Search Documents

By M. M. Kim

Zn-27% Al was pressure infiltrated into a column of 20 micron diameter abrasive grade SiC particles to give billets with particle loading of 50 voli.une %. Some billets were heated to a temperature where they became semi-solid and diluted with liquid Zn-27% Al alloy to give billets with particle loadings of 12 and 16 volume %. Some of these billets were then extruded into wire with an area reduction of approximately 98%. Tensile properties of the as-cast billets were always inferior to those of the matrix alloys; however, the extruded composite samples showed at 37% improvement in ultimate tensile strength compared to their extruded conventional counterparts. The fracture surfaces of these samples are described.

Jan 1, 1990

By Kuniaki Murase, Tetsuji Hirato, Yasuhiro Awakura

"Electrodeposition of CdTe was studied using aqueous ammonia-alkaline electrolytic baths in which Cd11-and Te1V-ions are dissolving as Cd11(NH3)/+ and Te1vol-ions, respectively. Ca-thodic polarization curves of the baths suggest the presence of strong interaction between the Cd11-and Te1V-ions; electrodeposition of tellurium is inhibited by the presence of Cd(NH3)/+ ions. The interaction makes it possible to electrodeposit CdTe films with stoichiometric composition. Polycrystalline CdTe thin film of about 1 µm thickness was electrodeposited at 343 K from ammonia-alkaline solutions (pH= 10.7) containing TeO32-(<20 mmol dm-3) and Cd(NH3)/+ ( < 60 mmol dm-3) ions. Increasing Cd(NH3)/42+/TeO32- mole ratio or decreasing total concentration of ammonia/ammonium-ion gave flat and smooth crystalline CdTe deposits at constant cathode potential-0.70 to -0.30 V vs SHE at 343 K.IntroductionCadmium telluride (CdTe) is well-known as a compound semiconductor whose band gap, i.e. 1.44 eV, is suitable for solar energy conversion with a photovoltaic cell. Various methods, such as CVD (chemical vapor deposition) and electrodeposition, of preparing CdTe thin films for solar cells have been investigated.Acidic sulfate solutions with a pH of 1-2 are usually employed for CdTe processing by electrodeposition.1-3) The electrodeposition of compound semiconductors is usually achieved (i) at a higher cathode potential than the redox potential of less-noble species, can in this case, and (ii) under the condition of diffusion-limiting current of a more noble species, Te1Y.4) There-fore, a suitable CdII/TeIV concentration ratio in the acidic electrolytic baths, resulting in the deposition of stoichiometric CdTe, is determined by the diffusion-limiting current density of TeIV- reduction, i.e. the concentration of HTeIVO2+ · Since the solubility ofTe1v species HTeIVO2+ in the acidic solutions is quite low, the rate at which CdTe is deposited from the acidic solutions is extremely slow."

Jan 1, 1998

By D. Gu, R. G. Anthony, C. V. Philip, M. E. Huckman

"In this paper, we review the equations needed to construct an ion exchange column model. These models contain three major components: 1) a differential material balance around the column, 2) a differential material balance around an ion exchange particle, and 3) a constitutive equation for diffusive flux. We then examine the ability of a fairly simple mathematical model to predict ion exchange column experimental data. This model contains the traditional absorption theory equations and is used to predict the behavior of a column filled with a hydrous crystalline silico-titanate and which is removing trace amounts of Cs+ from a high pH, complex electrolyte solution. Finally, we propose replacing Fick's law with the Nemst-Planck equation as the constitutive equation for diffusive flux. We use a NemstPlanck type model to predict batch experimental data, then evaluate it by comparing it's ability to predict experimental data to that of a more traditional Fick's law type model. The data from this comparison suggests that the Nemst-Planck type model yields better results.IntroductionMillions of gallons of strongly basic, radioactive waste are currently stored in underground storage tanks at Hanford and Savannah River and several locations within the United States. Due to the limited life expectancy of the tanks, there is a pressing need to remediate these wastes. This need has prompted the recent development of new ion-exchange materials for removing radioactive elements from aqueous solutions. A novel material called TAM-5 has been developed jointly by Texas A&M University and Sandia National Laboratories. TAM- 5, a crystalline silico-titanate, is highly selective for Cs + in the complex electrolytic solutions typical of these wastes. It is stable in very basic solutions and in radioactive environments [1, 2 ,3]. In laboratory testing to determine the selectivity of various materials, TAM-5 was superior to other candidate ion exchangers [4, 5]. The selectivities were determined by measuring a distribution coefficient, Kd, which is defined as the concentration, gig or mmols/g of Cs in the solid phase divided by the concentration, mg/L or mmols/mL, of Cs in the liquid phase. The units of Kd are ml/g or L/kg. Table 1 shows Kd values for TAM-5 compared to 9 other candidate materials in a typical waste solution [6]."

