Search Documents

By A. G. Smelley

As part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U. S. Department of the Interior, is developing a dewatering technique that allows for disposal of phosphatic clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weightnonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater phosphatic clay wastes. A synergistic flocculation study was made to determine whether a portion of PEO could be replaced by other reagents. Several groups of reagents were tested: (1) those that increased the zeta potential of the phosphatic clay wastes; (2) those capable of hydrogen bonding; and (3) those which flocculated the phosphatic clay waste. Reduction in PEO consumption occurred only with addition of those reagents able to flocculate the slime. The use of natural guar gums resulted in a lower PEO requirement and also yielded a dewatered product of higher solids content, 43 to 45 percent, versus 33 to 35 percent obtained with PEO alone.

Jan 1, 1980

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the comparative effectiveness of three wet dust control techniques for face drilling. Previous attempts to achieve effective dust control on face drills with dry collectors have not met with success, the largest problem being sustained effective dust capture at the face. Results show that (1) foam-through-the-drill can provide 95-pct average total dust reduction in gypsum; (2) water mist-through-the-drill can provide approximately 91-pct average total dust reduction and 93-pet average respirable dust reduction in salt; (3) external boom-mounted water sprays can provide approximately 50-pet average dust reduction for both total and respirable dust in salt. The investigation showed that (1) foam and water in small quantities are very effective dust control techniques for face drills when applied through the drill steel at the point of dust generation, and (2) boom-mounted water sprays are only minimally effective for dust control on face drills.

Jan 1, 1981

By W. E. Anable

A 180° magnetic deflection residual gas analyzer mass spectrometer with a mass range of 2 to 200 amu was used to study the nature of gases evolved during arc and electron-beam melting of certain reactive and refractory metals. The partial pressure of residual gases over molten Mo, Hf, Ti, and Fe, was found to be similar: Water and hydrogen were evolved from the samples and from the furnace components, carbon dioxide and carbon monoxide resulted from deoxidation of some of the melts. Argon and acetone were residuals in the system, and methane was a decomposed organic compound from the oil diffusion pump.

Jan 1, 1969

By B. J. Scheiner

Silver ores from the Candelaria District, Nevada, and Round Mountain District, Colorado, were investigated mineralogically and metallurgically. Silver minerals of four distinct groups were identified: (1) silver sulfide; (2) argentojarosite; (3) silver contained in the iron oxide; and (4) manganese carbonate-oxide minerals, Electrooxidation and acid-chloride leaching techniques were investigated as means of altering silver minerals, and their effects on subsequent silver extraction were determined. Application of the knowledge obtained from mineral leaching studies resulted in development of a sulfur dioxide-sodium chloride leaching sequence for extracting silver from these types of ores. Silver extractions of 80 to 85 percent were obtained by leaching the ores with a sulfurous acid-sodium chloride system. This was an increase of 9 to 61 percent silver extraction over that obtained by conventional cyanidation techniques.

Jan 1, 1973

By Joseph B. Huvos

Said to be one of the world's most under-developed countries, Benin had a gross national product (GNP) estimated at $1 billion in 1980.2 Contribution of the mineral industry such as cement and limestone to the GNP was negligible, but exploration of mineral potential continued Minerals.-The United Nations Development Program (UNDP) conducted an investigation of three deposits from 1977 to 1980: Phosphates (Mekrou), gold (Perma), and chromite (Buem). A phosphate rock deposit containing about 4.5 million tons recover- able by opencast techniques was discovered. It was not known if the gold and chromite deposits were recoverable economically. Iron ore deposits of some 230 million tons near Loumbo-Loumbo are at present not exploitable because of lack of infrastructure in the northern part of the country. Geologic mapping with British and French assistance was also pursued in 1980.

Jan 1, 1982

Permit quicker, safer clearance of hang-ups in the ore passes and chutes of underground mines. Approach Develop a device that can be operated from a safe distance to explosively propel a projectile into the hang-up. How It Works The Hang-Up Clearance Module, consisting of a stand, steel disk, explosive charge, and aiming device, is placed at a location convenient for line of sight aiming at the hang-up. This placement can be more than 100 feet from the target. Once aimed, the charge is remotely detonated, and the disk is converted by explosive force into a slug and propelled to the hang-up, bringing it down. The steel disk and an explosive charge are contained by a plastic casing. A small booster which is placed at the rear center of the explosive makes up the last component of the charge. Initiation is accomplished by standard means such as detonating cord or a number 8 blasting cap. When Initiated, a detonation wave travels through the explosive, inverting and consolidating the steel disk into a large slug. This slug is propelled at high velocity to the hang-up, delivering more than 5 million foot-pounds of energy on impact.

