Search Documents

By C. W. Beattie, R. L. Solter

ALUMINUM-KILLED, low carbon steel sheets are used extensively for severe deep drawing and other difficult forming operations. They usually, but not always, have a characteristic grain structure in which the grains are elongated both in the lengthwise and in the transverse direction. As described by Burns and McCabe,&apos; a typical grain in the plane of the sheet has its two axes in that plane from 1 Y2 to 4 times as long as the axis normal to the plane of the sheet. Rickett, Kalin, and MacKenzieZ have also reported on the recrystallization behavior of such steel. The contrast in grain structures of fully processed sheets of aluminum-killed and rimmed steel is illustrated by Figs. 1 and 2. The elongated grain structure of the aluminum-killed sheet is not developed on all heats or lots of this metal, and studies of the factors controlling and influencing its formation are reported in this paper. Jeffries and Archerb tate that unstrained grains are normally equiaxed, but exceptions are common. For example, if a metal containing a material mechanically obstructing grain growth is subjected to considerable working followed by thorough annealing, it may exhibit grains consistently elongated in the direction of working. Our experiments demonstrate that aluminum-killed, low carbon steel is such a metal, and that the substance mechanically obstructing grain growth is aluminum nitride. The effectiveness of aluminum nitride in inhibiting grain growth has been found to be influenced by the degree of cold reduction, the rate of heating in annealing, the thermal history of the sample before cold reduction, and the residual aluminum content. A correlation between grain shape and austenitic grain coarsening temperature also was indicated and additional experiments demonstrated that aluminum nitride is also the principal cause for the fine grain characteristic of aluminum-killed steels. Manufacture In conventional practice, aluminum-killed sheet steel is manufactured from a low carbon steel containing approximately 0.02 to 0.07 pct residual (HC1 soluble) Al. With the exception of certain samples containing greater or lesser amounts of aluminum, the steels used in these investigations were within the following composition range: C, 0.03 to 0.06 pct; Mn, 0.28 to 0.38; S, 0.017 to 0.032; Al, 0.03 to 0.06; P, <0.01; and Si, <0.01. Properly heated ingots are rolled to slabs about 4 in. thick. After surface conditioning, the slabs are reheated to about 2300°F and hot rolled continuouslv to strip about 1/10 in. thick. The strip rolling is completed at a temperature of 1550°F or higher, and the strip is coiled, usually at a temperature near the lower critical transformation. After cooling, the strip is pickled to remove oxide, cold reduced 40 to 70 pet to final thickness, then annealed to 1250° to 1350°F in 20 to 80 ton charges, the size of which results in slow heating and cooling rates. Effect of Cold Reduction According to Sachs and Van Horn,&apos; the deformations of the individual grains in rolling are similar to those of the total volume. Thus individual grains would elongate in rolling according to the amount of cold reduction imposed. This is true theoretically, but as cold reduction increases the individual grains tend to fragment, and measured grain elongations become less than theoretical. The amount of grain elongation may be described by a numerical rating based on grain counts made by the intercept method. Specimens are polished normal to the plane of the sheet, with the polished surface extending parallel to the rolling direction. After etching, grain intercepts are counted along a 50 mm line on a micrograph of suitable magnification. In random locations parallel to the plane of the sample 20 counts are made and 20 are made in the thickness direction of the sample the average count in the thickness direction divided by the average count parallel to the plane of the sample gives a numerical rating of the grain shape called grain elongation. For example, a grain elongation of 2.00 means that the average grain is twice as long as it is thick. The average of both counts may be converted to grains per sq mm by a nomograph relating intercept counts and grain count. By the same procedure the grain elongation in the plane of the sheet but transverse to the rolling direction may be determined, using transverse metallographic samples. A comparison of theoretical and measured grain elongation was obtained on an aluminum-killed

Jan 1, 1952

By C. H. Keplinger

WARTIME factors have strengthened the production engineering consciousness of the petroleum industry. The basic principles of sound oil-production technology have been accepted as the standard by the industry and the governmental co-ordinating agencies. Every effort is being made to furnish larger quantities of petroleum with a minimum expenditure of materials and under strict conservation practices. The sphere of influence of production engineering extends from fundamental reservoir control of withdrawal rates and reservoir pressures to bolstering production from stripper wells. Serious transportation difficulties in moving oil to the East Coast have stimulated secondary recovery operations in the Appalachian and East Central oil-producing states. Diminishing discovery of new oil reserves by exploration activities increases the importance of promoting efficient oil-producing methods and practices throughout all productive areas in the United Nations.

