Search Documents

By D. S. Kingery

The practice of using doors to control main ventilating currents in bituminous-coal mines is common throughout the industry. When doors are erected in pairs to form air locks, they are usually accepted as satisfactory by both State and Federal coal-mine-inspection agencies. A review of the contributing factors in recent methane ignitions showed that interrupted ventilation (often caused by doors latched open, destroyed, or damaged) was the principal cause of methane accumulations that subsequently were ignited.

Jan 1, 1958

By Joseph Cervik, Maurice Deul, Albert Sainato

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pct; reductions of 38 to 79 pct were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No. 3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By C. M. McCulloch, Maurice Deul

A geologic study of Mines 32 and 33 in Cambria County, Pa., was conducted as part of a methane control research program. Areas of high methane emission and roof instability are encountered which are related to the structural and stratigraphic features that characterize the geologic setting of these mines. Locally the folds trend N 20° E ±2°, the direction of the butt cleat in the Lower Kittanning coal. The face cleat strikes at N 69° W ±2° and the systematic rock joint in the surface bedrock strikes N 67° W ±2°This suggests that a directional stress oriented N 70° W produced the folds and influenced the directions of coal cleat and systematic joint sets. Analysis of SLAR indicates three directions of prominent regional lineation: N 39° E, N 31° W, and N 70° W. Little gas was encountered during development mining; large volumes of gas are encountered when roof falls. Most of the gas comes from strata above the mined coal; therefore, to control methane, roof instability must be controlled. Roof falls and high rates of methane emission are most likely where less than 30 feet of many thin layers of limestone, shale, and sandstone occurs between the Lower Kittanning coal and the next coal and in zones along the margins of a sandstone channel.

Jan 1, 1973

By Ronald H. Church, Walter E. Pittman, J. T. McLendon

In its role of providing technical assistance to the mining industry, the Bureau of Mines' Tuscaloosa Research Center has conducted research to develop trapped miner location systems which would aid in locating miners trapped by underground mining disasters. Efforts to produce electromagnetic systems for the location of trapped miners underground and to communicate with them were surveyed, from the 1920's to 1981. Theoretical studies of through-the-earth electromagnetic transmissions are described as well as studies of the electrical characteristics of various rocks, minerals, and soil. Several trapped miner location systems are reviewed including the Westinghouse systems, the DEVELCO system, and an automated three-dimensional location system, and the phase difference of arrival technique. Tangential research, relevant to trapped miner location systems is described. A comprehensive bibliography covering all aspects of trapped miner, through-the-earth electromagnetic location and communications systems is appended.

By A. Sainato, S. J. Kravits, G. L. Finfinger

This Bureau of Mines report describes and compares the procedures, capital investments, and operating costs of rotary and in-hole motor drilling techniques used to drain methane gas from the Pittsburgh Coal- bed in an underground mine located in southwestern Pennsylvania. A timestudy was conducted during the drilling of each of two boreholes, and the data were collated to serve as a base for comparing drilling procedures and operating costs. Findings indicate that drilling with an in-hole motor offers four advantages over rotary drilling; namely, an increase in drilling productivity, fewer worker-hours required, ease of maintaining vertical and horizontal bit trajectory, and less expensive drilling cost per foot of borehole.