Jan 1, 1996

By Bernd-Arno Behrens, Klaus-Georg Kosch

"In times of increasing energy costs automotive lightweight construction is gaining in importance. This paper deals with the production of hybrid steel-aluminum compounds by forging. The compound forging process is a promising method to successfully manufacture functional parts by applying resource-saving process steps. Nevertheless, challenges resulting from different material properties must be solved.The heating of hybrid material work pieces made of steel and aluminum is a great challenge. Steel is forged at a temperature of at least TSt =900 °C, while aluminum should not exceed a temperature of TA1= 500 °C. For achieving the required temperature gradient extensive experimental investigations have been carried out. Intermetallic phases form during the manufacturing process and can influence the bonding and the global part quality. In addition, methods for the characterization of the joining zone between the materials steel and aluminum are analyzed and the factors influencing the formation of intermetallic phases are determined experimentally.IntroductionIn times of increasing energy costs and stricter conditions relating to environmental protection, automotive lightweight construction is gaining in importance. The production of hybrid compounds by forging is a promising method to manufacture functional parts by applying resource-saving process steps. In compound forging a hybrid raw part consisting of a solid core, which is enclosed by a hollow casing, is joint in the forming process. This results in a graded material structure in the part in which the mechanical properties can be specifically adapted to the requirements. Compound forging is the form joining and/or firmly bonded joining of at least two different materials while plastic shape forming occurs (Figure 1)."

Jan 1, 2012

By F. T. Principe

In order for solvent extraction technology to be acceptable as an alternative to existing jarosite precipitation circuits, iron must be cleanly separated and concentrated into a feed stream suitable for downstream iron by-product recovery which meets market specifications and economics. Ten years ago, significant progress was made in a joint McCill University/CANMET project that involved iron extraction with mono(2-ethylhexyl) phosphoric acid and stripping with HCI. Our iron solvent extraction research was reactivated recently by looking into this and other members of the organophosphorus extractant family. Our research focuses on the mechanisms and control of anion (SO42/CI) transport across the various phases (Rafinate/Organic/Strip), iron build-up in the strip liquor, and extractant stability/selectivity. In this paper, these issues along with some other performance parameters are discussed using data derived from an extensive search of the two commercially available and best known members of the organophosphorus family, di-2-ethylhexyl (D2EHPA) and mono-2-ethylhexyl (M2EHPA) phosphoric acid. Further in this discussion, the challenges lying ahead in the development of sx systems that overcome the deficiencies of D2EHPA and M2EHPA are outlined. In particular, the necessity of considering secondary separation technologies that can further concentrate iron values in the chloride strip liquor to levels economically attractive for the production of saleable iron oxide by pyrohydrolysis is addressed.

