Search Documents

By Carlos Alberto Mourão, Robson Martins, Letícia Madureira Moreira, Hélio Braz Loss, Joilson Moreira Ferreira da Silva, Edilson Simões Cavalieri, Mauricio Ferreira Coelho

O conversor AOD-L é de uso exclusivo para a produção de aços inoxidáveis na Aperam South America. Entre janeiro a julho de 2018, o consumo de FeSi estava acima do orçado, acarretando em perda de gestão para a Aciaria. O aço inoxidável AISI 304 representa 50% da produção da Aciaria na rota duplex (sem uso do VOD), portanto, esse projeto teve como objetivo a redução do consumo da liga de FeSi no AOD-L para o aço AISI 304. Essa redução foi possível através da utilização da metodologia Lean Six Sigma na qual a causa raiz foi identificada e as ações implementadas o que permitiu uma maior estabilidade operacional, além de aumentar a competitividade da Aperam South America frente aos demais produtores mundiais.

Oct 1, 2019

By Túlio Magno Fuzessy de Melo, Luciano Santos Marques, Vicente Tadeu Lopes Buono

The influence of the coiling temperature after hot strip rolling on the microstructure and on the tensile and hole expansion properties of a 800 MPa multiphase steel was investigated. For the temperatures between 150°C and 600°C the microstructure consisted of a ferritic matrix with a dispersion of fine martensite-austenite (MA) and regions of degenerated upper bainite. In all cases the ferrite presented a heterogeneous mixture of polygonal, quasi-polygonal and acicular grains. The yield and tensile strengths showed a tendency of decreasing with the increasing coiling temperature, probably because of the larger fraction of MA particles at lower temperatures and higher fraction of quasi-polygonal ferrite at higher temperatures. The elongation was not significantly affected by the variation of coiling temperature. The average hole expansion ratio showed a maximum of 80% for the material coiled at 400°C and fell below 50% only for the coiling temperature of 150°C, probably due to the larger hardness difference between the ferrite matrix and the MA particles.

Oct 1, 2019

By Walmir Pereira de Amorim Junior

Imersas em um mercado em constante mudança, as empresas têm seguido em uma busca contínua pela melhoria de seus processos. Diante disso, nos últimos 2 anos, o segmento de Aços Planos da ArcelorMittal Brasil vem passando por um processo de transformação, revisitando e reestruturando seus processos internos. Na área de planejamento um dos itens avaliados foi o processo de Planejamento de Vendas e Operações – Sales and Operations Planning (S&OP). O objetivo desse trabalho é a apresentação do novo modelo de S&OP da ArcelorMittal Brasil – Aços Planos, seus benefícios, e ferramentas utilizadas para suportar essa evolução: o SAP Integrated Business Planning for S&OP e a plataforma de colaboração SAP Jam, responsável por orquestrar todo fluxo de S&OP e as interações entre as diversas áreas envolvidas. O novo processo foi baseado nos conceitos existentes na literatura e também é objeto desse artigo. Além disso, no projeto de implementação do SAP IBP e SAP Jam foram utilizadas a Metodologia de Gerenciamento de Projetos baseada nas melhores práticas descritas pelo PMBOK (Project Management Body of Knowledge) do PMI (Project Management Institute) e a Metodologia SAP Activate para a implementação dos produtos. Como resultado da implantação desse projeto, foram obtidos vários benefícios, sendo alguns deles já atingidos e outros a serem capturados após o período de adaptação e estabilização dos processos e ferramentas.

Oct 30, 2017

By Luis Henrique Torres Dantas, Maycon Athayde, Rossano Augusto Pilon Nunes

The objective of this work is to evaluate the physical quality achieved in the iron ore pellets and the temperature profile in the pellet bed by applying an inversion in the flow during the cooling. The firing of pellets requires a minimum residence time in the sintering temperatures of the hematite grains [1]. The applied concept aims at raising this time to pellets located at the bottom of the bed which would provide an improvement in the physical quality of the product. The tests were carried out in a pot-grate type oven and the samples of fired pellets were divided into three aliquots according to the loading position of the pot termed top, middle and bottom, the pellets were sieved and subjected to physical tests and the compared to conventional indurating flow with the same ores and inputs. It was possible to show an increase of 7 to 8% in the compressive strength of the medium and bottom layers, maintaining the top layer results. The objectives of the research were achieved and the tests will be extended to assess the impacts on the mass and energy balance of the indurating machine and its components.

