Search Documents

Projected cooling requirements for ERPM led to the first proposals for the large- scale use of ice for mine cooling in the early 1980's. Following successful research into ice conveying and ice melting a large ice plant was commissioned at Harmony in 1985 and a much larger 6000 ton per day plant is presently under construction at ERPM. A brief description of the mining project is given, followed by general descriptions of the surface ice plants and the ice conveying system, the systems for using the ice for mine cooling, and the control of the whole ice cooling System.

Jan 1, 1988

Grade control is an important factor in the on-going success of a mining operation. Grade control criteria will vary depending on the commodity being mined. Financial considerations determine the actual grade control criteria at any one mine site. Mining and metallurgical capital and operating costs are ultimately used in ascertaining cut-off grades employed in grade control. The metallurgical characteristics of the ore, and ultimately the equipment selection and design of the plant, are based on samples provided by the exploration geologist. Ore variability is an important factor in designing the process plant. Ore variations, outside of those catered for in the design, as well as large ore changes on a daily basis, will impact on the metallurgical performance, and hence the economics of a mining operation. Therefore good liaison between the grade control geologist and metallurgist will undoubtedly lead to a more consistent, and more profitable mining operation.

Jan 1, 1993

By G Cormack

By designing comminution circuits for mineral liberation rather than the final recovery process and by using high mass pull gravity recovery, the concept of underground processing has become a reality. Gekko has found that many ores respond favourably to fine crushing with either high pressure grinding rolls or vertical shaft impactors which when combined with the InLine Pressure Jig gravity separator and coarse flotation results in a narrow, low-head, compact processing plant that can be sensibly fitted in existing underground openings. The focus on fine crushing reduces the power requirements of the plant to approximately 5 kWh/t for a capacity of up to 20 t/h run of mine ore feed. The use of water recycle systems places no extra load on the mineÆs normal water handling system. GekkoÆs underground processing plant, the æPythonÆ, has been designed to be towed down the decline or lowered down a shaft and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a significant operating cost-saving, lower cut-off grade and a significantly smaller environmental footprint.

Jan 1, 2008

The key elements required to maintain final wall integrity and hence slope reliability are discussed. Failure modes and mechanisms in highly structured rock slopes are then reviewed. The impact of blast disturbance on rock masses in general is discussed and the relationships between the slope failure mode and blast disturbance is then explored. The question of how designers can incorporate such impacts into the slope design process is then addressed. This necessarily involves rock mass strength consideration and two case studies are used to demonstrate a recent dilemma in this regard. Some progress regarding this dilemma has also been reported for the second case study. The major conclusions are that: Slope reliability can be severely compromised if the slopes are damaged by blasting and this impact is not often incorporated into the slope design process. The location and extent of the blast damage will impact some slope failure geometries and failure mechanisms more than others. The concept of failure mechanism specific vulnerability needs to be further developed. The evidence indicates that this aspect is even more extreme for weak ground conditions. The quantification of the reduction in rock mass strength due to blast damage is not well understood and limitations exist with some recent guidelines. The use of the Hoek-Brown criterion for slopes in blocky rock masses requires considerable judgement. Further applied developments in this regard would be very beneficial to the industry. Some promising methods to incorporate blast damage estimates into the slope design process are emerging. It is good business to minimise final wall blast damage otherwise a whole range of issues relating to reduced slope reliability emerge.

Jan 1, 1999

By Hughson B

A multi-wire borehole instrumentation system was used to monitor strata movement caused by a retreating longwall face at the Ellalong Colliery, situated in the Lower Hunter Valley in New South Wales, Mechanical anchors were placed at various horizons in the borehole which extended from the surface to the extracted coal seam. The vertical movement of the anchors was monitored during mining. The zone of major disturbance was confined to 13 times the extracted seam thickness above the seam. The average dilation of strata in this zone was 6 per cent. Above the caving zone, the tensile strain was under 2mn/m except at one location, where it was `xmi/m. The subsidence trough under dynamic conditions was flatter than that under stationary conditions. The subsidence also depended upon the extent of strata fragmentation prior to undermining.

Jan 1, 1987

The program, WASTRT 70, was set up specifically to handle the design of tunnel liners and underground structures where inter- action between rock and structure significantly affects the design. It may however be used for any mass/R.C. structure capable of being simulated by straight line elements between modes and with loading restricted to nodes. The analysis system adopts typical elastic/stiffness matrix methods. Two main mass/R.C. design segments are utilized (1) Design of section depth based on maximum required stresses and optimum steel/concrete ratios. (2) Design of reinforcement for a given section depth with concrete stresses given for mass and water code structures. Each design segment covers shear, minimum principal stress on ~ , heavy compression as per code (columns), heavy compression one-face steel (tunnel liners), tension and water code requirements for all moment/thrust/section depth ratios on rectangular sections.