Jan 1, 1998

By Dinesh P. Amalnerkar, Nagegownivari Munirathnam, Tirthalli Prakash, Katia Vutova, Vania Vassileva, Veliko Donchev

"A time-dependent model for electron beam melting and refining (EBMR) of different metals and alloys is developed. The model is 3D axi-symmetrical and an adapted numerical scheme of Pismen-Rekftord type is applied. The developed computer program computes the thermal fields in the metal ingots during EBMR process as well as the dynamics of the thermal streams and the geometry of the molten metal pools. Calculated results for different regimes of EBMR of titanium are obtained and discussed in the paper. Experiments are performed and impurities' concentration data are presented. Simulation results are compared with experimental data and are used for optimization of the EBMR process in the case of Ti.IntroductionElectron beam melting and refining (EBMR) has an important role in the special electrometallurgy[ 1-6] and it is approved for obtaining of pure titanium [7]. EBMR of metals and alloys is being recognized as a competitive and even the single method for obtaining new materials for all areas of human activity.The principal scheme of the EBMR drip process is shown in Fig.1. A thin layer of molten metal is formed on the front part of the feeding rod during the e-beam processing and generated droplets fall into the molten pool in the crucible where the ingot is formed. The refining is mainly realized at the boundary liquid metal - vacuum. There are three zones in EBMR (Fig.1) - on the front part of the feeding rod (zone I in Fig.1 ), on the surface of the generated droplets (zone II in Fig.1) and the surface of the molten pool in the water-cooled copper crucible (zone III in Fig.1)."

Jan 1, 2013

By B. S. -J. Kang, M. A. Alvin, J. M. Tannenbaum

"A load-based micro-indentation technique has been developed for damage assessment and non-destructive spallation detection of TBCs at room temperature. This micro-indentation technology has been further extended to the development of a high temperature (HT) test methodology. Elastic modulus calibration tests performed on Hl 3 Tool Steel to 500°C and Haynes 230 at 1000°C displayed excellent agreement with reported values. Moreover, indentation creep tests of Haynes 230 at 1200°C were found to be in agreement with known creep exponents as well. Finally, a HT thermal flux indentation apparatus was assembled for conducting TBC turbine component testing under high temperature moisture-containing environments (= 50% steam with controlled gas content temperatures up to 1250°C). Description and design considerations of this test apparatus are discussed. Preliminary tests of ReneN5/MCrAlY/APS TBC coupons in steam/air environments with in-situ HT micro-indentation testing are conducted. Furthermore, the coupon is removed and examined for damage assessment at periodical intervals.IntroductionLoad and depth relationships acquired throughout the indentation process provide insight to material mechanical properties such as elastic modulus and hardness. Unloading segment analysis of these load displacement curves are utilized in the acquisition of a material's elastic properties. Yet, indentation tests are complex processes involving contact mechanics, material nonlinearity and even fracture mechanics. Thus exact analytical solutions for these processes are difficult to obtain. As a result, much of the current knowledge regarding the indentation process has been acquired through experimental methods and finite element simulations. Initial efforts by Tabor resulted in the application of spherical indentation to obtain post-yielding stress/strain relationships [1]. Soon thereafter, analytical load-depth relations for elastic indentation were developed [2], yet it was Lure who further derived the explicit relationships for both spherical and conical indenters [3]. Improving upon this, these interactions were later extended to indenters with various geometries by various researchers [ 4]. Additionally, by establishing the linearity of the initial unloading slope within the load-depth curve, a relationship between elastic indentation depth, maximum load, unloading slope and indenter geometry was established [5]. From this a theoretical method by which elastic modulus could be determined was established."

Jan 1, 2011

By Shadia J. Ikhmayies

Polycrystalline CdTe thin films were prepared by vacuum evaporation on glass substrates. The I-V plots which were linear were used to find the resistivity. A value of 2.10×106 .cm was obtained. The transmittance was measured in the wavelength range 400-1100 nm. The bandgap energy was found to be 1.48 eV. X-ray diffraction pattern shows that the material deposits in the zinc blend structure with one strong reflection from the C(111) plane. The scanning electron microscope image shows a uniform surface with a small density of large (mµ1£) grains scattered on the surface.

Jan 1, 2009

By George S. Dulikravich

An advanced semi-stochastic algorithm for constrained multi-objective optimization has been adapted and combined with experimental testing and verification to determine optimum concentrations of aJ10ying elements in heat-resistant and corrosion-resistant H-Series austenitic stainless steel alloys. The objective was to simultaneously maximize a number of alloy&apos;s mechanical properties. This research will result in a rigorous tool for the design of high-strength H-Series steels and other types of alloys unattainable by any means existing at the present time. Such a material-by-design tool will also be able to reduce or minimize the need for the addition of expensive elements such as Cr, Ni, Co, Nb, Ti, V, etc. and still obtain the optimum properties of an aJ1oy.