Oct 1, 2019

By Livia da Silva Mello

O objetivo deste trabalho é demonstrar que a utilização da Metodologia Six Sigma e ferramentas de controle estatístico e gestão, são eficazes para controle processo, redução custos e estabilização de processos em geral. O coque dentre os custos variáveis do Circuito Polimetálicos, representa o maior custo para a unidade de Juiz de Fora e a oportunidade em otimizar sua utilização, foi identificada a partir do levantamento de dados e benchmark realizado. Observou-se que a média do consumo específico de coque grosso + coque fino no Forno Waelz, em 2012 era em média 360 Kg/t de pó de aciaria (PAE) tratado estava muito superior a outras empresas que utilizam a mesma tecnologia para tratamento de resíduos. Definiu-se então como meta do projeto atingir 210Kg/t PAE até 2014. Passando por todas as etapas de um projeto Six Sigma: Definir, Medir, Analisar, Melhorar e Controlar, todas as ações realizadas garantiram uma melhor performance da variável: consumo específico de coque, uma média acumulada em 2013 de 212,3 Kg/t PAE e 181,5 Kg/t PAE em 2014 proporcionando um custo evitado de R$ 11,6MM para a unidade.

Sep 25, 2017

By Thomas Höfler, Michael Auinger, Bernhard Linder

Gas-fired pusher furnaces are commonly used to heat steel slabs before hot rolling. Temperatures well above 1000 °C combined with an oxidizing atmosphere containing H2O, CO2 and O2 result in rapid oxidation of most steel grades. The resulting oxide scale and the chemistry of the metal-scale-interface are major determining factors for the occurrence of hot rolling defects. To better understand these phenomena, lab-scale trials were performed with two different steel grades in an electric tube furnace in the temperature range 1000-1250 °C, using an atmosphere of about 20 % H2O, 7 % CO2 and 3 % O2. Humidification of the gas was achieved by evaporation, using a custom thermostat with standard laboratory glassware. The resulting samples were prepared metallographically, using cold mounting under vacuum with taper section angles, and analyzed using light microscopy and SEM/EDS. The scale structure of the Si alloyed steel was highly dependent on the oxidation temperature due to the formation of eutectic liquid phases of FeO, Fe2SiO4 and FeAl2O4. Below the eutectic temperature, the scale of the Si steel appeared to be made up of three distinct areas: The external scale consisting solely of Fe oxides, the internal scale containing Fe2SiO4 and FeAl2O4, and an internal oxidation zone with SiO2 and Al2O3 in a mostly plain Fe matrix. Comparisons of the experimental results with simulations of the internal oxidation showed good qualitative agreement.

Oct 1, 2019

By Leandro Rigo Ramos, Marcelo Lucas Pereira Machado, Lumena Gloria de Souza Nunes, Mariana Valinhos Barcelos

The aim of this work was to study the influence of temperature on the grain refining process from severe plastic deformations through the simulation of Accumulative Roll Bonding (ARB) by torsion tests. The assays were performed to simulate the ARB at three different temperatures of 550 ° C, 625 ° C and 700 ° C with 5 torsion cycles with equivalent strain of 0.8 per cycle at a rate of 0.1−1 , totalizing an accumulated deformation of 4.0. Grain refining was obtained with an average size of 2μm, 5μm and 6μm for the temperatures of 550 ° C, 625 ° C and 700 ° C respectively. There was a rise in Vickers hardness by 68%, from 119HV in the annealed sample to 175HV in the deformed sample at 550 ° C. In the deformations at 625 ° C and 700 ° C the value of 130HV E and 150HV respectively was obtained. Based on the obtained results, it can be stated that the severe plastic deformations in microliged steel, carried out at temperatures lower than the end of the austenite-ferrite transformation, produce refined grains of the order of 2μm and, consequently, increase the mechanical strength of the material.

