Search Documents

By Iley J. D, Siviour N. g, Moffatt R. J

The process of desilverising by fractional crystallisation with reflux was investigated through laboratory batch tests and continuous laboratory bench scale tests at CSIRO Clayton, to a 300 kg/hr pilot plant at Port Pine. The pilot plant built at BHAS comprised a vertical cylindrical refining column with internal diameter 250 mm and height 3.2 m, attached at the top to an off-set cylindrical stirred crystalliser tank. Crystals were made in the crystalliser by intermittent immersion of steel cold fingers, which were water cooled between immersions. Gas heat was used for melting the crystals at the base of the column and for side compensation heating. A computerised in strumentation system was employed for data logging and for controlling some critical plant operations. A mechanical device was first employed to promote counter-current plug flow of crystals down the column against the rising stream of reflux liquid, but this was found to be unsatisfactory owing to excess noise, frequent mechanical failure, and excessive accumulation of dross. Plug flow was finally promoted by pulsing the column. Low silver levels, less than 1 gitonne, were achieved with both methods of crystal transport under total reflux conditions. The pulsed column gave results for silver and bismuth which agreed with the theoretical predictions of a computer model, but there was some selective drossing of antimony. In the mechanically agitated column, excessive drossing promoted selective removal of most of the antimony and some of the bismuth, and the results after extended operation were well removed from the theoretical predictions. Plant failures and operating problems prevented the achievement of satisfactory product quality with the necessary reliability under production conditions. Other priorities necessitated the termination of the project before the process could be optimised.

Jan 1, 1989

By Y Gu, R Fandrich

Traditionally, characterisation of the mineralogy and textures of ore and rock samples were based on observations of hand specimens and thin sections using an optical microscope. The extent of the data collection was limited by the available tools and thus variations in mineralogy and texture were generally not described by quantitative data. These qualitative to semi-quantitative approaches, even though well established over the years, resulted in variable observations and data sets. The data were unlikely to be representative of a sample and limited statistical validity meant the results could not be reliably used in modern digital mining design and planning. With recently developed SEM based quantitative mineralogy tools and the corresponding methodologies, ore textures can be quantified and compared numerically. The numerical data can not only enhance the understanding of an orebody in geological terms, but can also be used in the creation of metallurgical models for mine and mineral processing design and simulation. These capabilities provide valuable inputs to risk assessment studies and the evaluation of mineral projects.

Jan 1, 2007

By B Davis, M Wallace, J Stewart, C F Burrett, J B. Cannell

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Sepon district in Lao PDR contains 1.8 Mt of JORC (2012) compliant contained Cu resources in addition to >4.5 Moz of Carlin-like Au in a Palaeozoic sedimentary package. The Cu deposits are proximal to an EW lineament of Permian rhyodacite porphyry (RDP) intrusive centres that are characterised by intense barren quartz stockworks. The Khanong deposit (42 Mt at 3.0 per cent Cu mineral inventory) is a carbonate replacement intermediate sulfidation deposit verging on a high sulfidation environment, where abundant pyrite, copper sulfides (chalcopyrite, bornite, trace enargite), copper sulfosalts (including tennantite – tetrahedrite, colusite), and base metal sulfides (sphalerite and galena) have replaced low dipping dolomite and limestone layers, forming a manto-style orebody fed by steep dipping intensely silica-pyrite altered structures. The Thengkham deposits (54 Mt at 1.5 per cent Cu) are composed of prograde skarns (garnet, clinopyroxene) and mineralised retrograde skarns (chlorite, magnetite, hematite, epidote, sericite, talc, serpentine, carbonates, sulfides) which are irregularly and semi-continuously distributed around an elongate 4 km long intrusive centre. Thengkham and Khanong have been strongly supergene enriched, forming secondary chalcocite breccias and exotic malachite zones.The Carlin-like Au deposits display a range of stratigraphic and structural controls and lie outboard of the Cu deposits. Similar structural controls, alteration assemblages and trace mineralogies suggest that gold and copper mineralisation are temporally and genetically related. It is hypothesised that the differences in style of Cu and Au deposits across the Sepon district are related primarily to palaeodepth and proximity to the intrusive centres.CITATION:Cannell, J B, Stewart, J, Williams, P, Wallace, M, Burrett, C F and Davis, B, 2015. The Sepon copper deposits (Laos) and their relation to Carlin-like gold mineralisation, in Proceedings PACRIM 2015 Congress, pp 399–408 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M Berndt

