Search Documents

By Shilai Yuan, Huimin Lu, Zhijiang Gao, Panpan Wang

"Solvent refining of silicon through using Si-Al melts is a valid method to remove the impurities from metallurgical grade silicon (MG-Si) melt. The thermodynamic behavior of impurities Fe, Al, Ca, Ti, Cu, C, B and P in MG-Si during the solidification of MG-Si was studied based on the available thermodynamic parameters and experimental data. The morphology of inclusions was investigated by Scanning Electron Microscope (SEM). The chemical composition of inclusions in MG-Si and Al-Si melt was analyzed by EPMA. It is found that the amount of white inclusion reduces and most impurities are solved into the Al-Si melts. After solidification of Si–Al alloy using induction heating and acid leaching, impurities can be effectively removed. The solidification of silicon from the Si–Al melt is found to be more effective for purification than general silicon solidification.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. Multicrystalline silicon has now become the main material in the photovoltaic market because of its low production cost and because of the relative high conversion efficiency of solar cells made from this material, which has been studied for a long time [1-3].Electronic grade (EG) silicon (99.9999999% Si) is commonly used as the raw material to produce SOG-Si (99.9999% Si). Silicon produced from the chemical routes restricts the development of solar cells due to environment threaten, high energy consumption and low productivity. Purification of metallurgical grade silicon (MG-Si) is a low cost, environment friendly method. Although several metallurgical processes such as directional solidification, vacuum refining and electron beam melting [4], have been developed, the cost reduction and refining efficiencies for manufacturing silicon is still have to be further optimized.In the purification process, it is difficult to remove boron and phosphorus by the conventional metal refining method. The refining efficiency depends on the segregation behavior of different elements in solid silicon and the liquid phase. The segregation ratios of all investigated impurities were found to be much smaller than the segregation coefficients between solid and liquid Al-Si melts [5]. For instance, the segregation coefficient of B in Si is 0.8 at the silicon melting point (1687K), whereas it is around 0.2 when silicon is solidified from Si-Al melt at 1273K. For phosphorus the segregation coefficient is 0.06 when silicon is solidified from Si-Al melt at 973K°C, which is much less than 0.35 for recrystallization from liquid silicon. Since the segregation coefficient of boron in silicon is 0.8, it cannot be removed by directional solidification."

Jan 1, 2014

By Giuseppe Bonifazi

Minerographic and petrochemical research was carried out on crude ore samples from the complex polymetallic Zn-Cu-Pb sulfide ores of , Sotiel in Huelva province west of Seville, Spain. A computerized image analysis system was used to define the structural and textural characteristics of the ore to obtain information on the degree of liberation of the different minerals (i.e. pyrite, sphalerite, galena, chalcopyrite). Techniques of digital multispectral image processing of reflected light microscopy images were used. Particular structures were identified by means of mineral associations and numerically quantified to obtain useful information for designing beneficiation processes.

Jan 1, 1991

By F. Garcia-Carcedo

This research aimed to develop a clean technology for the production of ZnO from residues generated by the steel making industry. Scientific and technologic parameters were both investigated in order to define an industrial methodology allowing the integral recycling of EAF dusts. A reengineering of the Waelz process was perform,~d, aiming to produce a clean fraction of ZnO, fluorine free, as well as a slag enriched in metallic iron, which can be recycled in electric arc furnaces. The technical conditions used to produce the ultra pure fraction of ZnO are described. The magnetic separation of the EAF dust allowing the production of a phase high in iron and recyclable to the electric arc furnace is also discussed. Thermodynamic of the volatilization of all the elements contained in the EAF dust was performed in order to better control the thermal process in the rotary kiln. Tests were run using different reducing agents, weakly or highly reactive, aiming to determine their specific efficiency.

Jan 1, 2000

By Bradford C. Wesstrom

The extraction of metals from Copper Refinery Slimes may involve many different processes. This paper describes the use of pressure leaching for decopperizing of copper refinery slimes at the El Paso Refinery. Process equipment will be described, along with the process chemistry, unit operations and unit processes associated with the decopperizing process. Copper contained in the raw slimes ranges from 15-35%. After autoclaving less than 1 % copper remains.