Jan 1, 2003

By Daguang Lu

The section of sintering and BF (blast furnace) is very important in iron-making process. In practice, the scheduling is so extensive that three faults unfavorable to continuous product will be easier to happen. This paper introduces the integration Petri Net and GA (genetic algorithm) as suitable tools for simulation and optimization of scheduling to section of sintering- BF under a certain hot iron or-der. The situation of the iron plant Chongqing Iron and Steel Company is researched in approach above mentioned. By analysis, the conclusion is drawn that scheduling with optimized values can maintain continuity of key operations , can satisfy order of hot iron in maximal degree and can keep the best stability of key storages.

Jan 1, 2009

By Shigehisa Endoh, Hitoshi Ohya, Atsushi Inaba, Shigeki Koyanaka

"Recycling should be promoted to keep the global environment. However, it is difficult to detennine the quantitative impact. A life cycle assessment is one of the most reliable methods to estimate the global environment impact.Exergy is useful like entropy when considering the sustainable development. All of our activities have been obtained exergy resources and/or energy itself and throw away waste and/or waste heat. We are trying to use exergy to estimate the quantity of energy and matter for resource accounting. For recycling plastic, plastic has two aspects; material and energy source.The environmental assessment of plastic recycling suggests that the exergy reduction of the entire system is estimated by the yield of matter and the process efficiency. The material recycling is better than the thennal recycling when the process efficiency is high. However, the thennal recycling is much better for the low efficiency. The transition point is able to be decided by the efficiency of the manufacturing and the electric power generation.IntroductionRecently, many of the global environmental problems have become conspicuous like global wanning, ozone layer depletion and acid rain. Some of the methods like life cycle assessment for solving these problems have been presented. Anxiety concerning the proble1ns of energy and resources has led to a rapid increase in the interest in describing and understanding the conversion processes of energy and other resources in today's society. All human activity is supported by obtaining power and products of high exergy from the environment and throwing away the waste material and the waste heat of low exergy back the environment. However, the total exergy in the whole system becomes absolutely smaller than before.The rate of obtaining high exergy products and energy itself by human activity and the speed, by which waste and waste heat having low exergy are thrown away are too fast to attribute to environmental problems [1-3].A material's use by recycling was often common in a circulating society mainly. A significant amount of energy is consumed during circulation. An environmental impact assessment method for the process or the system has not been devised when both of them are taken into consideration. Even if the life cycle assessment evaluation, which has been correctly used up to now, is applied, it is not sufficient for an overall evaluation concerning matter and energy.The real sustainable development is that the exergy reduction value by all human activities on the earth is kept within the range of the exergy reduction in order to consider the earth as closed stationary system. It is important to evaluate the process or the system by using the exergy, and design them so that the exergy loss may decrease as much as possible. We have to consider what process improvement is the most effective."

