of the tunnel face was related to the coefficient of active earth pressure with C/D ratio having a small effect on the magnitude of required pressure at collapse. In general, results of the study were in agreement with current knowledge of full-scale situations.

Mar 8, 2011

The performance of the Australian Mining Industry over the past 10 years using key indicators of production, revenue, aftertax return investment, together with key cost elements, market changes and ore reserves is briefly reviewed. The elements of competitiveness are discussed forthe industry and the effects of Government charges and policies relating to existing operations are outlined. There is a demonstrated need for improvements in competitiveness in direct and indirect costs and for improved access to resources for the mining industry to continue to grow and add to Australia's economic growth.

Jan 1, 1987

By A Stasi, B Brice

Water is a limited and precious resource in Australia. Because of the increasing demand for water from all sectors of the economy and the variability in supply, efficient management of water resources is of vital importance. The national water reform agenda has provided a strong impetus to all states and territories to progressively move towards more efficient and sustainable water management. The Queensland Water Act 2000 is the legislative framework for providing water for the environment and for planning for the security of supply to water users. The comprehensive water planning process prescribed in the Act results in new tradeable water allocations that are separate from land. These water allocations are well specified and can be traded on a permanent or temporary basis. Trading of water allows it to move to its highest value use, thereby encouraging the most efficient distribution of this limited resource. In addition to transferring ownership of water allocations, it is also possible to change the attributes of the allocation, such as the location from which water may be taken. Changes to water allocations are subject to approval from the resource manager. Pre-testing allows for certain changes to be approved very quickly, making the trading process more streamlined and cost effective. Temporary trades, or seasonal water assignments, currently account for the majority of water trades in Queensland. However, permanent trading activity is expanding steadily as old water entitlements are converted to tradeable water allocations and as the market matures. The permanent trading market provides significant opportunities to the mining sector. It allows mining companies to buy water allocations at market prices without compromising environmental outcomes or causing third party impacts.

Jan 1, 2006

By D La Rosa, A Jankovi, A Dance, W Valery

This paper presents the methodology for optimising blasting and comminution processes in terms of fragmentation developed by Metso Minerals Process Technology Asia-Pacific and South America (MMPT). The methodology is called process integration and optimisation (PIO) and involves a number of steps: benchmarking, rock characterisation, measurements, modelling/simulation of blasting and comminution processes and where required, material tracking. The measurements collected while at site are combined with rock characterisation and definition of ore domains to model the complete process chain. These data are used to develop site-specific models of blast fragmentation, crushing, grinding and flotation. This allows customised blast patterns to be developed that optimise both crushing and grinding performance. For each domain, blast designs are recommended to generate the optimal fragmentation size for downstream processes. The objective is to minimise the overall cost for the entire process and the changes often have a positive impact on the mining operation. Process constraints such as wall stability, ore dilution, muck pile characteristics, size of mining equipment, size and installed power of crushing and milling equipment and other process bottlenecks are considered in the blast designs. This methodology has allowed many operations around the world to significantly increase their production: generating typically five to 20 per cent higher concentrator throughput. A number of case studies will be discussed in this paper to describe the structured approach taken and demonstrate the benefits that are achievable. This paper will focus on the role of blasting in the optimisation of the entire mine to mill process chain and discuss elements of the PIO methodology: rock characterisation, fragmentation modelling and measurement, the relationship between fragmentation and mill throughput and material tracking.

Jan 1, 2007

By A Thornton, D Engelhardt, J Woodg

Grinding is a critical part of nearly all mineral processing operations. It is the largest consumer of energy on the mine site (and thus indirectly a producer of greenhouse gas through the generation of electrical energy at the power station). Since comminution is one of the main consumers of electrical energy worldwide, efficient control of grinding mills is of paramount importance. Mill Auto-Pilot is a control system developed for SAG mills to stabilise load and power and improve the efficiency of control and increase throughput. A dynamic, mechanistic model of the grinding circuit is used to determine circuit parameters which can not normally be measured using conventional instrumentation. The circuit model is built from models of the unit operations (such as conveyors, SAG mills, cyclones, sumps, etc), and so captures the dynamic complexities and interactions of real circuit operation. CSA Mines at Cobar NSW accepted an offer to be the reference site for Mill Auto-Pilot and the system was installed in March 2004. In this application the model is used to predict mill load mass, mill solids residence time and cyclone underflow density. These parameters are used to control mill load, power and mill discharge density. The outcomes of the introduction of Mill Auto-Pilot at the CSA Mine are discussed.