Jan 1, 1981

By Robert C. Hickman

"INTRODUCTION The Big Four fault and the Sandy Creek fault, with several cross faults, traverse the Stalion-Curnel fluorspar prospect in a northeasterly direction. The Big Four mine, about three-quarters of a mile northeast of the prospect, is the only active mine in the immediate area.A resistivity survey was made of a portion of the prospect by the Division of Geophysical Exploration, Bureau of Mines, in May and June 1946. As a result of this survey, five holes were drilled by the Bureau of Mines during the period from October 8 to December 16, 1946. Two Longyear No. 12 Junior Straitline diamond drills were used for the work.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the supervision of Mitchell H. Kline, chief, Raleigh Branch, Mining Division."

Mar 1, 1948

Provide a low-maintenance, reliable means of generating bubbles and controlling bubble size for column flotation. Approach Commercial sparger systems used in flotation columns to process minerals provide only limited means of controlling the size of bubbles generated and the rate of air injection. Generally, these limitations are a detriment to flotation performance, particularly in recovering coarse or fine mineral particles. In addition, conventional bubble generation systems require frequent maintenance, often requiring shut-down of the column itself for repairs. To permit greater control of the bubble size generated in the flotation column and to eliminate the counter-productive problems associated with the operation of current air sparger systems, the Bureau of Mines investigated alternative methods for generating bubbles. Based on the investigation, an external bubble generation system was designed, developed, and laboratory and commercially tested.

Jan 1, 1987

Mainland China To Pay Japanese Company On Contract Claim. - Mitsubishi will receive $39 million from Red China, half of what was asked, for China's having, curtailed work on a 5369 million steel rolling mill at Baoshan near Shanghai. Copper Found in Chile. - Utah International Inc., in conjunction with Getty Oil Co., has discovered a cooper deposit in northern Chile. Early drilling reveals an enriched zone grading 1.2% to 2 3% copper. Chile already has tie world's largest Cu reserve base. Soviets To Aid Laotian Tin Industry. - The U.S.S.R. has agreed to help strengthen the tin industry in Laos, a client state. In the past, Laos has only produced small amounts of tin concentrate, 500 tons to 1,000 tons per year presumably shipped to smelters in Singapore or Penang, Malaysia. Under the agreement made in June, the Soviets are to supply equipment to increase the out put of tin from the Phontieu, Neng, and Nongsen mines and help Laos with the construction of a tin smelter. The U.S.S.R. itself is a net importer of tin, although a substantial producer of the metal.

Jan 1, 1981

By Lloyd A. Morley, Robert Stefanko

Before going directly to the analysis, it would be good to summar¬ize explosion-proof container approval methods. Both Magison (52) and Short (84) state that in general practice, the systems are certified for: 1. a rugged enclosure able to withstand an internal explosion but not allow explosively hot gases to escape, and 2. maximum surface temperature, with equipment operating inside, that will not ignite the surrounding atmosphere. Also, testing insures that any material in contact with the container surface will not be ignited by a hot spot. Associated with the first practice, the enclosures are inspected for: 1. a safe flange gap width, 2. a pressure increase during ignition, and 3. an hydrostatic pressure withstand level. The hydrostatic pressure level is almost always determined by a meas¬ured ignition-pressure test and is usually applied to prove the mechan¬ical design to some safety factor. Consequently, explosion-proof enclosure testing includes temper¬ature, permissible flame gap, and pressure. Specifications and prev¬ious research also can be similarly separated even though some interre¬lation exists between the flame gap size and internal enclosure pressure during an explosion. The Schedule 2G Sections applicable to these subjects are: 1. 18.2 Definitions; 2. 18.6 Applications;

Jan 1, 1974

By David M. Hyman

Outbursts are sudden and violent releases of gas and coal that result from a complex function of geology, stress regime, and gas pressure and content. The Bureau of Mines has reviewed methods for prediction and mitigation of such outbursts in use worldwide, as an aid in selecting the proper techniques for use in specific mine environments. Outburst-prone coal may be distinguished from normal coal by its sorption-desorption velocity. Three types of methods used to characterize the kinetics of sorption-desorption are described; all are based on the ability of outburst-prone coal to release, through desorption, methane or carbon dioxide much more rapidly than normal coals. Other prediction methods, based on borehole samples, are also described. Various mitigation methods described and evaluated include (1) working the least stressed, less disturbed, lowest gas content seam in multiple-seam areas; (2) mine opening geometry; (3) inducer shot firing; (4) water infusion; (5) localized stress relief, using boreholes or by cutting a reliever slot in the longwall face; and (6) other gas drainage methods.