Jan 1, 1943

By R. L. Braun, D. L. Leach

Laboratory experiments simulating in-situ copper recovery from primary sulfide ores in sulfuric acid systems pressurized with oxygen are reported. Copper extraction and acid consumption data are correlated with temperature in the range 50 to 150°C and quenched pH in the range 0.25 to 2. Adverse changes in the chemical composition of the leach solution and the formation of gangue-mineral alteration products and secondary sulfides can severely limit the extraction of copper above 90°C. Keeping the pH below the self-buffered value of about 2 and the temperature below about 110°C produces the maximum extraction rates. Forcing the pH too low not only results in excessively high acid consumption but may also limit the extraction of copper at temperatures above 100°C.

Jan 1, 1977

By Bjorge, Guy N.

MINING method improve through the gradual process of evolution and in 1340 there were no marked outstanding innovations. On the other hand refinements of detail and betterment: in equipment design continued to progress. Among the most important changes have been the increased application of trucks and highway equipment, including tractors and bull- dozers, to open-pit mining as exemplified by Phelps Dodge&apos;s Morenci operations; the Mesabi iron range; and the Tri-State district. Mass or bulk handling contributed its part underground with slurhers and conveyors at Consolidated Coppermines and slushers at Climax; and in open-pit mining. conveyors found increased use on the Mesabi range.

Jan 1, 1941

By M. D. Curran

AS applied to coal, the term processing is subject to many interpretations. To some it means preparation of coal for the market by mechanical means such as crushing, sizing, washing, or treating with oil or chemicals to eliminate dust or improve combustion quality. To others it means conversion of the coal to other commodities as in carbonization to produce coke and by- products, or to liquids by application of the hydrogenation process. I prefer to classify the various forms of mechanical treatment under the heading of beneficiation and apply the term processing to those methods of treatment that destroy the coal sub- stance through distillation or hydrogenation.

Jan 1, 1939

• Pellets of concentrated iron ore have been smelted in the blast furnace by Armco and the results proved satisfactory. Various percentages of pellet burdens were tried and it has been found that charges up to 70 pct pellets are workable. •In the reorganization of the Department of the Interior, two new assistant secretaries were appointed and the work divided between the four assistant secretaries. C. Girard Davidson will head a division of mineral resources including the Bureau of Mines, Geological Survey, Division of Oil and Gas and Division of Geography. •Germanium, one of the rarest of metals and a wartime strategic material, has been discovered almost in the shadow of the Capitol. The only catch is that the scattered nature of the deposits makes profitable recovery extremely doubtful. Nevertheless, experts have tabbed the concentration in the District of Columbia area the world&apos;s second richest known concentration of the element. • Cakes of mica, weighing up to 500 lb, have been formed at the Colorado School of Mines by a new "cool hearth" method. The process avoids use of crucibles and contains the molten mica in a basin of unmelted raw mixture from which the melt was derived. Crystallization takes place in this melting basin which forms a center pool surrounded by a solid cool mass of the unmelted raw mixture. • William 1. Baxter, of the International Economic Research Bureau, predicts a period of deflation because of war-essential restrictions on consumer credit and materials use. He stated; "the recent prosperity was based mainly on the sales boom in autos, homes, and household accessories." •Two subsidiaries of United States Steel have decided to build four new ships immediately to augment iron ore and limestone carrying capacity on the Great Lakes to meet demands created by the national defense emergency. •The Norfolk and Western Railway is making a complete change over to coal to drive its locomotives. •A national roster of scientific personnel similar to the one used in the last war will be established by the Office of Education, by agreement with the National Security Resources Board. The new unit, the National Scientific Register Project, will make studies of the Nation&apos;s scientific manpower supply and recommend steps to increase the numbers of skilled personnel where needed. •National Lead Co. will start construction immediately of new facilities at St. Louis, Mo., for production of titanium pigments for paints. Producers of titanium pigments have been under considerable pressure to meet all demands from paint manufacturers, particularly for titanium dioxide. •The basic criteria for deferment of reservists in civilian occupations are (1) the Department of Labor List of Critical Occupations, and (2) the Department of Commerce List of Essential Activities, both of which were announced Aug. 3. Fundamentally, the reservist deferred must be engaged in a critical occupation which is necessary to a highly essential activity, and he will be deferred only until he can be satisfactorily replaced in that occupation. A delay in call to active duty, it was emphasized, may not be considered as an indefinite exemption from military service.