Jan 1, 2004

By N Madani, S Abulkhair, N Morales

Conventional geostatistical algorithms cannot reproduce bivariate complexities such as inequality constraint, nonlinearity and heteroscedasticity. Poor reproduction of these features may decrease the accuracy and reliability of mine planning results. For example, it is not unusual to have an inequality constraint between primary and disturbing elements in a metalliferous deposit. Implementation of traditional methodologies for such complex data sets can lead to the incorrect reproduction of a bivariate relationship, which will affect the validity of NPV results. In this paper, an iron data set containing iron and silica grades with an inequality constraint between variables is introduced as a case study. This study proposes an algorithm based on a hierarchical sequential Gaussian cosimulation integrated with inverse transform sampling. The proposed methodology considers the linear inequation between two variables in the hierarchical cosimulation process to reproduce an inequality constraint. As a comparison, conventional sequential Gaussian cosimulation is also applied to the same data set to demonstrate the difference in bivariate relationships from both models. Unlike the proposed algorithm, the conventional cosimulation cannot reproduce an inequality constraint and slightly overestimates silica grades. The modelled realisations are then used to assess the uncertainty of a plan and generate a stochastic strategy that adapts the destination of the blocks depending on the scenario. Two-stage stochastic long-term production scheduling takes extraction decisions using average information (ie e-type model) and ore/waste destinations based on geostatistical realisations. As a result, the proposed strategy is closer to the upper bound, highest possible NPV for each realisation, than to the lower bound, deterministic strategy that does not manage the risk of sending extracted material to wrong destinations. Furthermore, Comparing production schedules resulting from proposed and conventional geostatistical methodologies shows the importance of inequality constraint reproduction and more accurate long-term mine planning.

Nov 8, 2021

By P Dean, M Elmouttie

Radar monitors are now widely used in surface mining for monitoring slope deformations and predicting failure events. Their introduction has facilitated better management of risk associated with slope failure during mining and therefore protection of personnel and equipment. However, a wellrecognised problem is that radar monitors only measure deformation directed towards the detector (line-of-sight bias). This bias can lead to misinterpretation of deformation size, rate and failure mechanism, and therefore miscalculation of failure volume, which can significantly impact safety and productivity. This paper presents recently completed research and field trials into the feasibility of using low cost vision systems to mitigate this issue. It has been demonstrated that by integrating a computer vision system with an existing slope monitor, high precision tracking of features in the field of view can be performed. Combined with assumptions on the deformation characteristics, the true 3D deformation vector can be estimated. The applicability of using this technique for monitoring iron ore mine slopes is discussed.

Nov 8, 2021

Many block caving operations experience difficulties during undercutting, resulting in draw horizon damage, production loss and extensive drift repairs for the life of the block cave. This paper deals specifically with block cave undercut aims strategies, methodologies and management to avoid the problems indicated above.

Jan 1, 2000

By P Corbett, P Sheffield

Springvale Mine is an underground coal mine in the western coalfield of New South Wales which utilises retreat longwall mining technique. The mine encountered significant gateroad floor heave issues during retreat of LW415. Floor heave has subsequently impeded longwall advance as well as longwall bolt up and recovery to some extent during the extraction of the next five longwalls. Floor heave at Springvale Mine develops throughout the lifecycle of the mine roadways, and is most prevalent in longwall gateroads. Floor heave has been measured as early as 2 weeks after roadway development and continues to develop through the post-development phase, with a rapid increase in close proximity to the longwall face. This paper presents a case study of the evolution of understanding of floor heave behaviour at Springvale Mine based on geotechnical characterisation, an intensive convergence monitoring program (roof and floor movement) and spatial correlation of monitored locations with longwall face position. The analysis considers previously known factors contributing to floor heave including mining depth, geological and physical properties of the rock mass and mine design geometry. Investigation results indicate a strong correlation between floor heave magnitude and roof dilation magnitude, geophysically inferred faulting in underlying strata, areas of localised stress concentration and mine roadway dimensions. This paper also discusses the predictive model which was developed as a result of the study, which is now the basis of the floor heave removal program used to manage roadway convergence at the mine. Floor heave monitoring, prediction and management strategies (including floor reinforcement and removal) are also discussed. CITATION:Sheffield, P and Corbett, P, 2018. Managing floor heave in an underground longwall coal mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 78–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Safarian, D Hariswijaya

Treating bauxite residue as an alternative source of metals for iron and aluminium industry is an approach to promote circular economy in metal industries. Reduction of metal oxides with H2-based process is an important step on decarbonisation of metal industry. In this study bauxite residue pellets were prepared and were reduced with different H2-H2O gas compositions at different temperatures which yielded with various degrees of reduction. The bauxite residue pellets were made from a mixture of bauxite residue and Ca(OH)2 powders and sintered at 1150°C. Hydrogen reduction was carried out on the oxide pellets using a resistance furnace at elevated temperatures in controlled reduction atmosphere of H2-H2O gas mixtures which resulted in reduction of iron oxides in the pellets. Unreduced and reduced pellets were subsequently heated to 1400°C to study their smelting behaviour using differential thermal analysis (DTA) and thermogravimetric analysis (TGA) technique to investigate the evolution of phases related to slag formation via smelting. Equilibrium module of Factsage™ ver 8.1 was utilised to analyse results of thermal analysis. It was observed that Tricalcium phosphate-β (CaP2O8), Bredigite (Ca7Si4MgO16), Rankinite (Ca3Si2O7), and calcium alumino ferrite (Ca[Al,Fe]6O10) were formed during thermal analysis as intermediate phases. The initial slag formation for sintered and reduced pellets occurred at 900°C which mainly contains calcium and small amount of strontium component. The slag formation rate increases significantly starting from 1100°C when iron oxides started to form initial molten slag phase which then followed by other oxides dissolution in the system. Gas formation was observed at 1180°C and it was found that the gas to be released from unreduced pellets is O2 meanwhile the gas to be released from reduced pellets is SO2 gas. Gas formation rate for both pellets start to increase at 1280°C when the remaining chemically bonded gas start to be released from the system.