Jan 1, 1985

By William H. Pomroy, Shail J. Butani

"This Bureau of Mines publication presents a statistical analysis of official U.S. Mine Safety and Health Administration (MSHA) metal and nonmetal mine fire reports from 1950 through 1984, plus accounts of selected nonreportable fires (less than 30 min and no injury) and opinion data on fire hazards from mine safety directors. Fires were analyzed by time trends, ore type, ignition source, burning substance, location in mine, equipment involved, means of detection, duration, number of injuries and fatalities, mining method, and successful extinguishing agent. The leading ignition sources were electricity in underground fires and engine heat in reported surface fires. The most frequent burning substance was combustible liquids for all nonreportable fires, reported surface fires, and reported underground fires from 1978 to 1984. For underground fires reported prior to 1978, timber was the leading burning substance. Mobile equipment was the type most frequently involved in both underground and surface fires. Underground fires occurred most often in haulageway or drift areas, and reported surface fires occurred most often in plant and mill buildings, while most nonreportable surface fires occurred in other areas. The most common methods of extinguishment were water hose lines for reported fires and dry chemical handportable extinguishers for nonreportable fires. INTRODUCTIONIn support of the Bureau of Mines research on mine fire protection, two separate baseline studies on mine fire incidents have been prepared. The first study addressed coal mine fires. The results of that study are summarized in the Bureau's Information Circular 8830, ""A Statistical Analysis of Coal Mine Fire Incidents in the United States From 1950 to 1977."" This second report, addressing metal and nonmetal mine fires, is the companion to IC 8830. Together, these two reports provide a comprehensive, factual summary of the mining industry's fire experience.This report, like IC 8830, covers (1) MSHA fire incident reports, (2) records of nonreportable fires (less than 30 min and no injury), and (3) mine safety directors' opinions on fire hazards. The MSHA fire reports provide the most reliable, objective, and accurate historcial record of the major noncoal mine fires that occurred during the study period (1950 through 1984). However, MSHA fire reports alone understate the true magnitude of the fire problem because metal and nonmetal mines have been legally required to report fires to MSHA only since 1968. Although some fires were reported prior to 1968, doubtless a great many were not. Also, the reporting regulations that took effect in 1968 specify that only fires lasting 30 min or longer or involving an injury need to be reported. MSHA fire reports are thus limited in scope by MSHA's legal authority. In order to provide a more comprehensive data base, it was also necessary to gather and analyze mine company records of nonreportable fires."

Jan 1, 1986

By Bergerm L. B., S. J. Davenport

"INTRODUCTION Oxygen, because of its vital relationship to man's physical well being, is the most important chemical_ element. It may be breathed, however, only in a rather limited range of concentrations and pressures without producing ill effects. An excess of oxygen may be equally as harmful as too little of it. Because of the importance of these effects, the study of the physiological action of oxygen has received attention for many years and by many investigators. Much of the investigative work has been directed toward determining the limits within which oxygen in abnormal concentrations and at abnormal pressures may be breathed with safety in such applica¬tions as deep-sea diving, work in comprossod-air, aviation, the wearing of apparatus designed to permit entrance into irrespirable atmospheres, and in the therapeutic applications of the medical profession.The Bureau of Mines frequently receives requests for information on the effects of breathing essentially pure oxygen, because of the Bureau's association with the use of self-contained oxygen breathing apparatus for entering irrespirable mine atmospheres, and the use of oxygen in conjunction with artificial respiration as a moans of resuscitation. The purpose of this paper is to summarize briefly the effects upon the human body of the inhalation of oxygen in various concentrations and at various pressures and to give reference to other published information that deals in greater detail with the diverse phases of the subject. The literature in this field is voluminous; therefore, a complete bibliography has not boon presented in this paper. No paper on this subject would be complete without reference to the classic pioneering work of Paul Bert (1) 3/ in this field. Articles such as those of Stadia, Riggs, and Haugaard (2), Bean (3), Specht (4), and others cited contain extensive lists of references that will leadthe reader to information in a degree of detail that is not within the scope of this publication."