Jan 1, 2000

By T. Johnson, B. Q. Li

"Electromagnetic stirring has found a wide application in metals processing for the benefit of obtaining refined solidification microstructures. This paper presents an experimental study on the melt flow and turbulent behavior in an electromagnetically stirred Woods metal pool. The experimental setup consists of metal bath unit equipped with temperature control to allow both cooling and heating, velocity probe positioning unit and data and signal acquisition and processing unit. The whole measuring system is under the control of an IBM personal computer. Velocity measurements are made using the incorporated magnet probes, which are calibrated using a turntable. The measured results showing the effect of the coil positions, coil arrangements and the applied currents on the melt flow are presented. Both mean flow and turbulence quantities are discussed.1. IntroductionElectromagnetic stirring is widely practiced in the metals industry for melt mixing and for casting microstructure refinement. Industrial examples are taken from induction furnaces where the electromagnetic forces are applied to generate desired melt mixing and also various types of electromagnetic stirrers used in various stages of steel and/or aluminum casting processes to produce fine grain solidification microstructure or to eliminate undesired defects such as TCG (twinned-columnar-grain) structure. For ultrahigh purity aluminum or high strength aluminum alloys containing zirconium or lithium, grain refinement can be difficult with the conventional technique, and electromagnetic stirring provides a particularly powerful means to obtain the refined solidification microstructure [1]. A fundamental understanding of the melt flow and the turbulence characteristics in these magnetically-driven flow systems is of significant engineering importance to both process design and product quality improvement.There exists extensive literature on the magnetically-driven melt flows in material processing systems. Nakanish. et al. [2] were perhaps among the early investigators to mathematically and physically model the magnetically-driven flow phenomena in molten metal systems. Subsequent theoretical and experimental work by Tarapore and Evans [3, 4], Szekely and Chang [5], Hunt and Moore [6] and Szekely and El-Kaddah [7] has contributed very significantly to our understanding of magnetically-driven flow in inductively stirred melts. They have developed mathematical models for the electromagnetic field and turbulent flow in induction furnace and validated the models by either laboratory experiments or direct measurements in the industrial-scale induction furnaces."

Jan 1, 1998

By Wenbin Liu

A novel route for rapid synthesis of ultrafine WC-Co cemented carbides with homogeneous binder phase distribution is reported. The composite powder is produced by in situ reduction-carbonization reactions by using WO2.9, Co3O4 and carbon black as raw powders. The reaction equilibrium and phase stability are studied by thermodynamic calculations. The WC-Co composite powder is condensed by spark plasma sintering (SPS) to obtain the cemented carbides bulk. The sintering temperature is lower than that in the conventional sintering methods by 1500C, while the sintering time is remarkably reduced by 3-5 times. The high performances of the hardness and the fracture toughness are obtained. The experimental results confirm that the present processing scheme of in situ reduction-carbonization reactions and subsequent SPS sintering is an efficient way to prepare WC-Co cemented carbides, and is apparently superior to the conventional long-period techniques of preparing composite powder and cemented carbides bulk.

Jan 1, 2008

By Takuya Shinagawa

After vitrification of the residues from a municipal solid waste incinerator, the vitrified products can be used as a construction material, and the dust can be used as raw materials for the non- ferrous industry. The NKK electric-resistance furnace is operated under a reducing atmosphere, and heavy metals such as zinc and lead in the ash vaporize to form dust. Also, dust from the NKK electric-resistance ash melting furnace is composed of water insoluble zinc and lead components and water soluble NaCl and KCI. This is why, The concentration of zinc and lead in the dust after washing is sufficiently high for the dust to be used as a raw material for the zinc and lead industry. NKK developed a heavy metal recovery process in which zinc and lead in the dust are reclaimed as a raw material for smelting by making the best use of the characteristics of the dust.