Jan 9, 1950

By B. H. Bergstrom, A. P. Cohen, D. W. Fuerstenau

B.H. Bergstrorn (Research Div., Allis-Chalmers Mfg. Co., Milwaukee, Wis.) — Fuerstenau and Cohen have concluded from our study of single particle crushing, which had suggested that the size moduli of the crushed specimens were determined by the specific energy expended independent of feed size, that the same independence with respect to feed size exists for the specific energy-product size relationship for rod mills. They present data supporting this conclusion. Our single particle crushing experiments were on single spheres of soda-lime (type of glass was not given in our study) glass for which the feed size can truly be neglected. However, the feed size cannot be neglected in any case where the effective size modulus of the feed is not too much coarser than the size modulus of the product. This can be illustrated in the second experi- ment of Fuerstenau and Cohen where the feed is considered to be the original -6 +%mesh material. However, one can also consider the product from the 7.5-min grind to be the feed for the 10, 15, 20, 25-min grinds, and the 10-min product to be the feed for the 15, 20, 25-min grinds, etc. If the specific energy-product size moduli curves are drawn for these other feeds, as shown on Fig. 3, the new curves (and some curvature is apparent) are much steeper than the -6 +%mesh feed line. The slopes of these new curves are about -1.5, —1.8 and -3.0. This observation is in accord with the observation by Bond, who states that the net specific energy input to a grinding mill is equal to the specific energy represented by the product less the specific energy represented by the feed. Bond presents, on a diagram similar to Fig. 3, a series of curves which illustrate the effect of

Jan 1, 1963

By B. O. Pickard

WITH more than a score of shafts and numerous stope openings to the surface, all inter-connected underground; with underground temperatures high, often exceeding 100° wet bulb; with an ore presenting a dust health-hazard; with certain rocks giving off inert gases; with an altitude of 6000 ft. above the sea level and a dry desert climate, the Tonopah mines offered an interesting, problem to the student of metal-mine ventilation. Tonopah is not an old mining district relatively speaking. It was discovered in 1900 and Tonopah soon was a boom camp. By 1910 the mines of this district had paid many millions of dollars in dividends. At the time of the 1921 ventilation study, mining had passed its peak of production and the operators were striving to reduce costs, to discover new ore bodies, and to attract desirable workmen. In 1925, the camp was operating on a still less prosperous basis, but the several managements had not relaxed in their efforts to keep the mines on a paying basis, neither had they lost their faith in the ability of the mines and the price of the silver to "come back." Early in the fall of 1921 the Bureau of Mines was invited by the mine operators at Tonopah, Nevada, to make a detailed study of the under-ground air conditions in the Tonopah silver district. D. Harrington,? who was then directly supervising the ventilation studies of the bureau, detailed district engineer B. 0. Pickard, mining engineer E. D. Gardner, surgeon C. E. Kindall, and petrographer H. Insley to carry on the study. G. S. Rice, as chief mining engineer of the Bureau of Mines, was in general charge of the work. Upon the completion of the study each operator was furnished a report on conditions in his mine.