Jan 1, 1976

Almost from the beginning of civilisation the inhabitants hadlearned the art of recovering and working copper to produceitems which were of use to society.From the early beginnings of the use of copper which can betraced back 6000 years and more, there has been an evolutionaryprocess accentuated in more recent times in which the art ofproducing alloys particularly with tin and latterly zinc and otherelements, has given society a wide range of useful alloys for usein industrial, domestic and architectural applications.

Jan 1, 1995

Direct measurements of liquid contents in foams obtained from (x-terpineol a-T) n-pentanol (AmOH) and n-octanol (OctOH) solutions were carried out using a column of special construction. The column enables to determine the liquid contents by cutting-off foam layers of various thicknesses and measuring amounts of liquid contained in the cut-off foam layers. Liquid contents in the whole foam layers, in the top foam layers of thickness 14 ¦ 1 mm and distribution of water alongside foam height were determined. The average liquid contents were high and reached a level of 30, 35 and 40 per cent for foams formed from cc-T, AmOH and OctOH solutions, respectively. The liquid contents in the top foam layers were much smaller. They were of an order of five per cent for a-T and AmOH and 12 per cent for OctOH. On the basis of the liquid distribution alongside foam height some practical conclusions concerning possibilities of minimising amounts of liquid contained in the collected concentrate are presented.

Jan 1, 1993

By Floyd J. M

The recovery of gold from refractory ores and concentrates can be achieved in a number of ways using roasting and leaching procedures. The Sirosmelt system introduces a new approach to the recovery of gold from these materials using smelting procedures. Laboratory studies were carried out to establish procedures for operating the Sirosmelt system for recovery of gold and associated valuable elements from an ore containing 17.5 g/t gold and a concentrate containing 22 g/t gold as well as substantial copper levels. Copper, iron, lead and matte were evaluated as collecting phases for the gold. The ore smelting procedure recovered 80-90% of the gold whilst smelting concentrate gave 98-99% gold recovery.

Jan 1, 1987

Australia contains a variety of iron ores, differing in grade, chemistry, size distribution and genesis. While a proportion of this ore is used world-wide as blast furnace lump, much of the material mined is high grade fines, requiring agglomeration (usually sintering) before blast furnace reduction. Sintering studies initially concentrated on the production of ferrous material of high iron content, coarse size and sufficient cold strength. In recent years research involving pilot plant sintering, precise test procedures and mineralogical analyses has focussed on the additional sinter properties of hot strength and reducibility. Aspects of mineralogical studies applied to iron ore sintering are described.

Jan 1, 1989

By K Matsui, R N. Gupta, H Shimada

Roof falls and failures of powered supports were major threats at longwall face. Abnormal geological conditions were caused roof falls and shield damage. Therefore continuous monitoring and analysis of strata behaviour was imperative on real time for forecasting adverse behaviour. Novel PXI instrumentation system was successfully developed for continuous monitoring and analysis of supports pressure, leg closure and gate roads convergence. However, this paper briefly examines the novel gate roads convergence monitoring system with field applications.

Jan 1, 2003

By Williams J. D

Magnetite has been used in coal processing for many years and it is likely that its use will continue well into the twenty first Century. While magnetite is only a minor cost component in coal processing, the use of processed magnetite in dense medium separation is essential to provide the split of quality coal products which the markets of today demand. The occurrence of magnetite in Australia is relatively abundant, but a combination of its iron content, magnetic properties, quality and proximity to the coal processing plants is essential to provide a low cost product for use in the Coal Industry. The demand for more splitting of coal in coal processing may require more grades of magnetite, particularly as a finer grade lower specific gravity medium to separate the finer quality low ash coals.

Jan 1, 1991

By A J. Moore

To control the airblast from blasting to regulatory limits at environmentally sensitive sites near the Collinsville Coal Mining Operations, it has been necessary for Thiess Mining to incorporate a wavefront reinforcement analysis model in the predictive environmental airblast design. Controlling airblast from cast blasting 70 m high faces with 2000-3000 kg of explosives per hole within 700 m of houses presents a considerable challenge to the blasting personnel. This paper describes the model used and summarises the results of an investigation designed to quantify the increase in airblast indicated by wavefront reinforcement diagrams to further calibrate the model for future prediction.