Jan 1, 2002

By Nourreddine Menad

Plastic materials have been associated with electric and electronic applications since the early days of the electrical industry. Plastics can amount to 30 percents of the scrap mass. Generally, they are treated with flame retardants such as halogenated ones and they can result in different toxic chemical compounds. These plastics can be used as combustibles in the recovery of copper and precious metals. However, during their combustion, halogenated flame retardants can produce dibenzo-p-dioxins and dibenzo-furans. The estimated thermodynamic data of several organic compounds resulting from combustion of electric and electronic scrap, have been used in conjunction with the program HSC to calculate the conditions for dioxin and furan formation. The results show that the formation of the dioxins is dependent on the quantities of carbon, hydrogen, chlorine and oxygen reacting in a given system, as well as on parameters such as temperature and pressure.

Jan 1, 1998

By Md. Maniruzzaman

The quenching performance of a liquid quenchant can be controlled by controlling the agitation in the quench tank. Without agitation, a vapor layer or bubbles form at the hot part surface and the natural convention of the quenchant limit the heat extraction rate at the quenched part surface. Resistance to the heat extraction rate can be reduced by breaking the vapor layer or by inducing a turbulent convection at the part surface through agitation (Le. forced circulation of the quenchant). To determine the effects of agitation on the quench performance of a mineral oil based quenchant, the CHTE quench probe system was used with AISI4140 steel probe tip. Quenching performance of the oil is evaluated by computing the effective heat transfer coefficients of the steel probe as a function of surface temperature using Lumped Parameter Analysis. In addition, computational fluid dynamics (CFO) simulation of the quench tank with an impeller type agitator has been done to understand and predict the fluid flow pattern in the tank. CFO simulation also provides insights for determination of optimal location of the impeller and the quench probe tip. Keywords: CHTE Quench Probe, agitation, CFD simulation, liquid quenchant, 4140 steel

Jan 1, 2003

By Victoria Vaccarezza, Corby Anderson

Due to the demand for rare earth elements for everyday technology and applications, there has been much research initiation into the extraction and recovery of rare earth elements. An otherwise unknown mineral, eudialyte is a zircon silicate consisting of rare earth oxides, specifically the heavy REO yttrium (III), with only trace amounts of thorium and uranium. The first part of this project aimed at finding an efficient way to liberate and upgrade eudialyte to concentrate the REO content. A combination of gravity and magnetic separation techniques were employed, resulting in limited success. The second part looked at the hydrometallurgical processing of eudialyte through various leaching experiments with sulfuric acid. In all, this project will discuss why certain processes were utilized over others, as well as the difficulties that arose during processing.

Mar 1, 2018

By T. T. Chen

Gold in the Twin Creeks ore is primarily associated with arsenian pyrite. During pressure oxidation, the sulphides are solubilized, but part of the dissolved iron reprecipitates as jarosite and as an iron sulphate-arsenate-phosphate phase. The pressure oxidation products are subjected to cyanide leaching. The cyanide leach residues consist of quartz, gypsum, bassanite, anhydrite, small amounts of jarosite, an iron-sulphate-arsenate-phosphate phase, as well as trace amounts of orthoclase, rutile, pyrite, hematite and monazite; all these particles are dispersed in a fine grained matrix of illite-muscovite. The autoclave leach residues contain a small amount of carbonaceous matter. Many gold grains are detected on the surfaces of the carbon particles, and these gold particles are not leached during cyanidation. The gold particles are typically 0.1-0.2/Lm in size and commonly are embedded in the carbon surface or are coated with a K-AI-Si-S-O phase on the surface of the carbon. The gold grains are consistently associated with elevated CI contents (50-300 ppm Cl). The poor gold cyanide leach recoveries, which initially occurred in the Twin Creek developmental circuit under certain operating conditions, are attributed to the presence of chloride in the feed. This results in the formation of soluble gold chlorocomplexes in the autolcave and the subsequent sequestering of the gold on the surfaces of the carbon particles.