Oct 1, 2019

By Antonio Esposito

Saving energy and reducing resource’s consumption by minimizing emissions are today great challenges in the coking industry worldwide. In order to achieve satisfying results, equipment as well as technology should be continuously improved and designed to minimize the energy requirements and to maximize the recovery of materials and energy. The sensible heat in coke pushed out of oven chamber takes up 35 ÷ 40 % of energy consumption of coke oven. Usually the coke thermal energy is lost during traditional coke wet quenching, necessary to reduce the coke temperature for the storage and the following use in steelmaking processes. BPSL CDQ project is a sample how Paul Wurth’s technology allows to reach the energy saving goal and offers an alternative to traditional quenching. With the adoption of Coke Dry Quenching process, a considerable amount of this sensible heat in the coke can be recovered by producing steam; its production depends on various parameters, some of them battery related (Volatile Matters in red hot coke) and others CDQ system related (coke burning losses, superheated steam characteristics (i.e. P,T)), greatly depending also on boiler efficiency (heat exchange efficiency, insulation of the boiler itself, air leakage, etc.). The adoption of CDQ process reduces also the water consumptions in comparison with traditional quenching.

Aug 16, 2017

By Emerson Sena Balbino, Emylle Alves Leitão, Gabriel Arthur Guieiro, Lucas van Melis

The deployment of autonomous haulage system causes several impacts in mining production chain, being necessary an appropriate change management policy, crucial to observe and gather all the benefits brought by the technology. The change management is also necessary to guarantee the adaptability of the organization in the long term. This paper briefly presents the technology deployed in the autonomous trucks at Vale's iron ore Brucutu mine, the changes that the operation team faces in the adoption of autonomous technology and the required training path to develop new procedures to deal with the sensitivity of the autonomous haulage system, besides the new operational dynamics from a process point of view, with safer, more consistent and more productive operations.

Oct 3, 2019

By Helênio Resende Silva Júnior

Arcelor Mittal Asturias coking plant at Gijon works, Spain, is undergoing a complete modernization of the whole coke making complex. In this context, Gijon has to be considered a brownfield project, where Paul Wurth has been awarded with the engineering, supply of key equipment as well as erection and commissioning supervision services for the rebuild of two coke oven batteries the modernization of the adjacent by-product and relevant waste water treatment plants. Main objective of this paper is to present the technological improvements introduced by Paul Wurth in the rebuild of a modern plant focusing on fulfilling all the recent environmental regulations.

Oct 30, 2017

By Vagner Machado Costa

O presente trabalho tem por objetivo analisar parafusos Classe 8.8 produzidos por 4 fabricantes nacionais. Para tanto, realizou-se caracterização mecânico-metalúrgica, baseando se nas normas ABNT NBR ISO 724: 2004 [3] e DIN EN ISO 898-1: 1999 [2]. O estudo de caracterização mecânica consistiu na realização de perfis de microdureza, ensaio de tração, MEV da superfície fraturada e medição dos perfis dos parafusos. A caracterização metalúrgica seguiu através de análise química e caracterização metalográfica (macrografias e micrografias). Está caracterização é de fundamental importância para verificar as variabilidades devido aos diferentes fabricantes as quais este componente está sujeito e compreender como elas podem vir a influenciar no desempenho deste produto.