Four siltite-argillite rock samples were characterised (particle size, chemistry, mineralogy) and subjected to laboratory dissolution testing for 36 to 298 weeks. In two samples sulfur (0.99, 1.69 wt per cent) occurred largely as pyrite, and in the other two samples sulfur (0.96, 1.93 wt per cent) occurred predominately as potassium jarosite. The observed rate of sulfate release from the pyritic samples was one to two orders of magnitude greater than that from samples containing potassium jarosite. Drainage pH values from the pyritic samples were one to two units lower and acidities were ten to 70 times higher than associated values from the potassium jarosite samples. Geochemical modelling supported the hypothesis that pH and concentrations of sulfate and potassium in drainage from the potassium jarosite samples were controlled by the limited solubility of potassium jarosite. This dissolution produced an iron-dominated mineral phase, but iron concentrations in the drainage were well below those predicted by ferrihydrite solubility.

Jan 1, 2003

By N Belluz, L Johnson, N Wiwoho, P Manning

The Kucing Liar skarn deposit is located in the Ertsberg mining district, which also contains other skarn deposits and the Grasberg porphyry copper û gold deposit. The Ertsberg district is located in the province of Irian Jaya, IndonesiaÆs easternmost province. Mining development began in the Ertsberg district in 1972 with the mining of the Ertsberg deposit. Daily production in the district now averages about 230 000 tonnes of ore, with the bulk of the ore coming from the Grasberg open pit and the balance from underground mining of skarn deposits. During 1998, 45 218 additional metres of drilling were conducted to delineate and understand the Kucing Liar orebody. The deposit was first intersected in drill holes in 1994 and then was intersected in underground workings located about 1000 metres from the discovery drill hole in 1995. Initially, the two intersections were thought to be different orebodies but are now realised to be different parts of the same orebody. The Kucing Liar deposit consists of magnetite û copper û gold replacement and skarn mineralisation in favorable Tertiary and Cretaceous units. The deposit is approximately 2000 metres in length and averages about 200 to 250 metres in thickness. The width varies from 400 to 600 metres. Drilling in 1998 was directed towards delineating the deposit on its NW and SE ends and to determine its down dip extension. Reserves for the deposit at the end of 1998 stand at 320 million tonnes at 1.4 per cent copper, 1.4 g/t gold, and 5.3 g/t silver. Many important questions remain to be answered concerning the relationship of the Kucing Liar orebody to the major faults in the district and to the Grasberg intrusive complex which contains the Grasberg orebody. Continued exciting developments are anticipated as work to understand the deposit by drilling and geologic study continues.

