Search Documents

The Pogo Mine, near Delta Junction, Alaska is a 2500 TPD gold operation employing processes including grinding, gravity, rougher flotation, leach, CIP, and E/W. An OCS(Optimizing Control System) expert control system has been implemented on rougher flotation in early 2008. The OCS system communicates with the Plant DCS(Distributed Control System) through OPC(OLE for Process Control) communication. The initial strategy was to control the flotation cell froth level set points to achieve target froth velocities. This strategy was enhanced by controlling both level and air flow setpoints. The flotation cell air and level are adjusted to reach cell pulling rates (froth velocities). The pulling rate setpoints for each cell are determined based on downstream capacity (concentrate surge tank level). The effect of pH and upstream disturbances is also taken into account in adjusting the air and level setpoints. Feed forward compensation is employed down the flotation row to minimize disturbances.

Jan 1, 2009

By Harry Asche

The last 12 months has seen the construction of the first Earth Pressure Balance (EPB) TBM excavated tunnel in New Zealand on the Project Hobson sewer storage tunnel for Watercare Services Limited, with the concurrent excavation of the second EPB tunnel on the Rosedale Outfall project for North Shore City Council. Together these tunnels involve a total length of 6km and follow an 8 year pause in TBM activity in Auckland. TBM performance on these two projects is thus of significant interest as there are four major tunneling projects totaling over NZ$8B being planned for Auckland, in similar ground conditions. Auckland?s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20km of the city centre. The paper describes the design and construction challenges for the projects, including TBM performance, ?sticky spoil? management, and risks associated with basalt lava flows and two paleovalleys. Watercare?s Project Hobson also saw the successful implementation of a Geotechnical Baseline Report?one of the first uses of this type of document in Australasia. Rosedale Outfall is designed for high internal water pressures with varying hydraulic flows, with the risk of exfiltration explicitly addressed.

By M. E. Smith

Waste rock dumps, tailings impoundments and spent leach heaps are common features at mine sites. Many of these waste disposal facilities contain sulfide-rich minerals, which generate acid mine drainage (AMD) when they oxidize. Control of AMD can be achieved by removing one or more of the three essential components in the acid-generating process (sulfides, air, or water). One AMD prevention measure is to cap the waste with an engineered cover system to minimize the infiltration of water and diffusion of air into the system. Possible cover designs include: ? Earthen ?store-and-release? covers (also known as evapotranspiration (ET) or water balance covers), including capillary barriers. These covers require climate conditions where there is both modest to little rainfall and significantly greater evapotranspiration than precipitation, both annually and seasonally. ? Low-permeability compacted clay liners (CCLs) employing fine-grained soils typically compacted at wet of optimum water content. ? Geosynthetic composite covers, comprised of a geomembrane liner placed over and in direct contact with either a CCL or a geosynthetic clay liner (GCL). These systems have been commonly used for base liners for leach pads as well as covers and base liners at municipal solid waste (MSW) landfills in the US for more than 20 years. Comparisons of these different cover systems, both in terms of performance and cost, are presented later in this paper. First, however, a review of the typical mine closure approaches, and the possible rationale behind them, is warranted.

Feb 27, 2013

By S. Slottee

The technology of making and using ?paste? from mine tailings is increasingly well known by the minerals industry. The primary applications are water recovery and ?stacking? of tailings with minimal use of dams and ponds. This paper highlights some applications, other than water recovery and stacking, that have come to the attention of a paste thickener equipment supplier. As generated by thickeners, paste (also called ?thickened tailings?) is a non-settling, relatively high concentration, suspension of solids that can be pumped. Paste deposits with an angle of repose, allowing minimal use of dams. High solids concentration allows more water recovery at the paste thickener than is achieved in conventional and high rate slurry tailings thickeners. This paper is based on paste as produced in a flow sheet that includes a thickener, underflow pumps that are typically centrifugal, transfer pumps that can be centrifugal or positive displacement, and a distribution system at the deposition site. Examples of paste applications other than water recovery or stacking include: ?mine? an existing tailings pond by removing slurry, recovering coal or iron ore values, and return the new tailings to the pond as a paste that does not res-suspend; use paste to seal an existing tailings pond from leaking to groundwater or to an underground mine; extend the life of an existing tailings pond by thickening the tailings to paste; move an existing dry tailings impoundment to a new location by slurrying, pumping, paste thickening, and redeposit; minimize the size of a filter by paste thickening the feed; operate a paste thickener and filter in parallel on a tailings stream with re-mixing to achieve a high solids concentration. The use of paste tailings technology has been expanding over the last 15 years. The applications, both implemented and under consideration, are increasingly diverse and include all minerals tailings. Tailings handling designers should always consider a paste option to the conventional slurry solution.