Jan 2, 1927

By G. M. Ritcey

Sulphuric acid leaching has been up to the present, the most popular of the leaching routes. Oxide ores are usually leached with sulphuric acid directly by dump leaching, as practiced at the Bagdad or Bluebird Mines in Arizona, or by vat leaching as done at Inspiration Mining in Arizona. Upgrading of the low-grade oxide ores by dump leaching followed by cementation of the copper from solution by scrap iron has been replaced by the leaching-solvent extraction-electrowinning route which results in a high purity product at the mill site at reduced production costs compared to previous practice. High-grade oxide ores, vat leached with H2SO4, can contain, for example, 25 g Cu/l and 25 g H2S04/,l, or higher concentrations of both, and are presently fed directly to electrorefining plants. Advantages of coupling solvent extraction-electrowinning with the low cost dump leaching instead of using cementation, are as follows (1): a) the production of high purity electrolytic copper rather than cement copper;

Jan 1, 1978

By Donald H. McLaughlin

THE activity and enthusiasm of pioneers still prevail among workers in applied geophysics1.- Within the year, new devices have .been tried out, instruments and technique have been improved and the methods of application to commercial problems have been increased in many ingenious ways. There is still great need for more skillful interpretation of results in terms of geology, but oil the whole geophysical prospecting is making encouraging progress toward finding its proper place and function in engineering and geological practice. Spectacular successes continue to be reported, particularly .from the Gulf Coast, where the race for salt domes has not slackened, and encouraging results have been giined elsewhere in the mapping of structures in the search for oil. In the mining field, however, it can hardly be claimed that the same measure of success has been obtained, for brilliant efforts worthy of wide recognition have been overshadowed to some eatent by the unfortunate outcome of surveys undertaken unwisely without recognition of the limitations of the work. Consequently, hopes were aroused that could not be fulfilled, and it must be admitted in an impartial survey that there are a few regions, chiefly in the far north, where the standing of geophysical prospecting is somewhat doubtful and where the course of public opinion regarding it shows a certain similarity to the history of the market during the past few months. Reliable work, however, is steadily going 011 and it can confidently be expected that the methods will eventually be regarded in many regions as an essential part of the technique of securing geologic data needed for intelligent exploration.

Jan 1, 1930

By G. A. Swanquist, E. M. Morales

INTRODUCTION The idea of water management and control at the Church Rock Mill operations began to take shape in February 1979. At that time, we were already investigating the feasibility of decreasing the fresh water requirements so that the solids would become the limiting factor in tailings impoundment utilization. The area for solution evaporation could be kept at a fraction of the normal requirements under the standard process of full water usage. The Church Rock Mill is an acid leach circuit followed by solids/liquid separation with thickeners in counter current decantation, and solvent extraction. Following the normal design of acid leach circuits, reuse of tailings solution was not incorporated in the original mill process design. INITIAL WATER CONTROL INVESTIGATIONS The investigations to decrease the fresh water requirements centered around modifying the grinding circuit from the present semi-autogenous grinding (SAG) mill in closed circuit with hydrocyclones, to open circuit grinding with a rod mill. The open circuit grinding with the SAG mill and rod mill in series had the potential of decreasing the water requirements for grinding and leach dilution by approximately 50% or 1.4 m3/min (300 gpm). The grinding pulp density would be maintained at 70 to 72% solids, and the leach dilution to 50% solids would be accomplished with acid tailings liquor recycle. In such a grinding circuit arrangement, the SAG mill would provide the primary or coarse grind, and the rod mill would be used for the fine grind. By the SAG mill and rod mill series grinding method of water control and other secondary water controls in various places downstream from the grinding circuit, the required necessary evaporation area was estimated at 120 acres of liquid surface. A second method of water control at grinding was investigated. A two-stage cyclone classification circuit appeared to have a good potential of achieving the same water reduction at a much lower capital and operating cost. However, in retrospect, this would not have been a viable method since a high slime recycle load would have been established hindering classification. The use of reagents to neutralize the acid tailings solution was not considered seriously at that time, since it would have materially increased operating costs, although it would have also allowed more tailings solution recycle and consequently, less fresh water usage. However, with the tailings solution deposition area available at that time, it was not then necessary to incur the high cost of neutralization. The control expected by the series grinding of semiautogenous and rod mills would have been sufficient to maintain a water consumption/evaporation equilibrium well in line with the available land area. IMPLEMENTATION OF NEUTRALIZATION OPERATIONS During the summer of 1979, the UNC Church Rock Mill experienced a tailings dam breach which resulted in a prolonged mill shutdown. Upon resumption of operations at the end of October 1979, tailings deposition was restricted to a small portion of the tailings impoundment area. Figure 1 shows the general tailings area and the limits of the present deposition area in the central part including the borrow pits. These borrow pits had been excavated to provide materials for tailings dam construction. Immediately after resumption of operations, it became evident that it would be necessary to control the quantity of liquid to be evaporated because of the small confined area available for tailings solution deposition and to maximize the deposition time in the tailings area. The water control required had to be exercised on a large scale, and to be in operation as quickly as possible. An obvious solution was to reuse the tailings liquor in mill process. Immediate steps were taken to install the necessary equipment for tailings neutralization on an interim basis. Anhydrous ammonia was selected as the primary neutralization reagent since it was the quickest system that could be placed in operation. Previous laboratory tests indicated fair results with ammonia neutralization. Such a system required a minimum of installed equipment and handling. INITIAL NEUTRALIZATION OPERATIONS Actual neutralization operations began on November 26, 1979. The raffinate solution which normally would have been discarded was pumped to a 3.7 m (12ft) diam by 4.3 m (14ft) tank for reagent contact, see Figure 2. At this tank, anhydrous ammonia was added directly from the tanker trailers and controlled at pH 7.0 nominally. Agitation was provided by air sparging. The neutralized product formed a highly viscous slurry in the grinding circuit which resulted in pumping and cyclone classification problems.