Jan 1, 1999

By R Jones

OneSteel Whyalla’s grate-kiln-cooler pelletising plant was commissioned in 1968 processing haematite feed from the local South Middleback Ranges mining area. The existence of a magnetite resource beneath the haematite ore at Iron Duke had been known for some time. In 2004, a decision was made to covert the primary iron source for the Whyalla steelworks from haematite to magnetite – known as project magnet. The intent of the project was to convert the feed to the steelworks from haematite to magnetite and to free up the remaining haematite resource for export. The pelletising plant was cut over to a magnetite feed in 2007.The thermochemical differences of magnetite compared to haematite are threefold:1. the introduction of an exothermic reaction during conversion of magnetite to haematite,2. the absence of bound water which existed within the haematite, and3. lower gangue content requiring lower fluxing levels and therefore lower calcination energy demand.The combination of these differences results in a significantly different induration requirement for magnetite as compared to haematite. The change therefore required extensive research and test work to design modifications to the furnace and to ensure appropriate risk mitigation for the Whyalla steelworks.Preliminary pot-grate test work was performed to define the pellet chemistry and confirm the suitability of the magnetite to produce pellets suitable for the OneSteel blast furnace. A heating curve was developed by use of computer-based heat and mass balance modelling. Extensive pilot scale grate-kiln-cooler test work was then performed to confirm the heating curve and to verify and fine-tune the pellet properties. Computation fluid dynamics was used to design the physical changes to the furnace required to achieve the proposed heating curve.Following installation of an additional preheat zone, including a wall and dilution air fans, into the preheating furnace, and installation of an additional wall into the cooler, the modified furnace was commissioning in December 2007. The plant performed as expected during commissioning with the actual heating curve matching the proposed curve and the produced pellets within blast furnace specifications.

Jul 11, 2011

By C E. Loayza, R M. Pinto, J G. G=mez

The Yanacocha District is located 20 km north of the city of Cajamarca, in the Northern Andean Orogenic belt of northern Peru.Gold production may have occurred as early as Incan times (Paverd, 2000), but modern exploration that began in the 1960s targeted only copper and silver. Newmont Mining Corporation, BRGM and Compa±fa de Minas Buenaventura began exploring for gold in 1983, with Newmont as operator.Initial drilling took place in 1985. By 1992 a reserve of 1.28 million ounces was reported (Teal et al, 2002).Production began at the Carachugo deposit in 1993.Current reserves are 31.7 million ounces at $US 325 per ounce at a grade of 1.03 ppm (Newmont Annual Report, 2003).The operating company, Mineral Yanacocha SRL (Newmont 51 per cent, Buenaventura 44 per cent and International Finance Corporation five per cent) produced 2.85 million ounces in 2003, making Yanacocha one of the largest gold mining operations in the world. The district is made up of a series of epithermal, high sulfidation style gold deposits and one gold-rich gravel deposit (La Quinua), aligned in a NE trend.La Quinua is not discussed in detail in this paper. The bedrock deposits are hosted in a Miocene volcanic package, the Yanacocha Volcanic Complex that also trends NE.Re gional NW striking Andean faults intersect the NE striking Trans-Andean Chicama-Yanacocha structural corridor (Turner, 1997), localising the district mineralisation. These two structural orientations dominate the district, controlling breccia and intrusion locations, and gold mineralisation. Discontinuous EW oriented fracture zones are interpreted as extensional and locally are important in controlling gold mineralisation.

Jan 1, 2004

By C Li

Removal of gangue minerals from ilmenite concentrates can be accomplished by relatively low temperature roasting in controlled gas atmospheres to selectively enhance the magnetic separation characteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphere roasts were characterised by combining elemental analyses with quantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

By Ride G

The provision of a water supply is a major consideration in planning mining developments particularly in remote areas. The evaluation and development of adequate water supplies in and areas of Australia is often as important as the discovery of the orebody. The copper orebody at Warrego near Tennant Creek could not be mined economically if cheap treatment water was not available near the mine. This paper describes the difficulties in obtaining water in the Tennant Creek area and the water supply investigations carried out near the Warrego Mine which resulted in the successful discovery and evaluation of a reliable large scale water supply. It is contended that the establishment of a water supply must be approached on a systematic and scientific basis similar to the approach with the exploration and establishment of actual ore reserves. Mining companies with similar water supply problems may benefit by approaching their problem on this basis. The approach adopted by Peko Mines is outlined in this report.