Jan 1, 2011

By D. M. Abbott, H. J. Sandri

The geoscience matrix method has proven useful for valuing metallic mineral properties lacking delineated mineral resources or reserves. However, the method explicitly excludes commodity markets from the factors considered; marketability is assumed. When valuing industrial mineral properties, marketability cannot be assumed, it must considered. Market considerations may also significantly affect the standard weightings of geoscience matrix parameters such as the proximity to known deposits. In some cases, such proximity is desirable but in many cases it is undesirable. Application of the geoscience matrix method to industrial mineral properties therefore requires thoughtful, market-related adjustments to the basic geoscience matrix methodology.

Jan 1, 2000

By H. K. Lin

Deepwater discharges of sulfide flotation tailings have been practiced for several decades. Oxygen penetration and organic matter content in such environments are the two major factors that determine their reduction-oxidation condition and hence the rate of sulfide mineral dissolution under such discharge environments. In this study, the effects of solution redox potential and pH on the dissolution of some heavy metals from sulfide flotation tailings were examined. Zn, Pb and Cu concentrations in solution were all higher at a higher redox potential and lower pH. Dissolved Zn concentrations reached 100 ppm even at a low redox potential of 105 mV and near neutral pH after 33 days. Pb concentrations were below 2 ppm at 105 mV and near neutral pH after 165 days. At 105 mV, the Cu concentrations were below 0.2 ppm at near neutral pH after 165 days. At pH 2.3, the Fe concentrations were higher at 420 mV than at 105 mV. But at pH 6.8, the Fe concentrations were lower at 420 mV than at 105 mV, due to the oxidation of Fe2+ to Fe3+ and the subsequent precipitation of ferric hydroxide. Arsenic concentrations in solution were all less than 0.002 ppm. For Zn, Cu and Fe, no significant differences were observed between the tests in solutions prepared using seawater and those using distilled water. However, Pb concentrations reached higher levels in solutions prepared using seawater.

Jan 1, 2009

Newmont Gold's methods for deposit modeling vary, depending on geology, mining and processing methods, economic feasibility and availability of historical information. It is argued that successful modeling requires understanding these factors, knowing the strengths and weaknesses of the various modeling techniques and being flexible in selecting the appropriate methods. Newmont is one of the world's largest gold mining companies, with operations in the United States, Peru, Mexico, Indonesia and Uzbekistan. And it is active in exploration worldwide. At the end of 1996, Newmont declared a total reserve of 1.15 equity kt (37.1 million equity oz) of gold and 2.17 equity Mt (2.39 million st) of copper. The gold deposits managed by Newmont totaled 752 Mt (829 million st) of ore containing 1.28 kt (41.3 million oz) of gold averaging 1.71 g/t (0.05 oz/st). In addition, Newmont is developing a porphyry copper-gold deposit that totals 9.1 Gt (1 billion st) of ore containing 380 t (12.1 million oz) of gold and 4.82 Mt (5.32 million st) of copper. (In May 1997, Newmont Gold Co. merged with Santa Fe Pacific Gold Corp., thus increasing Newmont's reserves to 1.72 kt or 55.2 million oz of gold and 2.17 Mt or 2.39 million st of copper.)

Jan 1, 1998

By K. L. Lownie

For research and test data to serve a useful purpose, it is essential that it be derived from some known standard test procedure that allows for comparative analysis as well as independent replication and verification. Fan performance data provided by manufacturers is not absolute, and is influenced by the geometry of the test installation. For these reasons, fan test standards have been prepared in order to establish a clearly defined test procedure that allows for comparison of different fan designs, and also allows for the independent verification of test data. Internationally recognized Standards such as BS848, ISO5801, and AMCA 210 etc. are highly prescriptive, and precisely specify test duct configurations, measurement procedures, measurement planes and instrumentation to be used. Provided the laboratory tests are conducted strictly in accordance with the relevant Standard, the performance data will accurately reflect fan performance within the appropriate tolerances for efficiency, pressure and flow when tested in the defined configuration. Major differences in performance exist between a fan tested in accordance with a Fan Test Standard, and an identical fan installed in a mine ventilation system. The aerodynamic performance of any fan will be influenced by the quality of the fan manufacture, the flow system within which it is operating, the location of measurement planes, and the system stability. The flow distributions present in a standardized Laboratory test are unlikely to be repeated in mine ventilation systems, and this will also disadvantage fan performance. Unless the fan supplier takes all of these influences into account, there will an inevitable reduction in fan aerodynamic performance, and the end user will experience a shortfall in expected flow through the mine. The effect on fan performance can range from minor inconvenience to catastrophic fan failure resulting in major rectification costs and significant loss of mine production.