Jul 1, 1950

By C. B. Manula, R. L. Sanford, R. A. Rivell

PART I. FLOW CHARTS

Jan 1, 1974

By Michael G. Pojar, John K. Ahlness

"The copper industry has had a long and interesting history associated with leaching, involving vat, dump, heap, and in situ methods. The Bureau of Mines has also had an interest in copper leaching and has researched the techniques of solution recovery, particularly concentrating on in situ methods. In situ mining is a relatively low cost method and has been proven commercially successful by nine operations. It has been most commonly used for final recovery in old workings at the conclusion of conventional mining operations.This report brings together information about 10 commercial in situ operations as well as 14 experimental projects. These 24 sites comprise most of the in situ copper mining activities that have taken place in the United States. Background information, geology, ore preparation, solution application, and recovery and processing are provided for each operation. Production data and tables summarizing the engineering statistics for each operation and an extensive in situ mining bibliography are included. INTRODUCTIONThe purpose of this Bureau of Mines report is to summarize the documented in situ copper leach mining activities that have taken place in the United States. It was prepared to provide a source of engineering and operating data upon which future in situ copper mining activities can be based. Twenty-four different sites are discussed. These are all of the sites that are known to the authors from the extensive in situ copper leach mining bibliography developed at the Bureau's Twin Cities (MN) Research Center (Appendix B).In situ copper leach mining activities fall into the following categories:1. Commercial operations with ore body preparation.2. Commercial operations in old mine workings.3. Experimental programs.Ore body preparation includes such activities as blasting, block caving, and hydraulic fracturing (hydrofracing) specifically to fragment the ore body. Operations in old mine workings include those done in open pits, worked out block caved areas, and backfilled stopes where leaching is done as an afterthought to conventional mining. Experimental programs are small-scale tests of the feasibility of a commercial operation. Some of these programs did not progress to the point where leach solutions were applied to the ore.Each operation (locations shown in figure 1) will be discussed in terms of background information, geology, ore preparation, solution application, recovery and processing, and engineering and production data. Information was collected from published reports, communications with company personnel, and site visits."

Jan 1, 1982

By Lloyd A. Morley, Robert Stefanko

Table

Jan 1, 1974

By Karl C. Dean

The Bureau of Mines studied the precipitation of copper from dilute acidic sulfate solutions using shredded automobile scrap in a rotary drum. The tests established that the scrap in the rotary drum precipitated copper faster and more completely than shredded, detinned, tinplate scrap in a launder, with comparable iron consumption. Although power is required to rotate the drum, the faster precipitation and continuous recovery of cement copper are advantages of the tumbler method. Cost evaluation indicates that the rotary drum method, which uses relatively low-cost and readily available shredded automobile scrap, is competitive with the launder method, which uses relatively high-cost shredded tinplate scrap or detinned shredded cans.

Jan 1, 1968

By Robert J. Timko

The objective of this Bureau of Mines research work was (1) to determine how well the E. I. Du Pont de Nemours and Company P-2500 personal dust sampling pump controls the flow rate at 2 L/min and (2) to compare respirable dust mea-surements made using the P-2500 with those made using a nonpulsating sampling flow system, both using the Dorr-Oliver 10-mm nylon cyclone dust size classifier. The calibrator and the operation manual for the P-2500, supplied by the manufacturer, were also evaluated. Flow tests consisted of long-term (6-to 8-hour) flow stability tests at various backpressures, a low-flow indicator examination, flow controller response time tests and pulsation tests. Dust tests were performed using coal, silica, and Arizona road dust. No tests were performed to examine effects of temperature, barometric pressure, vibration, or mechanical shock. These pumps performed well within manufacturer specifications in all tests.