Jan 1, 1980

By J A. Sanchidrián

The general ranges of validity of some distribution functions are assessed from their behaviour with 119 sets of fragmentation data from bench blasting obtained by sieving. The emphasis is on determining the lower size/passing limit that the size-scaled Rosin-Rammler, Grady and Swebrec functions, and their bi-component versions, can represent with reasonable precision. By fitting these functions to the data using different weights, the accuracy of the fit varies in the different size/passing zones, so that an overall knowledge of the capacity of the function is obtained across the whole size range, from the coarse zone to the fines. Reasonable ranges of use of bimodal Rosin-Rammler and extended Swebrec (all of them five-parameter, bi-component distributions) are, in terms of percentage passing p, 99 > p > 2 per cent (up to 100 per cent for the extended Swebrec), or 90 > p > 0.5 per cent, in which the expected error of the calculated size is below 15 per cent in the extremes of the range, and less than five per cent in most of the central range; maximum errors (ie errors that will only rarely be exceeded) are typically less than 50 per cent in the central range, and up to about 100 per cent in the extremes. Ranges of use for the Swebrec and the size-scaled Rosin-Rammler (three-parameter distributions), with only slightly larger errors than the bi-components, are 100 > p > 5 per cent or 80 > p > 2 per cent. The classical two-parameter Rosin-Rammler can be used in the range 95 > p > 20 per cent or 90 > p > 10 per cent, with expected and maximum errors less than about 15 per cent and 100 per cent respectively.CITATION:Sanchidrián, J A, 2015. Ranges of validity of some distribution functions for blast-fragmented rock, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 741–748 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G M. Hoffmann

Utilisation of lower grade (Jigging technology has progressed to a point where SishenÆs 50 to 60 per cent Fe run of mine (ROM) material, once considered as waste, can be beneficiated to produce a saleable 64 per cent Fe product. This has been confirmed through appropriate beneficiation testwork. Consequently, Sishen can now produce saleable product from material not currently included in the resource definition, significantly increasing the resource base of the mine and ensuring higher resource utilisation. Mine planning utilised the geological models to produce detailed planning schedules, reflecting the current and SEP plants separately, optimised to comply with product specifications of both the current and SEP plants and to confirm the viability of the low-grade resources identified as SEP feed material. The SEP product specifications have been derived by optimally matching iron ore market requirements with the revised resource base. A 64.0 per cent Fe lump product and a 63.5 per cent Fe fine product are the optimal SEP products. The SEP plant will be able to produce 10 Mtpa at an average yield of 60 per cent and a lump to fine ratio of 62:38. The plant consists of five major sections: namely crushing, material preparation, beneficiation, final product handling and quality control services. Maximum integration with the current Sishen plant was considered. Kumba currently has an agreement with Transnet to rail up to 23.5 Mtpa through the Sishen Saldanha iron ore export channel (IOEC). Transnet and Sishen Iron Ore Company have signed a Definitive Agreement that deals with the expansion of IOECÆs capacity, which increases KumbaÆs entitlement from 23.5 Mtpa to 35.0 Mtpa. The detailed enviro-legal impact assessments for the SEP indicated that the project has low enviro-legal risk as a result of it being a brownfields project incorporated into the current Sishen operations.

Jan 1, 2005

By James JV, Petho SZ

The South Deep surface shaft system is being sunk to a final depth of 2750 in below surface and on completion will be the deepest single drop haft in the world. The shafts will intersect the target reef horizon at 2650 to below surface. In order to negate the requirement for a shaft pillar, which would he extremely large at this depth, the reef horizon in the vicinity of the intersection is currently being mined. A high quality crushed waste/classified tailings backfill is being placed in the longwall stoping panels around the shaft intersection area. This kill limit closure and ride which following shaft reef intersection could have a detrimental effect on the long term shaft stability. This paper discusses underground instrumentation results and numerical modelling exercises carried out to confirm that the shaft system will he stable throughout the life of the mine. Instrumentation projects include closure and ride measured between backfill paddocks and haulage leveling exercises carried out to determine the far field rockmass response to mining with stiff backfill.