Jan 1, 2009

By A. Cole, F. Porretta

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

Jan 1, 2002

By S. Ragab

The objective of flotation models is to predict the recovery rate of minerals from a flotation cell. In this paper a CFD?based flotation models is presented. The model uses first order rate equation, and the collision frequency is estimated using Abrahamson [1] model with input from CFD two-phase simulations. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) are determined by the two-phase hydrodynamic simulations. Knowing these parameters throughout the machine is essential in understanding the effectiveness of different components (rotor, stator or disperser, jets) on the flotation efficiency. Not only the average pulp recovery rate can be estimated but also the regions of high/low recovery rate can be identified. The CFD-based flotation model presented here can be used to determine the dependence of recovery rate constant at any locality within the pulp on particle diameter, particle specific gravity, contact angle, and surface tension.

Jan 1, 2012

By Jack A. McQuiston, Thomas A. Cross

Corrosion of equipment and machinery in the coal industry is usually the result of three main agents: acids, chlorides, and abrasion. Acids and chlorides are especially troublesome in coal preparation plants where soluble salts and sulfur in the coal produce a highly corrosive wash solution. Abrasion is common in all operations where coal is handled or conveyed. Together, the acid-chloride-abrasion combination results in some of the worst corrosive conditions found in any industry. The variety of equipment and structures in the coal industry calls for different corrosion control techniques. Table 1 lists the areas of concern for a number of items. Just as there is a wide variety of corrosion problems, there is a wide array of coating materials available. Tables 2 and 3 are selection charts to provide guidance in narrowing down the choices. Experience has shown that a limited number of coating systems work best on coal equipment and structures. These systems are described in Table 4. The good-better-best designation in the table refers to coating system longevity. Good indicates the least costly and shortest service life. In nearly all cases the lowest annualized cost can be achieved by using the coating system rated best, due to the avoidance of costly repaints and unnecessary downtime. The most expensive coating system, though, is worthless unless the coating system is properly applied. Field inspection to insure compliance with specifications is an important aspect, and is a service available from many coating suppliers. Even the best coating systems require periodic maintenance to achieve satisfactory results. Spot rusting from mechanical damage should be repaired annually to maximize the coatingsystem's results.

Jan 2, 1980

By M. A. Stoakes, H. D. S. Miller

Surface subsidence is becoming an increasingly important factor in the economics of mining Louisiana salt domes due to, amongst others, excessive shaft deformations and land loss to encroaching sea water. The vast majority of subsidence studies have been undertaken on bedded, tabular deposits. It is important to understand the causes of subsidence due to mining domal salt and how it can be minimized. The paper will review the major differences between subsidence caused by domal and tabular evaporite mines, the problems encountered in predicting subsidence, the factors that influence subsidence and, finally, possible alternative mining methods.

Jan 1, 1986

By S. G. Gendler

The choice of ventilation schemes in the Northern Mujsky railway tunnel and definition of the nec-essary quantities of air ensuring regulated radiation conditions in the tunnel system has been accomplished. The influence of natural draught on the stability of tunnel ventilation has been estimated. The design of a portal venti-lation gate allowing minimal influence from natural factors is described. The dependence of pressure loss in the sliding ventilation gates on their spanning value of the vehicle tunnel section has been determined. The selection of parameters for an atmospheric air heating system in winter has been carried out. The operation regimes of air heaters, dependent on the temperature of atmospheric air, have been established.

Jan 1, 2009

By A. Martin

Detailed porewater profiles of arsenic and other interstitial metabolites were used to assess the relationship between trophic status, sediment redox chemistry and arsenic mobility in a historic tailings repository. The results demonstrate that in eutrophied systems which exhibit greater sediment oxygen demand, the depth of the Fe(III) redoxcline, and hence depth of arsenic release, may lie in close proximity to the sediment-water interface. As a result, arsenic scavenging mechanisms are significantly reduced, resulting in a greater flux of arsenic to the water column. Such considerations have important implications for the management of pit lakes, tailings ponds and contaminated lakes which may consider: 1) the discharge of sewage to the water body during operations; and/or 2) post-closure fertilization as a remediation strategy.

Jan 1, 2002

By D. R. Wilburn

The worldwide budget for nonferrous, nonfuel mineral exploration was expected to increase by 58 percent in 2004 from the 2003 budget, according to Metals Economics Group (MEG) of Halifax, Nova Scotia. The increase comes two years after a five-year period of declining spending for mineral exploration (1998 to2002). Figures suggest a subsequent 27 percent increase in budgeted expenditures from 2002 to 2003. For the second consecutive year, all regional exploration budget estimates were anticipated to increase. The worldwide budget for gold exploration achieved about 50 percent of the total amount budgeted in 2004.This was 68 percent, or US$715 million, higher than the reported 2003 budget. The 2004 worldwide exploration budget estimates for copper increased by 70 percent, orUS$237 million, to US$577 million from the 2003 budget. The budget for nickel exploration increased 52 percent, or US$89 million more than in 2003. The 2004 exploration budget for other mineral targets (primarily cobalt, heavy minerals, industrial minerals and silver) increased114 percent, or US$118 million.