Jan 1, 2000

By David J. Kinneberg, Barbara E. Mangion, Arnold M. Savolainen

Analytical laboratories require a qualitative or semi-qualitative method of determining major and minor constituents in "unknown" samples to select optimal analytical techniques. This is exceedingly important in precious metal assay laboratories where the precision and accuracy requirements are exacting (routinely within 0.02%, absolute basis). This paper describes the use of an x-ray fluorescence spectrometer with a specially designed software package to select optimal analytical procedures and specify relevant analytical parameters. A wavelength dispersive XRF spectrometer is capable of quick and accurate analyses of properly prepared samples without extensive standardization. When coupled with a specially designed software package, this preliminary assay system is applicable to a wide variety of sample types including gold and silver bullion, karat gold and karat PGM alloys, high silver and high copper metallic samples as well as particulate samples of ores and sweeps. The system relieves the assayer of tedious calculations for silver inquartation and proofing, minimizes human error and standardizes selections over time. Most importantly, the system allows for independent verification of final assay results.

Jan 1, 1999

By N. A. Warner

Fundamental studies on the reaction of limestone or dolomite at high temperature with S02 are extended to the realm of large scale primary copper smelting. Whereas flue gas desulfurisation in the electric power utility industry is concerned with S02 concentrations normally less than 0.5 percent, high temperature smelting gases can have S02 levels approaching 100 percent. The reaction involved is very exothermic so proposals are made in this paper for returning the heat generated in sulfur fixation directly back to the copper smelting process. This integration leads to metal production with lower energy requirements than current technology. The anhydrite reaction product can either be disposed of locally with minimum adverse environmental impact or upgraded to a value-added product. It is assumed, of course, that no viable market exists to support sulfuric acid production.

Jan 1, 1996

By Dao-Wu Yang, Ju-Lan Zeng, Li-Xian Sun, Yan Yao

"The hydration heat of the pure cement, the fly ash single-dopped cement, as well as the fly ash and fluorgypsum co-dopped cement were investigated by means of micro-calorimety with an eight-channel micro-calorimeter (TAM Air). The results showed that the hydration heat and the hydration rate could be reduced significantly by fly ash and fluorgypsum. However, the reduction was not proportional to the loading of dopant. The exothermic peak of the fly ash and fluorgypsum co-doped cement was appeared earlier than the fly ash single-doped cement. As the temperature decreased, the hydration heat and the hydration rate of the doped cement were reduced, and the exothermic peak appeared later. The effects of fly ash and fluorgypsum on the compressive strength of cement were also investigated. The results revealed that the early compressive strength of concrete made up of the co-doped cement was largely higher than that of the fly ash single-doped cement. Based on the experiment results obtained in this paper, we could conclude that fluorgypsum is a suitable additive for fly ash-doped cement.IntroductionFly ash and fluorgypsum are industrial waste. In 2008, nearly 400 million tons of fly ash has been produced by coal-burning power plants in China. And it is estimated that this number would exceed 500 million at the year of 2015. Besides, every year the fluoride salt factories in China discharge more than 100 million tons of fluorgypsum. Tremendous of fly ash and fluorgypsum occupy considerable land and contaminate air and water sources [1]. As a result, comprehensive utilization of this two industrial waste has draw great attention from all over the world.Cement is the most-used construction material on earth. But the production of cement consumes huge energy and destroys the environment. This problem might can be partly solved by applying fly ash and fluorgypsum as additive for cement [2-4]. During the last decade, some papers that focused on applying fly ash and fluorgypsum as additive for cement have been published [5, 6]. However, to the best of our knowledge, none of these papers investigated the hydration heat of the fly ash and fluorgypsum co-doped cement.The hydration of cement is an exothermic reaction, which can result in serious problem for mass concrete: The interior of the concrete could reach very high temperature as the hydration proceeded [7-9]. As a result, the great temperature difference between the interior and the outer of the concrete would exist and cause serious thermal stresses. Thus, the concrete would be destroyed by the cracks which in tum are resulted from the thermal stresses [10, 11]. The heat released by the cement hydration and the hydration rate is commonly regulated by adding mixed materials or transferring additive such as fly ash and fluorgypsum [12-14]."