Jan 1, 1982

By Loyal Clarke, H. H. Storch

"The discovery of large deposits of polyhalite (K2S04.MgS04.2CaSO4.2H2O) in Texas has led to an investigation of possible industrial proecsses for the extraction of potash from this material. This mineral was first discovored in small quantities in the European potash deposits in or about the year 1800. Chemists fire thought it to be a form of calcium sulphate, but a more accurate analysis by Strohmiyer indicated the composition as given by the above formula.The decomposition of polytalite by aster is very slow and results in the formation of a layer of gypsum at the surface of the polyhalite which retarts the solution of the potaseium and magnesium sulphates. To obtain a substantial yield of K2S04 in solution it is necessary to use large amounts of water at room temperature, for he concentration of K2S04 is limited by the low solubility of syngonite (K2S04.CaS04.H2O) whereas at 100º C. several days boiling are necessary to obtain more than a 6 per cent K2S04 solution even when finely powdered polyhalite is employed.In 1854 H. Rose discovered that calcination, followed by leaching with water, resulted in a larger extraction of the potassium and magnesium sulphates, as compared with leaching without precalcination. During the course of a series of investigations concerning formation of oceanic salt deposits, Van't Hoff and his pupils obtained sufficient data to construct the equilibrium diagram for the system K+Mg+SO4--Ca++.H2O for 25° C. and for 83° C. These data are very well summarized. in the International Critical Tables' and by Boeke and Eitel. From a consideration of the diagrams for 83º C. one would conclude that an extraction of polyhalite with moderate amounts of water at 33º C. would result in a solution whose maximum concentration of K2So4 would be about 3.6 grams per 100 grams of water and of M2SO; about 4.0 grams per 100 grams of water, corresponding to equilibriumwith the solid phases: Polyhalite potassiam-calcium pentasulphate and anhydrite.The fact that it has been found possible to obtain as high as 11.4 grams of K2S04 per 100 grams of water (see table 6) and an equivalent amount of MgSo4 (8.1 grams per 100 grams of water was obtained corresponding to a ratio K2/Mg of 0.98; indicates that the formation of these complex salts is very slow. To be sure, this results was obtained at 100° C. instead of 83º C. However, the work of Anderson and Nestall 9 on the double salts of calcium and potassium sulphates at 100º C. indicates that the diagram at 100º C. C. would not be greatly different from that at 83º C. This slow rate of approach to equilibrium when combined with precalcination of,of polyhzli-,a is the 17,asis of some of the more p:olisinE methods of extracting potash from polyhalite."

Jun 1, 1930

By P. G. Barnard

The Nation's steel industry is largely dependent on shipments of manganese from foreign sources for steel production. An adequate substitute for the manganese requirements of our present steel technology would improve our national self-sufficiency and also contribute substantially to the conservation of our manganese resources. As each of these objectives is a major interest of the Bureau of Mines, possible substitutes for manganese in steel were investigated. Titanium was selected as the most promising substitute because the published results of several investigations indicate that titanium would perform the most obvious function of the manganese in steel: The elimination of iron sulfide and its deleterious effects. The investigation involved extending the published data on titanium additions in steel to provide enough information for an accurate evaluation of the practical value of the substitute. Therefore, quantitative data were obtained on the partition of sulfur and carbon between iron and relatively small titanium additions.

Jan 1, 1962

By W. N. Poundstone, W. M. Merritts, B. A. Light

A joint investigation by the Bureau of Mines and the Christopher Coal Co. at the Humphrey No. 7 mine, operating in the Pittsburgh coalbed in northern West Virginia, was undertaken to gain more insight concerning the hazardous emission of methane gas in mining. This report describes the equipment, procedure, and results. Horizontal bleeder holes drilled in the faces drained large quantities of methane, eliminating downtime of mining equipment. Also, larger quantities of methane were removed by forcing 14 to 25 g,.p.m. water at 25 to 200 p.s.i. 5 pressure into the bleeder holes. In one infusion test a fluorescein dye was added to the infusion water; in later mining operations, the infusion water was traced for a distance of 1,500 feet. With vacuum pump applied to the horizontal hole the gas-flow rate increased, and the methane content decreased. Tests indicated that methane and water infused in bleeder holes traveled along the bedding planes of the Pittsburgh coalbed at a faster rate than across the planes. Methane associated with coalbeds is produced by the slow decomposition of carbonaceous material in the absence of air and the presence of water. It is lighter than air and, depending on its concentration, forms an inflammable or explosive mixture with air. It is believed that methane is entrapped in and around the pores of the coal and adjacent strata--often under great pressure. In many cases where the strata have been disturbed by geologic movements the