Jan 1, 1987

By C. M. K. Boldt

This report summarizes five separate Bureau of Mines contract studies on the use of aerial photogrammetry, satellite transmission of in situ instrumentation information, and satellite imagery to monitor and update mine waste embankment data. The equipment used, methods applied, results, recommendations, and cost analyses are presented along with a bibliography of related investigations.

Jan 1, 1987

By H. C. Miller

[California's sensational rise to supremacy as an oil-producing State in 1923 was accompanied by a loss of 62 lives. These 62 deaths were from oil-producing accidents alone and do not include fatalities at the refineries, on tankers, or on any work not directly connected with the drilling for and the production of oil. The number of facilities for 1923 was 82 per cent greater than in 1922, the next most fatal year, with a record of 34 lives lost. The data submitted in Table 1 show that for the calendar years 1917 to 1923 inclusive, an average of 4.74 million barrels of oil were produced per Vitality in the California oil fields. On this basis, the record for 1923, hough a trifle below the average, shove up slightly better than that for 1922.]

Jan 1, 1924

By David C. Oyler, William P. Diamond

Three long horizontal holes were drilled from a directionally drilled sur¬face hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diam¬eter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a verti¬cal depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 m (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

By Edward F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged scrubbers with high dust collection efficiency for use in under-ground coal mines. The Bureau's Pittsburgh (Pa.) Research Center has developed and assisted in the development of several types of improved scrubbers that are especially suitable for various underground mining applications. Research efforts concentrated on reducing the size, power, and water consumption of these scrubbers, while optimizing their dust collection efficiency. Fractional dust collection efficiency, air volumetric range, size, power, water consumption, and application guidelines for each type are described. Air pressure differentials ranged between 2-and 3D-inches water column (wc). The dust collection efficiency of six scrubbers--a venturi, two flooded-fibrous-bed, a venturi-impaction plate, a wetted-fan, and a rotating flooded-bed--were compared. The rotating flooded-fibrous-bed and the stationary flooded-fibrous-bed scrubbers showed the highest coal dust collection efficiency. Test results show that these scrubbers can generally achieve respirable size coal dust collection efficiencies in the high 90-pct range required to reduce both long-(8-hour) and short-term coal mine dust concentrations below Federal requirements.

Jan 1, 1979

By Richard E. Hucko

The bureau of Mines conducted a laboratory scale investigation of the process of selective flocculation with the objective of developing a method to effect separations on suspensions consisting predominately of ultra-fine-size (minus 400-mesh) particles of coal and refuse. Selective flocculation of coal from coal-refuse slurries could be achieved with a wide variety of reagents. Typically as much as 15 to 20 weight-percent of high-ash solids (70 to 80 percent ash) could be retained in suspension. The flocculated sediment remained a high-ash product, however, and would require further treatment to be regarded as clean coal. No combination of reagents and conditions led to selective flocculation of the refuse component. The dispersing agent was found to be the critical factor; dosages of 3 to 8 lb/ton2 were necessary to stabilize the suspension for subsequent selective flocculation. In addition, most of the dispersants that worked were most effective at substantially elevated pH (11 or so). It was concluded that this process would be prohibitively expensive and, because of yield and quality constraints, it would be of questionable utility in today's coal preparation industry.

Jan 1, 1977

By W. M. Merritts, Charles Findlay, Stephen Krickovic

Methane emission rates were studied in a Pittsburgh coalbed mine in northern West Virginia. A fullface boring-type continuous miner, equipped with a methane monitor, was used in the development of a set of eight main headings, one side of which was near old workings; the other side abutted virgin coal. Two air splits ventilated the section. Air volumes and methane percentages were recorded, and time studies of the miner were made during five consecutive operating days, during which a complete cycle of mining the headings and one line of related breakthroughs was accomplished. Methane emission rates increased significantly as mining progressed from the side near old mine workings toward the virgin area, and generally increased with coal extract ion. Mining in the heading immediately adjacent to virgin coal was interrupted quite frequently, owing to excessive methane concentrations at the face, despite adequate air volumes and acceptable methane concentrations in the immediate return airway.