Jan 1, 1998

By H Cifuentes, D J. Williams

Despite the recognised importance of tailings management, there remain little data on the potential benefits of biological treatments compared with physical and chemical treatments. The operation of the majority of tailings storage facilities (TSFs) continues to employ mainly physical solutions, such as sub-aerial tailings slurry deposition, with increasing adoption of thickening, paste and filtration to dewater the tailings involving the addition of chemicals such as flocculants and coagulants. However, with tailings production continuing to escalate rapidly due to the increasing demand for commodities and reducing ore grades, available technologies have not demonstrated cost-effective performance at high tailings production rates. This paper examines the emerging role of bacteria to better manage tailings, reducing risks and optimising storage capacity. Bacteria have the potential to enhance tailings dewatering, maintain their permeability, delay the onset of desiccation cracking, and improve their shear strength. Bacteria-treated tailings may be suitable for use as construction materials. Bacteria also have potential in limiting the dusting of tailings and facilitating rehabilitation on closure. The paper describes a series of laboratory involving the addition of harmless bacteria to a range of tailings. The bacteria form a compact material called calcite (a common and stable form of calcium carbonate), which immobilises the tailings particles, releases water, and cements the tailings in a stable and natural matrix. The water released can be recovered or evaporated, depending on site objectives. The bacterial reactions are linked to physical and chemical processes, providing the potential for an optimal mix of technologies for particular tailings and site conditions.CITATION:Cifuentes, H and Williams, D J, 2018. Potential improvement of tailings geotechnical behaviour using bacteria, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 228–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

The influence of strongly chemisorbed solutes such as oxygen and sulphur on the rates of reactions at the gas-liquid iron interface is briefly reviewed. Deductions from recent studies of the rates of decarbur- ization of carbon-saturated liquid iron indicate ideal adsorption behaviour for sulphur over a wide temperature and composition range. This is in fair accord with available infor- mation on surface tensions in the Fe-C-S system. Previously unpublished results for the kinetics of the 14C02-CO exchange reaction are in accord with ideal absorption of oxygen on liquid iron. The derived value for the ideal adsorption coefficient of oxygen at 1550¦C is in quantitative agreement with measurements of the depression of surface tension in the Fe-0 system. Consideration is given to the applicability of such results to the violently agitated systems of steelmaking.

Jan 1, 1980

By R Dwyer

Iron ore currently mined in Australia generally requires very little beneficiation. However, depleting high-grade resources means that in the future low-grade iron ore deposits will need to be mined to meet the increasing demands of the global steel industry. Along with the increased demand, the industry faces additional pressure to reduce the environmental impact of mining and mineral processing. This has stimulated research beyond incremental improvements to conventional processing into alternative low-impact processes, including biotechnological approaches to mineral processing.Bioflotation and bioflocculation have emerged as relatively recent technologies, in which bacteria and/or their extracellular material may be used as flotation reagents (collectors or modifiers), enabling improved selective separation of minerals. The primary advantage is the production of a selective, environmentally-benign alternative to conventional flotation reagents. A biotechnological approach may also be taken in the beneficiation of high-phosphorous iron ores utilising bacteria capable of iron reduction and phosphorous solubilisation.Samples from three iron ore deposits in Western Australia were examined for bacteria suitable for iron ore benefi ciation. A number of common soil microorganisms including Pseudomonas spp, Limnobacter thiooxidans, Paenibacillus spp, and Ralstonia insidiosa were identified using culture-independent molecular techniques. A number of anaerobic species belonging to the genus Clostridium were also identified in the core samples. Selected aerobic species were enriched and isolated on high nutrient media in the presence of haematite. Several of the isolated strains showed an affinity for iron ore, attaching to haematite in enrichment cultures and further demonstrated through adhesion studies. Other isolated species such as Ralstonia isidiosa and Pseudomonas stutzeri are known to solubilise rock phosphates in soils and have potential for the removal of phosphorous from Australian iron ores.