Jan 1, 1962

By W. P. Stroud

In this U.S. Bureau of Mines report, the conditions required for the direct reconstruction of a tomogram from observed line integrals are examined. Because of the limited access to the working faces in coal mines, the special case of access to only two opposite faces is emphasized. Classical matrix methods were used for small dimensional (2 by 2, 3 by 3, and 4 by 4) applications to determine the limitations and the requirements for a solution. The results for large (n by n) grids were then inferred and generalized from those of the smaller grids and matrices. Limited access tomography is found to be appropriate for in-seam hazard detection from seismic and microwave data, but it is shown that additional data must be added to obtain a direct solution.

Jan 1, 2010

By A. C. Fieldner

The Bureau of Mines has recently conducted a study of results obtained in analyzing similar samples of coal and coke by 25 laboratories throughout then country, in comparison with results obtained in the Bureau's coal laboratory at Pittsburgh. The purpose of this work was primarily to obtain a comparison of the methods of coal analysis used by the laboratories of the American Gas Association. Therefore, four standard samples of coal end one of coke ware prepared in the Bureau of Mines coal laboratory at Pittsburgh, and portions sent to each laboratory. At the same time, a like number of standard samples were submitted to 12 commercial laboratories rot affiliated with the Association, for the purpose of comparing their analyses with the results is obtained by the U. S. Bureau of Mines and the American Gas Association. Tire comparison is based on the average of 24 analyses by the Bureau of Mines on each kind of coal, and the accompanying curves show the deviation from this average analysis, together with deviations from the check limits of the American Society for Testing Materials.

Jan 1, 1923

By Wing G. Agnew, John A. Johnson, McHenry Mosier

"INTRODUCTION AND CONCLUSIONSThe first three reports of investigations 5/ in this series, pertaining to the investigation of stemming at the Mount Weather Testing Adit dealt with the dust produced by blasting, the effect of stemming on gases generated by blasting, and the relative advantages and disadvantages of different types of stemming and no stemming when used with 60-percent ammonia gelatin dynamite.This report covers an investigation of the length of stemming material through which a primer will fire and detonate a charge of dynamite, such as a missed hole.The practice of drilling a new hole a foot from a missed hole to blast out the missed hole should be prohibited. It is dangerous, as is evidenced by the number of miners killed through drilling into missed holes. It is even more hazardous in a mine on a multiple-shift basis, in which the same miners do not drill succeeding rounds."

May 1, 1942

By Robert H. Schutz

This publication lists and describes devices approved jointly by the Secretary of Interior and the Secretary of Health, Education, and Welfare, under the provisions of [§]70.300-1, Part 70, Subchapter 0 of Chapter I, Title 30, Code of Federal Regulations (35 F.R. 5548, April 3, 1970), for use as respiratory protection against respirable pneumoconiosis-producing dusts. Included are type C supplied-air respirators approved under Bureau of Mines Schedule 19R and dust, fume, and mist respirators approved under Bureau of Mines Schedule 21B.

Jan 1, 1971

By George S. Rice

There have appeared, from time to time, comparisons of various features of coal mining practice in the United States and Great Britain. A recent, article, appearing in a British journal, points out that the American miner produces 3 1/2 times as much coal per shift as the miner, at one-half the cost, and proceeds to explain the natural industrial, and engineering causes which lead to this result. Amon« he reasons advanced. is that the American coal miner enjoys the advantage of more easily worked seams of coal, due to the fact that the coal mining industry in the United States is of more recent date than in Great Britain. The latter qualification is not correct, because where these advantages exist, they will persist. The coal beds of the United States are not buried deeply, except in the remote parts of the country, as in the Uinta Basin of Utah. The article referred to states that many of our miners are still employed on out seams reached by "adits", (which we term entries), or by vertical shafts of moderate depth. It is probable in fact that the great bulk of the coal of the United States is taken out from a depth of less than 400 feet.

Mar 1, 1920