Jan 1, 2005

By Georgy Cherkashov, Svetlana Babaeva, Tamara Stepanova, Firstova. Anna

Seafloor massive sulfides (SMS) study in the Russian Exploration Area at the northern equatorial Mid Atlantic Ridge began after signing the contract with International Seabed Authority in 2012. In order to evaluate the SMS resources in the course of exploration the major and rare metals with economic value should be determined. The evaluation is based on geochemistry and mineralogy and particularly on the type of rare metals occurrence in the SMS. As a case study research of the Semyenov cluster of SMS deposits have been conducted.

Sep 1, 2014

By J. L. Carr

Continuous mining machines are extensively used in the underground coal mining industry. These machines are typically remote-controlled, and severe injuries and fatalities occur every year when a miner is struck or pinned by the machine. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Researchers at the National Institute for Occupational Safety and Health (NIOSH)have developed the Intelligent Proximity Detection (iPD) system to provide enhanced protection while minimizing false alarms. The iPD system uses a set of pre-defined rules to determine which machine motions are safe and which would present a potential hazard, and automatically disables only the potentially hazardous motions. This system has been installed and tested on a Joy 14CM continuous mining machine at the NIOSH Office of Mine Safety and Health Research in Pittsburgh. Under laboratory conditions, the achievable accuracy and performance of the iPD system has been quantified with respect to a number of variables including position of the conveyor boom, presence of the machine?s trailing cable, and orientation of the miner-wearable component. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By William R. Yernberg

The 2006 North American Tunneling (NAT) Conference was held June 10-15, 2006, in Chicago, IL. The biennial conference was the first NAT conference by the newly formed Underground Construction Association of SME (UCA of SME). The UCA of SME was formed earlier this year at the request of members of the American Underground Association (AUA) (ME, April 2006, page 75). The conference included a keynote session, technical programs, workshops, a trade show and social activities. The conference exceeded expectations with 570 attendees. They included engineers, equipment manufacturers, representatives from government agencies and other interested individuals in the underground construction industry. The trade show was also a success with more than 86 booth spaces sold. Vendors included the biggest names in the underground construction and tunneling industry and included equipment manufactures, construction contractors and engineering companies. The trade exhibition provided a forum for interested parties in the tunneling industry to meet and discuss services, equipment and techniques.

Jan 1, 2006

Due to the ongoing restructuring of the mining industry in central Europe with a continuous decline of the number of large underground mines and collieries, and a simultaneous decline of staff numbers in the remaining mines, the established mine rescue schemes are endangered to collapse. With the end of the mine rehabilitation at Wismut Uranium in 2014, the last remaining major mine rescue teams in Saxony, providing basic mine rescue services for all other mines in the region, will disappear. This will leave a large number of small mines and other underground operations without capable mine rescue support. Since none of these companies is able to set up a complete mines rescue unit on its own, new ways have to be found. Among others, a central mine rescue team for central Germany as well as the assistance by special trained professional fire fighters or mine rescue teams from abroad are discussed. Problems like location of the central rescue team, financing, communication and transport have to be solved. This paper provides an overview over the complexity of the problem as an example for other mining regions worldwide and will discuss national and cross-national strategies.

Feb 23, 2014

Collaboration between education providers is the key to long-term sustainability and improved quality in mining education. The mining industry is now, more than ever, an industry doing business on a global basis. Staff are recruited by global mining companies in many different countries and can find themselves deployed anywhere in the world. The mining engineer of tomorrow must be willing to take on this international challenge, and must be educated to a level where he or she has a comprehensive grounding in technical aspects of mining engineering, but also a well-founded appreciation of management, social, environmental and cultural issues that may be encountered around the world. In order to deliver such an education, academic providers must collaborate at both a national and international level. This paper provides an overview of progress that has been made in Australia through the national joint venture ? Min¬ing Education Australia (MEA). Supported by the mining industry in Australia, through the Minerals Council of Australia (MCA), MEA has been operational since 2007 and is seeing the development of a range of innovative courses and delivery methods, together with a high level of staff cooperation across the country. MEA has also commenced some international teaching initiatives that are seen as a catalyst for a far greater degree of international collaboration in the future. Such activity is not only to the benefit of the students who are taught by experts from around the world, but it also ensures that individual univer¬sity programs remain viable in terms of staffing numbers and financial performance. The paper also presents some statistics on recent upward trends in mining engineering student numbers from around the world, in response to the global shortage of mining engineers.

Jan 2, 2010