Jul 11, 2011

By D Craw, C Smith, C Martin

The Wangaloa coal mine closed in 1989, and an attempt to grow Pinus radiata on quartz-rich overburden dumps was not successful. The site is currently being rehabilitated with re-profiling and native plant establishment. Plants are being established in a range of substrates that consist of variably disaggregated Tertiary coal measure sediments derived from the mine sequence. This material has low organic matter content (typically <10 %), originating from coal fines or carbonaceous sediment. Substrate samples were collected during December 2003 from a range of sites varying in age, slope, and parent material. Nutrient analysis includes nitrate, ammonia, total N, total P, available P and readily exchangeable base cations. Total nitrogen and phosphorus are low on areas of recently disturbed, quartz-rich overburden, with total N =1200 mg/kg, and total P =200 mg/kg. Background forested areas have total N ranging between 2800 - 3300 mg/kg and total P of 420 - 500 mg/kg. Quartz-rich overburden sites contain available nitrogen levels of less than 6 mg/kg, while background forested areas are generally >20 mg/kg. The soils and water runoff are generally acid, with pH down to three. Water samples have been collected from both ground and surface resources on a monthly basis since December 2003. The main lake on the site had pH of 4.6 in 1999, and this remained relatively unchanged when 850 tonnes of lime were added in 2002. However, the lake pH changed to 6.4 within a one month period in 2004, and has fluctuated since that time.

Jan 1, 2004

By Umetsu Y, Su Qing-quan

The electrical conductivity of electrolytes is very important in metal electrowinning and electrorefining processes as it has a very large influence on the energy consumption. There are few measurements of the electrical conductivity of zinc electrowinning electrolytes available. The electrical conductivity of zinc electrowinning electrolytes were measured over the following range of concentrations, 100 to 200 g/L H2SO4, 0 to 80 g/L Zn and 0 to 20 g/L Mg, at temperatures from 25 to 60 C. The specific conductivity of zinc electrowinning electrolytes may be expressed as a function of concentrations of sulphuric acid, zinc and magnesium and temperature by the following equation: k(S/cm) = 0.004 + 0.00115 t + 0.00282 [H2SO4] t - 0.00114 [M] t + 0.3442 [H2SO4] - 0.0451 [1-12SO4]2 - 0.1058 [M]ò[H2SO4] - 0.0224 (M] + 0.0286 [M] 2 where t is temperature (C), [H2S04](moI/L) is sulphuric acid concentration and [M](mol/L) is a sum of zinc and magnesium concentrations, ([Zn]+[Mg]). The specific conductivity of zinc electrolytes is a function of the concentrations of the hydrogen ion and free water molecule, which are calculated by taking into account the second ionisation constant of sulphuric acid and the stability- constants of zinc-sulphate and magnesium-sulphate complexes at 25 C.