Aug 1, 1970

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980

By H. E. Sanford

"INTRODUCTION Of the occupations in and about coal mines, those of the haulage crews are among the most hazardous. Statistics indicate that the second largest number of fatalities about coal mines occurs during haulage operations and through the use or misuse of haulage equipment. Despite the fact that relatively few coal-mine employees are engaged continuously at haulage operations, approximately 20 percent of all coal-mine fatalities are attributable to haulage.Most of the hazards in haulage operations could be very greatly reduced if more serious consideration were given to the problems of the haulage crews and if sincere efforts were made to reduce the hazards. Underground haulage is similar in many respects to railroading; yet, railroading is now considered one of the safest of occupations a distinction that has been attained only by honest effort and whole-hearted cooperation on the part of all concerned. Underground haulage is also similar to street and highway operation and has in it some of the difficulties encountered in the reduction of traffic accidents the seriousness of which has not by any means been con¬trolled as yet, notwithstanding the fact that much effort has been expended through a multiplicity of laws, ordinance regulation, etc., as well as by thousands of enforcement agencies and officers.The men working on the locomotives are among the most important members of a coal-mine organization; without skilled haulage employees, the production of coal would be greatly retarded. Their jobs, particularly the job as brakeman, require physical endurance, agility, and mental and physical alertness; in thin coal beds, especially where the roof is not brushed and the coal is loaded into mine cars by hand, the need for these qualifications is greatly increased."

May 1, 1948

By Michael J. Sapko, Eric S. Weiss, Kenneth L. Cashdollar

A fundamental safety research area for the National Institute for Occupational Safety and Health (NIOSH) is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach is to develop and evaluate new and innovative seal designs that provide increased explosion protection for mining personnel. The NIOSH Pittsburgh Research Laboratory (PRL) cooperated with HeiTech Corp. of Virginia, Barclay Mowlem Construction Ltd. of Queensland, Australia, and the Mine Safety and Health Administration (MSHA) in three separate research programs to evaluate the strength characteristics and air leakage resistance of numerous innovative seal designs and ventilation control structures for use in underground coal mines. For each phase of the program, various full-scale seals, stoppings, and an overcast design were constructed in PRL's Lake Lynn Experimental Mine near Fairchance, Fayette County, PA. The seals and stoppings were built in crosscuts and were subjected to explosions to evaluate their strengths. Four pumpable cementitious seal designs ranging in thickness from 610 to 915 mm (24 to 36 in) were evaluated in the first cost-reimbursable research program with HeiTech Corp. A simple wooden framework with brattice liner was used as a form to contain the cementitious slurry during the curing period. As the seal designs decreased in thickness, higher compressive strength cementitious grout was used. All four seals withstood an explosion pressure pulse of at least 138 kPa (20 psi) while maintaining acceptable air leakage resistance. In the second cost-reimbursable research program with Barclay Mowlem Construction Ltd. of Australia, several innovative seal and stopping designs and an overcast design were evaluated. Each of the seal designs and the overcast side and wing walls used one or more air-inflated vinyl bladder assemblies anchored to the mine roof and hitched into the ribs and floor. The air within these bladders was displaced with a high-strength cementitious grout. The overcast deck consisted of a 200-mm ('7.8-in) thick reinforced cementitious slab. This was the first time that an overcast structure had been explosion tested under full-scale conditions. All of the seals, stoppings, and overcast design passed the air leakage tests before being subjected to a series of explosions with static pressure pulses ranging from 14 to 475 kPa (2 tab 69 psi). Instrumentation measured seal and overcast wall displacement as a function of time. The 450-mm (1 7.7-in) thick seal in the 2.8-m(9-ft) high third crosscut withstood an explosion pressure of 170 kPa (25 psi), but failed during a later test, which generated a peak static pressure of 475 kPa (69 psi) at the seal location. A similar 450-mm-thick seal in the 2.1-m (7-ft) high second crosscut withstood three explosion tests, which generated peak static pressures of 195, 205, and 370 kPa (28, 30, and 54 psi) at the seal location. Next, the overcast design withstood four explosions, which generated static overpressures ranging from 16 to 47 kPa (2.3 to 6.8 psi). A third program at the request of MSHA evaluated the effectiveness of using pressurized grout bags (Packsetter bags) along the mine roof and ribs in lieu of floor and rib hitching for a standard-type solid- concrete-block seal. This program was initiated to address an urlusual geological mining condition encountered when building seals in entries where required rib hitching is not a viable option due to soft friable coal. Results showed that the use of these quick-setting grout-filled Packsetter bags pressurized internally to 300 kPa (44 psi) not only provides a seal that can withstand a 138-kPa static pressure explosion, but also provides a sealing option where rib hitching is not possible.

Jan 1, 2003