Jan 1, 2000

By Huayi Yin, Wang. Dihua, Wei Xiao, Xuhui Mao, Diyong Tang

"The world production of crude steel reached 1.55 billion tons in 2012,which generated ~2.5 billion tons of CO2. Electrochemical metallurgy especially through high temperature molten salt electrolysis with renewable electricity stands for a great opportunity for producing “green” metals. In recent years, electrolytic production of iron without emission of CO2 in different molten salt systems has been reported. A cost-affordable inert anode is the key to produce acceptable eco-friendly iron by the novel molten salt electrolysis processes. Based on the authors’ research, this paper will discuss iron production by molten salt electrolysis using a nickel alloy inert anode. On the other hand, the paper also covers a novel molten salt CO2 capture and electrochemical transformation (MSCC-ET) process, in which CO2 is effectively converted to value-added carbon and oxygen in a molten bath using a cost-affordable nonconsumable SnO2 anode.1. IntroductionEnergy and materials are cornerstones to support the development of human society. The traditional primary metal production, especially iron and steel, and electricity production are mainly based on the reactions between carbon (coal) and oxygen (represented by equations (1) and (2) respectively), which produce huge amount of CO2.MxOy + 0.5y C = x M + 0.5y CO2 (g) + Q1 ( 1 )C + O2 (g) = CO2 (g) + Q2 ( 2 )In 2012, the world production of crude steel reached 1.55 billion tons, of which 46.3 %, ~0.7165 billion tons were produced in China. Based on the average level of 1.7t CO2 emission per ton steel, more than 1 billion tons of CO2 generated from steel industry in China in the year. Besides the iron and steel industry, thermal power plant leads the CO2 emission in both USA and China. The total consumed electricity in China increased to 4959 billion kWh in 2012, ~70% of it was from coal fired power plant. The average CO2 emission for electricity production in the typical thermal power plant in China is around 0.78 kg kWh-1. It accounts for ~ 3.868 billion tons of CO2 emission from thermal power plant in 2012 in China."

Jan 1, 2014

By Glenio F. Daniel, Vinícius O. Barbosa, André R. Gomes, Sergio N. Monteiro, Victor B. de Souza, Frederico M. Margem

Nowadays notorious technological growth is encouraging research natural materials in substitution to more usual synthetic ones. One of those initiatives is the vegetable fibers that have been studied for the replacement of glass and carbon fibers. This research addresses broadly the study of the natural fibers mechanics properties, but none study have been made with natural fabrics, such as the pure jute fabric used in Brazil to make ropes and carpets. This work aim to evaluate the mechanical behavior of jute fabric strips with different dimensions to be used as reinforcement into polymeric composites Lots of those fabric strips were subjected to tensile tests in order to obtain the tensile resistance for each strip size. The results obtained during the tests were satisfactory and indicated that 160 × 160 × 1 mm correspond to the best result and the perfect fabric strip for the composite reinforcement.

Mar 1, 2017

By Laurent Cohen

Since the 1970s, Solvent Extraction (SX) in hydrometallurgical processes has been a key enabling technology in the production of high-purity metals. Examples include copper, rare earth oxides, uranium, cobalt and nickel. Notwithstanding incremental improvements in extractant formulations, few breakthroughs can be recounted in this industry outside of the initial amine-, oxime- or phosphine-based reagent chemistries. However, the advent of lithium-ion batteries and their stringent requirements for critical materials (lithium, cobalt and nickel) offer new challenges and opportunities for SX. Solvay recently introduced a new extractant for lithium, CYANEX® 936, and developed unique modeling software capabilities in cobalt/nickel separation using CYANEX® 272, zinc SX using DEHPA® and rare earth separations using CYANEX® 572. This paper discusses trends in SX and provides insight on processing of critical materials essential to energy sources. It also summarizes the technical and economic benefits based on extractant selection and advances in modeling.

By Jan Vrestal, Josef Tomiska, Pavel Broz

"Thermodynamic investigations on fcc solid ternary Fe-Ni-Cr alloys have been performed by means of the computer-aided Knudsen cell mass spectrometry. Ternary T.AP.-series (Thermodynamically adapted power series) are used for the algebraic representation of the thermodynamic excess properties. At 1650 K the molar excess Gibbs energy GE is negative over the whole field of stable fcc phase. The molar heat of mixing HE is exothermic in the predominant part of the fcc phase field. Only between the section with a constant ratio of mole fraction Xcr/XNi = 0.64 and the fcc phase field boundary the HE values are slightly endothermic. The results of this work can be used successfully for phase diagram calculations.IntroductionThermodynamic investigations on multicomponent alloy systems such as the Fe-Ni-Cr ternary system including the three binary boundary systems are very time-wasting and usually beset with considerable experimental difficulties. Additionally, the required experimental equipment is very expansive and the obtained results are not always satistying. Therefore it is understandable that many phase diagram calculations are based only on few experimental values of the molar excess free Gibbs energy GE. Consequently, Kundrat and Elliott [1] as well as Hillert and Qiu [2] used in their reassessments of the phase diagram of the Fe-Ni-Cr system thermodynamic data mainly assumed and/or optimized by means of various reasoning.Lee [3] reported recently, a revision of the used thermodynamic description of the Fe-Ni liquid phase is necessary to obtain a better agreement with the experimental data on the bcc/liquid or fcc/liquid tie lines and liquidus temperatures in the Fe-rich region of the Fe-Ni-Cr ternary system than in the previous assessments. This is 'in full agreement with mass spectrometric investigations of Fe-Ni alloys in the liquid and in the fcc solid phase, published earlier [4,5]. Indeed, phase diagram calculations based upon the molar excess free Gibbs energies GE obtained in these studies yield liquidus and solidus lines in excellent agreement with experimental phase diagram data [5]. Nevertheless, these experimental data have not been considered later on any more, not even in the revision by Lee [3]."