Jan 1, 1982

By Jan H. Hommen

TRENDS IN MINE FINANCE Reviewing historical trends may help in dealing with future funding strategies. The first trend is the increase in the use of debt to fund corporate America. Surprisingly, when comparing that with other corporates in the global marketplace, the U.S. does not look too poorly. Japanese, in particular, but also German companies, are much more leveraged than their U.S. counterparts. Note that in Japan and Germany the government and the consumer have shown substantial restraints when it comes to credit. Not so in the U.S. where the savings rate (4%) is much lower than that in Japan (20%) and in Germany (14%). As a result, the cost of leverage is substantially lower in Japan and in Germany than in the U.S. Lower debt costs in these countries allows one to obtain more of it for the same price. The close relationships between financial institutions, corporations and governments in Japan and Germany also make the risk of leverage more bearable and understandable. Also note that interest rate volatility in these countries is more subdued. The investor base in common stock is also changing. Private pension funds have been net sellers of equities during the last few years while public pension funds have been net buyers. Individuals are basically out of the market. It is estimated that over $330 billion of equity was retired in the U.S. through 1986-1988. The reasons are well known: restructurings, buy-backs, takeovers, mergers, and buy-outs. This de-equitization is likely to continue as the cost of equity capital is higher than the cost of debt capital, even on a before-tax basis. Because there has been no market for equity since October 19, 1987, junk bonds have replaced equity capital in the corporate finance structure. The non-investor-grade borrower has access to the public markets through high-yielding debt securities that often look like senior equity. Deregulation has also provided 24-hour markets; securitization can now liquify assets that before were rusting on balance sheets; information processing and communication tools give facts that are instantaneously available, creating the need for products to cover risk and exposures unknown before the start of the information and technology explosion. Thus we now have swaps, options, futures, options on futures, caps, as well as program trading, portfolio insurance, index funds, etc. Globalization will be unstoppable. Today&apos;s environment demands it. Corporations are now global competitors, even though they may have never shipped a product off-shore. Boundaries are disappearing and impediments have been removed. Stocks can be issued in a global offering with distribution in all major financial centers of the world. The high leverage of Japanese companies has made common stocks very scarce, which with the high savings rate, makes equity capital inexpensive in Japan. If markets were perfect everyone would issue stock in Tokyo and buy it back in New York. This would certainly stop the bleeding on the balance of payments. With the deficit balance of payments in America, it is no surprise that the cost of money is expensive here. The risk-return relationship on U.S. equity is not favorable enough to appeal to Japanese equity investors. The Tokyo-market, helped by a stronger yen, surpassed New York as the most important equity market in the world. The question is, will the Tokyo market hold up when Japanese domestic consumption increases at the expense of savings? In the U.S. debt markets, the plain vanilla debenture is making a comeback after a period of absence. Commercial paper has replaced short term bank borrowings for working capital funding by larger corporations. The banks have made an interesting comeback with loan sale programs that will continue to attract borrowers. There will be a continuing