Aug 16, 2017

By Luiz Cláudio von Sperling Cotta

A produção de pelotas de minério de ferro de alta resistência mecânica, que suportem o transporte e operação nos reatores de redução, necessita da correta adequação dos parâmetros de processo dos fornos de grelha móvel. A região de queima é a etapa decisiva neste equipamento para garantir a qualidade da pelota e também representa a maior parte da energia inserida no processo. No presente trabalho foi realizada a otimização do processo de queima, suportado pela metodologia Lean Six Sigma, avaliando a composição química da pelota, os ajustes de adição de combustível sólido na pelota e temperatura do perfil térmico de queima. Dessa forma, foram realizados ensaios em escala piloto para diferentes perfis de temperatura da etapa de queima. Não obstante, foram avaliadas as propriedades químicas, físicas, metalúrgicas e ainda foi realizada a avaliação microestrutural das pelotas. A validação dos estudos em escala laboratorial foi realizada através de testes industriais a fim de assegurar a qualidade do produto, a produtividade do forno e redução de custos de produção.

Aug 1, 2018

By Breno T. Maia, Débora C. O. Silveira, Mariana A. Ribeiro, Daniel A. G. de Carvalho, Roberto P. Tavares, Raissa S. Salgado

Mixing time is an important parameter when considering chemical and thermal homogenization in steelmaking reactors. It can also be relevant in the kinetics of chemical reactions. Different methods have been used to estimate mixing times in physical models of steelmaking reactors. In the present work a new method to estimate mixing times in physical models has been proposed. This method can be used when transparent fluids are used to simulate the liquid steel and the slag. Results of mixing times in a physical model of a BOF obtained with different techniques were compared. It was shown that the new method is more reliable and consistent than the common methods based on electrical conductivity measurements and colorimetric analysis.

Oct 1, 2019

By Antonio Augusto Gorni, Kenji Camey, José Herbert Dolabela da Silveira

Recently several studies have been developed on the use of microalloyed steels with low Mn content (below 1%) in the controlled rolling of heavy plates for the manufacture of pipes. However, this novel concept of alloy has peculiarities in its thermomechanical processing. Lower Mn contents should lead to the acceleration of NbCN precipitation kinetics during rolling, leading to a reduction in the soluble Nb content in austenite that delays its recrystallization by drag effect. This fact, plus the heavy and fast passes applied under virtually isothermal conditions in a heavy plate rolling mill with high power, increases the risk of partial recrystallization during the finishing stage of the controlled rolling, since strain hardening of austenite becomes significant and the interaction between precipitation and recrystallization is increasingly delayed. The objective of this study was to analyze the evolution of mean flow stress during the finishing stage of controlled rolling in these low Mn, high Nb microalloyed steels, in order to better understand the metallurgical mechanisms acting during this process and identify conditions that allow full compliance with the requirements of this product class.

Oct 1, 2019

By Luiz Afonso Andrade, Pablo Amâncio de Freitas, Ana Patrícia Andrade Jaccard, Eduardo Cezar Ribeiro, Ana Christina Pitard Lima, Rodrigo Ribeiro de Souza

A análise dos carvões em mistura é de suma importância para redução dos custos e controle de qualidade de uma coqueria, esse trabalho trata da influência da cominuição comum de carvões de diferentes ranks, assim como suas implicações no processo de amostragem e consequentes desvios nas análises. O processo de produção da mistura de carvões na Ternium Brasil possuía um desvio não rastreado entre matéria volátil resultante da amostragem automática da mistura de carvões e a matéria volátil esperada pelo resultado da média ponderada dos carvões individuais no recebimento, para tal foram estudadas todas as etapas do processo de produção da mistura de carvões desde a variação dos carvões em pilha, escoamento em silos e na etapa anterior e posterior a britagem. Os dados foram comparados e foi feito um plano de ação para redução do desvio.

Oct 1, 2019

By Maurilio Pereira Gomes

The aim of this work was to heat treat and characterize sintered valve seat inserts (VSI). The powder metallurgy route was the only way found to substitute cobalt and lead, used in the VSI original alloy, due to their high cost and toxicological effect, respectively. The studied VSI was obtained with AISI M2 high-speed steel powder mixed with iron powder and other additives such as manganese sulphide, graphite, zinc stearate, carbides and copper, which was added by metallic infiltration. All the VSI were air quenched and double tempered, for one hour each, at seven different equidistantly temperatures, ranging from 100 °C up to 700 °C. The physical and mechanical properties were evaluated by means of the VSI apparent density, apparent hardness and crush radial strength. The chemical composition was determined through gas analysis, for the light elements such as carbon and sulfur, and energy dispersive X-ray fluorescence spectrometry for other elements. Microstructural characterization was performed with the support of scanning electron microscopy and energy dispersive spectroscopy. Regarding the VSI final application, the best results were achieved with the inserts air quenched and double tempered at 600 °C.