Jan 1, 2011

By M. Friák, L. G. Wang, M. Šob, V. Vitek

"The paper gives an account of applications of quantum-mechanical (first-principles) electronic structure calculations to the problem of theoretical tensile strength in metals and intermetallics. First, we briefly describe the way of simulating the tensile test and the electronic structure calculational method. Our approach is then illustrated on calculations of theoretical tensile strength in W, NiAl and transition metal disilicides MoSi2 and WSi2 with C11b structure. In Wand NiAl, we consider uniaxial tension along [001] and [111] directions. Although tungsten is elastically nearly isotropic (C44 = C”), theoretical tensile strength exhibits a marked anisotropy (oth/001 = 29 GPa, o'th/111 = 40 GPa). Calculated results compare favorably with experimental value of 24.7±3.6 GPa obtained for tungsten whiskers grown along the [110] direction. Similarly, in NiAl, the 'hard' orientation [001] differs very significantly from the [ill] orientation (oth/001 = 46 GPa, oth/111 = 25 GPa). This anisotropy is explained in terms of higher-symmetry structures present or absent on the calculated deformation paths. In disilicides, the theoretical strength is calculated for [001] loading (oth/001 = 37 GPa and 38 GPa for MoSi2 and WSi2 , respectively). The role of relaxation of internal structure parameter is discussed and changes in bonding conditions during the tensile test are analyzed.IntroductionIn most engineering applications, the strength of materials is limited by the presence of internal defects. If there were no defects, then, for example, the tensile strength could be several orders of magnitude higher and its value would be comparable with that of shear modulus. Therefore, the strength of ideal (defect-free) crystal represents an upper limit of attainable stresses, which is called the ideal strength. While it may not be possible to achieve the ideal strength in practice, it is not possible to exceed it. However, the ideal strength is already approached in situations which are technologically relevant. These include the low-temperature deformation of inherently strong materials, such as diamond, Si, Ge and some of the transition-metal carbonitrides, deformation of whiskers, nanoindentation of materials with low defect densities, hardened thin films and coatings etc. The ideal strength sets the limits of elastic stability of a solid. Its knowledge is useful for estimation of the ideal work of fracture stresses needed for homogeneous nucleation of dislocations and for modelling of crack propagation."

Jan 1, 2001

By Yichi Lu, Haydn N. G. Wadley, Douglas T. Queheillalt

"Using a 3-D ray tracing methodology combined with laser ultrasonically measured elastic constant data near the melting point, ultrasonic propagation in cylindrical single crystal bodies containing either a convex or a concave solid-liquid interface have been simulated and used to design new sensing concepts. Ray paths, wavefronts and time-of-flight (TOF) of rays that travel from a source to an arbitrarily positioned receiver have been calculated. Experimentally measured TOF data have been collected using laser generated/detected ultrasound on model systems with independently known interface shapes. Both numerically simulated data and experimental results have shown that the solidification (interfacial) region can be identified from ultrasonic transmission TOF data. Since convex and concave solid-liquid interfaces result in distinctively different TOF data. When TOF data collected in the diametral plane are used in a nonlinear least squares algorithm, the interface curvature has been successfully reconstructed and ultrasonic velocities of both the solid and liquid obtained. The reconstruction errors were found to be less than 5%.IntroductionMany of today's single crystal semiconductors are grown by variants of a vertical Bridgman technique in which a cylindrical ampoule of a molten semiconductor is translated through a thermal gradient, resulting in directional solidification and the growth of a single crystal, Fig. 1.1 It has long been recognized that during crystal growth the velocity and the shape of the solid-liquid interface, together with the local temperature gradient, control the mechanism of solidification (i.e. planar, cellular or dendritic), the likelihood of secondary grain nucleation/ twin formation (i.e. the loss of single crystallinity), solute (dopant) segregation, dislocation generation, etc. They thus determine the crystals' resulting quality.2-4 The solidification rate and the solid-liquid interface shape are also sensitive functions of the internal temperature gradient (both axial and radial) during solidification.5•6 This in turn is governed by the heat flux distribution incident upon the ampoule, the latent heat release at the interface, and heat transport (by a combination of conduction, buoyancy and surface tension driven convection, and radiation) within the ampoule. The solid-liquid interface's instantaneous position, velocity and shape during crystal growth are therefore difficult to predict and uncontrolled during growth, especially for those semiconductor materials with low thermal conductivity (e.g. CdTe).4-6 The development of technologies to non-invasively sense the interface position and shape throughout the vertical Bridgman crystal growth process has therefore become a key step toward developing a better understanding of the growth process, for enabling sensor-based process control, and thus ultimately for improving the yield and quality of difficult to grow semiconductor materials like CdTe."