Jan 1, 1990

By AIME AIME

LEWIS EMANUEL YOUNG was elected a Director of the A.I.M.E. at the last Annual Meeting as a representative of District &apos;4, including. Ohio, West Virginia, and western. Pennsylvania and New York. He also represents the Coal Division, in which industry lie has actively participated- for nearly twenty years. Dr. Young was horn in Topeka, Kan., Oct. 1, 1873, received mining degrees from Penn State and ,-Iowa. State, and a Ph.D., from Illinois. The first part of his professional life was spent in teaching first as instructor in mining at Iowa State, second .as professor of mining at the Colorado School&apos; of Mines, third as director of the School of Mines and Metallurgy at Rolla, Mo., and finally he taught business

Jan 1, 1937

By J. Stuart Warner

The reaction COSO4(c)?CoO(c) + So3(g)was investigated from 950° to 1170OK by two different methods. The sulfate was decomposed in a previously evacuated space and Pso3 calculated from the measured total pressure on the assumption that Pso2 = 2P02. The sulfate was also decomposed under conditions of controlled oxygen pressure. The difference in the results obtained by these experimental techniques is attributed to the effects of thermal diffusion. The standard free energy change for the reaction is given by ?F° = 66,292 + 17.273T log T — 102.57 T (±300 cal/mole). It was found by DTA and X-ray diffraction studies that CoS04 undergoes a transformation at 617°± 4°C. THE metal sulfates may decompose directly to the oxide or pass through one or more intermediate basic sulfates. Provided the oxidation state of the cation does not change in the course of the reaction, the decompositions may be described in general as follows: One of the major objectives of this work was to determine the validity of Eq. [3] as much of the existing sulfate data has been calculated from decomposition pressures by Eq. [5]. The type of apparatus generally used for these measurements consists of a reaction vessel at high temperature which communicates with a manometer at room temperature. A temperature gradient is thus imposed on the gas phase causing thermal diffusion which brings about a partial separation of the different gaseous species present in an initially uniform mixture. The basic theory and experimental facts associated with this phenomenon are summarized elsewhere1 and it will suffice to state here that the heavier gaseous species diffuses down the temperature gradient. Since thermal diffusion destroys the homogeneity of the gas phase, it is not necessarily true that Pso2 = 2Po2 in any particular volume element of the gas phase even though there are twice as many molecules of SO, as of 0, in the gas phase considered as a whole. Under these conditions, the decomposing sulfate gives off SO, which dissociates to SO, and 0, and all three species are distributed throughout the system by thermal diffusion. However, the sulfate will continue to dissociate until the equilibrium value of PSo3 is established on the hot zone. Thermal diffusion may distribute SO2 and O2 throughout the gas phase in any way so long as Eq. [2b] is satisfied in the hot zone; i.e. Pso2(Po2)1/2=K3pso3. When a steady state is reached, we can characterize Pso2 in that

Jan 1, 1962

By A. K. Chakravarti, A. Lihiri, G. G. Sarkar

One primary objective of India&apos;s third Five Year Plan is the expansion of coal production. The goal: boost present output of 45 million tons to 95 million tons by 1965--an increase of more than 100 pct!