Oct 30, 2017

By Osvaldo Guilherme Comineli

While the hot cracking of Cu-containing steels is a serious and widely known problem for the industry, the literature reports that copper only slightly impairs the hot-ductility measured in laboratory. A distinction is drawn between hot ductility and hot shortness and the respective cracking operating mechanism involved at the respective range of temperature. The representability of the laboratory assessment of hot cracking of Cu-containing steels by hot tensile tests compared with actual results in industrial practice is discussed. The effectiveness of the variable affecting in each cracking mechanism and respective temperature range, focused in improving the hot cracking assessment of Cu-steels and the relative importance of oxidation will also be discussed. It is concluded that the hot tensile test in argon might be a good simulation if properly interpreted and that the role of oxidation is secondary in causing hot shortness. A schematic diagram for the hot tensile test is proposed.

Oct 30, 2017

By Henrique Silva Furtado

Light meter is an ArcelorMittal innovation that uses off-gas light intensity to predict bath carbon, which is akin to the visual cues that the operators employ to finish a blow. Light meter enables the prediction of end point that is independent of any operator’s judgment. The results have been in general consistent with the actual carbon content at BOF end point at Tubarão. Besides some outliers that occurred due to strange intensity curves, the system implemented in Tubarão BOF 3 reported a carbon prediction error statistic that is very similar to dissolved oxygen–carbon end point statistics. Preliminary trials using light meter without any filter improved carbon hit ratio significantly.

Jul 30, 2018

By Christoph Sedivy

Industrie 4.0 is slowly but surely arriving in the melt shops. Furnaces are being equipped with more and more sensors, digital models are increasing the degree of automation, and information is being shared between different aggregates within the plant. Because the electrode control system plays a key role in electric steelmaking, it naturally assumes an important position in the melt shop’s Industrie 4.0 strategy. In addition to reliable, state-of-the-art core regulation functionality, monitoring and reporting tools and the ability to communicate with other equipment are also required. Therefore, the latest generation of our electrode control system, the Melt Expert, was developed based on Industrie 4.0 design principles. Intelligent plant condition diagnostics, performance monitoring, and user-defined reporting are essential modules in this new system. With these functionalities, electrode control systems are developing into the information and control center of the furnace. A newly developed software app brings most relevant process information to mobile devices. This feature allows steelmakers to keep an eye on the performance of their equipment anytime and anywhere. This paper describes the new features of the electrode control system and shares our customers’ operational experience. Our focus is on the practical aspects of plant status monitoring, KPI reporting, and diagnostic functionality as well as the improvements achieved.

Oct 30, 2017

By Michael Breuer, Christian Mengel, Luis Acainas Caballero, Olaf Jepsen

Stability of the hot strip mill rolling process remains a main topic when it comes to processing thin and hard materials. Strip steering especially at the end of rolling and tail out rips are a main source of unscheduled down times in a hot strip mill. Main focus of this paper is the new X-Roll® Guide system to improve mill stability and quality. An overview of SMS group developments in the recent years regarding equipment and control strategies is given. The new side guiding system in the entry area of the finishing mill is introduced and explained with operational examples. The system provides reproducible conditions for the threading process and during rolling. Steering control has a direct benefit on the availability of the mill. New developments of the roll alignment control strategies based on roll force and mill stand entry guide force measurement will be presented. Additionally a camera based measuring system is introduced that generates a direct process feedback of the strip position. It provides together with the roll alignment control the necessary control parameters for adjusting the roll gap and guiding the strip correct centered through the mill. As a summary the SMS group system is explained combining all features.

Oct 1, 2019