Jan 1, 2004

Gold and copper mineralization in the Parkes area is hosted by a meridional sequence of Late Ordovician to Early Silurian igneous and sedimentary rocks on the central northern edge of the exposed Lachlan Fold Belt. The mineralized area straddles two zones separated in part by the Parkes Thrust and exhibiting different styles of deformation and mineralization (Figure 1). The western zone is characterized by gently folded rocks, with shallow dips and weak to non-existent axial plane cleavage. Faulting is restricted to directions oblique to bedding. Numerous occurrences of minor copper mineralization are known, but of recent national importance is the discovery of the Coradgery- Goonumbla porphyry copper-gold deposits by Geopeko Ltd. A resource in excess of 250 million tonnes has been delineated (Jones, 1985), and this represents the first porphyry deposit of sufficient grade and tonnage to be potentially mineable in New South Wales. The eastern zone is much more strongly deformed. Folding is tight with strongly developed axial plane cleavage. Faulting is abundant both parallel and oblique to bedding. Quartz veining is also abundant, and a narrow belt of gold mineralization adjacent to the Parkes Thrust stretches from Forbes in the south, through Parkes and Peak Hill, to Tomingley in the north. Over 31 tonnes of gold have been produced from this gold belt, mostly before 1914, and now three deposits show good potential for redevelopment - Peak Hill, and the London-Victoria and Lachlan lines of lode.

Jan 1, 1987

In the late 1970's Western Mining Corporation, Exploration Division considered the purchase of a major multi-element spectrometer as an adjunct to our existing atomic absorption spectrophotometers. The analytical work proposed for the unit included barium, uranium and rare earth elements from Olympic Dam, uranium, sulphur, vanadium and strontium on Yeelirrie type deposits, major element and whole rock analysis, multi-element analysis of samples from the laterite, chromium and manganese exploration programmes and tin and arsenic analysis. These were all analyses that were not readily or easily performed by flame atomic absorption or were where we expected that a simultaneous multi-element instrument would be an advantage. Also the turnaround times for the commercial laboratories was considered unacceptably long for some determinations. Other factors, important when considering the spectrometer were the ability to ensure confidentiality of results and the ability to assign our own priorities and not to have to rely on commercial laboratories. The two techniques considered were X-ray Fluorescence Spectrometry and Inductively Coupled Plasma Optical Emission Spectrometry. The decision was made in favour of the ICP unit for several reasons. The ICP fitted in with our existing methodology, ie samples digested for atomic absorption or colorimetric techniques would also be suitable for ICP analysis and vice versa. The technique was suitable for water samples and for major element analyses and for rare earth elements. X-ray fluorescence spectrometers were installed at the Kambalda and Belmont laboratories and would be available to us for routine checking and for elements not suitable for ICP analysis. The final consideration was price. ICP was considerably cheaper than XRF.

Jan 1, 1987

By Gregg PEH, Stewart RB

Reclamation field trials commenced in 1985, two years before the granting of the Mining Licence. The level of pasture production on varying soil depths (0 cm, 5 cm, 15 cm and 25 cm) overlying both tailings and oxidised waste overburden was assessed. After seven years, the rate of increase of N, C, P and S, losses of S and P and pH changes were investigated on the plots where grass seed was sown into bare tailings. It was determined that on these plots it would take approximately 24 years to reach the original carbon and nitrogen levels at the mine site.

Jan 1, 1995

By Nag D. K

King Island Scheelite is a wholely owned subsidiary of Peko-Wallsend Ltd. The company works two underground mines near the southern end of King Island at the western approach to lass Strait, 240 km south of Melbourne. (See ^igure 1).

Jan 1, 1981

By Callaghan T

The Henty Gold Mine is located approximately 30 km north of Queenstown, at the head waters of the Henty River on the west coast of Tasmania at 41¦50'S, 145¦40'E on the Queenstown (SK 55-5) 1:250 000 and Sophia (8014) 1:100 000 map sheets (Figure 1). The mine is accessed from Queenstown along the A10 Highway and Anthony's Road. The town of Queenstown is located 260 km north west of Hobart on the A10 Highway, and

Jan 1, 1997

By Penny T. G

BHP Diamonds and their joint-venture participants DiaMet Minerals, Chuck Fipke and Stewart Blusson are currently developing Canada's first commercial diamond mine in the arctic barren lands of the Northwest Territories (NWT) of Canada. The paper reviews the early history of the project leading up to the discovery of the first kimberlite pipe in September 1991, diamond exploration techniques and the subsequent advanced exploration and development work carried out at the site. In many aspects, this exploration work represented a development project in itself. Coinciding with the advanced exploration work, the project team prepared an Environmental Impact Statement (EIS) and went through federal review of the project at the highest level. External affairs strategies regarding the federal review and aboriginal land claim issues were crucial components to the approval process. Upon approval in principle by the

Jan 1, 1997

By Chowdhury P. J R, Biswas S. K

Recovery of metallic values from lean-grade raw materials as well as from secondary/intermediate industrial products is of immense importance to a country like India which is not endowed with extensive sources of copper and nickel. The results of a few studies carried out in this area are described in Part-I and Part-II in this article. A novel anode casting system, specially designed for a small copper refinery which had been set up to produce copper wire bars/rods is described briefly in Part-III.

Jan 1, 1992