Jan 1, 1997

By Joon H. Jang

At a selected pH, hydrothermal oxidation of chalcopyrite was carried out under controlled F+,, at elevated pressures and temperatures (172-200°C) by balancing the rate of oxygen injection against the rate of consumption. Chalcopyrite was converted to covellite (CuS) and digenite (CU1.8S) with rejection of iron and sulfur to the solution. Covellite forms in the first stage, followed by nucleation and growth of digenite in the second stage. The effects of rapid and slow injection of stoichiometric quantities of oxygen are compared. Both the covellite and digenite form a porous layer occupying the same volume as the original chalcopyrite grain. An electrochemical kinetic model is presented to correlate the observed results.

Jan 1, 1993

By J. D. Law

The presence of long-lived radionuclides presents a challenge to the management of radioactive wastes. Separation of the radionuclides from the waste solutions has the potential of significantly decreasing the costs associated with the immobilization and disposal of the waste by minimizing waste volumes. Several solvent extraction processes have been developed at the Idaho National Engineering and Environmental Laboratory for the separation of transuranic elements (TRUs), 90 Sr, and/or 137 Cs from acidic radioactive waste solutions. The TRUEX and POR processes for the separation of TRUs, the SREX process for the separation of 90Sr, the cobalt dicarbollide process for the separation of 137Cs and and a universal solvent extraction process for the simultaneous separation of TRUs, 90Sr, and 137Cs have all been developed in centrifugal contactors using actual liquid radioactive waste solutions and simulated dissolved calcine waste solution. In addition, the behavior of metals with each of the solvent extraction processes was evaluated. This article summarizes the most recent results of the each of the flowsheet demonstrations and provides Information on the centrifugal contactor equipment used for the testing.

Jan 1, 1999

Arsenic occurs naturally in rocks and soils, water, air, plants and animals. It can be further released into the environment through natural activities such as volcanic action, erosion of rocks and through human actions. Higher levels of arsenic tend to be found more in ground water sources than in surface water sources of drinking water. Compared to the rest of USA, western states have more systems with arsenic levels greater than 10 parts per billion (ppb). The US Environmental Protection Agency (EPA) has historically regulated arsenic in drinking water at 50 ppb, but the agency has lowered the maximum contaminant level (MCL) for arsenic to 10 ppb-to be in compliance by January 2006.This paper reviews briefly a) aqueous arsenic chemistry and removal mechanisms and b) the available treatment processes to attain the drinking water standard of 10 ppb by 2006. The combining of an appropriate removal method with an existing system depends on several factors such as nature of arsenic, the water source, existing plant equipment and processes site conditions etc. The paper also includes one or two case studies from the State of Arizona. Key words: Arsenic, Drinking water, Treatment Technologies

Jan 1, 2005

By J. W. Dini

Introduction The mission of the Materials Fabrication Division (MFD) is to provide fabrication services and technology in support of all programs at Lawrence Livermore National Laboratory (LLNL). MFD involvement is called for when fabrication activity requires levels of expertise, technology, equipment, process development, hazardous processes, security, or scheduling that is typically not commercially available. Customers are encouraged to utilize private industry for fabrication activity requiring routine processing or for production applications. MFD is .a large diversified service organization including approximately 400 full time employees. The group provides a wide variety of processes including all common machining and fabrications operations, laser and water jet cutting, electrical discharge machining, lapping, electron beam and laser welding, vacuum brazing, heat treating, forming, electroplating and metal finishing, optical polishing and grinding, vacuum coating, vacuum engineering and a variety of plastics operations. These operations occupy more than 1,250,000 square feet of floor space. For more detail on the many fabrication related services available from MFD, see Reference 1.

Jan 1, 1992