Jan 7, 1961

By William N. Poundstone

What attracts young engineering graduates into the coal industry? What do these young men expect of a career in coal mining? These questions are often asked and debated by mining men throughout the country. In order to present a comprehensive answer to them, an opinion survey was conducted at West Virginia University&apos;s School of Mines among the junior and senior classes and part of the sophomore class. The tabulation of the answers showed that the present-day mining engineering student is an older, more mature individual as compared with former years and as compared with other present-day college students. The average age of the country&apos;s record-breaking 150,000 college graduates is 24 years. Among this year&apos;s mining graduates at West Virginia University, 78% are of this age or older. Over half (54%) of those polled in the survey are married. This is com- pared to 30% as a national figure. Of those married, 38% have one child and over 6% have two children. The entire senior group covered by this survey has averaged almost three years in the armed forces. An article entitled "The Class of &apos;49" in the June issue of Fortune magazine states that this year&apos;s class is the oldest, most mature class in history. Our survey indicates that the mining engineering students at West Virginia University are well above the average in this respect.

Jan 1, 1949

By J. E. Burke, A. M. Turkalo

IN 1923 Desch¹ pointed out that the grains in a metal which is anisotropic with respect to its thermal coefficient of expansion would contract differently upon cooling, and that the stresses developed might approximate the plastic strength of the metal. More recently Boas and Honeycombe2-5 studied the behavior of several metals upon thermal cycling and observed that the stresses developed in arlisotropic metals are great enough to produce slip lines in individual grains and a roughening of the specimen surface. This phenomenon they have named "thermal fatigue." The mechanism they propose involves essentially a kneading of the grains, the deformation being alternately in compression and tension in a given grain as the temperature is changed in one direction and then the other. The present work was undertaken to investigate the possibility that an additional mechanism might operate to produce plastic deformation during thermal cycling—a "thermal ratchet" that depends upon a combination of grain boundary flow to relax the stress that develops between differently oriented grains upon raising the temperature and transcrys-talline slip to relax the oppositely directed stress which develops on lowering the temperature. Thus, thermal cycling should produce a nonreversible distortion such that certain grains will change shape differently from their neighbors with a simultaneous displacement being produced at the grain boundary. Temperature Dependence of Grain Boundary and Grain Strength The critical resolved stress for the initiation of slip in metal grains is only mildly affected by temperature." For example, in cadmium it decreases from 0.15 to about 0.05 kg per sq mm when the temperature is increased from 20° to 458°K and further temperature increase causes little further decrease. On the other hand, the work of KG1 indicates that the grain boundaries behave in a viscous fashion that can be described8 by the expression: t = BVexp(Q/RT) [1] t is the shearing stress on the boundary; B, a constant; V, the flow rate at the boundary; Q, the activation energy for grain boundary flow; R, the gas law&apos;s constant; and T, the absolute temperature. Eq 1 indicates that the stress necessary to cause a given grain boundary flow rate, V, decreases rapidly with increasing temperature. The value of the constant B is such that at sufficiently low temperature and ordinary strain rates deformation will occur preferentially by slip rather than by grain boundary flow. There is considerable evidence to indicate Consider the bicrystal shown in Fig. 1. In grain 1 the slip plane lies 45 " to the boundary while in grain 2 the slip plane is 90" to the boundary. The coefficients of expansion of the grains in a direction parallel to the length of the crystal are a1 and a, with a, > a2 for the orientations shown. The sequence of events that can occur upon heating and cooling this specimen is illustrated schematically in Fig. 2. Initially there is assumed to be no stress in the specimen (A). Upon heating, grain 1 attempts to become longer than grain 2, but is constrained by grain 2. Thus grain 1 is loaded in compression and grain 2 is loaded in tension, and a shearing stress is present across the boundary (B). As the temperature is increased, the stress will build up, and finally grain 1 will be plastically deformed by slip, since the greater stress is resolved on its slip planes. Any further heating will result in more slip and the stress will remain constant until some temperature T* is reached where the stress can be relaxed by grain boundary flow.† At this relaxation temperature (C) a step will appear between grain 1 and grain 2. Further heating above T* will cause grain 1 to become relatively longer, but no stress will appear because the grain boundary is too weak to support the stress (D). Upon cooling again, at T* (E), the grain boundary will again be able to support a shearing stress, and upon cooling further, grain 1 will be loaded in tension and grain 2 in compression (F). When the decrease in temperature below T* is sufficient to impose the critical shear stress upon the slip plane of grain 1, it will be stretched by slip.