Jan 1, 1996

By M. -V. Wang

Hydrotreating and hydrorefining (HT and HDS) spent catalysts contain molybdenum, vanadium, nickel or cobalt at concentration levels that can make metals recovery economically viable. Quanzhou Jing-Tai of China has developed, through many years of operating experience in metal recovery from spent catalysts, a simple process for recovery of these metals and the production of environmentally benign residues. The process first subjects the catalysts to a low-temperature calcination step, followed by grinding of the calcine. The ground material is then leached with 10-20% v/v hydrogen peroxide to recover metals such as Mo, V and Ni or Co. This step has a selectivity that is greater than 95% for the metals. The undissovled residue, which contains mainly Ah03 and Si02, can be dewaterd and used in the production of masonry bricks. The pH of the rich liquor is then adjusted to between 0.5 and 2.5 by adding dilute sulfuric acid to co-precipitate Mo and V, with a recovery rate of greater than 99%. The lean liquor contains mostly dissolved Ni or Co, which can be recovered through precipitation at a pH of between 8.5 and 9.5 by caustic additions. The final liquor is then sent to an ion exchange step for final recovery and cleanup of residual metals. The effluent is then discharged after a simple wastewater treatment process, which has been found to meet all environmental requirements. The entire process has been found to be simple, cost-effective with minimal environmental impacts while achieving the goal of complete resource recovery from spent catalysts commercially.

Jan 1, 2000

By W. E. Wallace, J. A. Warren, D. Josell, D. Wheeler

"We present the results of experiments and modeling of flip-chip geometry solder joint shapes under shear loading. Modeling, using Surface Evolver, included development of techniques that use an applied vector force (normal and shear loading) as input to determine a vector displacement of the pads connected by the solder joint (standoff height and misalignment). Previous solutions solved the converse problem: fixed displacements used to determine required applied force. Such solutions were inconvenient for applications, where the applied force (chip weight) is known. Also, for geometric and materials studies of solder joint shapes involving multiple parameters, determining the equilibrium displacement from applied force by bracketing solutions could become computationally expensive. Measurements of solder joint standoff height and misalignment as functions of the applied force (normal and shear), solder volume and pad diameter are presented. Experiments were carried out for solder ball diameters from 0.38 mm (0.029 mm3 volume) to 0.15 mm (0.0019 mm3 volume) on pads of diameter 0.64 mm and 0.35 mm. Fitting of simulation to experimental results gave optimized values for the contact angle and surface tension of the solder which were consistent with measured and literature values. IntroductionIn packaging technology flip-chip has become an important method for attaching semiconductor devices to substrates. Generally, the chip and substrate are bumped with solder and then the chip is flipped onto the substrate and the solder reflowed to form conductive interconnects. An epoxy underfill is normally flowed between the substrate and chip to reduce the thermal fatigue on the solder joints. A flip-chip assembly is illustrated in Figure 1.In flip-chip applications, the use of an integrated underfill/solder bump system [1, 2) removes an extra process step, namely infiltration of the underfill. However, the presence of an underfill will retard the self-alignment of the flip-chip. A first step in understanding and predicting this retardation is to develop a model to describe normal and lateral force-displacements curves when underfill material is not present. At this stage it is unclear whether static surface tension theory is sufficient to describe a complete model for flip-chip realignment even without underfill."