Jan 1, 1993

By M W. Chen, I Canbulat, S Saydam, C G. Zhang

The height of fracturing (HoF) measures the propagation distance of continuous fracturing from the mining horizon and is also termed the height of cracking (Hebblewhite, 2020; Khanal et al, 2019) or hydrologically the height of groundwater drainage (Tammetta, 2013). In longwall practice, HoF is an important predictive indicator for assessing the dewatering effect of panel extraction on the shallow aquifer and surface flows. The HoF determination is basically dependent on field measurement works, typically using surface extensometer, borehole televiewer imaging, piezometer monitoring, packer testing, borehole breakout logging, and isotopic tracer monitoring (Brown and Walsh, 2022; Corbett, 2022; Hebblewhite, 2020; Holla and Armstrong, 1986; Mills and O’Grady, 1998; Walsh et al, 2022a, 2022b). These methods or tools have been widely applied to observe rock fracturing and groundwater responses to longwalls at Australian coalmines, for example, Dendrobium Mine (Brown and Walsh, 2022; Walsh et al, 2022b), Appin Mine (Walsh et al, 2022a), and Springvale Mine (Corbett, 2022). In Chinese mines, borehole televiewer imaging and packer testing are more frequently used due to convenient instrumentation, quick testing, and not requiring long-term maintenance of the instrumentation boreholes. The HoF determination also involves further raw data interpretations, for which specialist software for data extraction and quantitative criteria for bounding the fracture transition and termination are necessary. By combining the measured fracture distribution and longwall parameters regarding panel geometry and geological settings, several HoF models have been developed for conceptualising the understanding of strata depressurisation and providing mine engineers fast calculation tools for HoF prediction. The Mackie model considered the height of fracturing as the upper bound of fractured zone and revealed that within the fractured zone there are highly connected fractures and accordingly porosity enhancement and groundwater depressurisation, where the fracture network can be less transmissive from the mining horizon up (Hebblewhite, 2020). The fractured zone shares similar fracturing regime but different heights in varying models: HoF is 30 to 58 times of the mining height (t) based on Australian, Soviet and UK experience (Kendorski, 1993, 2006), and 21 to 33 t according to the field measurements in NSW Central Coast, Australia (Galvin, 2016). Some Australian longwall mines adopt Ditton model (Ditton and Merrick, 2014) (Equations 1.1 and 1.2 in Table 1) sourcing from NSW coalfield experience for HoF prediction, while Liu model (Liu, 1981) (Equations 2.1 to 2.4 in Table 1) developed from 27 coalmines in China is frequently used by Chinese coalmines.

Nov 29, 2022

By A Havenga, F, J Hough, R Grobbelaar

After the closure of mines they naturally start to fill up with water. As a result, hydraulic gradients develop between adjacent mines and different hydraulic water pressures are exerted onto peripheral areas or compartments within mines. This results in water flow between mines, or onto the surface. This flow is referred to as intermine flow. The geometry of the collieries in the central Witbank Coalfield make intermine flow possible in several areas. Since the Department of Water Affairs and Forestry declared intermine flow as one of its greatest concerns for granting closure to South African mines, much research into this phenomenon has been undertaken. The importance of the quantification lies in the DepartmentÆs goal of sustainable water management, and the possible long-term financial implications these flows could have for individual mines. The challenges of determining intermine flow are numerous, and attention is focused on the identification of areas where these flows can take place. Detailed mining plans on a regional scale are required, and detailed coal-seam floor data are combined to provide targets for possible interaction between these mines. The quantification of these flows is problematic due to the uncertainties regarding geometrical configurations and the variation in site-specific hydraulic characteristics of the coal and overlying lithilogical layers. To this end, use has been made of several analytic solutions and numerical flow modelling. Stage curves (volume versus elevation curves) for the opencast and underground workings have been calculated and first-order estimates for intermine flow or decant from these areas have been determined. The numerical modelling methodology entailed a down-scaling approach, starting with a broad regional model covering the entire area, followed by modelling the interactions between interconnected mines and finally looking in detail at the major areas of interaction. By considering different scenarios within the context of these flows, possible management options for intermine flow can be evaluated in terms of volumes and qualities that might emanate in the post-closure phases. Challenges for the future include obtaining site-specific information on the groundwater hydraulics and acceptable ranges for model parameters, and verifying model results over time.

Jan 1, 2003

By K Knorr

Desktop X-ray powder diffraction using a D2 PHASER equipped with fast linear detector was performed on several iron ore and mill scale samples. Data were analysed using cluster analysis and Rietveld quantitative phase analysis. The quantitative mineralogy of both materials could be established. Thus the input is provided for understanding the energy consumption and the CO2 emission during iron production. Furthermore, tabletop XRD allows to distinguish iron ore from mill scales and to quantify their mixtures.

Jul 11, 2011