Jun 19, 2024

By C M. MacRae

The characterisation of high-P iron ores by field emission gun electron probe microanalyser (FEGEPMA) was carried out to determine elemental associations in iron oxides sensus lato and, using this knowledge, to speculate on possible P incorporation mechanisms in goethite. Quantitative data was collected from two goethite-rich bulk ores and results showed that in both samples goethite was the main repository for phosphorus. The P-rich goethite also contained elevated levels of both aluminium and silicon.To understand the mechanism of P incorporation in goethite, high-P grains were located by coarse mapping of polished blocks with the FEG-EPMA. Analysis of element distribution maps collected on the P-rich grains showed that low-P regions within grains were typically associated with low-Al and high-Si, whereas high-P regions were associated with high-Al and low-Si. Based on follow-up quantitative analyses, a coupled substitution mechanism for phosphorus incorporation within goethite was proposed: 2Si4+ = 1P5+ + 1Al3+. Additional quantitative analyses on further examples indicated the mechanism was only valid for Si contents in goethite of <1 wt per cent.Preliminary transmission electron microscope (TEM) studies confirmed the presence of P, Al and Si in goethite.

Jul 11, 2011

By P Hawkes

Within the mining industry computers have made their most significant impact with 3D design, visualisation and resource modelling/ optimisation. Recently, the application of computers to data gathering and accounting functions has also started to reap benefits. These two areas of application cover the beginning and end of the mining process. There has been limited use of computers on the middle section, the actual mining process. This is interesting when considering the relative proportion of overall mining costs that this section produces. There is a certain amount of irony in the lack of mining application software for developing accurate budgets compared to the systems/software then used to review performance against budget. Computers have been used extensively in the manufacturing industry to design, model and simulate the manufacturing process. This has not been extended to the mining process. But, we all strive to have an open pit that replicates a manufacturing plant û smooth, efficient, optimal production. If we could model mining operations with the confidence of plastic box makers we would reduce risk by an order of magnitude, improve planning and focus on value drivers. Cost û benefit analysis would be easy. The extrapolation of manufacturing to mining process models is difficult. The variables in the manufacturing process are fewer in number, have low volatility and are highly predictable. The time between a box falling on a conveyor belt and falling off is very consistent. Mining is quite the opposite. It has large numbers of variables, some of which are unpredictable and volatile. The time to fill an excavator bucket could vary by 30 per cent and the frequency distribution is unlikely to be a mathematically simple normal distribution. Further, each of these variables can be distorted by one-another û they are interrelated. The mining process is a disjointed flow of parcels whereas manufacturing is a controlled continuous feed. A loaded truck might join a ramp and follow a slow water cart up. This is the equivalent of a localised voltage drop on equipment in a manufacturing plant. The manufacturing plant is quite likely to rapidly recover to full capacity. Whereas the slow truck might throw the mining fleet cycle out of balance for hours û trucks queuing at the ROM bin and so on. A mining process simulation has been created that addresses these mining variable issues to produce a highly accurate model of the open pit mining process. The number of uses for such a model is growing rapidly as it is being utilised for a variety of projects within the industry. This paper discusses the need for and application of mining process models.

Jan 1, 2003

By S Jayakumari, E Ringdalen, V Canaguier

Silicomanganese (SiMn), containing approximately 16–30 per cent Si, is produced in submerged arc furnaces using various Mn sources and quartz as the primary raw materials, along with fluxes and reductants. In the high-temperature zone known as the coke bed, a silica-rich slag is formed. SiMn is produced through the reduction of SiO2 from the slag. Dissolution of quartz into slags with different compositions, the primary slag formed from the Mn sources and flux before any MnO reduction occurred, representing conditions at the top of the coke bed, and dissolution of quartz into a partially reduced slag to simulate conditions inside the coke bed has been investigated. Experimental investigations were carried out to study the dissolution of quartz particles of varying sizes, 5 mm and 25 mm in synthetic slags with different compositions at temperatures between 1400°C and 1600°C, with varying holding times. Observed results are compared with liquidus compositions and equilibrium phases for original and formed slags. Particle size has been shown to be of little importance for the dissolution. Quartz dissolved more easily in slag at top of the coke bed than slag in the coke bed. Complete dissolution was observed after 30 mins at 1600°C in all cases, but not after 0 mins.

Jun 19, 2024