Jan 1, 2001

By Kaixi Jiang, Lan Li, Bang Wei, Haibei Wang, Yaping Feng

"China is currently the world's largest copper producer. In the last five years, 950 kt/y of smelting capacity was commissioned. Currently, about 1200 kt/y smelting capacity is under construction and about 2000 kt/y smelting capacity is under feasibility study. Ausmelt/ISA smelting and flash smelting technologies were commonly adopted in China. After the double-flash-smelter was first adopted in 2004, three new double-flash-smelters are scheduled. Recently, two new copper smelting technologies were developed in China. One is an improved bath side-blown smelting process, and another is the SK.S bottom blowing process. Both technologies have been in practice for over three years and have achieved good technical performance. Approximately 500 kt/y new smelting capacity in China and India will adopt these technologies. Both technologies have the advantages of low investment cost, low energy consumption and high flexibility for complex raw materials. This paper reviews ""green"" copper smelting projects in China and introduces the practices of the two new Chinese smelting technologies.IntroductionPresently, China is the largest copper producer in the world. As far as the smelting of copper is concerned, there are many smelting processes applied in industrial production, such as flash smelting, Noranda smelting, Ausmelt smelting, Isa smelting, the Mitsubishi process, Vanukov smelting, silver copper-smelting, SKS smelting, both side-blown smelting, traditional blast furnace smelting, electric furnace smelting, reverberatery smelting and so on . Except the last three traditional processes that are eliminated because of their failure to meet the requirements for environmental protection, all of the other above-mentioned methods are advanced smelting processes adopted nowadays."

Jan 1, 2012

By Fatbardha Osmani, Skender Osmani

"A system analysis of the resource and environment management (water, energy etc) starts from its definition. Unfortunately, there is not a unique semantics of the mentioned concept. On these circumstances, in this paper the following issues are presented: 1.A short view on the existing concepts of management. 2.A new definition on the concept of management. It is considered as a complex and rational activity on human and natural resources ,environment etc, which starts from a analysis of infrastructure ,technology , etc, mission , alternatives , project etc. and ends to an optimal output. Basing on this definition, the management has two principal components: strategy and policy. The strategy is referred as a blue print program (the same definition as in Game Theory), which contains all the contingency alternatives. , while the policy is referred as a strategy applied into practice. The strategy is the first , while the policy is the second one. The best alternative of a policy is the project, Each strategy has one and only one project. The mentioned definition erases the differences between concept of policy and politics. Each strategy has its alternatives ,the next has its sub strategy and so on, i.e. whatever are going to be the strategy, there are a hierarchy composed by sub strategies up to the simplest strategies applied by a single individual (human beings or robots). The strategy objectives are necessary and sufficient conditions for its realization i.e . the strategy is an optimal activity, in which all resources are integrated and processed . Several strategies could be joined into one( for example the surface water strategies of the Balkan countries) . In this view, the strategy could be globalized into optimal way basing on different criteria’s as social, economic, environmental, their risks and effectiveness etc. etc An example from the water management illustrates the mentioned concepts."

Jan 1, 2008

By A. L. Paverd

The petrology of a number of pyrometasomatic mineral deposits in north Queensland, Australia, were studied to evaluate the use of mineralogy and major element chemistry in the exploration for copper, lead and zinc-bearing skarns. Results indicate a direct correlation between the character of the mineralization and the composition and nature of the host rock. The study of garnet compositions proved the most useful. Economic mineralization was limited to limestone-derived skarns containing garnet of And60-90, whereas skarns containing garnet of less than contained less than 1And55 contained less than 1% total sulfide. Skarns containing garnet of And60-8S host the best mineralization; above And8S&apos; copper, lead and zinc sulfides decrease and magnetite and pyrrhotite become the dominant ore minerals. Similar correlations were found for pyroxene, amphibole and &apos;the bulk composition of the skarns.

Jan 1, 1981