Jan 1, 1953

By J. Ehner Thomas, M. D. Gould

Until four years ago the market price of oil securities moved directly and immediately with the general list. This point, was first developed by the senior author in 1924 while making a statistical study of the relative movement of oil securities and the general market. Plotting the monthly averages of 17 oils against 233 industrials disclosed the sur- prising relationship shown in Fig. 1. The traditional vagaries of the oil business, the wide fluctuations in current supply and resulting abrupt changes in crude prices nevertheless produced no movements in the market price of oil securities as a group, which departed notably from the movements of the general market. Obviously general business conditions did not always change when and as conditions in the oil industry changed; clearly the fluctuations of

Jan 1, 1929

By L. E. Young

MUCH has been said and written on this subject and probably little new can be said. However, the point of view of the operating company changes from time to time, and more stress may be laid upon a subject today than was done some years ago, and it is with this changing point of view that the following observations are presented: The writer wishes to limit the discussion to views of a company mining bituminous coal, particularly to what the production department expects of the college grad¬uate. In an editorial in MINING AND METALLURGY for February, 1929, entitled "Is. Mining Engineering Passing?" it is stated that: It is not by accident that mining engineering courses have been general rather than special and form even today the only general engineering courses widely offered and followed by engineering students.&apos;* * * even in this age of specialization, the mining engineers remain a body characterized particularly by broad knowledge.

Jan 1, 1929

By William L. Fink, Kent R. Van Horn

Zinc is one of the effective elements introduced to enhance the strength of aluminum. This strengthening is principally attributable to the high solid solubility of zinc in aluminum and the pronounced variation of solubility with temperature. Consequently an accurate determination of the solid solubility curve is desirable. The solid solubility relations have been studied by numerous investigators. Shepherd1 first established the existence of a solid solution region at the aluminum end of the diagram (-v phase) by specific volume and microscopic determinations. Bauer and Voge12 published a constitutional diagram which showed the limits of solid solubility as determined by thermal and microscopic methods. Hanson and Gayler3 presented the aluminum-zinc diagram which is now most generally accepted (Fig. 1). Chill-cast samples were given thermal treatments designed to obtain equilibrium conditions, quenched, and microscopically examined. The solubility was placed between 15 to 20 per cent at 60" C., 20 to 22 per cent at 140" C. and 36 to 38 per cent at 270" C. Sander and Meissner decidedly modified the limits of the -y phase field of Hanson and Gayler&apos;s diagram by using similar methods on chill-cast specimens annealed for a shorter period of time. Tanabe,s utilizing dynamic hard-ness, electrical conductivity and dilatometric measurements of specimens at temperature, obtained values comparable to Hanson and Gayler&apos;s at room temperature, but appreciably lower at higher temperatures. Nishimura6 concluded from age-hardening results of aluminum-zinc alloy chill castings, which had been quenched from 400" to 500" C., that the solubility of zinc in aluminum at room temperature is less than 5 * Metallurgical Division, Aluminum Research Laboratories. 1 E. S. Shepherd: Aluminum-Zinc Alloys, Jnl, phys. Chem. (1905) 9, 504. 2 0. Bauer and 0. Vogel: Aluminum-Zinc Alloys, Int. Jn1. Melallog. (1916) 8, 101. 3 D. Hanson and M. V. L. Gayler: A Further Study of the Alloys of Aluminum and Zinc. Jnl. Inst. Met. (1922) 27, 267. 4 W. Sander and K. L. Meissner: ZII~ Kenntnis der Konstitution der Aluminium-Zinklegierungen. Ztsch. f. Metallkunde (1922) 14, 385. 4 T. Tanabe: Studies in the Aluminum-Zinc System, Jnl. Inst. Met. (1924) 32, 415 6 H. Nishimura: On the Age-Hardening of Aluminum-Rich Al-Zn Alloys. Mem. Kyoto Imp. Univ. (1924) 3, 133.

Jan 1, 1932